Processing and Application of Ceramics 2022 Volume 16, Issue 2, Pages: 97-105
https://doi.org/10.2298/PAC2202097X
Full text (
1445 KB)
Cited by
Oxidation resistance performance of SiC-AlON ceramic composites at high temperature
Xiao Lai Rong (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China + Key Laboratory of Non-ferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha, PR China)
Xiao Yu Xiang (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Zhao Xiao Jun (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China), zhaoxj@csu.edu.cn
Li Xing (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Chen Lv Ming (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Xuan Tu Xiao (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Zhang Ya Fang (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Cai Zhen Yang (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China)
Wang Xiao Feng (School of Materials Science and Engineering, Central South University, Changsha, Hunan, PR China), wangxiaofeng@csu.edu.cn
The microstructure and oxidation behaviour of the pure AlON ceramics and 8
wt.% SiC-AlON composite were investigated at 700-1500°C. With increasing
oxidation temperature, the surface morphology of two ceramics showed a
change from acicular to flaky-like and then to granular features. With the
addition of nanosized SiC particles, the oxidation resistance of the
ceramics was remarkably enhanced above 1100°C. This is attributed to the
formation of a dense oxide layer composed of Al2O3, SiO2 and mullite, which
could cover the whole matrix and suppress further penetration of oxygen. Due
to the dense oxide layer, the oxidation kinetics of the 8 wt.% SiC-AlON
composites conformed to a parabolic law, while that of the pure AlON
conformed to a linear law. After oxidation at 1500 °C for 40 h, the weight
gain of the 8 wt.% SiC-AlON composites was 3.07mg/cm2, which was only 22.5%
of that of the pure AlON.
Keywords: AlON, SiC, microstructure, oxidation behavior
Show references
N. Zhang, B. Liang, X.Y.Wang, H.M. Kan, K.W. Zhu, X.J. Zhao, “The pressureless sintering and mechanical properties of AlON ceramic”, Mater. Sci. Eng. A, 528 [19-20] (2011) 6259-6262.
M.X. Liu, C.F. Liu, J. Zhang, R. Tao, Q. Zhang, Q. Qi, “Microstructure and mechanical properties of BN-Si3N4 and AlON joints brazed with Ag-Cu-Ti filler alloy”, J. Eur. Ceram. Soc., 38 [4] (2018) 1265-1270.
H.X. Willems, M.M.R.M Hendrix, R. Metselaar, G. de With, “Thermodynamics of AlON I: Stability at lower temperatures, J. Eur. Ceram. Soc., 10 [4] (1992) 327-337.
J.W. McCauley, P. Patel, M.W Chen, G. Gilde, E. Strassburger, B. Paliwal, K.T. Ramesh, D.P. Dandekar, “AlON: A brief history of its emergence and evolution”, J. Eur. Ceram. Soc., 29 [2] (2009) 327-337.
N.D. Corbin, “Aluminum oxynitride spinel: A review”, J. Eur. Ceram. Soc., 5 [3] (1989) 143-154.
L.M. Goldman, R. Twedt, S. Balasubramanian, S. Sastri, “ALON optical ceramic transparencies for window, dome, and transparent armor applications”, Proc. SPIE, 8016 (2011) 77-77.
Y. Oishi, W.D. Kingery, “Self-diffusion of oxygen in single crystal and polycrystalline aluminum oxide”, J. Chem. Phys., 33 [2] (1960) 480-486.
X.D. Dang, W. Meng, R. Zhang, K.K. Guan, B.B. Fan, W.M. Long, M. Jia, H.S. Zhang, “Crucial effect of SiC particles on in situ synthesized mullite whisker reinforced Al2O3-SiC composite during microwave sintering”, Process. Appl. Ceram., 11 [2] (2017) 106-112.
K. Balazsi, M. Furko, Z. Fogarassy, “Examination of milled h-BN addition on sintered Si3N3/h-BN ceramic composites”, Process. Appl. Ceram., 12 [4] (2018) 357- 365.
