Microstructure and Properties of 65Mn Steel after Austenite Inverse Phase Transformation by Sub-Temperature Quenching

An Ming Li; Meng Juan Hu

doi:10.4028/www.scientific.net/AMR.194-196.89

Paper Titles

Synthesis Pathway of Dioxins in Iron Ore Sintering Process
p.71

Effect of Magnetic Field Direction on Texture Evolution in Cold-Rolled IF Steel Sheet at the Initial Stage of Recrystallization
p.75

Atomistic Model of Amorphous Silicon Nitride by Melt-Quench Method
p.80

Study on the Recrystallization Behaviour of Hot Deformed Austenite in GCr15 Bearing Steel
p.84

Microstructure and Properties of 65Mn Steel after Austenite Inverse Phase Transformation by Sub-Temperature Quenching
p.89

A Study on Microstructure of Ductile Ni-Resist Cast Iron for Exhaust Manifolds and Mechanical Property at the Condition of Altermative Thermal Cycles
p.95

Preparation of Fe-Cu-Ni-Mo-C Alloy with High Performance by Powder Metallurgy Warm Compaction
p.100

Crack Research for Welded Joint of Steel Truss Bridge
p.104

Synthesis and Dielectric Properties of Ba(Ti,Y)O₃ Solid Solutions to Ba₃Ti₂YO_8.5-BaTiO₃ Composites
p.109

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 194-196Microstructure and Properties of 65Mn Steel after...

Microstructure and Properties of 65Mn Steel after Austenite Inverse Phase Transformation by Sub-Temperature Quenching

Abstract:

The influence of sub-temperature quenching temperature on the strength and hardness of 65Mn steel during austenite inverse phase transformation is studied and the microstructure and property are analyzed. The results showed that in the range of 760~810°C , the strength and hardness of the 65Mn steel second sub-temperature quenched increased with quenching temperature increasing, reached the highest strength and hardness at 790°C quenching and then began to decrease. A small number of ferrite and ferrite dual-phase structure existed in martensite when quenching temperature was low. Fine martensite was obtained by second sub-temperature quenching due to the smaller austenitic crystal grain and austenitic nucleation sites. The mechanical properties of samples second sub-temperature quenched are better than that of conventional samples 830°C once quenched.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 194-196)

Pages:

89-94

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.194-196.89

Citation:

Cite this paper

Online since:

February 2011

Authors:

An Ming Li, Meng Juan Hu

Keywords:

Austenite, Hardness, Inverse Phase Transformation, Microstructure, Sub-Temperature Quenching, Tensile Strength

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] T. C ZHANG, etal. Mechanical Properties of 27SiMn Steel After Critical Temperature Quenching and High Temperature Tempering [J]. Heat Treatment of Metals. 2003, 8: 32-34(In Chinese).

Google Scholar

[2] Y.Z. AN. Heat Treatment Technology[M]Machine Industry Press, Beijing 1984(In Chinese).

Google Scholar

[3] G.S. WANG, Y.S. SUN. Study on Twice Quenching for Low-Carbon Dual Phase Steel[J] Journal of Dalian Jiaotong University. 2001, 22(2): 75-78(In Chinese).

Google Scholar

[4] A.M. LI. The Austenite Inverse Phase Transformation Quenching in Zero Time Holding of 25MnV Steel [J] Joumal of China Coal Society. 2006, 2(1): 129-132(In Chinese).

Google Scholar

[5] X.P. ZHAO,H.J. WAN. Application of Hypothermia Quenching on the mold components Heat Treatment of Metals Abroad. 2002, (2): 20-21(In Chinese).

Google Scholar

[6] A.M. LI. The Austenite Inverse Phase Transformation Quenching in Zero Time Holding of 25MnV Steel [J] Joumal of China Coal Society. 2006, 2(1): 129-132(In Chinese).

Google Scholar

[7] Han Jianmin, Cui Shihai,. Dual Phase Heat Treatment of Low-Alloy Steel. [J]. Iron&Stell Res Int 2005, 9 : 47-51.

Google Scholar