[1]
Jong-Ok Park,Kil-Jun Kim, Dae-Yong Kang, Young-seog Lee, Young-Ho Kim. An experimental study on the optimization of powder forging process parameters for an aluminum-alloy piston[J]. Journal of Materials Processing Tech., 2001, 113(1-3):486-492.
DOI: 10.1016/s0924-0136(01)00663-x
Google Scholar
[2]
A. Thirumoorthy, T.V. Arjunan, K.L. Senthil Kumar. Latest Research Development in Aluminum Matrix with Particulate Reinforcement Composites – A Review[J]. Materials Today: Proceedings, 2018, 5(1):1657-1665.
DOI: 10.1016/j.matpr.2017.11.260
Google Scholar
[3]
Song I H, Kim D K, Hahn Y D. Investigation of Ti3AlC2 in the in situ TiC-Al composite prepared by the exothermic reaction process in liquid aluminum[J]. Materials Letters, 2004, 58(5):593-597.
DOI: 10.1016/s0167-577x(03)00576-7
Google Scholar
[4]
Dolatkhah A, Golbabaei P, Givi M K B, et al. Investigating effects of process parameters on microstructural and mechanical properties of Al5052/SiC metal matrix composite fabricated via friction stir processing[J]. Materials & Design, 2012, 37(none):458-464.
DOI: 10.1016/j.matdes.2011.09.035
Google Scholar
[5]
Jiang L, Xiaodong P, Xiangguo L, et al. The Study Status of In Situ Aluminum Matrix Composites[J]. Journal of Chongqing University (Natural Science Edition), 2003(10):1-5.
Google Scholar
[6]
Liu Z , Rakita M , Xu W , et al. Ultrasound assisted salts–metal reaction for synthesizing TiB2 particles at low temperature[J]. Chemical Engineering Journal, 2015, 263:317-324.
DOI: 10.1016/j.cej.2014.11.043
Google Scholar
[7]
Chen F, Chen Z, Mao F, Wang T, Cao Z. TiB2 reinforced aluminum based in situ composites fabricated by stir casting [J]. Materials Science and Engineering: A. 2015, 625: 357-368.
DOI: 10.1016/j.msea.2014.12.033
Google Scholar
[8]
Kumar S, Sarma V S, Murty B S . A statistical analysis on erosion wear behaviour of A356 alloy reinforced with in situ formed TiB2 particles[J]. Materials Science & Engineering: A (Structural Materials: Properties, Microstructure and Processing), 2008, 476(1-2):333-340.
DOI: 10.1016/j.msea.2007.04.113
Google Scholar
[9]
Li H , Chai L , Wang H , et al. Fabrication of TiB2/Al composite by melt-SHS process with different content of titanium powder[J]. Journal of Materials Research, 2017, 32(12):2352-2360.
DOI: 10.1557/jmr.2017.184
Google Scholar
[10]
Emamy M, Mahta M, Rasizadeh J. Formation of TiB2 particles during dissolution of TiAl3 in Al–TiB2 metal matrix composite using an in situ technique[J]. Composites ence & Technology, 2006, 66(7-8):1063-1066.
DOI: 10.1016/j.compscitech.2005.04.016
Google Scholar
[11]
Suh Y.S, Joshi S.P, Ramesh K.T. An enhanced continuum model for size-dependent strengthening and failure of particle-reinforced composites[J]. Acta Materialia, 2009, 57(19): 5848-5861.
DOI: 10.1016/j.actamat.2009.08.010
Google Scholar
[12]
Chen F, Chen Z, Mao F, Wang T, Cao Z. TiB2 reinforced aluminum based in situ composites fabricated by stir casting[J]. Materials Science and Engineering: A, 2015, 625: 357-368.
DOI: 10.1016/j.msea.2014.12.033
Google Scholar
[13]
Chen, J. H. Costan, etc. Atomic Pillar-Based Nanoprecipitates Strengthen AlMgSi Alloys.[J]. Science, 312(2006), 416-419.
DOI: 10.1126/science.1124199
Google Scholar
[14]
Zamani M, Seifeddine S, Jarfors A E W. High temperature tensile deformation behavior and failure mechanisms of an Al-Si-Cu-Mg cast alloy一The microstructural scale effect[J]. Materials & Design, 86(2015), 361-370.
DOI: 10.1016/j.matdes.2015.07.084
Google Scholar
[15]
Asghar Z, Requena G, Degischer H P , et al. Three-dimensional study of Ni aluminides in an AlSi12 alloy by means of light optical and synchrotron microtomography[J]. Acta Materialia, 2009, 57(14): 4125-4132.
DOI: 10.1016/j.actamat.2009.05.010
Google Scholar
