风向自适应型涡激振动压电俘能器的试验研究

doi:10.3901/JME.2022.20.120

机械工程学报 ›› 2022, Vol. 58 ›› Issue (20): 120-127.doi: 10.3901/JME.2022.20.120

• 特邀专栏：振动俘能器件与系统 • 上一篇下一篇

扫码分享

风向自适应型涡激振动压电俘能器的试验研究

侯成伟¹, 单小彪¹, 宋汝君², 谢涛¹

1. 哈尔滨工业大学机器人技术与系统国家重点实验室哈尔滨 150001;
2. 山东理工大学机械工程学院淄博 255049

收稿日期:2022-03-23 修回日期:2022-08-29 出版日期:2022-10-20 发布日期:2022-12-27
通讯作者: 单小彪(通信作者)，男，1977年出生，博士，副教授，博士研究生导师。主要研究方向俘能技术、抑振技术、超声波振动拉丝技术、超声波振动减阻技术、航空航天仿真装备。E-mail：shanxiaobiao@hit.edu.cn
作者简介:侯成伟，男，1992年出生，博士研究生。主要研究方向为;振动俘能。E-mail：hcwking@163.com
基金资助:
国家自然科学基金资助项目(51875116，51705296)。

Experimental Study of Orientation Adaptive Piezoelectric Energy Harvester Based on Vortex Induced Vibration

HOU Chengwei¹, SHAN Xiaobiao¹, SONG Rujun², XIE Tao¹

1. State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin 150001;
2. School of Mechanical Engineering, Shandong University of Technology, Zibo 255049

Received:2022-03-23 Revised:2022-08-29 Online:2022-10-20 Published:2022-12-27

摘要/Abstract

摘要： 风能在自然界中是一种储量丰富、可持续利用的清洁能源。利用压电俘能器将风能转换为电能代替传统化学电池为低功耗电子设备持续供电已经获得了国内外学术和工业领域的认可。针对自然环境中风场的风向和速度时变特点，提出一种新颖的风向自适应型涡激振动压电俘能器。本俘能器可以根据风向的变化，自主调节迎风角度，从而使得俘能器能够在不同方向来风激励时拥有良好的输出性能。其主要由两个L型压电俘能梁、轴承底座、旋转固定座、导向翼等部分组成。通过搭建的小型风洞测试系统，对俘能器样机进行了测试和分析：受不同方向来风激励时，俘能器的输出功率绝对积分面积的平均相对偏差不大于6.1%；俘能器的风向自适应开启状态相对关闭状态，两个压电俘能梁的输出功率绝对积分面积平均值分别提升了468.2%和492.3%。自适应型压电俘能器的研究结果对提高俘能器的环境适应能力和增强输出性能有良好的参考价值。

关键词: 自适应, 涡激振动, 压电, 俘能, 风能

Abstract: Wind energy is a kind of clean energy with rich reserves and sustainable utilization in nature. It has been recognized in domestic and foreign academic and industrial fields that piezoelectric energy harvester(PEH) can take place traditional chemical battery to continuously supply power for low-power electronic equipment. For overcoming the time-varying characteristics of wind direction and velocity in nature, a novel orientation adaptive piezoelectric energy harvester based on vortex-induced vibration is proposed. The energy harvester can autonomously adjust the windward angle according to the change of wind direction. It mainly composes two L-shaped parts (EH1, EH2), bearing base, rotating fixed seat, and guide wing. And the prototype of the energy harvester is tested and analyzed: when excited by wind from different directions, γ is no more than 6.1%; Comparing close state of orientation adaptive, S_AVG of open state is increased by 468.2% and 492.3% for EH1 and EH2 respectively. The results of the proposed orientation adaptive PEH have a good reference value for improving the environmental adaptability and output performance of harvesters.

Key words: orientation adaptive, vortex-induced vibration, piezoelectricity, energy harvesting, wind energy

中图分类号:

TM619

侯成伟, 单小彪, 宋汝君, 谢涛. 风向自适应型涡激振动压电俘能器的试验研究[J]. 机械工程学报, 2022, 58(20): 120-127.

HOU Chengwei, SHAN Xiaobiao, SONG Rujun, XIE Tao. Experimental Study of Orientation Adaptive Piezoelectric Energy Harvester Based on Vortex Induced Vibration[J]. Journal of Mechanical Engineering, 2022, 58(20): 120-127.

