Evaluation of Partial Volume Effect Correction Methods for Brain Positron Emission Tomography: Quantification and Reproducibility Materials and Methods Correction Methods for Pve Region-based Method: R-pvc Voxel Based Methods: M-pvc, Mg-pvc and A-pvc

This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract Quantitative accuracy of positron emission tomography (PET) is decreased by the partial volume effect (PVE). The PVE correction (PVC) methods proposed by Alfano et al., Rousset et al., Müller-Gärtner et al. and Meltzer et al. were evaluated in the present study to obtain guidelines for selecting among them. For accuracy evaluation, the Hoffman brain phantom was scanned with three PETs of differing spatial resolution in order to measure the effect of PVC on radioactivity distribution. Test-retest data consisting of duplicate dynamic emission recordings of the dopamine D2-receptor ligand [ 11 C] raclopride obtained in eight healthy control subjects were used to test the correction effect in different regions of interest. The PVC method proposed by Alfano et al. gave the best quantification accuracy in the brain gray matter region. When the effect of PVC on reliability was tested with human data, the method of Meltzer et al. proved to be the most reliable. The method by Alfano et al. may be better for group comparison studies and the method by Meltzer et al. for intra-subject drug-effect studies. Positron emission tomography (PET) is a medical imaging method that records the simultaneous emission of gamma rays from the point of positron-electron annihilation in living tissue. Neuroreceptors and cerebrometabolic pathways can be targeted with specific tracers which bear positron-emitting isotopes in their chemical structure. Unfortunately, despite the good quantitative capabilities of PETs, the PET imaging technique suffers from relatively poor spatial resolution, which impairs the spatial localization of the radioactivity signals and also results in the so-called partial volume effects (PVE). As a result of PVE, the quantitative accuracy of PET images is reduced. The PVE smoothes PET images so that some of the radioactivity from regions of higher concentration is mis-attributed to adjacent regions of lower activity. In brain imaging with tracers of high radioactivity in brain gray matter (GM), PVE yields lower radio activities than their real values for GM structures and higher radioactivity values for the brain white matter (WM). As a result of this, the radioactivity concentration values are differently variated in different regions of interest (ROI) of the brain. The main correlating element for PVE is the size of the image resolution, which is mainly …

