This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Split-Spray Piston Geometry Optimized for HSDI Diesel Engine Combustion
Technical Paper
2003-01-0348
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A combustion chamber geometry design optimization study has been performed on a high-speed direct-injection (HSDI) automotive diesel engine at a part-load medium-speed operating condition using both modeling and experiments. A model-based optimization was performed using the KIVA-GA code. This work utilized a newly developed 6-parameter automated grid generation technique that allowed a vast number of piston geometries to be considered during the optimization. Other salient parameters were included that are known to have an interaction with the chamber geometry. They included the start of injection (SOI) timing, swirl ratio (SR), exhaust gas recirculation percentage (EGR), injection pressure, and the compression ratio (CR). The measure of design fitness used included NOx, soot, unburned hydrocarbon (HC), and CO emissions, as well as the fuel consumption. Subsequently, an experimental parametric study was performed using the piston geometry found by the numerical optimization. The model-based optimum design parameters were used as a starting point for the experiments. Parameters varied included the SOI timing, EGR, SR, boost pressure, and injection pressure. The resulting design features a novel chamber geometry that is demonstrated to be able to achieve low emissions.
Recommended Content
Authors
Topic
Citation
Wickman, D., Yun, H., and Reitz, R., "Split-Spray Piston Geometry Optimized for HSDI Diesel Engine Combustion," SAE Technical Paper 2003-01-0348, 2003, https://doi.org/10.4271/2003-01-0348.Also In
References
- Boulouchos, K. “Strategies for Future Engine Combustion Systems - Homogeneous or Stratified Charge ?” SAE 2000-01-0650 2000
- Akihama, K. Takatori, Y. Inagaki, K. Sasaki, S. Dean, A., M. “Mechanism of the Smokeless Rich Diesel Combustion by Reducing Temperature” SAE 2001-01-0655 2001
- Hotta, Y. Nakakita, K. Fuyuto, T. Inayoshi, M. Fujiwara, K. Sakata, I. “Cause of Exhaust Smoke and Its Reduction Methods in an HSDI Diesel Engine Under High-Speed and High-Load Conditions” SAE 2002-01-1160 2002
- Kimura, S. Aoki, O. Kitahara, Y. Aiyoshizawa, E. “Ultra-Clean Combustion Technology Combining a Low-Temperature and Premixed Combustion Concept for Meeting Future Emission Standards” SAE 2001-01-0200 2001
- Wickman, D. D. Senecal, P. K. Reitz, R. D. “Diesel Engine Combustion Chamber Geometry Optimization Using Genetic Algorithms and Multi-Dimensional Spray and Combustion Modeling” SAE 2001-01-0547 2001
- Zolver, M. Griard, S. Henriot, S. “3D Modeling Applied to the Development of a DI Diesel Engine: Effect of Piston Bowl Shape” SAE 971599 1997
- Lee, T. Reitz, R. D. “Response Surface Method Optimization of a HSDI Diesel Engine Equipped With a Common Rail Injection System” 37-1 2001 Fall Technical Conference ASME 2001
- Senecal, P. K. Reitz, R. D. “Simultaneous Reduction of Engine Emissions and Fuel Consumption Using Genetic Algorithms and Multi-Dimensional Spray and Combustion Modeling” SAE 2000-01-1890 2000
- Tennison P.J. “An Experimental Investigation of the Effects of Common Rail Injection Parameters on Emissions and Performance in a High Speed Direct Injection Small Bore Diesel Engine” Dept. of Mechanical Engineering, University of Wisconsin-Madison 1998
- Hamosfakidis, V. Reitz, R. D. “Optimization of a Hydrocarbon Fuel Ignition Model” Combustion and Flame 2001
- Tanin, K. V. Wickman, D. D. Montgomery, D. T. Das, S. Reitz, R. D. “The Influence of Boost Pressure on Emissions and Fuel Consumption of a Heavy-Duty Single-Cylinder Diesel Engine” SAE 1999-01-0840 1999
- Lee, T. “An Experimental Study of Emission Reduction Mechanisms in a High Speed Direct Injection Diesel Engine with Multiple Injections and EGR” Dept. of Mechanical Engineering, University of Wisconsin-Madison 2002
- Gish, R. E. McCullough, J. D. Retzloff, J. B. Mueller, H. T. “Determination of True Engine Friction” SAE 580063 1958
- Yun, H. Reitz, R. D. “An Experimental Study on Emissions Optimization Using Micro-Genetic Algorithms in a HSDI Diesel Engine” SAE 2003-01-0347 2003
- Amsden, A. A. “KIVA-3V: A Block-Structured KIVA Program for Engines with Vertical or Canted Valves” Los Alamos National Laboratory Report No. LA-13313-MS 1997
- Senecal, P. K. “Development of a Methodology for Internal Combustion Engine Design Using Multi-Dimensional Modeling with Validation Through Experiments,” University of Wisconsin-Madison 2000
- Han, Z Reitz, R. D. “Turbulence Modeling of Internal Combustion Engines Using k- ε Models,” Combust. Sci. and Tech. 106 267 1995
