This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
In-Cylinder Soot Deposition Rates Due to Thermophoresis in a Direct Injection Diesel Engine
Annotation ability available
Sector:
Language:
English
Abstract
An investigation of the mechanism causing in-cylinder soot deposition in a direct injection diesel engine was carried out. First, an analytical study was undertaken to determine which of following possible deposition mechanisms, thermophoresis, Brownian diffusion, turbulent diffusion, inertial impingement, or electrophoresis were responsible for the deposition of the soot on the combustion chamber walls. Based on a series of numerical models comparing each mechanism under conditions typical of diesel engine combustion, thermophoresis was singled out as the most likely cause of in-cylinder soot deposition.
Second, an experiment was performed to test the hypothesis that the soot deposition was caused by thermophoresis. An optical probe was designed to fit an access port in the cylinder head of a Cummins NH250 single cylinder test engine. The probe was designed such that a sapphire optical access window was positioned flush with the combustion chamber surface when the probe was installed. The probe incorporated the capability of changing the temperature of the window surface approximately 100øC when the engine was operating at: 1300 rpm, an equivalence ratio of 0.3, and an intake pressure of 27 psi.
A thermocouple was placed near the window to measure the temperature. A fiber optic cable carried the combustion radiation signal, transmitted through the window, to a photodiode detector. The photodiode signal was amplified and then recorded by a high speed data acquisition system. In the testing sequence, the engine was first motored at 1300 rpm and then the fuel was turned on. The radiation signal was then recorded for the next 1600 cycles and was observed to attenuate as soot accumulated on the window. The transmittance of the soot layer on the window, , was calculated by assigning the initial peak voltage radiation signal recorded to Io and the signal measured subsequent to this to I[. Using light scattering theory, the transmittance was then applied to the calculation of the mass deposited on the window. The results from the experimental study show that the soot deposition rate was, on average, 46.9% higher when the window was cooled versus uncooled. These results were consistant with the earlier predictions that thermophoresis is a main contributor to the soot deposits on the in-cylinder surfaces.
Recommended Content
Authors
Citation
Suhre, B. and Foster, D., "In-Cylinder Soot Deposition Rates Due to Thermophoresis in a Direct Injection Diesel Engine," SAE Technical Paper 921629, 1992, https://doi.org/10.4271/921629.Also In
References
- Alkidas, A.C. “Heat Release Studies in a Divided-Chamber Diesel Engine,” ASME Technical Paper No. 85-DGP-22 1985
- Alkidas, A.C. Cole R.M. “Thermal Loading of a Divided-Chamber Diesel Engine,” SAE Technical Paper No. 831325 1983
- Boggs, D. Borman G.L. “Calculation of Heat Flux Integral Length Scales from Spatially-resolved Surface Temperature Measurements in an Engine,” SAE Technical Paper No. 910721 1991
- Bohren, C.F. Huffman D.R. Absorption and Scattering of Light by Small Particles Wiley-Interscience New York 1983
- Brock, J.R. “On the Theory of Thermal Forces Acting on Aerosol Particles,” Journal of Colloid Science 17 768 780 1962
- Collings, N. Baker N. Wolber W.G. “Real-time Smoke Sensor for Diesel Engines,” SAE Paper No. 860157 1986
- Crump, J.G. Seinfeld J.H. “Turbulent Deposition and Gravitational Sedimentation of an Aerosol in a Vessel of Arbitrary Shape,” Journal of Aerosol Science 12 5 405 415 1981
- Davies, C.N. “Deposition From Moving Aerosols,” Ch. XII in Aerosol Science Davies C.N. Academic Press London 1966
- Doeblelin, E.O. Measurement Systems, Applications and Design McGraw-Hill New York 1990
- Du, C.J. Kittelson D.B. “Total Cylinder Sampling From a Diesel Engine: Part III - Particle Measurements,” SAE Paper No. 830243 1983
