Distribution & Access For Publication Downloads News About Us Contact Us
Paper Titles
Research and Development of Inconel 718 Type Superalloy
p.262
Deformation Mechanisms of Nanocrystalline Materials
p.270
Solute and Second Phase Evolution during Industrial Processing of AA3103
p.281
Application of Local Tomography Technique to High-Resolution Synchrotron X-Ray Imaging
p.287
Change of Young's Modulus of Cold-Deformed Aluminum AA 1050 and of AA 2024 (T65): A Comparative Study
p.293
The Effect of Chemistry and Cooling Rate on the Latent Heat Released during the Solidification of the 3XX Series of Aluminum Alloys
p.299
Behavior of Hydrogen in Al-4%Mg Alloys during Heat Treatment
p.305
Phase Transformation for Primary Particles in the Surface Regions of an AA1200 Alloy
p.311
Tailoring the Mechanical Properties of Al-Sn-Alloys for Tribological Applications
p.317

Change of Young's Modulus of Cold-Deformed Aluminum AA 1050 and of AA 2024 (T65): A Comparative Study

Article Preview

Abstract:

The knowledge of some mechanical properties of materials and their changes with thermal treatments and/or mechanical treatments are essential to obtain the best results during simulation of processes. In this paper, changes of Young's modulus at room temperature of colddeformed aluminum AA1050 carried out in a tension machine and changes of Young’s modulus and Poisson’s ratio of AA2024 (T6 and T65) have been determined. The elastics constants have been measured by the ultrasound technique in AA2024 alloy and by tensile test in AA1050. In this alloy, the Young's modulus (E) diminishes during the first step of deformation and then increases with the successive cold working. Changes in Young's modulus measured are around 6-8%. In AA2024, the Young's modulus change is about 3% between the annealed and quenched alloy (minimum value); during aging the E parameter increases with respect to quenching. These changes are correlated with the structural changes during thermal treatments. In AA2024, the E parameter remains almost constant during cold-working after the aging treatment. Poisson’s ratio of this alloy remains almost constant in all the treatments. These results are also correlated with the dislocations arrangement in both materials. This behaviour is also compared with cold-deformed pure iron in a tensile test. These results confirm that aluminum AA1050 present similar behaviour than it was observed for pure iron.

You might also be interested in these eBooks
THERMEC 2006 View Preview

Info:

Periodical:

Materials Science Forum (Volumes 539-543)

Pages:

293-298

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.539-543.293

Citation:

Cite this paper

Online since:

March 2007

Authors:

A. Villuendas, Antoni Roca, Jordi Jorba

Keywords:

Aging, Aluminium Alloy, Cold Working, Young's Modulus

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] D.J. Mack: Trans. AIME Vol. 166 (1946), p.68.

Google Scholar

[2] J.A. Benito, J.M. Manero, J. Jorba and A. Roca: Met. and Mat. Trans. A Vol. 36A (2005), p.3317.

Google Scholar

[3] H.M. Ledbetter, S.A. Kim: Mater. Sci. Eng. A Vol. 101 (1988) p.87.

Google Scholar

[4] F. Morestin and M. Boivin: Nuclear Eng. and Design Vol. 162 (1996), p.107.

Google Scholar

[5] K. Yamaguchi, H. Adachi and N. Takakura: Met. and Mat. Vol. 4, 3 (1998) p.420.

Google Scholar

[6] J.A. Benito, J. Jorba and A. Roca: Mat. Sci. Forum Vol. 426-432 (2003), p.4435.

Google Scholar

[7] J. Jorba, R. Pons, J.A. Benito and A. Roca: Special Issue J. Mater. Processing Technol. Vol. 117, 3, Thermec'00-Proc. Int. Conf. On Processing and Manufacturing Advanced Materials, Las Vegas, NV, CDROM.

Google Scholar

[8] J.A. Benito: Ph D Thesis, University of Barcelona, Spain, (2001).

Google Scholar

[9] W. Köster and K. Rosenthal: Zisch. Metallkunde Vol. 30 (1938), p.345.

Google Scholar

[10] S. Shima and M. Yang: J. Soc. Mat. Sci. Japan Vol. 44, 500 (1995) p.578.

Google Scholar

[11] E.P. Papadakis: J. Appl. Phys. Vol. 35 (1964) p.1474.

Google Scholar

[12] Smithells Metals Reference Book, 7 th. Ed., E.A. Brandes, G.B. Brook (Ed. ) 1992, p.15. 2.

Google Scholar

[13] I. Fonseca, J.A. Benito, I. Mejía, J. Jorba and A. Roca: Rev. Metal. Madrid Vol. 38 (2002), p.249.

Google Scholar

[14] E.P. Papadakis, C.A. Stickels and R.C. Innes: SAE Trans. JNL Mats. Manufac. Vol. 104 (1995), p.830.

Google Scholar

[15] M. Lucena, J.A. Benito, A. Roca and J. Jorba: Rev. Metal. Madrid Vol. 34 (1998), p.310.

Google Scholar

[16] J. Calle, J.A. Benito, J. Jorba and A. Roca: Proc. V Congreso Nacional de Propiedades Mecánicas de Sólidos UPC Vol. 1 (1996), p.314.

Google Scholar

[17] N.F. Mott: Phil. Mag. Vol 43 (1952), p.1151.

Google Scholar

[18] J. Friedel: Phil. Mag. Vol. 44 (1953), p.444.

Google Scholar

Scientific.Net is a registered brand of Trans Tech Publications Ltd
© 2024 by Trans Tech Publications Ltd. All Rights Reserved