Experimental and Numerical Analysis of a Low Environmental Impact Pyro-Gasiﬁcation System for the Energetic Valorization of Waste through a Biomass Steam Power Plant

: This paper addresses the study of a pyro-gasiﬁcation plant designed, built, and operated to recover inert metals from different types of solid waste. Experimental tests were carried out using pulper as the solid waste. However, while a reliable composition analysis of the produced syngas was carried out, a precise composition evaluation of the pulper used during the experimental activities was not performed and the related data were characterized by unacceptable uncertainty. Therefore, with the aim of reliably characterizing the plant operation, a thermochemical model of the gasiﬁcation process was setup to simulate the equilibrium operation of the plant and a vector optimization methodology was used to calibrate the numerical model. Then, a decision-making problem was solved to identify the most suitable optimal solution between those belonging to the Pareto optimal front, thus obtaining reliable composition data for the adopted pulper waste. In particular, four different identiﬁcation criteria were applied for the selection of small subset of solutions over the 3138 dominant solutions found. Among them, the solution (i.e., set of calibration parameters) that minimizes the experimental-numerical difference between the lower heating value of the produced syngas seemed to provide the most reliable approximation of the real plant operation. Finally, a possible plant conﬁguration is proposed for the energetic valorization of the pulper waste and its overall conversion process efﬁciency is estimated.


