Influence of Thrice-Induction-Heating and Once-Quenching on Fatigue Strength of SAE52100 Steel

Koshiro Mizobe; Hitonobu Koike; Katsuyuki Kida

doi:10.4028/www.scientific.net/AMR.893.415

Paper Titles

Corrosion Behavior of Austenitic Stainless Steel in High Sulphate Content
p.397

Mechanical Properties and Microstructures of Al-12Zn-2.4Mg-1.2Cu Alloy Extruded Sheet
p.402

Effect of Tempering Temperature on Mechanical Properties and Microstructures of 800MPa Microalloy Low Carbon Bainitic Steel
p.406

Influences of H₂SO₄ and NaCl Concentrations on Stress Corrosion Cracking of AISI 304 Stainless Steel
p.410

Influence of Thrice-Induction-Heating and Once-Quenching on Fatigue Strength of SAE52100 Steel
p.415

The Static Recrystallization Behavior of Fe-Mn-Si-Al Series TWIP Steel
p.419

Microstructure and Plastic Deformation Behavior of Modified AA7075-T6 Aluminum Alloy
p.424

Wear and Frictional Behaviour of Metals
p.430

An Evaluation of the Fire Performance of H-Section Made of Ordinary Strength Structural Steels by Differences of Length
p.436

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 893Influence of Thrice-Induction-Heating and...

Influence of Thrice-Induction-Heating and Once-Quenching on Fatigue Strength of SAE52100 Steel

Abstract:

Martensitic high-carbon high-strength SAE 52100 bearing steel is one of the main alloys used as the principal alloys for rolling contact applications. We developed a novel repeated quenching method by induction heating in order to enhance the materials strength. The steel bar passed through the heated coil several times and finally quenched by cooling water. The rotating bending fatigue tests was done in order to investigate the fatigue strength of the steel bars. The heat affected zone (HAZ) was not expanded by the heat treatment however it was found that the thrice-induction-heating and once-quenching improved the fatigue strength. These two features indicated that the size of heat affected zone does not dominate the strength of heated-samples.

You might also be interested in these eBooks

Advanced Materials and Engineering Materials III

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 893)

Pages:

415-418

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.893.415

Citation:

Cite this paper

Online since:

February 2014

Authors:

Koshiro Mizobe, Hitonobu Koike, Katsuyuki Kida*

Keywords:

Fatigue Strength, Induction Heating, Repeated Heating, SAE 52100

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

* - Corresponding Author

References

[1] 1. Janez Grum, A review of influence of grinding conditions on resulting residual stresses after induction surface hardening and grinding, Journal of Materials Processing Technology, 2001, Vol. 114, pp.212-226.

DOI: 10.1016/s0924-0136(01)00562-3

Google Scholar

[2] R. A. Grange, The Rapid Heat Treatment of Steel, Metallurgical Transactions, 1971, Vol. 2, pp.65-78.

Google Scholar

[3] R. A. Grange and E. R. Shackelford, Method of Producing Ultrafine Grained Steel, 1963, US patent 3, 178, 324.

Google Scholar

[4] R. A. Grange and E. R. Shackelford, Method of Producing Fine Grained Steel, 1966, US patent 3, 278, 345.

Google Scholar

[5] R. A. Grange, Effect of microstructural banding in steel, Metallurgical and Materials Trans. A, 1971, Vol. 2, pp.417-426.

DOI: 10.1007/bf02663328

Google Scholar

[6] H. J. Kim, Y. H. Kim and J. W. Morris, Jr., Thermal mechanisms of grain and packet refinement in a lath, ISIJ International, 1998, Vol. 38, No. 11, pp.1277-1285.

DOI: 10.2355/isijinternational.38.1277

Google Scholar

[7] . K. Kawasaki and T. Yamazaki, Grain refining of steel by induction heat-treating (2) –Mechanism of refining and related studies-, Netsusyori, 2006, Vol. 46, No. 3, pp.123-130, in Japanese.

Google Scholar

[8] E. S. Kayali, H. Sunada, T. Oyama, J. Wadsworth and O. D. Sherby, The development of fine structure superplasticity in cast ultrahigh carbon steels through thermal cycling, Journal of materials science, 1979, Vol. 14, No. 11, pp.2688-2692.

DOI: 10.1007/bf00610640

Google Scholar

[9] H. Sakai, S. Ochiai and M. Ueno, Fine Structures and Mechanical Properties of Thermally Cycled SUJ 2 Steel, Tetsu- to- Hagane The Iron and Steel Institute of Japan, 1989, Vol. 75, No. 4, pp.657-664, in Japanese.

DOI: 10.2355/tetsutohagane1955.75.4_657

Google Scholar

[10] C, Ooki, K. Maeda and H. Nakashima, Improving rolling contact fatigue life of bearing steels through grain refinement, 2004, NTN technical review, Vol. 71, pp.2-7.

DOI: 10.4271/2004-01-0634

Google Scholar

[11] H. Koike, E. C. Santos, K. Kida, T. Honda and J. Rozwadowska, Effect of Repeated Induction Heating on Fatigue Crack Propagation in SAE 52100 Bearing Steel, Advanced Material Research, 2011, Vol. 217-218, pp.1266-1271.

DOI: 10.4028/www.scientific.net/amr.217-218.1266

Google Scholar

[12] E. C. Santos, K. Kida, T. Honda, J. Rozwadowska, K. Houri and K. Hashimoto, Influence of Cyclic Heat Treatment and Oxygen Content on the Rolling Contact Fatigue of JIS SUJ2 Bearings, Advanced Material Research, 2011, Vol. 217-218, pp.982-987.

DOI: 10.4028/www.scientific.net/amr.217-218.982

Google Scholar

[13] M. Koga, E. C. Santos, T. Honda, K. Kida and T. Shibukawa, Investigation of wear in induction–heated AISI E 52100 steel bars under reciprocating motion, International Journal of Materials and Product Technology, 2012, Vol. 44, No. 3/4, pp.240-251.

DOI: 10.1504/ijmpt.2012.050185

Google Scholar