- Han, Z. Reitz, R. D. “A Temperature Wall Function Formulation for Variable-Density Turbulence Flows with Application to Engine Convective Heat Transfer Modeling,” Int. J. of Heat and Mass Transfer 40 613 1997
- Sarre, C. Kong, S.-C. Reitz, R. D. “Modeling the Effects of Injector Nozzle Geometry on Diesel Sprays,” SAE 1999-01-0912 1999
- Rutland, C. J. Eckhause, J. Hampson, G. Hessel, R. Kong, S. Patterson, M. Pierpont, D. Sweetland, P. Tow, T. Reitz, R. D. “Toward Predictive Modeling of Diesel Engine Intake Flow, Combustion, and Emissions,” SAE 941897 1994
- Halstead, M. Kirsh, L. Quinn, C. “The Autoignition of Hydrocarbon Fuels at High Temperatures and Pressures - Fitting of a Mathematical Model,” Combust. Flame 30 45 1977
- Kong, S.-C. Han, Z. Reitz, R. D. “The Development and Application of a Diesel Ignition and Combustion Model for Multidimensional Engine Simulation,” SAE 950278 1995
- Hiroyasu, H. Kadota, T. “Models for Combustion and Formation of Nitric Oxide and Soot in DI Diesel Engines,” SAE 760129 1976
- Nagle, J. Strickland-Constable, R. F. “Oxidation of Carbon Between 1000-2000 C,” Proc. of the Fifth Carbon Conf. 1 154 1962
- Bowman, C. T. “Kinetics of Pollutant Formation and Destruction in Combustion,” Prog. Energy Combust. Sci. 1 33 1975
- Patterson, M. A. Kong, S.-C. Hampson, G. J. Reitz, R. D. “Modeling the Effects of Fuel Injection Characteristics on Diesel Engine Soot and NOx Emissions,” SAE 940523 1994
- Zhu, Y. Reitz, R. D. “A 1-D Gas Dynamics Code for Subsonic and Supersonic Flows Applied to Predict EGR Levels in a Heavy-Duty Diesel Engine” Int. Journal of Vehicle Design 1998
- Senecal, P. K. Uludogan, A. Reitz, R. D. “Development of Novel Direct-Injection Diesel Engine Designs using Computational Fluid Dynamics,” SAE 971594 1997
- Wickman, D. D. Tanin, K. V. Senecal, P. K. Reitz, R. D. Gebert, K. Barkhimer, R. L. Beck, N. J. “Methods and Results from the Development of a 2600 Bar Diesel Fuel Injection System,” SAE 2000-01-0947 2000
- Montgomery, D. T. Reitz, R. D. “Optimization of Heavy-Duty Diesel Engine Operating Parameters Using A Response Surface Method” SAE 2000-01-1962 2000
- Affes, H. Trigui, N. Smith D. Griaznov, V. “Shape Optimization of IC Engine Ports and Chambers,” SAE 980127 1998
- Pilley, A. D. Beaumont, A. J. Robinson, D. R. Mowll D. “Design of Experiments for Optimization of Engines to Meet Future Emissions Targets,” 27 th Int. Symposium on Automotive Technology and Automation 1994
- Carroll, D. L. “Chemical Laser Modeling with Genetic Algorithms,” AIAA Journal 34 338 1996
- Coello Coello, C. A. Christiansen, A. D. Santos Hernandez, F. “A Simple Genetic Algorithm for the Design of Reinforced Concrete Beams,” Engineering with Computers 13 185 1997
- Edwards, S. P. Pilley, A. D. Michon, S. Fournier, G. “The Optimization of Common Rail FIE Equipped Engines Through the use of Statistical Experimental Design, Mathematical Modelling and Genetic Algorithms,” SAE 970346 1997
- Krishnakumar, K. “Micro-Genetic Algorithms for Stationary and Non-Stationary Function Optimization,” 1196 Intelligent Control and Adaptive Systems 1989
- Carroll, D. L. “Genetic Algorithms and Optimizing Chemical Oxygen-Iodine Lasers,” Developments in Theoretical and Applied Mechanics 18 411 1996
- Krieger, R. B. Siewert, R. M. Pinson, J. A. Gallopoulos, N. E. Hilden, D. L. Monroe, D. R. Rask, R. B. Solomon, A. S. P. Zima, P. “Diesel Engines: One Option to Power Future Personal Transportation Vehicles” SAE 972683 1997
- Stodolsky, F. Gaines, L. Marshall, L. An, F. Eberhardt, J. “Total Fuel Cycle Impacts of Advanced Vehicles” SAE 1999-01-0322 1999
- Klingbeil, A. E. Juneja, H. Ra, Y. Reitz, R. D. “Premixed Diesel Combustion Analysis in a Heavy-Duty Diesel Engine” SAE 2003-01-0341 2003
- Takeda, Y. Keiichi, N. Keiichi, N. “Emissions Characteristics of Premixed Lean Diesel Combustion with Extremely Early Staged Fuel Injection” SAE 961163 1996
- Nagel, Z. W. “On the Modeling of Turbulence Generation in HSDI Diesel Engines using the RNG k-e Model” Dept. of Mechanical Engineering, University of Wisconsin-Madison 2002
- Truant, M. Dehoux, S. Gastaldi, P. “CFD for Combustion Chamber Development: Influence of Valve Pockets on the Combustion Process” THIESEL conference Valencia, Spain 2002
- Choi, C. Y. Reitz, R. D. “An Experimental Study on the Effects of Oxygenated Fuel Blends and Multiple Injection Strategies on DI Diesel Engine Emissions” FUEL 78 1303 1317 1999
- Yi, Y. Reitz, R. D. “Modeling the Effect of Primary Atomization on Diesel Engine Emissions” SAE 2003-01-1041 2003
- Kong, S.-C. Reitz, R. D. “Use of Detailed Chemical Kinetics to Study HCCI Engine Combustion With Consideration of Turbulent Mixing Effects” ASME Journal of Eng. for Gas Turbines and Power 124 702 707 July 2002