Thermal Science 2022 Volume 26, Issue 4 Part A, Pages: 2981-2989
https://doi.org/10.2298/TSCI2204981E
Full text ( 957 KB)
Cited by
Analysis of thermal barrier coated pistons in the COMSOL and the effects of their use with water + ethanol doped biodiesel
Ertugrul Ishak (Department of Mechanical Engineering, Mus Alparslan University, Mus, Turkey), o.ulkir@alparslan.edu.tr
Ulkir Osman (Department of Mechanical Engineering, Mus Alparslan University, Mus, Turkey)
Ozer Salih (Department of Mechanical Engineering, Mus Alparslan University, Mus, Turkey)
Ozel Serkan (Department of Mechanical Engineering, Bitlis Eren University, Bitlis, Turkey)
In this study, the thermal analysis of an aluminum piston coated with MgOZrO2
to create a thermal barrier with the COMSOL multiphysics program and the
changes in exhaust gas temperature, fuel consumption, and engine torque
values obtained as a result of engine test experiments were examined. For
this purpose, the MgOZrO2 coated and uncoated piston engine was started with
biodiesel and 5% water + 15% ethanol doped biodiesel fuel at engine speeds
of 1000 rpm, 1500 rpm, 2000 rpm, and 2500 rpm. In the thermal analysis
results obtained in the COMSOL, it was found that the temperature values
increased in the upper regions of the coated pistons. Likewise, in engine
experiments, increased exhaust gas temperature and engine torque showed a
tendency to decrease fuel consumption values. It has been observed that the
data obtained in the analysis in the COMSOL program are in parallel with the
results of the engine experiments.
Keywords: COMSOL Multiphysics, thermal barrier coating, engine test, biodiesel
Show references
Szwaja, S., et al., Investigation on Ethanol-Glycerol Blend Combustion in the Internal Combustion Sparkignited Engine, Engine Performance and Exhaust Emissions, Fuel Processing Technology, 226 (2022), 107085
Luo, Q. H., et al., Experimental Investigation of Combustion Characteristics and NOx Emission of a Turbocharged Hydrogen Internal Combustion Engine, International Journal of Hydrogen Energy, 44 (2019), 11, pp. 5573-5584
da Costa, R. B. R., et al., Combustion, Performance and Emission Analysis of a Natural Gas-Hydrous Ethanol Dual-Fuel Spark Ignition Engine with Internal Exhaust Gas Re-Circulation, Energy Conversion and Management, 195 (2019), Sept., pp. 1187-1198
Feng, D., et al., Combustion Performance of Dual-Injection Using n-Butanol Direct-Injection and Gasoline Port Fuel-Injection in a SI Engine, Energy, 160 (2018), Oct., pp. 573-581
Hernandez, J. J., et al., Effect of Partial Replacement of Diesel or Biodiesel with Gas From Biomass Gasification in a Diesel Engine, Energy, 89 (2015), Sept., pp. 148-157
Ramasamy, D., et al., Engine Performance, Exhaust Emission and Combustion Analysis of a 4-Stroke Spark Ignited Engine Using Dual Fuel Injection, Fuel, 207 (2017), Nov., pp. 719-728
Gautam, S. S., et al., Thermal Barrier Coatings for Internal Combustion Engines: A review, Materials Today: Proceedings, 51 (2022), 3, pp. 1554-1560
Hegab, A., et al., Plasma Electrolytic Oxidation Thermal Barrier Coating for Reduced Heat Losses in IC Engines, Applied Thermal Engineering, 196 (2021), 117316
Kogo, T., et al., High Efficiency Diesel Engine with Low Heat Loss Combustion Concept-Toyota’s Inline 4-Cylinder 2.8-Liter Estec 1GD-FTV Engine (No. 2016-01-0658), SAE Technical Paper, 2016.
