Biological Treatment of a Synthetic Musk in a Raw Hospital Wastewater Under Different Sludge Retention Times

Received Date: Dec 19, 2018 / Accepted Date: Jan 18, 2019 / Published Date: Jan 19, 2019 Abstract: Pharmaceuticals and personal care products (PPCPs) are the problem of our age and hospital wastewaters are one of the main sources of PPCPs having a concentration range of ng L to μg L. Hospital wastewaters are almost untreated before being discharged into municipal/urban wastewater treatment plants (WWTPs) via wastewater networks in Turkey. These WWTPs are not designed to remove complex compounds such as PPCPs, however, a sizeable amount is released into the environment. Some of the PPCPs present a considerable threat for aquatic organisms even at very low concentrations. This study presents the biological treatability of a synthetic musk namely musk tonalide (AHMT) from a raw hospital wastewater under different sludge retention times (SRTs). The treatability of this PPCP was investigated using an anaerobic UASB/aerobic CSTR sequential biological reactor system in laboratory conditions for the first time in Turkey. Effect of different sludge retention times (5; 30; 45 and 55 days) on the removal of AHMT was researched at mesophilic temperature conditions for the biological reactors. COD, SCOD and AHMT yields were determined. Methane gas (CH4) productions and VFA concentrations were also monitored in anaerobic UASB reactor. pH changes, dissolved oxygen (DO) variations and redox potentials (ORPs) were monitored in anaerobic UASB and aerobic CSTR reactors. As a result of the study, increasing of the SRT has a positive effect on COD (94.1%) and SCOD (91.1%) yields at 55 days of SRT in the biological reactor system. Also, biodegradation (in the supernatant) and adsorption (onto biological sludge) removal efficiencies of AHMT were increased at higher SRTs. AHMT was removed 42.3% with biodegradation from the supernatant while adsorption removal efficiency reached 57.5% in the biological sludge at 55 days of SRT for the anaerobic UASB/aerobic CSTR sequential biological reactor system.


Introductıon
Micropollutants such as pharmaceuticals and personal care products (PPCPs) in hospital wastewater are directly discharged into the sewage system without treatment since the conventional sewage/urban treatment plants can only remove macropollutants such as BOD5, COD, heavy metals, nitrogen and phosphorus in Turkey. The micropollutants decrease the biological treatment efficiency if they are not treated and then discharged into the receiving environment [1]. AHMT is a pharmaceutical and personal care product (PPCP) and used as a synthetic musk. Synthetic musks are a group of persistent organic chemicals that have been used as fragrances in household products, perfumes and other cosmetic products. Since then many studies have dealt with the environmental distribution of these chemicals and today such compounds have been proven to be present in practically all environmental compartments, including human tissue, close to densely populated areas [2]. Even low concentrations of these musk compounds have been reported to inhibit multixenobiotic resistance mechanisms in mussels, to cause cell typedependent anti-estrogenic effects and to inhibit larval development in marine copepods [3]. The recent studies performed with AHMT contained mostly the detection of its levels in water, sediment [4,5] and the detection methods [6,7] of AHMT. The treatability studies of AHMT is limited with some studies: Santiago-Morales et al. [8], investigated the treatment of AHMT with ozonation with hydrogen peroxide (O3, O3/H2O2), ultraviolet (254 nm low pressure mercury lamp) and xenon-arc visible light irradiation. The best results was 65% removal after 5 min with ozonation and light photocatalytic ozonation (O3/Xe/Ce-TiO2). A significant removal of 79% was obtained for AHMT after 15 min during visible light photocatalysis (O2/Xe/Ce-TiO2). An anaerobic membrane reactor was used to remova tonalide from the aqueous phase of a pharmacy wastewater by a combination of biotransformation and sorption onto the biosolids [9]. Biotransformation of tonalide was observed to be the dominant removal mechanism (87%). Zhang et al., [10], found that the adsorption of AHMT to microplastics is low (34%) while the equilibrium sorption time was about 10 h and the adsorption kinetics model conformed to a Lagergren adsorption mode at 25°C.
The novelty of the study is to treat a synthetic musk namely musk tonalide (AHMT) biologically from a raw hospital wastewater under different sludge retention times (SRTs) for the first time in Turkey. The aim of this study was to evaluate the treatability of this PPCP using an anaerobic UASB/aerobic CSTR sequential biological reactor system in laboratory conditions. Effect of different sludge retention times (5,30,45 and 55 days) on the removal of AHMT was researched at mesophilic temperature conditions for the biological reactors. COD, SCOD and AHMT removal efficiencies were determined. Methane gas (CH4) productions and total volatile fatty acid (TVFA) concentrations were also monitored in anaerobic UASB reactor. Also, dissolved oxygen (DO) variations and redox potentials (ORPs) were monitored in anaerobic UASB and aerobic CSTR reactors.

