1. Introduction
Energy sources, such as fossil fuels (especially oil and natural gas), are used in 96% of the commodities we use on a daily basis [
1]. As oil prices have collapsed in recent years, enhanced oil recovery from existing reservoirs poses a lower risk than wildcat drilling to find new reservoirs. The oil and gas industry has witnessed an upsurge in measures aimed at increasing the oil recovery from green reservoirs [
2,
3,
4]. As part of these initiatives, waterflooding has been widely adopted as the cheapest form of recovery [
5,
6,
7,
8,
9,
10]. However, different factors affect the overall performance of this method [
11,
12,
13], including the structural setup of the reservoir and well type [
14,
15]. Thus, selecting the most suitable well type for waterflooding is essential.
Although vertical wells are commonly targeted in the early phases of drilling, more than 60% of wells currently being drilled are horizontal. Horizontal wells can (i) improve productivity, (ii) improve intersection with vertical-fracture networks, (iii) reduce gas and water coning, and (iv) increase sweep efficiency. Due to the improvement in trajectory design, the availability of bottom hole sensors, and the advancement of measuring-while-drilling (MWD) tools [
16,
17,
18,
19], well trajectories have become increasingly complex. For example, highly deviated and multilateral wells can penetrate more discrete compartments in complex reservoirs, compared with conventional wells. Such new developments require the precise identification of the most suitable well type (i.e., vertical, horizontal, multilateral, or highly deviated) for each waterflood design. Previous studies have examined the relationships between well type and oil productivity in different environments. For example, Edwards (2017) found that horizontal wells outperform vertical wells in thin formations [
20], whereas Pieters and Al-Khalifa (1991) reported that both vertical and horizontal wells have similar recoveries in layered carbonate reservoirs [
21]. Elyasi (2016) showed that for fractured reservoirs, multilateral wells have better recoveries than vertical wells, whereas deviated wells outperform horizontal wells [
22]. Ekebafe et al. (2019) reported that horizontal wells outperform deviated wells in unconsolidated formations [
23]. Using a Dykstra–Parsons model extension, Muradov et al. (2018) verified that conventional wells perform better in stratified heterogeneous reservoirs with non-communicating layers [
24]. Furthermore, Pieters and Al-Khalifa (1991) reported that neither horizontal nor multilateral wells guarantee improved oil recovery [
21]. Zadravec and Brkić (2020) discussed a unique approach to enhance oil recovery through natural dump flooding well [
25]. Intelligent completion has been installed in water injector inside the oil reservoir in the western Persian/Arabian Gulf to allow more efficient production of oil. On the basis of the successful application in this field, the authors evaluated the possibility of applying natural water dump flood in a Croatian oil field.
Despite the volume of published literature [
26,
27,
28,
29,
30,
31,
32,
33,
34,
35,
36,
37,
38] on the recovery efficiencies of different well types, to the best of our knowledge, there has been no research on the performance of highly deviated wells in the highly heterogeneous shallow reservoirs of the Central African Rift Valley region, which are significantly different from most moderate-depth to deep reservoirs in other parts of world. This is because of (i) the complications associated with drilling along a precise path within an inclined path, (ii) difficulties encountered in preventing sand influx, and (iii) challenges encountered during screen installation for sand production control, which render directional drilling more difficult and time-consuming for complex reservoirs.
The J1 Oilfield in the Central African Rift Valley region is a newly discovered oilfield with no historical data. B27 is one of three main oil-bearing reservoirs (along with B30 and B25), separated by layers of shales with non-communicating heterogeneous reservoirs and shallow burial depths (500–800 m). In addition to areal compartmentalization via faulting, pressure data indicate vertical disconnections in the oil pools. Moreover, the presence of a primary gas cap and oil near the bubble point implies that a pressure maintenance scheme is required for initial oil production; hence, waterflooding should be considered. However, the selection of a suitable well type for maximum recovery remains a challenge. Our literature review indicates that horizontal and multilateral wells are not necessarily better than vertical or deviated wells for all reservoirs or vice versa and that well type should be considered on a case-by-case basis. The selection of an appropriate well type or combination for a specific reservoir should mainly depend on reservoir properties, which impact the oil production and oil field development/production cost. In terms of the J1 Oilfield, the selection of well type is further complicated because the field is located in an ecologically sensitive area that requires a minimal environmental footprint. Thus, the target reservoir must be assessed from a different surface location while avoiding complex fault structures in the vertically disconnected sand bodies. These limitations indicate that highly deviated wells would be a better option than vertical and horizontal wells. Furthermore, the lower drilling–design cost for highly deviated wells would also render them a better option than multilateral wells for the study area, if considering all other aspects including cost reduction and reduced environmental footprint. However, the objective of this study was to investigate the performance of different well types: vertical, horizontal, multilateral, and highly deviated wells, during waterflooding of complex shallow reservoirs using the J1 Oilfield and B27 reservoir as a case study.