annihilation in living tissue.Neuroreceptors and cerebrometabolic pathways can be targeted with specific tracers which bear positron-emitting isotopes in their chemical structure.Unfortunately, despite the good quantitative capabilities of PETs, the PET imaging technique suffers from relatively poor spatial resolution, which impairs the spatial localization of the radioactivity signals and also results in the so-called partial volume effects (PVE).As a result of PVE, the quantitative accuracy of PET images is reduced.The PVE smoothes PET images so that some of the radioactivity from regions of higher concentration is mis-attributed to adjacent regions of lower activity.In brain imaging with tracers of high radioactivity in brain gray matter (GM), PVE yields lower radio activities than their real values for GM structures and higher radioactivity values for the brain white matter (WM).As a result of this, the radioactivity concentration values are differently variated in different regions of interest (ROI) of the brain.
The main correlating element for PVE is the size of the image resolution, which is mainly determined by the crystal size, the ring diameter of the tomograph and the travel distance of the positron.The travel distance before annihilation degrades the resolution, and it correlates with the kinetic energy of the positron of the used tracer.Other contributing factors include the size and shape of the radioactivity source and the signal-to-noise ratio of the PET image.In addition to the physical causes of PVE, also the computational methods that are used in order to reconstruct the PET image can induce PVE in the resulting image.These include histogramming and reconstruction from coincidence raw data to sinogram data, sinogram data reconstruction to PET images and image post-filtering after reconstruction of the PET images.
Various methods for partial volume effect correction (PVC) have been proposed.The method reported by Meltzer et al. [1] corrects the radioactivity values of the conjunction of the WM and GM regions.The methods of Müller-Gärtner [2] and Alfano et al. [3] process the WM and GM regions separately and use an estimate of the true WM mean radioactivity when correcting the radioactivity values of the GM region.Modifications of these two methods have also been proposed.[4] Rousset et al. [5] have proposed a method for correcting the mean activity values of ROIs.Most methods mentioned above have been further refined in subsequent years, [6,7] and the robustness of the PVC methods against errors in their processing steps such as MRI-PET co-registration and MRI segmentation has also been considered in several studies.[8][9][10][11] The method of Meltzer et al. has been reported to be robust to errors in preprocessing and in homogeneities in the PET image.[10] It is notable that the methods amplify the existing noise.[12] An increase of variance in the time-activity curves has been reported when using the method by Rousset et al. [13] If the noise is amplified too much, the usefulness of recovering the regional mean radioactivity values decreases.Therefore, both the effect of PVC on noise and on the accuracy of the mean values of ROIs should be evaluated.Further, when dispersion in image voxels is high, it is difficult to conclude whether small differences in images or regions originate from real differences in the studied objects, or if they are caused by the data-collecting and reconstruction processes.[14] The PET method is typically used in group comparison studies and intra-subject drug effect studies.The application of a PVC method is sensible if it is capable of revealing the true differences between the groups and between the scans regardless of the added noise.
In the present study, testing with a phantom object was done using three different tomographs (GE Advance, GE DSTE and Siemens HRRT) to reveal differences in the noise amplification between the PVC methods proposed by Alfano et  filled chambers can be used.For a phantom object, the radioactivity concentration and distribution are accurately known.Phantoms allow the use of a real tomograph, but the anatomy still differs from that of a real brain.Our approach is to use both phantom and real human studies in the evaluation of PVC methods.This is done in order to obtain more reliable results than would be achieved either with real human subjects or with a phantom alone.Results of real human PET studies also show whether the reproducibility and reliability of the corrected values have decreased between scans.With phantom tests, we can confirm that the results of human studies are not affected by systematic errors.The robustness of correction methods against errors in the structural image segmentation and co-registration to the PET image were not tested here, because such an evaluation has already been done elsewhere.[11,16] For accuracy evaluation, the Hoffman brain phantom filled with [ 18 F] FDG was scanned with three different PET tomographs when evaluating the effect of the PVC on the radioactivity distribution in the case where the actual radioactivity level is known.The test-retest data set consisted of dynamic emission studies of eight healthy human volunteers.Each study consisted of two injections of [ 11 C] raclopride with a time separation of at least 2 h.The half life of 11 C is 20.3 min.All subjects gave informed written consent for their participation in these studies, which were approved by the Ethical Committee of the local health district.The evaluated PVC methods use additional structural information from the imaged object to find the boundaries of the regions to be corrected.For this, computerized tomography (CT) images were used with the phantom object and magnetic resonance imaging (MRI) images with the human subjects.The segmentation of the phantom CT image was performed semiautomatically.The MRI images were segmented with an automatic method that uses predefined probability maps for the segments.PET to MRI co-registration and MRI segmentation were done with SPM2 software (UCL Institute of Neurology, UK, http://www.fil.ion.ucl.ac.uk/spm/software/spm2).
The software used for PVC and the SPM2 were used without GUI to exclude all user interaction.This reduces the time and computational resources needed and makes it possible to run the tests as batch jobs.All images used in the evaluation were converted to Analyze 7.5 image file format before correction.