Introduction
The balance between energy supply and energy demand is a critical issue to address, as widely discussed in [1]. At the end of this century, the global energy demand is expected to be about six times greater than the current. Today, the available energy supply is much lower than the energy required in many of the developing countries. Moreover, fossil fuels are still the main primary sources of energy worldwide (Figure 1, [2]), covering approximately 82% of the total electricity generation [3][4][5].   [7,8].
Since traditional waste disposal is one of the major causes of environmental pollution, WtE technologies may significantly reduce the potential environmental impact of waste disposal. Therefore, WtE processes are considered among the most suitable options Although energy-related CO 2 emissions stalled in 2015 [6] because of the improvements in energy efficiency and an increasing use of low-carbon energy and renewable energy sources, a more efficient use of energy and an increasing use of renewable energy sources are still mandatory to limit the rise in the global average temperature below 2 • C above pre-industrial levels (Figure 2, [7,8]). In this scenario, alternative sources of energy such as those provided by emerging waste-to-energy (WtE) processes could play a fundamental role [9]. The problem of disposal of a huge quantity of generated waste along with the need of reliable sources of renewable energy are common in many developing countries. Therefore, the use of waste as a potential renewable energy source could be a useful solution, also meeting the increasing demand for energy [3]. Moreover, promoting technologies for waste valorization could be part of the policies to limit the global average temperature rise, entailing the increase in the share of renewable energy (i.e., biomass and waste in Figure 2) expected by 2050.
Processes 2021, 9, x FOR PEER REVIEW 2 of 18 such as those provided by emerging waste-to-energy (WtE) processes could play a fundamental role [9]. The problem of disposal of a huge quantity of generated waste along with the need of reliable sources of renewable energy are common in many developing countries. Therefore, the use of waste as a potential renewable energy source could be a useful solution, also meeting the increasing demand for energy [3]. Moreover, promoting technologies for waste valorization could be part of the policies to limit the global average temperature rise, entailing the increase in the share of renewable energy (i.e., biomass and waste in Figure 2) expected by 2050.  Since traditional waste disposal is one of the major causes of environmental pollution, WtE technologies may significantly reduce the potential environmental impact of waste disposal. Therefore, WtE processes are considered among the most suitable options  [7,8].
Since traditional waste disposal is one of the major causes of environmental pollution, WtE technologies may significantly reduce the potential environmental impact of waste disposal. Therefore, WtE processes are considered among the most suitable options to tackle waste-related problems [3]. A report from the World Bank estimates that waste generation will increase from 2.01 billion tons in 2016 to 3.40 billion tons in 2050 [10]. For this reason, in recent decades, possible solutions to disposal of municipal solid waste (MSW) in landfills are attracting much attention because of the clearly negative environmental impact deriving from inadequate waste management. Environmental issues include landscape impact, dust, and leachate production, and emissions of contaminating gases [11]. Some research works indicate how recycling could be, depending on the energy recovery technologies, a better option than energy recovery [5,12]. However, about 70% of the waste could be generally recycled. Therefore, whenever recovery and reuse of materials cannot be pursued, different treatment technologies can be adopted to effectively generate energy from waste, thus avoiding the use of landfills and leading to economic and environmental benefits [13][14][15].
Biological and thermochemical treatments are more commonly used; thermal treatments can be obtained through pyrolysis, gasification, or incineration [16]. Until recently, incineration was the most widespread WtE technology with more than 1400 incineration plants operating around the world [17]. However, even the last generation of waste incinerators are limited by low electric efficiency of about 22-25% [18] because of the maximum steam temperature at the boiler outlet, which is normally lower than 450 • C to prevent corrosion by gaseous HCl [19,20]. Moreover, the incineration process generates a lot of acid gases, heavy metals, dioxins, and other pollutants [21]. For these reasons, in recent years, a considerable interest has grown toward other WtE technologies, particularly pyrolysis and gasification [21]. Pyrolysis and gasification of waste can eliminate dioxin emissions [20]. In fact, the reducing atmosphere that characterizes gasification and pyrolysis processes strongly limits the emission of pollutants such as dioxins, furans, and NO X , as well as greenhouse gas emission [22][23][24][25][26][27][28][29][30][31][32]. Nevertheless, both pyrolysis and gasification processes present environmental issues that cannot be neglected. Pyrolysis, which can either be used as an independent process or pretreatment for gasification, produces tar, besides char and gas, whose proportion depends on both feedstock properties and operating parameters [23,24]. Therefore, in biomass gasification, beyond syngas production and CO 2 sequestration, there are major environmental concerns and problems in downstream equipment caused by tar production [25,26]. Another relevant problem is the formation of HCl, but also H 2 S and NH 3 , which occurs, for example, during gasification of MSW containing significant amounts of chlorine (due to the presence of polyvinyl chloride, PVC), sulfur, and heavy metals [27,28]. Both the liquid product of pyrolysis process, which is an acidic combustible liquid, and hydrochloric acid cause fouling, severe corrosion to downstream equipment, like a gas turbine or internal combustion engine, and poisoning of catalysts [29][30][31].
As for the energetic valorization of waste in WtE plants, it is widely recognized how a high energetic efficiency can be achieved by coupling pyrolysis and gasification plant to gas turbine, internal combustion engine, or combined-cycle gas-steam turbine power plants [22]. Therefore, WtE technologies provide a method to simultaneously address the problems related to energy demand, waste management, and greenhouse gas emissions. In addition, they can be included in a circular economy system (CES) [33]. CES refers to an economic strategy that suggests innovative ways to transform the current mainly linear consumption system into a circular one achieving economic sustainability through the necessary material savings [34]. Indeed, CES concept aims to extend the useful life of materials by promoting recycling while reducing use of resources and environmental impact [35]. The subject of the proposed research work is part of the problem described above and focuses on WtE technologies, pyrolysis, and gasification. Specifically, this work concerns the numerical and experimental analysis of a pyro-gasification plant originally designed, built, and operated to recover inert metals. Then, with the aim of ensuring a more flexible plant operation allowing biomass, plastics, metals, MSW, and other different type of waste to be treated, the capability of converting waste from paper processing (i.e., pulper) into synthesis gas (syngas), that can be profitably burned, has been tested. While a rigorous and certified composition analysis of the produced syngas was conducted, a precise composition evaluation of the pulper used during the experimental tests was not carried out. Hence, pulper waste has been characterized by an average proximate and ultimate analysis assumed as reference. Then, with the aim of reliably characterizing the plant operation and estimate the unknown chemical composition of the pulper waste, a thermochemical model of the process has been setup and then calibrated to simulate the equilibrium operation of the plant. Similar examples of this modeling approach can be found within the published literature [36][37][38][39][40][41][42][43][44]. However, the complex model calibration phase required the adoption of a specific vector optimization methodology proposed by the authors. In particular, starting from some of the available data obtained through the experimental tests, a multi-objective optimization problem has been set up and solved to reliably calibrate the numerical model and then simulate the real plant operation, obtaining time and cost savings by avoiding to perform further tests. More specifically, pulper composition, along with other process parameters, has been set as model calibration parameter and decision variables of the optimization problem. The differences between simulated and measured concentrations of the syngas components have been set as objective functions to be minimized. A subsequent decision-making process has been finally carried out to identify the most suitable solution (i.e., the most suitable model calibration) between those belonging to the Pareto optimal front, which provides reliable composition data for the adopted pulper waste. In particular, four different identification criteria have been applied for the selection of a single solution over the 3138 dominant solutions found. Finally, the solution (i.e., set of calibration parameters) which minimizes the experimental-numerical difference of the lower heating value of the produced syngas seemed to provide the most reliable approximation of the real plant operation, also considering the proposed energetic application consisting in the combustion of the outcoming syngas in a biomass steam power plant.