We used the Petrel software and ECLIPSE black oil simulator to characterize and model the B27 reservoir using published and unpublished site-specific data obtained from seismic surveys, well logs, and measurements from repeat formation tester (RFT) tools. In addition to being the first study of its kind in this region, the results of this study provide further insights into the recovery performance of highly deviated wells, compared with those of other well types, and the waterflooding of reservoirs where oil is near the bubble point. Our results provided a reference for field with similar geological setting. After economic and environmental impact analysis, this study found that highly deviated wells are a better option. This is because although the oil production from highly deviated wells is slightly lower than other cases, the footprint (environmental impact) is much smaller. This investigation also indicated that multilateral wells are not always the best candidate for oil and gas field development. Every well type has its own advantages and disadvantages in oil and gas development and production. Properties of oil and gas and reservoir characteristics play a key role in selecting the appropriate well type. A thorough study of field, design of well, simulation, production forecast, and economic analysis are necessary for field evaluation and production plan. The step-by-step procedure illustrated in this paper provided a valuable guideline to oil field development.
3. Results and Discussion
The results of the simulations are presented in
Table 8 and
Figure 10. The production performances of different well configurations were evaluated on the basis of cumulative oil production. The horizontal wells outperformed all the other well types in terms of cumulative oil recovery. This can be attributed to the single horizontal lateral section, which penetrates more pay zones, thereby creating a wide contact surface area for drainage [
55,
56]. Highly deviated wells have a similar lateral extension, but their sections are slanted. This affects oil recovery from shallow reservoirs (which are also composed of vertical non-communicating layers), resulting in the lowest recovery among the four well types (
Figure 10d). In contrast, multilateral wells should have the highest recovery because of their lateral branching structure [
57,
58]. However, these wells only exhibited the highest production during the first three years of operation before sharply decreasing to the same production rates as those of the vertical wells. This decline can be attributed to the following two factors: (1) slanting laterals reduced the contribution of vertical permeability to productivity; (2) the additional contact area between the wellbore and reservoir may have led to fluid flow resistance in shallow pay zones. However, this can be resolved with inflow control valves (ICV) in smart well configurations. The production of multilateral wells was approximately 5% higher than that of highly deviated wells. The small difference was due to the substantial cumulative exposure of laterals within the entire reservoir relative to the single sections of the highly deviated wells [
57]. Nevertheless, this effect was not pronounced because the reservoir is relatively shallow. Here, the negative effect of reduced productivity due to slanting overshadowed the positive effect of increased reservoir thickness. Well spacing significantly affects the key indicators of the field development such as the rate of liquid and oil recovery from the reservoir, completeness of oil sweep out from the producing formation, the hydrocarbons’ ultimate recovery factor, reservoir producing life, and a number of other indicators of development.
In addition, owing to the complex heterogeneity of the B27 reservoirs, permeability variations in the different parts of the reservoir and corresponding well locations partially affect the relatively small increase in the production rate. Overall, vertical wells performed better than highly deviated wells, identical to multilateral wells, and slightly poorer than horizontal wells (
Figure 10a). The improved production in the vertical wells (as compared with the highly deviated wells) can be attributed to the reservoir structure. B27 reservoirs are shallow, creating a perforation that can be easily vertically assigned in the hydrocarbon-bearing reservoir sands in different zones. This can easily increase productivity relative to the high-angle barriers in the slanted highly deviated wells. Here, J1 also has vertical pressure disconnections, which can affect the reservoir pressure and water infectivity process, particularly in unconventional wells.