D.X. Li, Z.H. Yang, D.C. Jia, C.C. Hu, B. Liang, Y. Zhou, “Preparation, microstructures, mechanical properties and oxidation resistance of SiBCN/ZrB2-ZrN ceramics by reactive hot pressing”, J. Eur. Ceram. Soc., 35 [16] (2015) 4399-4410.
P. Xiao, Z.C. Li, L. Pan, Z.Y. Liu, B.G. Zhang, Z. Li, Y. Li„ “Effect of powdered h-BN as addition on the microstructure and mechanical properties of C/C composites fabricated by chemical vapor infiltration”, Mater. Sci. Eng. A, 743 (2019) 707-715.
Y.C. Si,M. Xia, H.X. Li, H.G. Sun, A. Guo, Y.H. Du, S.X. Zhao, X.L. Shang, Y.Q. Chen, “Co-effects of oxidation of SiC aggregates on the sintering behaviour and microstructures of SiC-CaAl12O19 composite refractories”, Process. Appl. Ceram., 15 [1] (2021) 11-18.
X.J. Zhao, D.L. Chen, H.Q. Ru, N. Zhang, B. Liang, “Oxidation behaviour of nano-sized SiC particulate reinforced AlON composites”, J. Eur. Ceram. Soc., 31 [13] (2011) 2255-2265.
X.J. Zhao, N. Zhang, H.Q. Ru, B. Liang, D.L. Chen, “Mechanical properties and toughening mechanisms of silicon carbide nano-particulate reinforced AlON composites”, Mater. Sci. Eng. A, 538 (2012) 118-124.
M.G. Persova, Y.G. Soloveichik, V.K. Belov, D.S. Kiselev, D.V. Vagin, P.A. Domnikov, I.I. Patrushev, D.N. Kurskiy, “Modeling of aerodynamic heat flux and thermoelastic behavior of nose caps of hypersonic vehicles”, Acta Astronautica, 136 (2017) 312-331.
S. Kumar, S.P. Mahulikar, “Aero-thermal analysis of lifting body configurations in hypersonic flow”, Acta Astronautica, 126 (2016) 382-394.
W. Huang, J. Liu, Z.X. Xia, “Drag reduction mechanism induced by a combinational opposing jet and spike concept in supersonic flows”, Acta Astronautica, 115 (2015) 24- 31.
Z. Zhang, Y. Liu, Z. Jiang, “Effect of vibration exctiation on hypersonic aeodynamic and aerothermodynamic”, Chinese J. Theor. Appl. Mechan., 49 [3] (2017) 616-626.
M. Hamidouche, N. Bouaouadja, C. Olagnon, G. Fantozzi, “Thermal shock behavior of mullite ceramic”, Ceram. Int., 29 [6] (2003) 599-609.
B.B. Fan, W. Li, B.Z. Dai, K.K. Guan, “Preparation of mullite whiskers reinforced SiC/Al2O3 composites by microwave sintering”, Process. Appl. Ceram., 10 [4] (2016) 243-248.
J.Q. Qi, J.C. Zhou, W. Pang, J.F. He, Y.Y. Su, Z.J. Liao, D.X. Wu, T.C. Lu, “Study on the preparation of AlON powder by solid state reaction method”, Rare Metal Mater. Eng., 36 (2007) 88-91.
P. Goeuriot, D. Goeuriot-Launay, F. Thevenot, “Oxidation of an Al2O3-AlON ceramic composite”, J. Mater. Sci., 25 (1990) 654-660.
D. Lao, P. Lin, X.J. Liu, R.Y. Chen, W.B. Jia, M.H. Li, D.Q. Hei, “A novel approach to prepare high strength and high porosity reticulated porous ceramics by in-situ synthesis of mullite whiskers”, Ceram. Int., 47 [10] (2021) 14561-14568.