Correction methods for PVE
The PVE is generally modeled as a convolution of the real radioactivity values with the point spread function (PSF) and some additional noise: The PSF values are measured by taking a PET image of a point-shaped radioactivity source in air to derive the distribution of the signal in the transaxial and axial directions.The width at one half of the maximal peak height (referred to as FWHM, full width at half maximum) is used as an estimate of the PSF.Another interpretation of FWHM is that it gives the smallest distance between two resolved points such that they can still be distinguished from each other.In this paper, a constant FWHM value for each tomograph is used across transaxial and axial directions for PSF.This is used at the expense of loss of accuracy, but it saves computational resources.[16] The same approach is used for all PVC methods under evaluation, and therefore it is not expected to bias the results.Formula (2-1) cannot be solved with deconvolution methods directly, because of the contribution of noise term.However, several solutions have been proposed for this problem.In the present work, we focus on PVC methods that are applied to the reconstructed image.These methods can be divided into region-based methods that The image is then used as a divisor for the voxel values of the region to be corrected.The effect of the PVC on the reproducibility of PET imaging has so far been evaluated only for the M-PVC and MG-PVC methods, with the less sophisticated M-PVC appearing to give better results.[16] However, this method is known to be less accurate compared to the MG-PVC method, which can be seen as a more general solution to the PVC problem.

Region-based method: R-PVC
In the R-PVC method, the mean radioactivity values I Finally, the true radioactivity concentration at the conjunction of GM and WM regions I PET act,GM + WM is multiplied by the convoluted mask to produce the observed PET image.In this method, the considerable radioactivity in the observed PET image is assumed to originate only from GM and WM regions.
Therefore, the equation can be rewritten as: Evaluation of partial volume effect correction methods for brain positron emission tomography... http://www.ncbi.nlm.nih.gov/pmc/articles/PMC3000501/?report=printableThis method produces a PVE-corrected image containing the composition of GM and WM, with the assumption that the radioactivity concentration is uniformly distributed in these areas.
When ROIs lie mainly within the GM region, it is possible to apply the correction method to that area, assuming that radioactivity is uniformly distributed in the GM and WM regions and that the mean radioactivity of WM is known.In MG-PVC, the observed radioactivity distribution I

Summary of correction methods
The above-mentioned assumptions made for the correction methods should be approximately correct for obtaining reliable results inside the GM and WM regions in real applications.Inhomogeneities inside the GM and WM mean that PVE exists also inside them.This does not affect the mean radioactivity concentration, but it changes the values for smaller ROIs inside them.The A-PVC method can be seen as a compromise between region-based and voxel-based methods; and it is assumed to be more accurate than the other voxel-based methods reviewed here, but it is still based upon the same assumptions about the PET images.

Principles of the WM estimation
The mean radioactivity concentration of the WM affects the MG-PVC and A-PVC methods, and therefore it should be estimated as well as possible.An increase in the WM mean value produces decreased values of the PVE-corrected radioactivity concentrations.In the central slices (CS) method for WM estimation, some transaxial slices from the central area of the brain are selected and the WM segments are then eroded in slices to identify the part of the WM region that is not affected by
All three tomographs were operated in the 3D acquisition mode and the images reconstructed with the iterative reconstruction method (OSEM or its variant).All data were dead-time, decay, scatter and attenuation corrected with scanner-specific procedures.The PET input images for the test-retest tests were scanned with the GE Advance PET tomograph.The crystal sizes for the three tomographs are 4.0 × 8.1 × 30 mm, 6.3 × 4.7 × 30 mm and 2.1 × 2.1 × 10-10 mm (dual layer) respectively.
The corresponding FWHM values in the transaxial and axial directions were 5.0 mm and 6.5 mm for the GE Advance, 5.0 mm and 5.8 mm for the PET-CT and 2.5 mm and 2.5 mm for the HRRT tomograph.All FWHM values were acquired according to the NEMA NU-02 standard.[17] Although FWHM degrades when moving out from the center of the field view, in this work it was assumed that the PSF is constant.All radioactivity concentration values were calculated from values measured with a calibration dose calibrator (VDC-404, Veenstra Instrumenten, The Netherlands), the known distribution volume and the time difference between measurement and scan times.