3.1. Production Plots for Each Well Type
3.1.1. Vertical Wells
Figure 10a shows that, during the first 2.5 years of production, the oil production rate remained constant at 3180 Sm
3/d, and the water production was 7809.3 Sm
3/d, exhibiting a steady increase during this period. The water-cut also steadily increased to 72% at maximum production. Near the beginning of the third year of production, the oil rate declined sharply (by 55%) to 1426.1 Sm
3/d until August 2022. Water production decreased steadily over the same period. However, the water-cut steadily increased throughout waterflooding. After 2022, we observe a steady decrease in the oil production rate, leading to a cumulative oil production of 9.6 × 10
6 Sm
3. Vertical wells drilled perpendicular to the reservoir section, which in this case is a shallow reservoir, can only sweep hydrocarbons that lie directly beneath the reservoir section. Thus, we observed a sharp decrease in production after a short period of operation.
3.1.2. Horizontal Wells
Horizontal wells dug at an angle of at least 80° to a vertical wellbore are known to reach deeper pay zones and have a wide contact surface for oil drainage.
Figure 10b shows that the initial oil production rate of 3180 Sm
3/d remained constant for the first three years of production, which represents nearly six more years of production compared with the vertical wells. The water production rate increased steadily from the first year of production, reached a maximum of 11,676 Sm
3/d, and then sharply decreased to 9768.8 Sm
3/d in the final month of the first three years of production. The water-cut was as high as 78% throughout the extended period of production. The oil production rate decreased steadily until the end of waterflooding, yielding a cumulative oil production of 1.012 × 10
7 Sm
3. Cumulative oil production in the horizontal wells was 5.21% higher than that in the vertical wells.
3.1.3. Multilateral Wells
The oil production rate of the multilateral wells was maintained at a constant rate of 3180 Sm
3/d for a slightly longer period (3.5 years) compared with that for the other well types before sharply decreasing (by 66%) to 1060 Sm
3/d between 2024 and 2025 and then continuing to decrease at a steady rate for the entire flood period. In contrast, water production in the multilateral wells was higher and increased more rapidly than in the other well types, reaching a maximum production of 11,740 Sm
3/d before beginning to decline (
Figure 10c). This trend reflects the numerous laterals draining different zones at the same time, leading to high cumulative water production. Similar to all other well orientations, the water-cut in the multilateral wells also steadily increased, reaching 78% at maximum oil production. Multilateral wells drilled with more than one lateral in the reservoir section were expected to produce higher volumes, but this was not found to be the case. The cumulative oil produced was 9.54 × 10
6 Sm
3, which is similar to that produced by the vertical wells, but less oil than any other well type, including that produced by the horizontal wells.
3.1.4. Highly Deviated Wells
Unlike the horizontal wells in which we observed a repetitive fluctuation in water production rates together with a sharp decrease in oil production during the first three years, water production in the highly deviated wells (normally drilled at an angle of 78° and with a maximum angle of 81°) increased steadily from the first day of production. During this period, there was no significant decrease until production reached a maximum of 12,500 Sm
3/d. At the same time, an oil production rate of 2812.4 Sm
3/d was maintained during the first 2.5 years of production (similar to the vertical wells but not the horizontal wells), before steadily decreasing until the end of the flood (
Figure 10d). During the subsequent three years, oil production was maintained at 3180 Sm
3/d. The production rate then sharply decreased (by 62%) to 1212.4 Sm
3/d in August 2022. At this point, we observed a consistently decreasing trend in production until the end of the flood, which is similar to the other well types. The water-cut in the highly deviated wells increased steadily over time and reached 80% at maximum oil production. The cumulative oil production was 8.15 × 10
6 Sm
3/d, which indicates that production in the highly deviated wells was 15% and 19% lower than those in the vertical and horizontal wells, respectively.
3.2. Property Production Profiles for Each Well Type
3.2.1. Field Oil Production Rate
As shown in
Figure 11a, for reservoir B27, multilateral wells maintained the highest production rate followed by the horizontal wells. This better performance was a result of the horizontal and multilateral wells penetrating more of the reservoir than the vertical and highly deviated wells. However, the production of the multilateral wells declined to below that of the horizontal wells during the course of production. The additional contact area between the wellbore and reservoir reduced the resistance to fluid flow. Variations in permeability in different parts of the reservoir and corresponding well locations partially explain the relatively small increase in production rate.