The MR System: Experimental Setup and Test
The material recovery plant is an indirect atmospheric pyro-gasifier making use of a methane burner and designed to recover metals and other inert from various types of solid waste. Being a medium-small scale plant, it has the advantage of local use, reducing management and transport costs. The plant can also process up to 1000 kg/h of paper pulper and can regulate the speed of the reactor chamber to adapt to waste variations. The average residence time of the solid waste in the reactor is about 30-40 min. Its transport is guaranteed by an internal spiral ring. The overall scheme of the plant is represented in Figure 3. It consists of the following main components: an open feeding section (1) through which the pulper is constantly fed together with the air used as gasifying agent, a methane combustor used to obtain hot gases (2), a rotary pyro-gasifier (3), a metals/inert discharging outlet (4), syngas/tar combustion chamber (5), and an exhaust gas treatment unit (6).
The present work is based on the results of an experimental test performed by feeding the MR pyro-gasification plant with a certain amount of paper pulper to be treated. Paper pulper is basically composed of polyethylene (PE) [40][41][42], possible cellulose residue, and other materials used in paperboards such as aluminum sheets and other plastics. With a moisture content of about 20% resulting from the wet process of maceration, the pulper, whose proximate and ultimate analysis derived from literature data [43] are shown in Table 1, is suitable for thermal treatment.
Some experimental tests have been carried out and the produced syngas has been object of an accurate composition analysis (Analysis was carried out by the accredited laboratory, CSA spa, http://www.csaricerche.com/en/laboratori_analisi.php; number of certification n. 500557-001), conducted with the methodology UNICHIM 542, certified by a specialized laboratory (Table 2).  The present work is based on the results of an experimental test performed by feeding the MR pyro-gasification plant with a certain amount of paper pulper to be treated. Paper pulper is basically composed of polyethylene (PE) [40][41][42], possible cellulose residue, and other materials used in paperboards such as aluminum sheets and other plastics. With a moisture content of about 20% resulting from the wet process of maceration, the pulper, whose proximate and ultimate analysis derived from literature data [43] are shown in Table 1, is suitable for thermal treatment. Some experimental tests have been carried out and the produced syngas has been object of an accurate composition analysis (Analysis was carried out by the accredited laboratory, CSA spa, http://www.csaricerche.com/en/laboratori_analisi.php; number of certification n. 500557-001), conducted with the methodology UNICHIM 542, certified by a specialized laboratory (Table 2).    Table 2. Composition of the produced syngas.

Chemical Species Experimental Value
Carbon dioxide The three parameters listed in Table 3 have been considered for the plant model calibration.

The Thermochemical Model
Since the physicochemical phenomena governing the conversion process of waste are limited to two plant components, the methane combustor and the pyro-gasifier (2 and 3 in Figure 3, respectively), the modeling has been focused on these two components. The estimation of the heat flow through the reactor walls ( . Q aux in Figure 4) has been also taken into account. The combustor (COMB. In Figure 4) is modelled as a reactor which calculates the exhaust gases properties through mass, energy, and chemical species balances under the assumption of complete methane combustion. The mass flow rates of air and methane that generate the inert gasifying environment which activates the gasification process through the interaction with waste in the first section of the pyro-gasifier represent two calibration variables of the model. Pulper, as previously discussed, has been characterized by an average proximate and ultimate analysis assumed as reference. However, the exact chemical composition was unknown. Assuming a prevalent polyethylene composition for the pulper and given the impossibility of the model adopted to handle polymeric raw material, the rotary drum of the pyro-gasifier has been schematized in two blocks. The pulper feedstock is first fed to a depolymerization block (DEPOLYM. in Figure 4) where it is decomposed into ethylene. This is a yield-oriented reactor model in which a prevalent composition of ethylene has been imposed as output according to the composition reported in Table 4. It is used to model pyrolysis and decomposition of waste (drying and devolatilization). Since only pulper is considered at the inlet of the depolymerization block, to take account of the air incoming through the open section of the feeding system, ultra-lean values of the equivalence ratio (λ in Table 5) have been considered within the possible operating conditions of the methane combustor to reliably estimate the whole air mass flow rate involved in the gasification process. The second block (GASIF. in Figure 4) has been used to model the typical gasification reactions (oxidation, reduction, and recombination).

