Sedimentation Behavior of Mixed Powder Slurry under High-Speed Centrifugal Force

Hiroyuki Y. Suzuki

doi:10.4028/www.scientific.net/MSF.631-632.361

Paper Titles

Mechanical Modeling of Thin Films Bonded to Functionally Graded Materials
p.333

Effect of Metal Gradient In Nano Wall of Stratified Type Photocatalyst
p.339

Structure of Ni-Al Intermetallic Porous Thick Films Produced by Microscopic Reactive Infiltration
p.345

The Recent Progress of FGM on Nuclear Materials - Design and Fabrication of W/Cu Functionally Graded Material High Heat Flux Components for Fusion Reactor
p.353

Sedimentation Behavior of Mixed Powder Slurry under High-Speed Centrifugal Force
p.361

Solidification Structure and Hardness Distribution in Centrifugally Cast Aluminum Alloy Duplex Pipes
p.367

Effects of the Processing Temperature of Centrifugal Casting on the Mechanical Properties of Al-Al₃Ti FGMs
p.373

Investigation of the Mechanical Properties in Al/Al₃Zr FGMs Fabricated by Centrifugal Casting Method
p.379

Creep Properties of SUS304 Steel by Small Punch Creep Tests
p.387

HomeMaterials Science ForumMaterials Science Forum Vols. 631-632Sedimentation Behavior of Mixed Powder Slurry...

Sedimentation Behavior of Mixed Powder Slurry under High-Speed Centrifugal Force

Abstract:

Compaction behavior of two component slurry during High-speed Centrifugal Compaction Process (HCP) was observed. Slight amount of iron oxide powder is mixed into alumina slurry, then the slurry was sedimented in a centrifuge under rotational speed of up to 11,500 rpm. A “Y” letter shaped flow pattern was emerged in the cross section of the compact. The pattern was clearer with higher rotational speed, but indifferent to acceleration rate of rotation. A similar pattern was simulated when we presume bidirectional initial flow in centrifugal field, which indicated that the combination of Corioli’s force and bidirectional flows of powder and dispersing medium caused such flow pattern.

You might also be interested in these eBooks

Multiscale, Multifunctional and Functionally Graded Materials

View Preview

Info:

Periodical:

Materials Science Forum (Volumes 631-632)

Pages:

361-366

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.631-632.361

Citation:

Cite this paper

Online since:

October 2009

Authors:

Hiroyuki Y. Suzuki

Keywords:

Corioli’s Force, Flow in Centrifugal Field, Functionally Graded Material (FGM), HCP, Simulation

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] H.Y. Suzuki and H. Kuroki: Metal and Mater. Int., Vol. 10 (2004), pp.185-191.

Google Scholar

[2] H. Y. Suzuki, K. Shinozaki, S. Tashima, and H. Kuroki: J. Jpn. Soc. Powder Powder Metallurgy, Vol. 51 (2004), pp.423-434 [in Japanese].

Google Scholar

[3] H. Y. Suzuki and H. Kuroki: Science of Sintering Current Problems and New Trends, Edited by M. Ristic, Serbian Academy of Science and Arts, Beograd, (2003) pp.29-36.

Google Scholar

[4] H. Y. Suzuki, K. Shinozaki, Y. Tanaka, and H. Kuroki: J. Ceram. Soc. Jpn., vol. 109, (2001), pp.137-142 [in Japanese].

Google Scholar

[5] H. Y. Suzuki, K. Shinozaki, Y. Tanaka, and H. Kuroki: J. Ceram. Soc. Jpn., vol. 109, (2001), pp.248-253 [in Japanese].

Google Scholar

[6] H.Y. Suzuki, K. Shinozaki, and H. Kuroki: Sintering Science and Technology, edited by R. M. German, G. L. Messing, and R. G. Cornwall, Penn-State Univ., (2000) pp.207-212.

Google Scholar

[7] D.T. Valentine and C.C. Jahnke: Centrifugal Mater. Processing, Edited by Regel and Wilcox, Plenum Press, New York, (1997) pp.281-297.

Google Scholar