Development of a solar colleсtor based on aluminum construction heat pipes

Authors

DOI:

https://doi.org/10.15587/2312-8372.2019.190119

Keywords:

solar collector, aluminum structural heat pipe, aluminum flat absorber panel, aluminum cylindrical absorber panel

Abstract

The object of research is the thermal efficiency of solar collectors based on aluminum structural heat pipes. Solar collectors with heat pipes have a structurally similar design. The heat-absorbing panel secures the heat pipes to the evaporation zone, and the condensation zones are located in the battery tank. The differences are only in the designs of the absorption panels, the areas of the condensation zones and the heat carriers of the heat pipes. One of the most problematic places of research is the justification and development of a new design of a heat-absorbing solar collector panel based on heat pipes.

A review of the publications showed that a solar collector based on aluminum structural heat pipes operating in the two-phase thermosyphon mode has a heat loss when transmitting radiation heat exchange in the long-wavelength range between the absorbing flat panel and the heat pipe. The project of a solar collector with a new, absorbing solar rays panel is proposed. To analyze the efficiency of the solar collector based on aluminum structural heat pipes with a new absorption panel, two models of solar collectors were created – with a flat absorber panel and a cylindrical absorber panel.

The models of solar collectors based on one aluminum structural heat pipe fixed on aluminum flat and aluminum cylindrical absorption surfaces are investigated by the method of thermophysical experiment.

The results of studies of the efficiency of solar collector models are presented. The thermal efficiency of a new solar collector based on an aluminum structural heat pipe with a cylindrical absorbing panel in the initial period of heating water is up to 1 5 % higher than that of a solar collector with a flat absorbing panel, and at the end of heating up to 4 %. The cylindrical surface of the panel plays the role of a concentrator of the reflected part of the radiation and the own radiation of the panel in the region of the heat pipe.

Further studies are planned to be conducted in the direction of optimization of the geometric parameters of the heat-absorbing surfaces of solar collectors.

Author Biographies

Vladimir Marinenko, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" 37, Peremohy ave., Kyiv, Ukraine, 03056

PhD, Associate Professor

Department of Nuclear Power Stations and Engineering Thermophysics

Vladyslav Kulynych, National Technical University of Ukraine " Igor Sikorsky Kyiv Polytechnic Institute" 37, Peremohy ave., Kyiv, Ukraine, 03056

Postgraduate Student

Department of Nuclear Power Stations and Engineering Thermophysics

References

  1. Bezrodny, M. K., Pioro, I. L., Kostyuk, T. O. (2005). Transfer Processes in Two-phase Thermosyphone Systems. Theory and Practice. Kyiv: Augmented and Revised Edition. Fact, 704.
  2. Peterson, G. P. (1994). An Introduction to Heat Pipes: modelling, testing and application. Wiley, 356.
  3. Gaugler, R. S. (1966). Pat. No. 3229759 US. Evaporation – condensation heat transfer devise. Declareted: 02.12.1963; published: 18.01.1966.
  4. Reay, D. A., Kew, Р. A. (2006). Heat Pipes. Fifth Edition, 374.
  5. Semena, M. G., Gershuni, A. N., Zaripov, V. K. (1984). Teplovye truby s metallovoloknistymi kapilliarnymi strukturami. Kyiv: Vischa shkola, 214.
  6. Singh, R., Mochizuki, M., Nguyen, T., Akbarzadeh, A. (2011). Application of heat pipes in energy conservation and renewable energy-based systems. Frontiers in Heat Pipes, 2, 033003, 1–13.
  7. Vasiliev, L. L. (1988). Heat pipes in the systems with renewable energy sources. Science and technology. Minsk, 7–35.
  8. Walker, A., Mahjouri, F., Stieler, R. (2004). Evacuated-Tube Heat-Pipe Solar Collectors Applied to the Recirculation Loop in a Federal Building. NREL Report, No. CP-710-36149, 9.
  9. Rassamakin, B. M., KHairnasov, S. M., Zaripov, V. K. (2012). Razrabotka i issledovanie teplovykh trub novogo profilia dlia solnechnykh kollektorov s ispolzovaniem selektivnogo pokrytiia pogloschaiuschei poverkhnosti. Otchet po NIR. KPI im. Igoria Sikorskogo – 2434 – p; Nomer gosregistracii temy – 0111U000567. Kyiv.
  10. Khairnasov, S. M. (2010). Eksperimentalnoe issledovanie effektivnogo ploskogo solnechnogo kollektora na teplovykh trubakh. Vozobnovliaemaia energiia, 2 (21), 35–39.
  11. Marinenko, V. І. (2017). Pat. No. 118736 UA. Element soniachnogo kolektora. MPK F24J 2/04. No. u 201701760; declareted: 04.02.2017; published: 28.08.2017, Biul. No. 16.
  12. Marinenko, V. I. (2018). Pat. No. 123808 UA. Soniachnii pidigrivach vody. MPK: F24C 15/00. No. u 201709169; declareted: 18.09.2017; published: 12.03.2018, Bul. No. 5.

Downloads

Published

2019-11-21

How to Cite

Marinenko, V., & Kulynych, V. (2019). Development of a solar colleсtor based on aluminum construction heat pipes. Technology Audit and Production Reserves, 6(1(50), 42–46. https://doi.org/10.15587/2312-8372.2019.190119

Issue

Vol. 6 No. 1(50) (2019): Industrial and technology systems

Section

Reports on research projects

License

Copyright (c) 2020 Vladimir Marinenko, Vladyslav Kulynych

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.