The Thermochemical Model
Since the physicochemical phenomena governing the conversion process of waste are limited to two plant components, the methane combustor and the pyro-gasifier (2 and 3 in Figure 3, respectively), the modeling has been focused on these two components. The estimation of the heat flow through the reactor walls (̇ in Figure 4) has been also taken into account. The combustor (COMB. In Figure 4) is modelled as a reactor which calculates the exhaust gases properties through mass, energy, and chemical species balances under the assumption of complete methane combustion. The mass flow rates of air and methane that generate the inert gasifying environment which activates the gasification process through the interaction with waste in the first section of the pyro-gasifier represent two calibration variables of the model. Pulper, as previously discussed, has been characterized by an average proximate and ultimate analysis assumed as reference. However, the exact chemical composition was unknown. Assuming a prevalent polyethylene composition for the pulper and given the impossibility of the model adopted to handle polymeric raw material, the rotary drum of the pyro-gasifier has been schematized in two blocks. The pulper feedstock is first fed to a depolymerization block (DEPOLYM. in Figure  4) where it is decomposed into ethylene. This is a yield-oriented reactor model in which a prevalent composition of ethylene has been imposed as output according to the composition reported in Table 4. It is used to model pyrolysis and decomposition of waste (drying and devolatilization). Since only pulper is considered at the inlet of the depolymerization block, to take account of the air incoming through the open section of the feeding system, ultra-lean values of the equivalence ratio (λ in Table 5) have been considered within the possible operating conditions of the methane combustor to reliably estimate the whole air mass flow rate involved in the gasification process. The second block (GASIF. in Figure 4) has been used to model the typical gasification reactions (oxidation, reduction, and recombination).   Since the residence time of waste in the reactor is very long (30-40 min on average), it was assumed that this time was long enough to reach chemical equilibrium. Consequently, an equilibrium reactor that minimizes Gibbs free energy was used for the GASIF. Block. This model returns the syngas output flow (composition, temperature, pressure, mass flow rate) and the heat flow . Q aux , whether it has positive or negative values, as result. This schematization allows to model the gasification process by providing a complete chemical composition of the inlet waste. Since both DEPOLYM. And GASIF. Blocks refer to the same rotating drum reactor, the equality of the temperatures has been imposed as a constraint for the two sub-models (T depolym = T GASIF ). Ultimately, the gasification process has been ideally split into two stages: the first stage in which polyethylene, that is the main pulper component, is converted into its basic ethylene molecules. The second stage in which these molecules and the remaining reagents are further turned into the typical gaseous components of a syngas such as CO, CO 2 , H 2 , CH 4 . The plant model includes the calculation of the thermal energy flows that characterize the two blocks. The first ( . Q in Figure 4) represents the thermal power that, being generated in the second stage of the gasification process (GASIF. Block), supports the depolymerization process of polyethylene into ethylene (DEPOLYM. Block). The second ( . Q aux in Figure 4), represents the thermal power generated during the gasification process that is exchanged with the external environment, and so dissipated, through the walls of the gasification section. The result is a zero-dimensional stationary thermochemical model consisting of three control volumes where mass, energy, and chemical elements balances are carried out. Specifically, the following mass and energy balance equations are used: . m pul p c p,pul p ·T env + H i,pul p + • Gasification process (GASIF. in Figure 4):

Thermochemical Model Calibration: The Proposed Multi-Objective Optimization Approach
As previously said, after the experimental test a precise composition analysis of the produced syngas has been conducted. However, thorough evaluation concerning the composition of the pulper used during the experimental tests was not carried out. Therefore, to reliably calibrate the thermochemical model, a multi-objective optimization methodology based on the use of a genetic algorithm has been adopted. In particular, according to the logic scheme represented in Figure 5, starting from the available data obtained through the experimental tests, a vector optimization problem has been set up and solved to reliably calibrate the numerical model and simulate the actual plant operation. More specifically, the average reactor temperature (T depolym ), air ( . m air ), and methane ( . m CH4 ) mass flow rates, fraction of hydrogen (H 2depolym ), carbon (C depolym ), and ethylene (ethylene depolym ) produced by the depolymerization process have been set as model calibration parameter (as they are unknown) and decision variables of the optimization problem. The differences between simulated and measured concentrations of the syngas constituents (i.e., syngas composition) have been set as objective functions to be minimized.