Phantom data
The accuracy of the quantification was tested using a Hoffman brain phantom (model JB003) that resembles a human brain with respect to the distribution of volumes identified as WM, GM and cerebrospinal fluid (CSF) [Figure 1] The phantom consists of 40 plastic plates of 3 mm thickness, where the GM areas are fully excavated and the WM areas are formed so that they have empty spaces of one-fourth of the plate thickness.The phantom was filled with For HRRT, the central 100 planes were used in order to reduce computational requirements.With HRRT, 3.0 mm Gaussian post-smoothing was applied in order to avoid the influence of the structure of the Hoffman phantom.The voxel sizes for the tomographs were 1.17 × 1.17 × 4.25 mm, 1.82 × 1.82 × 3.27 mm and 1.22 × 1.22 × 1.22 mm respectively.
To obtain structural information for the phantom studies, a CT image with 512 × 512 × 47 voxels of size 0.59 × 0.59 × 3.27 mm was used [Figure 1].The usage of a CT image instead of MRI was not expected to produce differences in results, since only the segmentation information is used from these images.Because no mathematical model of the phantom was available, the CT image was segmented to WM and GM regions by first preprocessing it with a median filter and then thresholding it by manually determined low and high threshold values.The resulting CT segment images were already in alignment with the PET-CT PET image, so it was only necessary to re-slice them into the PET image voxel dimensions to give a structural definition of the WM and GM regions.The phantom PET images of the GE Advance and HRRT tomographs were naturally not in alignment with the CT image.These two PET images were co-registered to the PET-CT orientation in order to preserve the segmentation accuracy, which has been reported to be one of the main error factors in PVC with the methods under evaluation.[11] In co-registration, the SPM2 co-registration was used with normalized mutual information (NMI) as a cost function.In the re-slice operation for the PET images, the linear interpolation method was used to calculate the PET image voxel values in the new coordinates.As the bio-distribution is the same and there is no motion during scans, the resulting alignments between CT and PET images were assumed to be uniform.

Test-retest data
To assess the impact of different PVC approaches on the radioactivity estimates and reproducibility and reliability of [ The MR images were segmented by using the segmentation module of the SPM2 software package, which uses a priori probability maps of the GM and WM regions in order to assign voxels in brain space to these segments.The PET images were realigned as previously described, [18] except that SPM2 routines were applied.The ROIs were manually delineated on MR images co-registered to summated PET images using the normalized mutual information method as implemented in SPM2.
ROIs were drawn on axial slices on caudate, putamen, lateral and medial thalamus and cerebellum.All ROIs were created using the Imadeus software (version 1.2, Forima Inc., Turku, Finland).The Simplified Reference Tissue Model (SRTM) [19] using the cerebellum as a reference region was applied to the regional where BSMS is the between-subject mean square of the BP values, WSMS is the within-subject mean square and n is the number of repeated observations (in this case, n = 2).ICC values can range between −1 and 1; values close to 1 indicate that most variance is due to between-subject rather than within-subject variation (good reliability), whereas values below zero imply greater within-subject than between-subject variation (poor reliability).
The mean BP values between test-retest data over eight subjects were compared with t-test (p < 0.05, df = 7) with noncorrected data and with each of the four evaluated PVC methods.Also, the mean BP values over all 16 studies and the mean variability over eight subjects of noncorrected data were tested to the corresponding values of the four PVC approaches with t-test (p < 0.05, df = 15 and p < 0.05, df = 7 respectively).All the t-tests were paired and the t-values were compared to two-tailed t-distribution critical values.