3.2.2. Field Water-Cut
Figure 11b shows that the water-cut increased sharply in the four well types during the first three years of production. Subsequently, the water-cut in the vertical wells (72% of the maximum production) increased more slowly than in the horizontal and multilateral wells (78% of the maximum production), and the highest water-cut was observed in the highly deviated wells (80% of the maximum production). The total oil recovered at a 75% water-cut was highest in the horizontal wells, followed by the multilateral, vertical, and highly deviated wells. Hence, we infer that horizontal and multilateral wells will recover more oil than other well types. Highly deviated wells showed a higher water-cut than the other wells between 28 October 2018 and 24 December 2021. This was due to the structural setup of the reservoir, which enabled the inclined shape of the highly deviated wells to be in contact with more water zones than the oil-producing zones. However, by the end of the 25-year production period, the water-cut was similar between all the different well orientations (94%).
3.2.3. Field Water Injection Rate
Highly deviated wells had the highest injection rate (1.73 × 10
4 Sm
3/d), followed by the horizontal wells (1.53 × 10
4 Sm
3/d). The multilateral wells reached their maximum injection rate (1.47 × 10
4 Sm
3/d) after three years of waterflooding. The vertical wells had the lowest injection rate from the beginning of the waterflood, reaching a maximum of 1.16 × 10
4 Sm
3/d after two years of production (
Figure 11c).
3.2.4. Field Cumulative Oil Production
The cumulative oil production for the first three years in all the four well types increased steadily at the same rate from the first day of production. However, on 6 April 2020, oil production began to deviate rapidly, increasing at different steady rates for each well type. After five years of production, both the multilateral and horizontal wells had identical cumulative oil productions (5.783 × 10
6 Sm
3), the vertical wells had a cumulative production of 5.55 × 10
6 Sm
3, and the highly deviated wells had the lowest cumulative production at 5.25 × 10
6 Sm
3. Oil production in the horizontal wells steadily increased and surpassed all the other well types as time elapsed. This reflects that the drilling of horizontal wells parallel to the reservoir bedding plane resulted in a wider area of connectivity with the oil-producing formation and led to improved drainage. On 12 November 2041, after 25 years of production, the horizontal wells showed a higher cumulative oil production (1.012 × 10
7 Sm
3) than the multilateral wells, which also produced oil at a higher rate than both the vertical and highly deviated wells. However, as shown in
Figure 11d, the cumulative production in the vertical wells increased at a rapid rate with the production time. After 20 years of production, both the multilateral and vertical wells produced oil at the same rate (9.192 × 10
6 Sm
3), whereas the production rate remained the lowest for the highly deviated wells (7.88 × 10
6 Sm
3).
3.3. Field Gas Production Rate
The B27 reservoir is generally known to have low gas volumes. However, the highest maximum gas production for the four well types was observed in vertical wells (1.52 × 10
5 Sm
3/d on 6 July 2019). The multilateral, highly deviated, and horizontal wells had gas yields of less than 9.26 × 10
4 Sm
3/d (
Figure 12). Gas production lasted for only 1 year from the start of production and then began to decrease sharply for all well types.
3.3.1. Field Water Production Rate
The field water production rate increased steadily in all the well orientations right from the start of production until three years of the waterflood, when the maximum rates were obtained in all cases (
Figure 13). The highly deviated wells were shown to have the highest water production rate of 1.42 × 10
4 Sm
3/d compared to multilateral, horizontal, and vertical wells, which had their maximum at 1.18 × 10
4 Sm
3/d, 1.17 × 10
4 Sm
3/d, and 8.56 × 10
3 Sm
3/d, respectively.
3.3.2. Field Cumulative Water Production
The cumulative water production in all the four well types increased steadily at the same rate from the first day of production (
Figure 14). After the first three years, however, horizontal and highly deviated wells were exhibiting higher production than multilateral and vertical wells. By mid-July, 2020, the cumulative water production by horizontal wells increased more sharply than highly deviated wells. The deviated wells’ production went on decreasing while the production in the other three well types was steadily increasing, with multilateral at a faster rate than the vertical wells. By July 2020, the production in horizontal wells was 3.5 × 10
7 Sm
3, while both multilateral and highly deviated wells had the same production at 3.0 × 10
7 Sm
3. Beyond this date, the multilateral water production increased rapidly, surpassing that of the highly deviated wells. Moreover, by the end of the production time, vertical wells had the least production followed by highly deviated wells. Meanwhile, horizontal wells had the highest cumulative water production at 5.0 × 10
7 Sm
3, then followed by multilateral (4.5 × 10
7 Sm
3).