参考文献

[1] PEARRE N，SWAN L. Combining wind，solar，and in-stream tidal electricity generation with energy storage using a load-perturbation control strategy[J]. Energy，2020，203:117898-1179010.
[2] TIAN X，MEYER T，LEE H.. et al. Sustainable design of geothermal energy systems for electric power generation using life cycle optimization[J]. AIChE Journal，2019，66 (4):1-18.
[3] CHEN S，EAGER D，ZHAO L. Enhanced frequency synchronization for concurrent aeroelastic and base vibratory energy harvesting using a softening nonlinear galloping energy harvester[J]. Journal of Intelligent Material Systems and Structures，2021，33 (5):1-16.
[4] 王淑云，朱雅娜，阚君武，等. 旋磁激励式预弯梁压电俘能器建模仿真与试验[J]. 机械工程学报，2020，56 (14):224-230. WANG Shuyun，ZHU Yana，KAN Junwu，et al. Prebending-cantilever piezo-harvester excited by rotary magnet[J]. Journal of Mechanical Engineering，2020，56 (14):224-230.
[5] XIE X，ZHANG J，WANG Z，et al. An experimental study on a high-efficient multifunctional U-shaped piezoelectric coupled beam[J]. Energy Conversion and Management，2020，224:113330-113344.
[6] ZHAO L，YANG Y. An impact-based broadband aeroelastic energy harvester for concurrent wind and base vibration energy harvesting[J]. Applied Energy，2018，212:233-243.
[7] GU Y，LIU W，ZHAO C，et al. A goblet-like non-linear electromagnetic generator for planar multi-directional vibration energy harvesting[J]. Applied Energy，2020，266:114846-114864.
[8] FAN K，LIU J，WEI D，et al. A cantilever-plucked and vibration-driven rotational energy harvester with high electric outputs[J]. Energy Conversion and Management，2021，244:114504-114516.
[9] FAN K，WANG C，CHEN C，et al. A pendulum-plucked rotor for efficient exploitation of ultralow-frequency mechanical energy[J]. Renewable Energy，2021，179:339-350.
[10] GUO X，ZHANG Y，FAN K，et al. A comprehensive study of non-linear air damping and “pull-in” effects on the electrostatic energy harvesters[J]. Energy Conversion and Management，2020，203:112264-112276.
[11] ZHANG Y，WANG T，LUO A，et al. Micro electrostatic energy harvester with both broad bandwidth and high normalized power density[J]. Applied Energy，2018，212:362-371.
[12] ZHANG Y，WANG T，ZHANG A，et al. Electrostatic energy harvesting device with dual resonant structure for wideband random vibration sources at low frequency[J]. The Review of Scientific Instruments，2016，87(12):125001-125009.
[13] TAO K，YI H，YANG Y，et al. Miura-origami-inspired electret/triboelectric power generator for wearable energy harvesting with water-proof capability[J]. Microsyst Nanoeng，2020，6(56):1-11.
[14] ZHAO C，YANG Y，UPADRASHTA D，et al. Design，modeling and experimental validation of a low-frequency cantilever triboelectric energy harvester[J]. Energy，2021，214:118885-118895.
[15] MA X，ZHOU S. A review of flow-induced vibration energy harvesters[J]. Energy Conversion and Management，2022，254:115223-115249.
[16] WANG J，HU G，SU Z，et al. A cross-coupled dual-beam for multi-directional energy harvesting from vortex induced vibrations[J]. Smart Materials and Structures，2019，28 (12):1-10.
[17] NASEER R，DAI H L，ABDELKEFI A，et al. Piezomagnetoelastic energy harvesting from vortex-induced vibrations using monostable characteristics[J]. Applied Energy，2017，203:142-153.
[18] DAI H L，ABDELKEFI A，YANG Y，et al. Orientation of bluff body for designing efficient energy harvesters from vortex-induced vibrations[J]. Applied Physics Letters，2016，108 (5):053902-053907.
[19] TAN T，HU X，YAN Z，et al. Enhanced low-velocity wind energy harvesting from transverse galloping with super capacitor[J]. Energy，2019，187:115915-115928.
[20] HU G，WANG J，SU Z，et al. Performance evaluation of twin piezoelectric wind energy harvesters under mutual interference[J]. Applied Physics Letters，2019，115 (7):073901-073905.
[21] HU G，WANG J，TANG L. A comb-like beam based piezoelectric system for galloping energy harvesting[J]. Mechanical Systems and Signal Processing，2021，150:107301-107322.
[22] 田海港，单小彪，张居彬，等. 翼型颤振压电俘能器的输出特性研究[J]. 力学学报，2019，51(4):1148-1155. TIAN Haigang，SHAN Xiaobiao，ZHANG Jubin，et al. Output characteristics investigation of airfoil-based flutter piezoelectric energy harvester[J]. Chinese Journal of Theoretical and Applied Mechanics，2019，51(4):1148-1155.
[23] LI K，YANG Z，GU Y，et al. Nonlinear magnetic-coupled flutter-based aeroelastic energy harvester:Modeling，simulation and experimental verification[J]. Smart Materials and Structures，2019，28 (1):015020-015035.
[24] LI Z，ZHOU S，YANG Z. Recent progress on flutter-based wind energy harvesting[J]. International Journal of Mechanical System Dynamics，2022，2 (1):82-98.
[25] FANG S，ZHOU S，YURCHENKO D，et al. Multistability phenomenon in signal processing，energy harvesting，composite structures，and metamaterials:A review[J]. Mechanical Systems and Signal Processing，2022，166:108419-10480.
[26] WANG J，GENG L，ZHOU S，et al. Design，modeling and experiments of broadband tristable galloping piezoelectric energy harvester[J]. Acta Mechanica Sinica，2020，36:592-605.
[27] YANG K，QIU T，WANG J，et al. Magnet-induced monostable nonlinearity for improving the VIV-galloping-coupled wind energy harvesting using combined cross-sectioned bluff body[J]. Smart Materials and Structures，2020，29 (7):1-12.
[28] LI K，YANG Z，ZHOU S. Performance enhancement for a magnetic-coupled bi-stable flutter-based energy harvester[J]. Smart Materials and Structures，2020，29:085045-085062.
[29] ZHANG L B，DAI H L，ABDELKEFI A，et al. Theoretical modeling，wind tunnel measurements，and realistic environment testing of galloping-based electromagnetic energy harvesters[J]. Applied Energy，2019，254:113737-113749.
[30] HALIM M A，RANTZ R，ZHANG Q，et al. An electromagnetic rotational energy harvester using sprung eccentric rotor，driven by pseudo-walking motion[J]. Applied Energy，2018，217:66-74.
[31] WU Z，GUO H，DING W，et al. A hybridized triboelectric–electromagnetic water wave energy harvester based on a magnetic sphere[J]. ACS Nano，2019，13:2349-2356.
[32] WANG Y，YANG E，CHEN T，et al. A novel humidity resisting and wind direction adapting flag-type triboelectric nanogenerator for wind energy harvesting and speed sensing[J]. Nano Energy，2020，78:105279-105288.
[33] GONG Y，SHAN X，LUO X，et al. Direction-adaptive energy harvesting with a guide wing under flow-induced oscillations[J]. Energy，2019，187:115983-115990.

