Surface Quality and Mechanical Properties in Drawn Stainless Steel Profile Wires Caused by Process Parameters

Marcin Kwiecień; Janusz Majta; Maciej Rumiński; Jakub Kawałko; Krzysztof Muszka

doi:10.4028/p-6697q2

Paper Titles

Determination of Forming Limit Curves - Strain Path and Failure Analysis
p.947

Investigation of the Influence by Size Effects on the Material Characterization of the Uniaxial Compression Stress State
p.955

Application of the DIC System to Build a Forming Limit Diagram (FLD) of Multilayer Materials
p.963

On the Anisotropic Mechanical Response of Ti6Al4V Sheet at High Strain Rates
p.970

Surface Quality and Mechanical Properties in Drawn Stainless Steel Profile Wires Caused by Process Parameters
p.980

Material Parameters Sensitivity on Springback Modelling of Simple Bending Process
p.992

DIC Strain Monitoring during Fatigue of Cold-Formed High Strength Steel
p.1000

Influence of the Anisotropic Behavior on Equibiaxial Paths
p.1007

Experimental Investigation of Factors Influencing the Determination of the Onset of Yielding by Temperature Measurement
p.1021

HomeKey Engineering MaterialsKey Engineering Materials Vol. 926Surface Quality and Mechanical Properties in Drawn...

Surface Quality and Mechanical Properties in Drawn Stainless Steel Profile Wires Caused by Process Parameters

Abstract:

Thin profile wires made of stainless steels are widely used for production of industrial screens used for filtration and separation processes. Industrial screens made of resistance spot welded thin profile wires are used e.g. in baskets for centrifuges or filtration screens and find a wide range of applications in various branches of the industry (mining, food and sugar industry, paper industry, wastewater treatment, oil and gas and many more). Regardless of the application, increased durability and surface quality of the screens is of paramount importance. Improvement of the longevity of manufactured items, process efficiency and environmental performance can be achieved only when interactions between initial wire rod quality and its susceptibility to metal forming operations are fully understood. Due to the complexity of the manufacturing process of industrial screens (precise and small gaps, narrow ranges of dimensional tolerances), forming of thin, so-called precision profiled wire is difficult. The influence of the charge, i.e. wire rod, parameters of the wire drawing / rolling process play a key role in obtaining semi-finished products characterized by high strength, low surface roughness and a low level of residual stresses. The paper discusses the influence of the initial state of wire rod and deformation parameters on the quality of thin austenitic and lean duplex steel profile wires as well as the possibility of replacing austenitic wires by lean duplex wires and their possible benefits.

By email Full Text Pdf

You have full access to the following eBook

Achievements and Trends in Material Forming

Read eBook

Info:

Periodical:

Key Engineering Materials (Volume 926)

Pages:

980-991

DOI:

https://doi.org/10.4028/p-6697q2

Citation:

Cite this paper

Online since:

July 2022

Authors:

Marcin Kwiecień*, Janusz Majta, Maciej Rumiński, Jakub Kawałko, Krzysztof Muszka

Keywords:

Precise Metal Forming, Stainless Steel Wires, Surface Quality

Export:

RIS, BibTeX

Permissions:

Creative Commons CC BY 4.0

* - Corresponding Author

References

[1] M. Okayasu, D. Ishida, Effect of microstructural characteristics on mechanical properties of austenitic, ferritic, and g-a duplex stainless steels, Metall Mater Trans A Phys Metall Mater Sci, 50a, (2019), 1380-1388.

DOI: 10.1007/s11661-018-5083-4

Google Scholar

[2] K. Yoshida, Technological trend and problem in wire drawing of various super fine wires, J. Jpn. Soc. Technol. Plast. 41–470 (2000) 194–198.

Google Scholar

[3] K. Yoshida, T. Shinohara, Growth and disappearance of flaws on wire surface in wiredrawing, Wire J. Int. (2004) 52–57.

Google Scholar

[4] F.C. Magalhăes, A.E.M. Pertence, H.B. Campos, M.T.P. Aguilar, P.R. Cetlin, Defects in axisymmetrically drawn bars caused by longitudinal superficial imperfections in the initial material, J. Mater. Process. Technol. 212 (2012) 237– 248.

DOI: 10.1016/j.jmatprotec.2011.09.009

Google Scholar

[5] H. Moo Baek, Y. G. Jin , S. K. Hwang, Yong-Taek Im, Il-Heon Son, Duk-Lak Lee, Numerical study on the evolution of surface defects in wire drawing, J. Mater. Process. Technol. 212 (2012) 776– 785.

DOI: 10.1016/j.jmatprotec.2011.10.028

Google Scholar

[6] T. Shinohara, K. Yoshida, Deformation analysis of surface flaws in stainless steel wire drawing J. Mater. Process. Technol. 162–163 (2005) 579–584.

DOI: 10.1016/j.jmatprotec.2005.02.125

Google Scholar

[7] B. Avitzur, B., Metal Forming: Processes and Analysis, 2nd ed. McGraw-Hill,Kierger, Huntington, NY, (1968).

Google Scholar

[8] T. S. Cao, C. Vachey, P. Montmitonnet, P.-O. Bouchard, Comparison of reduction ability between multi-stage cold drawing and rolling of stainless steel wire – Experimental and numerical investigations of damage, J. Mater. Process. Technol. 217 (2015) 30–47.

DOI: 10.1016/j.jmatprotec.2014.10.020

Google Scholar

[9] K. El Amine, J.Larsson, L. Pejryd, Experimental comparison of roller die and conventional wire drawing, J. Mater. Process. Technol.. 257 (2018) 7–14.

DOI: 10.1016/j.jmatprotec.2018.02.012

Google Scholar

[10] J.H. Ekkelenkamp, P.B. Khosrovabadi, P.B., Design and manufacture of a roller die, system for wiredrawing. Wire J. Int. 22, 27–28 30, (1989) 35–40.

Google Scholar