Source and Characterization of Raw Hospital Wastewater and Biomass
Raw hospital wastewater was taken from Dokuz Eylul University Hospital (Izmir, Turkey) sewer channel. The influent chemical oxygen demand (COD) concentration of the raw hospital wastewater was 912±43 mg L -1 while the influent soluble chemical oxygen demand (SCOD) concentration of the raw hospital wastewater was 822±28 mg L -1 (Data not shown). The influent musk tonalide (AHMT) concentration was 236.00±0.05 µg L -1 (Data not shown). The pH, the temperature, the total nitrogen and total phosphorus concentrations were 8.50±0.02, 18±2°C, 0.40±0.01 and 1.00±0.01 mg L -1 , respectively (Data not shown). Anaerobic and aerobic biomass were taken from Pakmaya Baker's Yeast Factory's (Izmir, Turkey) anaerobic reactor and aeration tank of the biological treatment process, respectively.

Physicochemical Properties of AHMT
The physicochemical properties of micropollutants are important in the prediction of their environmental fate and in the development of analytical detection methods. Based on the calculated log Kow value reported for AHMT, it can be said that AHMT is very hydrophobic. Physicochemical properties of AHMT are given in Table 1. The laboratory-scale aerobic reactor used in this system consists of a continuous flow stirred tank reactor (CSTR) without sludge return and has a total volume of 2.0 L ( Figure  1). The anaerobic reactor is an upflow anaerobic sludge bed reactor (UASB) without sludge return and has a total volume of 2.5 L ( Figure 1). They were equipped with influent, effluent, sampling and gas outlet valves.
Required temperature conditions for the both reactors were provided with infrared heaters. Sequential reactor was defined as the total of anaerobic and aerobic reactor.

Operational Conditions Used in this Study
All the biological reactors were fed with synthetic hospital wastewater for 20 days. After the start-up period, the reactors were filled with raw hospital wastewater for 20 days for each SRT and the effects of SRTs (5, 30, 45 and 55 days) on COD, SCOD, AHMT yields in aerobic and in anaerobic reactors were determined while methane gas productions, TVFA accumulation and the ratio of TVFA to bicarbonate alkalinity were monitored in the anaerobic reactor. Since the sludge was not recycled; the sludge retention time was equal to hydraulic retention time. The SRT was adjusted by discarding of certain amount of sludge by using a formula of SRT=V/Qw in both reactors. V; is the reactor volume while Qw is the wasted sludge according to SRT chosen. The anaerobic and aerobic reactors were operated 20 days during each SRT to reach steady-state conditions. The steady-state conditions were defined with constant effluent pollutant concentrations during 7 executive days.

Procedure for AHMT Measurement in the Raw Hospital Wastewater
Analysis were performed in a gas chromatograph coupled to a quadrupole mass spectrometer, in electron ionization (EI) mode, using a GC-MS (Agilent 7890A) combined with a mass selective detector (Agilent 5975C inert MSD) equipped with a flame ionization detector and an HP-5MS capillary column with a length of 30.0m×0.25mm (I.D.)×0.25μm (film thickness) (Agilent Technologies Inc.). Helium (purity 99.999%) was employed as carrier gas with a constant flow of 1.0 mL min -1 . The standards were injected (2µL) into the GC system in splitless mode, with a splitless time of 1.5 min. The injector, quadrupole, transfer line and ion source were set at 275, 150, 300 and 230°C respectively. The oven program was set at 35 °C for 0 min then 5°C min -1 to 200°C for 0 min then to 20°C min -1 to 285 °C for 5 min. Acquisition was performed by Selected Ion Monitoring (SIM) and the monitored ions were 243 and 258 m/z for AHMT. The retention time was determined as 30.891 min [12]. Aqueous AHMT stock solution was prepared from the AHMT standard (Fluka, 6-Acetyl-1,1,2,4,4,7hexamethyl-tetralin). Calibration curve of AHMT was drawn for 1-5-10-50-100-200 µg L -1 . Correlation coefficient (R 2 ) was obtained as 0.997567 for AHMT. AHMT were extracted from raw hospital wastewater by solid-phase extraction (SPE) method. The OASIS HLB Cartridge was conditioned with 6 mL of 30% MeOH in DCM followed by the addition of 6 mL MeOH. After passing the sample through the cartridge, the cartridge was dried under vacuum for 1 hour. The compounds were eluted with 6 mL of mixture of DCM-hexane (4:1). The eluant was evaporated using Nitrogen evaporator. The dried extract was then dissolved in hexane and the final volume made to 1 mL [13].