3.4. Recovery Efficiency
Identifying the recovery factor or recovery efficiency of different well orientations was the main objective of this study. We observed that recovery efficiency was identical (12%) for all well types after three years of production (
Figure 15). As oil production continued, there was a steady increase in the recovery efficiency for all well scenarios; however, there were important differences. For example, recovery from horizontal wells increased at a higher rate than that for all other well types, reaching a maximum of 33% after 25 years of waterflooding. Multilateral wells had the next highest recovery, which was maintained for most of the waterflood period. However, after 20 years of production, both the vertical and multilateral wells exhibited the same recovery factor (31%), which was maintained for the last five years of the waterflood. Highly deviated wells had the lowest recovery factor of all well types (26%). The J1 Oilfield is a recent discovery with limited data and no historical data. Therefore, there remain numerous uncertainties in the oil–water and gas–oil contact sets. Hence, further investigations will be necessary after 3–5 years of active oil production. Moreover, while we acknowledge that numerous types of multilateral wells exist, here, we only considered dual lateral well types, given that they deliver better performance in shallow reservoirs [
22].
3.5. Well Type Selection
The selection of the well type to develop reservoirs is based on environmental impact, the oil recovery factor and cost to develop, and ability produce oil and gas. Our study confirms that horizontal and multilateral wells are not necessarily better than vertical or deviated wells for all reservoirs or vice versa. The application of different well types should be on a case-by-case basis. The cost difference (i.e., well drilling and the corresponding ongoing operating costs) should also be considered. Usually, the cost of a horizontal well is 1.5–3 times that of a vertical well, depending on its lateral length. The cost of multilateral wells depends on the number of laterals and the length of each lateral. As technology advances, it requires less rig time per well and lower related costs for materials, services, number of casings, and size of the wellbore, among other factors. The advancement of drilling technology has allowed drilling to target reservoirs using complicated well structures and measurements while also ensuring that the well trajectory remains with the target reservoir. These factors significantly reduce the uncertainty while drilling in areas with complex geological structures. In summary, the cumulative oil production, cost, and environmental impact are the dominant factors that affect the selection of the well type. It is necessary to conduct a thorough economic analysis before making a final decision. In this study, the difference in the oil recovery by four well types were small. Considering the higher well cost for horizontal wells and high environmental impact by vertical wells, we chose highly deviated wells for these green reservoirs locating in ecologically sensitive environments.
3.6. Well Spacing
Well spacing significantly affects the key indicators of the field development such as the rate of liquid and oil recovery from the reservoir, completeness of oil sweep out from the producing formation, the hydrocarbons’ ultimate recovery factor, reservoir producing life, and a number of other indicators of development. Generally, small well spacing, which means more well numbers to develop the field, can accelerate oil production and increase recovery efficiency, but with the cost of higher investment and drop in net present value (NPV). Large well spacing that reduces well numbers to develop the field can lead to lower capital and operating costs, but with the expense of low production rate and low recovery factor. There is an optimum well spacing that can result in maximum NPV for project. It can be determined through a thorough study of field, design of well, simulation, production forecast, and economic analysis.
3.7. Economic Analysis
In addition to the environmental impact, economics is another key factor when selecting the appropriate well type and well spacing. One critical indicator used in the project ranking is NPV. Generally, the well type that causes minimum environmental impact and maximum NPV should be chosen. Under the circumstance that several cases have similar NPV, the one that has minimum environmental impact is ranked first. If environmental impact is equal, the case providing maximum NPV should be considered. The most complicated or difficult scenario is that there are two extreme cases, within which other cases lie. One extreme case has maximum NPV with maximum environmental impact, while another extreme case has minimum NPV with minimum environmental impact. Under this condition, the advantages and the disadvantages of each case should be scrutinized. A thorough review of environmental impact should be conducted, and a regulation agency should be consulted before any decision can made. The appropriate development plan can be chosen after a comprehensive evaluation of geology and engineering uncertainty, economic benefit, environmental and social impact, and geopolitical risk. NPV or rate of return (ROR) is often used in the economic analysis. To calculate NPV or ROR, revenue and cost are considered. Revenue is calculated from oil/gas price and production. In this work, productions of four well types were used. The cost includes exploration, development, production, and abandonment costs. Exploration cost includes the seismic acquisition, data processing, interpretation, geology analysis, experiment on rock and fluid, petrophysical and geophysical study, wildcat and appraisal well drilling and