- Eisner, A.D. Rosner D.E. “Experimental Studies of Soot Particle Thermophoresis in Nonisothermal Combustion Gasses Using Thermocouple Response Techniques,” 61 153 166 1985
- Epstein, P.S. “On the Resistance Experienced by Spheres in Their Motion Through Gasses,” Physical Review 23 710 733 1924
- Farrell, P.V. Verhoeven D.D. “Heat Transfer Measurements in a Motored Engine Using Speckle Interferometry,” SAE Paper No. 870456 1987
- Ferguson, C.R. Tree D.R. DeWitt D.P. Wahiduzzaman S.A.H. “Design, Calibration and Error Analysis of Instrumentation for Heat Transfer Measurements in Internal Combustion Engines,” Developments in Experimental Techniques in Heat Transfer and Combustion ASME New York 67 82 1987
- Fukuda, M. Tree D.R. Foster D.E. Suhre B.R. “The Effect of Aromatic Content and Structure on Direct Injection Diesel Particulates,” SAE Paper No. 920110 1992
- Gaffney, J. Sapienza R. Butcher T. Krishna C. Marlow W. O'Hare T. “Soot Reduction in Diesel Engines: A Chemical Approach,” Combustion Science and Technology 24 89 92 1980
- Heywood, J.B. Internal Combustion Engine Fundamentals 626 648 McGraw-Hill New York 1988
- Holman, J. P. Heat Transfer McGraw-Hill New York 1986
- Kerker, M. The Scattering Light and Other Electromagnetic Radiation Academic Press Orlando 1969
- Kishi, Y. Tohno H. Ara M. “Characteristics and Combustibility of Particulate Matter,” SAE Paper No. 920687 1992
- Kittelson, D.B. Ambs J.L. Hadjkacem H. “Particulate Emissions from Diesel Engines: Influence of In-Cylinder Surface,” SAE Paper No. 900645 1990
- Kittelson, D.B. Pui D.Y.H. Moon K.C. “Electrostatic Collection of Diesel Particles,” SAE Paper No. 860009 1986
- Kittelson, D.B. Collings N. “Origin of the Response of Electrostatic Particle Probes,” SAE Paper No. 870476 1987
- Klein, S.A. EES Manual 1991
- Lee, S.C. Tien C.L. “Optical Constants of Soot In Hydrocarbon Flames,” Eighteenth Symposium (International) on Combustion The Combustion Institute 1981
- Lucht, R.P. Maris M.A. “CARS Measurement of Temperature Profiles Near a Wall in an Internal Combustion Engine,” SAE Paper No. 870459 1987
- Lucht, R.P. Dunn-Rankin D. Walter T. Dreier T. Bopp S.C. “Heat Transfer in Engines: Comparison of CARS Thermal Boundary Layer Measurements and Heat Flux Measurements,” SAE Paper No. 910722 1991
- Mackel, D.B. Kennedy I.M. “Experimental and Numerical Investigation of Soot Deposition in Laminar Stagnation Point Boundary Layers,” Twenty-third Symposium (International) on Combustion/The Combustion Institute 1551 1557 1990
- Mohammad, I.S.A. “Simultaneous Pyrometer Measurements Along Three Path Directions in an Open Chamber Diesel,” University of Wisconsin-Madison 1990
- Murray, R.G. “Performance and Emission Characteristics of a Semi-Adiabatic Engine,” ASME Technical Paper No. 80-DGP-44 American Society of Mechanical Engineers New York 1980
- McDonald, J.R. “Construction and Testing Facility for Diesel Engine Heat Transfer and Particulate Research,” University of Wisconsin-Madison 1984
- Needham, J.R. Doyle D.M. Faulkner S.A. Freeman H.D. “Technology for 1994,” SAE Paper No. 891949 1989
- Park, C. Appelton J.P. “Shock Tube Measurements of Soot Oxidation Rates,” Combustion and Flame 20 369 379 1973
- Rosner, D.E. Chemically Reacting Flow Systems Butterworths, Boston 1986
- Schweimer, G.W “Ion Probe, in the Exhaust Manifold of Diesel Engines,” SAE Paper No. 860012 1986
- Stevenson, R. “Morphology and Crystallography of Diesel Particulate Emissions,” Carbon 20 359 365 1982
- Talbot, L. Cheng R.K. Schefer R.W. Willis D.R. “Thermophoresis in a Heated Boundary Layer,” Journal of Fluid Mechanics 101 737 758 1980
- Tree, D.R. 1992
- Waldmann, L. Schmitt K.H. “Thermophoresis and Diffusiophoresis of aerosols,” Ch. IV in Aerosol Science Davies C.N. Academic Press London 1966
- Yan, J. “Analyses and In-Cylinder Measurements of Local and Hemispherical Particulate Radiant Emissions and Temperature in a Direct Injection Diesel Engine,” University of Wisconsin-Madison 1988