Conventional
Pollutants Measurement Methods COD, SCOD, MLSS and MLVSS were measured according to Standard Methods [14]. Total nitrogen and total phosphorus were measured with reagent kits in a Photometer Nova 60/Spectroquant. pH, DO and ORP were measured with WTW probes. Bicarbonate alkalinity and TVFA were measured using the Anderson and Yang method [15]. CH4 gas productions were detected by using a liquid containing 3% NaOH to scrub out the CO2 from the biogas [16].

Calculation of AHMT Adsorption and Volatilization
To determine the adsorption of the micropollutants onto activated sludge, eluates were prepared from activated sludge samples from aerobic and anaerobic reactors. Granular sodium sulfate was burnt at 450 °C for 2 hours firstly, and then it was desiccatored for 1 hour. The burnt sodium sulfate was added to the activated sludge sample to the dewatering process. Methanol was added to the dewatered sludge samples and the eluate was strirred for 24 hours on magnetic stirrers. The eluate was filtered first 0.45 µm cellulose acetate membrane filter (Sartorius Stedim Biotech) and then filtered through 0.45 µm PVDF membrane filter (Pall Corporation). The eluates were extracted according to the aforementioned SPE method and then, they were measured in GC-MS. For the determination of AHMT volatilization polyurethane foam (PUF) disks were used both for anaerobic and aerobic reactors. PUF disks were placed the headspace of each reactor and the reactors were placed in a closed glass system. At the end of the each SRT operations, PUFs samples were soaked with 1:1 acetone:hexane for 24 hours. Then the PUFs samples were sonicated for 60 min after they were soaked in 1:1 acetone:hexane overnight. Using a rotary evaporator, the 1:1 acetone:hexane mixture was dried. The dried extract volume was increased to 5 mL with adding hexane after then, it was dried completely under a stream of high purity N2.
This process was repeated two times. Finally, the dried extract volume was adjusted to 1 mL with hexane.

Mass Balance Calculations for AHMT in Biological Reactors
Mass balance calculations were practiced according to the following equations. CW, CA and CS represent concentration in water, air and sludge, respectively. VW, VA and VA represent volume of the water in biological reactor, obtained extract volume from PUF disk for volatilization analysis and obtained extract volume from biological sludge for adsorption test, respectively. m1 and m2 represent dry weight of the sludge in analysis and dry weight of the sludge in biological reactor, respectively. M1 shows the AHMT amount in the supernatant of the biological reactor denominated in µg (Eq. 1). M2 shows the AHMT amount in the sludge of the biological reactor denominated in µg (Eq. 2). M3 shows the AHMT amount in the headspace of the biological reactor denominated in µg (Eq. 3). MT shows the total AHMT amount in the anaerobic/aerobic sequential biological reactor system denominated in µg (Eq. 4).

Statistical Analysis
The correlation (R 2 ) between data was performed using Excel Microsoft 2010 while the sensitivity analysis was performed in ANOVA (one-way) tests using an α-value of 0.05.

Results and Discussions Start-up Period of the Biological Treatment Processes
The anaerobic/aerobic sequential reactor system was operated for 20 days with synthetic wastewater at an SRT of 5 days corresponding to an organic loading rate of 0.18 gr COD/L × day to reach steady-state conditions by providing the acclimation of the anaerobic and  Table 2. During the anaerobic and aerobic phases, 0 and 2 mg L −1 dissolved oxygen was observed and the redox potential was around −610 and +145 mV, respectively.