风向自适应型涡激振动压电俘能器的试验研究

Experimental Study of Orientation Adaptive Piezoelectric Energy Harvester Based on Vortex Induced Vibration

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	尹帅, 石斌, 孙逸凡, 槐雅萍, 王晶. 轻量化自适应柔性踝关节康复机器人设计与评估[J]. 机械工程学报, 2022, 58(9): 10-20.
[2]	李振, 赵欢, 王辉, 丁汉. 机器人磨抛加工接触稳态自适应力跟踪研究[J]. 机械工程学报, 2022, 58(9): 200-209.
[3]	向红标, 程旭, 李梦伟, 王收军, 张冕, 黄显, 霍文星. 磁弹性微型游泳机器人在外部干扰和复杂路径下的精确跟踪控制[J]. 机械工程学报, 2022, 58(7): 93-102.
[4]	张文鑫, 吕震宙. 一种新的自适应Kriging法停止准则及其在涡轮盘疲劳寿命可靠性中的应用[J]. 机械工程学报, 2022, 58(6): 263-273.
[5]	魏凌涛, 王翔宇, 邱彬, 李亮, 周道林, 林进贵. 基于自适应预瞄路径的自动驾驶车辆寻迹和避障控制[J]. 机械工程学报, 2022, 58(6): 184-193.
[6]	孙朱俊, 许斌, 黄典贵. 前缘涡振圆柱对翼型气动性能的影响[J]. 机械工程学报, 2022, 58(6): 242-252.
[7]	张济民, 宗振海, 周和超, 寇杰. 独立旋转轮对轨道车辆自适应导向控制研究[J]. 机械工程学报, 2022, 58(4): 232-239.
[8]	王淑云, 任泽峰, 阚君武, 杨泽盟, 张忠华, 黄乐帅, 孟凡许. 双磁耦合式压电振动俘能器的性能分析与试验[J]. 机械工程学报, 2022, 58(20): 150-157.
[9]	吴义鹏, 李森, 蓝春波, 周圣鹏, 谢维泰, 裘进浩, 季宏丽. 压电能量俘获结构及其升频转换技术的发展现状[J]. 机械工程学报, 2022, 58(20): 27-45.
[10]	于家豪, 陶凯. 振动俘能技术在可穿戴领域的应用[J]. 机械工程学报, 2022, 58(20): 46-71.
[11]	单小彪, 隋广东, 田海港, 王艺聪, 谢涛. 潜水式尾流激振压电俘能器的输出性能研究[J]. 机械工程学报, 2022, 58(20): 101-110.
[12]	潘巧生, 赵明飞, 李晨, 黄梓良, 陈立蔚, 王雅. 利用偏心转子实现转速与驱动频率一致的高速压电马达研究[J]. 机械工程学报, 2022, 58(15): 233-242.
[13]	卢炽华, 孙孟雷, 刘志恩, 陈弯, 李晓龙. 主动冲击噪声控制自适应算法综述及综合性能分析[J]. 机械工程学报, 2022, 58(13): 101-118.
[14]	陈诚, 皮志勇, 赵英龙, 廖玄, 张明敏, 李勇. 基于自适应灾变遗传-循环神经网络的锂离子电池SOC估计^*[J]. 电气工程学报, 2022, 17(1): 86-94.
[15]	王东伟, 刘明星, 吴霄, 钱韦吉. 压电式摩擦振动能量收集的试验研究与仿真分析[J]. 机械工程学报, 2021, 57(9): 89-98.