Noise amplification
It is a trivial finding that the corrected voxel values of a PET image increase rapidly when the divider approaches zero in formulae (2-4), (2)(3)(4)(5)(6), (2)(3)(4)(5)(6)(7)(8)(9).The division by the convoluted mask image is done in M-PVC, MG-PVC and A-PVC, and the effect is largest at the edges of the target region.In the center of the region, the divisor is 1 because all radioactivity is supposed to come only from the same region even after smoothing with the PSF.This phenomenon explains the differences in noise amplification between M-PVC, MG-PVC and A-PVC.The M-PVC method amplifies noise at the edges of the conjunction of the GM and WM regions, whereas MG-PVC and A-PVC also amplify noise in the border area between the GM and WM.This effect is clearly visible in Figure 1 when comparing MG-PVC and M-PVC.
Since in the reproducibility tests, all the defined regions were located near the border area of WM and GM, the noise amplification has a considerable effect on all these regions for MG-PVC and A-PVC.This is clearly observable in the medial thalamus region, where only M-PVC gave satisfactory results.The thalamus area seems to be, in general, difficult to segment, and this may have increased the variability of the results in this region.Noise amplification due to PVC need not be problematic when considering the mean radioactivity values in a single scanning session.
However, the effect might be noticeable if further voxel-based analyses are performed.For MG-PVC, the noise amplification was approximately of the same magnitude as for M-PVC when applied to all three tomographs.In addition, MG-PVC had good radioactivity value restoration, which suggests that this method might be a good candidate for further voxel-based analyses in single-scan studies.

Accuracy of ROI mean values
For PET studies in which each subject is scanned only once, it can be more important to have accurate radioactivity values than to have additional reliability in the studies when the interest is in actual value magnitudes rather than in changes between conditions of multiple scans.In the phantom tests of the present study, the true mean radioactivity magnitude restoration was smaller with M-PVC than with the other three methods.Moreover, the t-test between the mean BP values in the caudate and lateral thalamus regions with M-PVC did not indicate significant difference from noncorrected BP values.We therefore draw the following conclusions for A-PVC, R-PVC and MG-PVC: A-PVC produced the best mean radioactivity restoration; hence this method could be used when one is looking for PVE-corrected mean radioactivity values without further voxel-based image analysis or reproducibility.
R-PVC gave weaker radioactivity restoration than A-PVC for the phantom.With the GE Advance PET, it was seen to produce uniform ICC values between the studied regions.This method could be useful when only the mean radioactivity value of the region is used and both radioactivity value restoration and reproducibility are needed.
MG-PVC could be considered a compromise between A-PVC, which is quantitatively accurate; and M-PVC, which better preserves the voxel characteristics in ROIs.MG-PVC is robust to errors in WM estimation, so either R-WME or A-WME could be used as its WM estimator.
Important issues in the calculation of the ROI mean value by A-PVC or MG-PVC are the volume of ROI and its vicinity to the GM border.The former affects the mean sensitivity; and the latter, the increases in local radioactivity variation due to the noise amplification in PVC.Because ROIs often tend to lie at the border of GM, this becomes an issue.On the other hand, when ROIs contain voxels from WM, the estimation of the radioactivity values of WM voxels may crucially affect the usableness of A-PVC and MG-PVC.In order to include the WM voxels in an ROI, the estimated WM mean value may be used as corrected values of the WM voxels.Another alternative is to exclude the noncorrected voxels of ROIs when the number of remaining voxels is reasonable, as was the case in the present study.In contrast, the R-PVC method does not suffer from such a weakness.The M-PVC method solves the issue by not using the border between GM and WM.

Intra-class correlation
Not only the capability of restoring the mean radioactivity values in ROIs but also the reproducibility and reliability are essential properties of PET.Its role should be underlined in studies where the same subject is scanned multiple times.Then, if all true PVE were corrected by a PVC method, the ICC values would be at least the same as without correction.If the BP values remain the same with correction as without it, PVC naturally has no effect on ICC values and the observed variance between scans is due to other factors, such as biological variability.
When ICC values decrease as a result of PVC, the reason might be that the correction has added additional variability between the scans.On the basis of the results of the test-retest experiment [Table 2], M-PVC is more robust as regards the ICC values; the region of the medial thalamus posed a challenge to all other PVC methods.
When the image intensity values approach some constant value, the characteristic numbers of the reproducibility test automatically approach their optimal values (std and variability tend toward zero and ICC toward 100%).Because of this, quantification tests should be carried out in conjunction with the reproducibility test.From the phantom test [Table 1], it was observed that the M-PVC method overestimates the radioactivity in the WM region and this can affect the ICC values of the thalamus regions.However, the effect is expected to be small, especially for the medial thalamus since it is located mainly in the GM region.Therefore, on the basis of the experiment, we conclude that the M-PVC method is the preferred choice for real human studies in which individual subjects are scanned repeatedly.This conclusion, however, includes the assumption that less radioactivity value restoration is acceptable.