COD and SCOD Removals in Continuous Operated Biological Reactors
During the 5 days of SRT operation, the maximum COD removal efficiency of the single anaerobic reactor was obtained as 51.3% with a COD effluent of 438.30 mg L −1 at a COD influent of 900.00 mg L −1 . For the single aerobic reactor, maximum COD removal efficiency was measured as 59.6% with an effluent COD of 177.07 mg L −1 at a COD influent of 438.30 mg L −1 . For the anaerobic/aerobic sequential reactor system, COD removal efficiency reached 80.3% with an effluent of 177.07 mg L −1 at a COD influent of 900.00 mg L −1 (Figure 2). Thereafter, SRT was increased to 30 days. For the anaerobic/aerobic sequential reactor system, COD removal efficiency reached 89.7% with an effluent COD concentration of 98.08 mg L −1 at a COD influent of 955.00 mg L −1 (Figure 2). Thirdly, SRT was increased to 45 days. COD removal efficiency of the anaerobic/aerobic sequential reactor system measured as 92.2% with an effluent COD concentration of 74.03 mg L −1 at a COD influent of 955.00 mg L −1 (Figure 2). Finally, when the SRT was increased to 55 days, COD removal efficiency of the anaerobic/aerobic sequential reactor system reached 94.1% with an effluent COD concentration of 55.68 mg L −1 at a COD influent of 950.00 mg L −1 (Figure 2). A linear correlation between COD yields and SRTs was found for anaerobic/aerobic sequential biological reactor system and this regression is significant (R 2 =0.96, P=0.006).
The maximum SCOD removal efficiency of the single anaerobic reactor was obtained as 40.4% with a SCOD effluent of 479.78 mg L −1 at a SCOD influent of 805.00 mg L −1 during the 5 days of SRT operation. For the single aerobic reactor, maximum SCOD removal efficiency was measured as 57.3% with an effluent SCOD of 204.87 mg L −1 at a SCOD influent of 479.78 mg L −1 . For the anaerobic/aerobic sequential reactor system, SCOD removal efficiency reached 74.6% with an effluent of 204.87 mg L −1 at a SCOD influent of 805.00 mg L −1 (Figure 3). The reactors were operated. When the SRT was increased to 30 days, for the anaerobic/aerobic sequential reactor system, SCOD removal efficiency reached 84.4% with an effluent SCOD concentration of 132.64 mg L −1 at a SCOD influent of 850.00 mg L −1 (Figure 3). SCOD removal efficiency of the anaerobic/aerobic sequential reactor system measured as 88.1% with an effluent SCOD concentration of 100.84 mg L −1 at a SCOD influent of 850.00 mg L −1 for the 45 days of SRT operation (Figure 3). For the 55 days of SRT, SCOD removal efficiency of the anaerobic/aerobic sequential reactor system reached 91.1% with an effluent SCOD concentration of 75.64 mg L −1 at a SCOD influent of 850.00 mg L −1 (Figure 3). A linear correlation between SCOD yields and SRTs was found for anaerobic/aerobic sequential biological reactor system and this regression is significant (R 2 =0.99, P=0.004).
The high performance in the sequential treatment can be attributed to the anaerobic pre-treatment used in order to biodegrade the already low COD and SCOD content prior to the aerobic stage. Some researchers reported that the removals of COD and soluble COD parameters gradually increased with increasing hydraulic retention time [17][18][19]. In our study, hydraulic and sludge retention times were equal to each other because of the biological reactors without sludge returns. In our study, although no significant differences in COD and SCOD yields were observed at 30, 45 and 55 days of SRTs, the highest COD and SCOD removal efficiencies were achieved at the longest SRT of 55 days in the sequential system. This could be attributed to the good acclimation of the microorganisms to the hospital wastewater characteristics. The reason for the slight decrease in COD and SCOD yields at the lowest SRT of 5 days is the low contact time of wastewater with sludge granules [20,21].

Reactor of the Sequential Reactor System
The TVFA concentration of the anaerobic reactor of the sequential reactor system reached 180 mg acetic acid L −1 at the end of the 5 days of SRT operation (Table 3). When the SRT was increased to 55 days, the TVFA concentration of the anaerobic reactor of the sequential reactor system decreased to 46 mg acetic acid L −1 (  [22,23]. In this study, TVFA to alkalinity ratios during the experimental studies were 0.12,  (Table 3).

Reactor of the Sequential Reactor System
In this study, average CH4 gas volumes of the anaerobic reactor of the sequential reactor system were determined as 161.6, 203.2, 226.3 and 234.1 mL CH4 day −1 for 5, 30, 45 and 55 days of SRT operations, respectively (Data not shown). As a consequence, increasing the SRT from 5 to 55 days positively affected the CH4 gas production. CH4 gas production at 55 days of SRT was better than the productions at 5, 30 and 45 days of SRT conditions. This could be due to the high CH4 gas production at high retention time from the low TVFA without any accumulation in the anaerobic UASB reactor.

AHMT Removals in Continuous Operated Biological Reactors
The influent AHMT concentration was detected as 236 µg L −1 in raw hospital wastewater ( In sewage treatment plants, AHMT removal of approximately 50 to more than 90% mainly caused by sorption onto sludge particles has been reported [3]. The results of this study showed that aerobic and anaerobic adsorption onto biological sludges was the main removal mechanism for AHMT under aerobic and anaerobic conditions, while biodegradation was medium and volatilization of AHMT was found to be negligible. The findings of our data showed that anaerobic and aerobic sludges were the main reservoir of AHMT, and their potential entry into environmental AHMT.

Conclusions
A comparative assessment of the biodegradation of AHMT with anaerobic/aerobic sequential biological reactor system under 5, 30, 45 and 55 days of SRT operations was investigated to evaluate the efficiency of the best SRT operation. 55 days of SRT operation under mesophilic conditions removed AHMT 42.3% with biodegradation from the supernatant while adsorption removal efficiency reached 57.5% in the biological sludge in the anerobic UASB/aerobic CSTR sequential biological reactor system. As a result of the study, increasing of the SRT has a positive effect on AHMT removals from the raw hospital wastewater effluents in anaerobic/aerobic sequential biological reactor system under mesophilic conditions.