completion, well logging, and well test. Development cost consists of capital cost for drilling campaign for producer and injector, surface and subsurface facilities, and pipeline to transport oil–gas–water. Production cost can be divided into fixed operating cost and variable operating cost. Fixed operating cost will not vary significantly during the production while variable operating cost is proportional to the oil–gas–water production. For onshore fields, fixed operating cost can vary from 40% to 80% of total operating cost. For offshore fields, percentage of fixed operating cost is higher, from 50% to 90%. Workover and/or well intervention service required to maintain production should be taken into account in production cost. Re-perforation cost is a part of operation cost, while deepening of existing wellbore to penetrate and produce deeper reservoir is classified as capital investment in a project. Abandonment cost is needed when reservoirs are depleted and the field ceases production or production is no long economic. The cost is to plug the wells and to restore the wellsite to original conditions. In addition to cost, some projects require the operator to pay a royalty to the mineral rights owner, which means the mineral rights owner can have a portion of hydrocarbon without paying any cost. This portion of production should be excluded in the gross revenue calculation. Net revenue then is calculated from the gross revenue and cost. Tax calculation is applied on the net revenue to obtain the after-tax cash flow. NPV is obtained by utilizing discounts rate. In this project, except for the size of the footprint (or environmental impact), hydrocarbon production and drilling completion cost were the main variables in the economic analysis of four well types in order to develop the target field. Through a systematically comprehensive evaluation of geology/reservoir, production, economic impact, and environmental impact, we found that highly deviated wells were the appropriate well type to produce in the studied field.
4. Conclusions
Few studies consider the application of this well type in the shallow green reservoirs of the Central and East African Rift Valley region. This is the first study of its kind in the region. We evaluated the performance of highly deviated wells, in comparison with three other well types. Horizontal wells had the highest cumulative oil production at 10.2 million Sm3, whereas other well types produced less than 9.5 million Sm3. The horizontal and multilateral wells yielded the highest oil production rates, whereas the lowest rates were observed for the highly deviated wells. Highly deviated wells were found to be an appropriate well type for non-communicating vertically non-concentrated stacked reservoirs or complex faulted reservoirs in this study, on the basis of reservoir simulation, production forecast, economic analysis, and environmental impact evaluation. This is because although the oil production from highly deviated wells is slightly lower than other cases, the footprint (environmental impact) is much smaller.
The study provides broad insights into the performance of various well types during waterflooding of green shallow heterogeneous reservoirs with vertical pressure disconnections, operated under similar operating conditions. For shallow reservoirs, multilateral wells are not always a suitable option because they have faster water breakthrough, increasing water production rates. Consequently, laterals may block fluid flow owing to vertical discontinuity. In such cases, the negative effect of reduced productivity owing to slanting outweighs the positive effect of increased reservoir thickness exposure. Additionally, multiple branches in shallow non-communicating zones may cause pressure fields around drain holes to interfere with each other, lowering the effective drawdown.
The results of this study provide a reference for reservoirs with unique characteristics, including those that are green, shallow, highly heterogeneous, and have complex faulted reservoirs with non-communicating pressure systems that require special production/injection plans characterized by very early injection. In shallow green reservoirs, water injection is implemented in the very early stages of field production. This imposes high risk to the reservoir as pressure has not been depleted, and unconsolidated to semi-consolidated reservoirs are easily fractured by waterflooding. This study illustrates a special case study for the successful development of a rare reservoir type. This is different from many other studies that model waterflooding during middle or later stages of oil production from moderate-depth or deep reservoirs. This research can be used as a reference for future research on similar reservoirs.
The observations from this study can aid in future decision-making and field development planning. Moreover, it serves as a successful practical example of the application of waterflooding as an initial recovery mechanism for green reservoirs, where oil is near the bubble point pressure. Before investment decisions are made for waterflooding in the J1 Oilfield, the operational costs associated with the well type that yields the highest oil recovery should be investigated. Thus, increasing oil recovery should not be the only prerequisite in economic/profitability analyses as is often the case in the selection of horizontal well configurations. Future studies should also examine other multilateral well types, particularly given the geological heterogeneity, structure, and location of the J1 oil reservoir. Moreover, as the J1 Oilfield is a recent discovery with no historical data, numerous uncertainties still exist in the oil–water and gas–oil contact sets. As such, further investigations will be necessary after 3–5 years of active oil production.