Aliramezani, M., et al., Modelling, Diagnostics, Optimization, and Control of Internal Combustion Engines via Modern Machine Learning Techniques: A Review and Future Directions, Progress in Energy and Combustion Science, 88 (2022), 100967
Rajkumar, S., et al., Integration of Artificial Neural Network, Multi-Objective Genetic Algorithm and Phenomenological Combustion Modelling for Effective Operation of Biodiesel Blends in an Automotive Engine, Energy, 239 (2022), 121889
Iurk, M. A., et al., Maximizing Volumetric Efficiency Using Stochastic Optimization Techniques for Internal Combustion Engines, Applied Thermal Engineering, 199 (2021), 117603
Yaglı, H., et al., Optimisation of Simple and Regenerative Organic Rankine Cycles Using Jacket Water of an Internal Combustion Engine Fuelled with Biogas Produced from Agricultural Waste, Process Safety and Environmental Protection, 155 (2021), Nov., pp. 17-31
Ortiz-Imedio, R., et al., Comprehensive Analysis of the Combustion of Low Carbon Fuels (Hydrogen, Methane and Coke oven Gas) in a Apark Ignition Engine Through CFD Modelling, Energy Conversion and Management, 251 (2022), 114918
Mansor, M. R. A., et al., Numerical Investigation on Combustion and Emissions in a Direct Injection Compression Ignition Engine Fuelled with Various Hydrogen-Methane-Diesel Blends at Different Intake Air Temperatures, Energy Reports, 7 (2021), Suppl. 5, pp. 403-421
Zhang, W., et al., Application of Two-Phase Pulsating Flow in Organic Rankine Cycle System for Diesel Engine Waste Heat Recovery, Energy, 243 (2022), 122776
Zhang, W., et al., Numerical Analysis and Optimization Design of Fin-and-Tube Evaporator in Organic Rankine Cycle System for Diesel Engine Waste Heat Recovery, International Journal of Heat and Mass Transfer, 175 (2021), 121376
Meng, X., et al., CombustionS of Partially Gasified Willow and DDGS Chars Using TG Analysis and COMSOL Modelling, Biomass and Bioenergy, 39 (2012), Apr., pp. 356-369
Hassan, M. A. S. M., et al., Approach to Enhance the Heat Transfer of Valve Seats through Thermal Analysis, Applied Thermal Engineering, 202 (2012), 117870
Fatoba, O. S., et al., Numerical Modelling and Effects of Reinforcement Addition on the Microstructural Evolution of Additive Manufactured Ti-6Al-4V Alloy, Materials Today: Proceedings, 18 (2019), 7, pp. 2832-2839
Raja, E., et al., An Influence on Prospis Juliflora (PF) oil Biodiesel of Thermal Barrier Coated in Compression Ignition Engine, Materials Today: Proceedings, On-line first, http://doi.org/10.1016/j.matpr.2021.12.249, 2022
Elumalai, P. V., et al., Experimental Investigation Reduce Environmental Pollutants Using Biofuel NanoWater Emulsion in Thermal Barrier Coated Engine, Fuel, 285 (2021), 119200
Erdogan, S., et al., Operational Evaluation of Thermal Barrier Coated Diesel Engine Fueled with Biodiesel/Diesel Blend by Using MCDM Method Base on Engine Performance, Emission and Combustion Characteristics, Renewable Energy, 151 (2020), May, pp. 698-706
Mohapatra, D., et al., Effect of Steam Injection and FeCl3 as Fuel Additive on Performance of Thermal Barrier Coated Diesel Engine, Sustainable Environment Research, 28 (2018), 5, pp. 247-255
Vural, E., et al., Thermal Analysis of a Piston Coated with SiC and MgOZrO2 Thermal Barrier Materials, International Journal of Scientific and Technological Research, 1 (2015), Jan., pp. 43-51
Vural, E., Thermal Analysis of Al2O3, TiO2, and SiC Coatings Combustion of a Diesel Engine Piston 3-D Finite Element Method, International Journal of Scientific and Technological Research, 1 (2015), 6, pp. 20-30
Ozdemir, M. R., et al., Energy, Exergy and Exergo-Economic Characteristics of Hydrogen Enriched Hydrocarbon-Based Fuels in a Premixed Burner, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 43 (2021), 23, pp. 3119-3136
Yan, Z., et al., A Parametric Modelling Study of Thermal Barrier Coatings in Low-Temperature Combustion Engines, Applied Thermal Engineering, 200 (2022), 117687
Zhang, Y., et al., Effect of SCR Downsizing and Ammonia Slip Catalyst Coating on the Emissions from a Heavy-Duty Diesel Engine, Energy Reports, 8 (2022), Nov., pp. 749-757
Aydin, S., et al., Investigation of the Usability of Biodiesel Obtained From Residual Frying oil in a Diesel Engine with Thermal Barrier Coating, Appl. Therm. Eng., 80 (2015), Apr., pp. 212-219
Barik, D., et al., Effects of Diethyl Ether (DEE) Injection on Combustion Performance and Emission Characteristics of Karanja Methyl Ester (KME) - Biogas Fueled Dual Fuel Diesel Engine, Fuel, 164 (2016), Jan., pp. 286-296