Conclusion
Four PVC methods (M-PVC, MG-PVC, R-PVC, A-PVC) and three WM estimation methods (CS, A-WME, R-WME) were tested in order to evaluate their performance in studies of WM/GM radioactivity measurements.The methods were tested with the Hoffman phantom for three PET tomographs (GE Advance, GE DSTE and Siemens HRRT), to address the performance of the methods with tomographs of different features.Of these, the tomograph resolution can be considered as the factor with the greatest consequence on the magnitude of partial volume effects.The correction methods were also tested with test-retest data taken from two different scans of eight subjects, totaling 16 PET images.Variability and ICC values were calculated from the binding potential values of the test-retest sets with and without PVC.Our main observation was that the sophisticated A-PVC method most improved the PET accuracy, which is useful when activity values of ROIs are compared between study groups.Although M-PVC had weaker single-study accuracy, it improved or maintained tomograph reliability even in regions where other methods failed (caudate, putamen, medial thalamus).This property is beneficial in test-retest study designs such as drug-effect studies.The choice between these two methods should finally be made on the basis of the research question of the study.

Figures and Tables
Hoffman phantom: CT image of the CT-PET tomography.A transaxial slice on the left and a sagittal slice on the right.
Evaluation of partial volume effect correction methods for brain positron emission tomography... http://www.ncbi.nlm.nih.gov/pmc/articles/PMC3000501/?report=printable al., Rousset et al., Müller-Gärtner et al. and Meltzer et al.In total, eight methods were evaluated, as three different WM radioactivity estimation methods proposed by Alfano et al., Rousset et al. and Müller-Gärtner et al. were combined with the methods by Alfano et al. and Müller-Gärtner et al.In addition, the binding potential values with eight patients scanned on two separate occasions with the dopamine D2 receptor ligand [ Here I PET,obs stands for the radioactivity values of the acquired image including PVE and noise, I PET,true is the true radioactivity of the object and I PSF is a PSF kernel.
calculate the corrected mean radioactivity values of certain ROIs and voxel-based correction methods that produce corrected image data.The region-based method originally proposed by Rousset et al. (called R-PVC in this paper) divides the image into segments, for which the corrected mean values are calculated by solving a system of linear equations.The voxel-based methods by Meltzer et al., Müller-Gärtner et al. and Alfano et al. (referred to as M-PVC, MG-PVC and A-PVC respectively in this paper) create a simulated image of the radioactivity distribution after the modeled PVE.