Q. Jia, H. Zhang, S. Li, X. Jia, “Effect of particle size on oxidation of silicon carbide powders”, Ceram. Int., 33 [2] (2007) 309-313.
J.C. Mauro, “Thermodynamics vs. kinetics”, pp. 1-17 in Materials Kinetics, Elsevier, Amsterdam, The Netherlands, 2021.
E. Kotomin, V. Kuzovkov, “General conclusion”, pp. 593- 595, Ch. 10 in Comprehensive Chemical Kinetics book series Vol. 34 “Modern Aspects of Diffusion-Controlled Reactions”. Eds. E. Kotomin, V. Kuzovkov, Elsevier, 1996.
W. Xie, Q.G. Fu, C.Y. Cheng, P.P Wang, J. Li, N.N. Yan, “Effect of Lu2O3 addition on the oxidation behavior of SiC-ZrB2 composite coating at 1500 °C: Experimental and theoretical study”, Corros. Sci., 192 (2021) 109803.
K. Ramachandran, Z. Carmine, K. Yoshida, T. Tsunoura, D.D. Jayaseelan, “Experimental investigation and mathematical modelling of water vapour corrosion of Ti3SiC2 and Ti2AlC ceramics and their mechanical behaviour”, J. Eur. Ceram. Soc., 41 [9] (2021) 4761-4773.
Z.W. Tong, R.J. He, T.B. Cheng, K.Q. Zhang, D.W. Dai, Y.Z. Yang, D.N. Fang, “High temperature oxidation behavior of ZrB2-SiC added MoSi2 ceramics”, Ceram. Int., 44 [17] (2018) 21076-21082.
G.P. Zhang, J. Sun, Q.G. Fu, “Microstructure and oxidation behavior of plasma sprayed WSi2-mullite-MoSi2 coating on niobium alloy at 1500 °C”, Surf. Coat. Technol., 400 (2020) 126210.
Z.Y. Cai, Y.H. Wu, H.Y. Liu, G.Y. Tian, R. Pu, S.M. Piao, X.Y. Tang, S.N. Liu, X.J. Zhao, L.R. Xiao, “Formation and oxidation resistance of a new YSZ modified silicide coating onMo-based alloy”, Mater. Des., 155 (2018) 463-474.
L.R. Xiao, X.Q. Xu, S.N. Liu, Z.Q. Shen, S.Y. Huang, W.T. Liu, Y.Q. Peng, Y.L. Huang, J.F. Liu, Y.C. Nie, X.J. Zhao, Z.Y. Cai, “Oxidation behaviour and microstructure of a denseMoSi2 ceramic coating on Ta substrate prepared using a novel two-step process”, J. Eur. Ceram. Soc., 40 [10] (2020) 3555-3561.
M. Susa, K. Nagata, “Thermal oxidation of silicon substrates through oxygen diffusion”, Mater. Sci. Eng. A, 146 [1-2] (1991) 51-62.
J.Y. Du, Y.L. Li, F.Y. Li, X.J. Ran, X.Y. Zhang, X.X. Qi, “Research on the high temperature oxidation mechanism of Cr3C2-NiCrCoMo coating for surface remanufacturing”, J. Mater. Res. Technol., 10 (2021) 565-579.
T. Hatakeyama, S. Ida, N. Sekido, K. Yoshimi, “Significant improvement of the oxidation resistance of MoSiBTiCbased multiphase alloys by Ti enrichment”, Corros. Sci., 176 (2020) 108937.
G. Chen, H. Wang, H.Y. Sun, Y.Y. Zhang, P. Cao, J. Wang, “Effects of Nb-doping on the mechanical properties and high-temperature steam oxidation of annealing FeCrAl fuel cladding alloys”, Mater. Sci. Eng. A, 803 (2021) 140500.
W. Shao, C. Zhou, “Oxidation behavior of the B-modified silicide coating on Nb-Si based alloy at intermediate temperatures”, Corros. Sci., 132 (2018) 107-115.