j
(j = 1, …, N) for the selected ROIs are modeled by a set of linear equations: where I PET obs, ROI N is the observed mean radioactivity of the N th ROI.This radioactivity is described as a sum which includes the true mean values of all ROIs multiplied by the radioactivity distribution functions RSF.The distribution functions are defined as ROI binary mask images convoluted by the PSF of a particular tomograph (X ROI N I PSF ).The observed mean radioactivity concentration in the ROIs is therefore obtained as a sum of the contributions of all defined ROIs to the current ROI area.In the above set of equations, all RSFs and the observed values are known, which makes it possible to calculate the true mean radioactivity values I N .Furthermore, the values are assumed to be homogenous inside the selected ROIs.Voxel based methods: M-PVC, MG-PVC and A-PVC The voxel-based methods that are evaluated here are based upon a set of assumptions about the PET image under study.In M-PVC, the observed PET image radioactivity concentration I PET obs is formulated as: where X GM + WM refers to a binary mask of the WM and GM segments as determined from an MRI image.The segments are convoluted by the tomograph point spread function I PSF.
PET obs is modeled as a sum of the true GM and WM radioactivity distributions: where C WM is the estimated mean of the WM radioactivity concentration, X WM and X GM are binary masks of the WM and GM segments acquired from the corresponding MRI image and I PSF is the tomograph PSF.In this method, the correction specializes to the GM area and the corrected mean WM radioactivity concentration is used as a starting point for the algorithm.The A-PVC method models the observed intensity I PET obs (p) of point p by the formula:The integration is performed over the affecting region (volume) to p; C(s) is the true radioactivity concentration at point s and g(p, s) is the probability that s contributes to the radioactivity of p.Here g(p, s) can be acquired from the tomograph PSF as in M-PVC and MG-PVC.For points in the GM area, the formula becomes: where which gives the probability that the radioactivity at point p originates from point s.In (2-8) the observed GM radioactivity is obtained by first subtracting WM radioactivity from the PET image, as in MG-PVC.The assumption about the mean value of WM is the same as with MG-PVC.An essential difference from MG-PVC is that the corrected value of each point p is calculated using the observed values from the affecting region (see formulae(2)(3)(4)(5)(6)(7)(8) and (2-9)) and not only from a single point as in MG-PVC (see formula(2)(3)(4)(5)(6)).
Evaluation of partial volume effect correction methods for brain positron emission tomography... http://www.ncbi.nlm.nih.gov/pmc/articles/PMC3000501/?report=printable spillover from the GM.Another way of doing the estimation is to use the method of Rousset et al., reviewed above (referred to as R-WME).Third, in the method proposed by Alfano et al.[3] (referred to as A-WME), an image calculated from convoluted mask images with the formula (X the locations where the values of the image are high, the PET radioactivity values contain little of the true radioactivity from the WM region.Conversely, low values in the image indicate that PET radioactivity values in these locations consist mainly of the true radioactivity from the WM region.In A-WME, the PET radioactivity values are projected against the convoluted mask image.A regression line is then fitted to characterize PET radioactivity values and the probabilities that the radioactivity value originates from the WM region.Finally, the WM estimation is made from an interception of this line.

11 C
] raclopride binding in the human brain, we re-analyzed a previously published data set[18].In brief, eight healthy volunteers had undergone two successive scans with a GE Advance PET tomograph during the same day, at least 2 h apart.All subjects had also undergone 1.5T MR imaging.The image dimensions were 128 × 128 × 35 voxels for the PET and 256 × 256 × 100 voxels for the MRI.Voxel sizes for the PET and the MRI were 2.34 × 2.34 × 4.25 mm and 1.09 × 1.09 × 1.00 mm respectively.
time-radioactivity curves to yield binding potential (BP) values in the ROIs, indicating the capacities of receptors to bind the used ligand [ 11 C] raclopride.The cerebellum reference region was delineated on an area that was defined as the GM region.Test-retest reproducibility and reliability of the BP values were assessed using test-retest variability (VAR) and intra-class correlation coefficients (ICC): where scan1 and scan2 refer to BP values of ROI in test and retest scans, and

Figure 2
Figure 2 Distribution of the standard deviation in a PET image before and after PVC (Bq/ml).Standard deviation images from left or right: noncorrected image, Alfano et al., Müller-Gärtner et al., Meltzer et al.WM estimation by Rousset et al. was used in correction of the two methods in the middle.

Table 1
Results of partial volume effect correction for a Hoffman phantom

Table 2
Effect of the positron emission tomography PVC methods on binding potential estimated by simplified reference tissue model for different brain regionsThe test set consisted of eight subjects.Each subject was scanned twice.Mean = Mean value of BP over all 16 scans; VAR = Mean variability between two scans over eight subjects; t-value = t value between the mean values of test and retest scans (df = 7, critical value = 2.306 with P < 0.05); ICC = Mean intraclass correlation value between scabs over eight subjects.Alfano et al., and Müller-Gärtner methods were used with WM estimation method by Alfano et al. as no difference was seen between WM corrections.Articles from Journal of Medical Physics / Association of Medical Physicists of India are provided here courtesy ofMedknow Publications