Thermochemical Model Calibration: The Proposed Multi-Objective Optimization Approach
As previously said, after the experimental test a precise composition analysis of the produced syngas has been conducted. However, thorough evaluation concerning the composition of the pulper used during the experimental tests was not carried out. Therefore, to reliably calibrate the thermochemical model, a multi-objective optimization methodology based on the use of a genetic algorithm has been adopted. In particular, according to the logic scheme represented in Figure 5, starting from the available data obtained through the experimental tests, a vector optimization problem has been set up and solved to reliably calibrate the numerical model and simulate the actual plant operation. More specifically, the average reactor temperature ( ), air (̇), and methane (̇4) mass flow rates, fraction of hydrogen ( 2 ), carbon ( ), and ethylene ( ℎ ) produced by the depolymerization process have been set as model calibration parameter (as they are unknown) and decision variables of the optimization problem. The differences between simulated and measured concentrations of the syngas constituents (i.e., syngas composition) have been set as objective functions to be minimized. The optimization problem has been solved through the genetic algorithm MOGA II (i.e., the Multi-Objective Genetic Algorithm II), whose main features include directional cross-over and elitism, that is used to prevent early convergence to local optimum [8,[45][46][47][48]. Starting from an initial population providing a set of initial solutions, the MOGA II The optimization problem has been solved through the genetic algorithm MOGA II (i.e., the Multi-Objective Genetic Algorithm II), whose main features include directional cross-over and elitism, that is used to prevent early convergence to local optimum [8,[45][46][47][48]. Starting from an initial population providing a set of initial solutions, the MOGA II identifies the best individuals by mean of classical crossover, directional crossover, mutation, selection, their predefined operator probabilities, and the use of elitism. Tables 5 and 6 show details concerning decision variables and objective functions adopted for the optimization problem.
The ranges imposed to the decision variables have been set wide enough to include most of the operating conditions. Carbon and hydrogen concentrations depend on the ethylene fraction as shown in the following.

Species
Objective Functions

Optimization Results and Decision-Making Problem
The model calibration procedure allowed to find the Pareto front, consisting of a set of 3138 different optimal solutions. For example, Figure 6 shows the projection of these solutions on two different planes of the objective functions space. Therefore, a decisionmaking problem has been addressed to identify a single optimal solution providing the most reliable composition data for the adopted pulper waste and plant operation over the dominant solutions found. In particular, the following four different identification criteria have been applied:    The application of these criteria led to the identification of four different optimal solutions, each of them characterized by specific values of decision variables (Table 7) and objective functions (namely syngas composition, Table 8). In the first and third case (CR.1 and CR.3), considering the respective axes origin as the single ideal optimal solution, the Pareto solution that is closest to axes origin is privileged (ID 409 and ID 1933, respectively). Criteria CR.2 and CR.4 enabled the identification of the solutions labeled ID 372 and ID 1205, respectively. In particular, the last solution is characterized by a LHV of 5.137MJ/kg, which almost corresponds to the experimental value. The application of these criteria led to the identification of four different optimal solutions, each of them characterized by specific values of decision variables (Table 7) and objective functions (namely syngas composition, Table 8). In the first and third case (CR.1 and CR.3), considering the respective axes origin as the single ideal optimal solution, the Pareto solution that is closest to axes origin is privileged (ID 409 and ID 1933, respectively). Criteria CR.2 and CR.4 enabled the identification of the solutions labeled ID 372 and ID 1205, respectively. In particular, the last solution is characterized by a LHV of 5.137MJ/kg, which almost corresponds to the experimental value. To highlight the predictive capability of the four solutions, the same syngas composition results shown in Table 8 have been properly represented in Figure 8.
In particular, a more significant representation has been obtained by plotting the results in terms of relative error between numerical and experimental concentration of each syngas component. This way, the more the red curve, representing the values provided by the solutions under investigation, approaches the x-axis, the more the numerical result is close to the experimental one. It can be noted that the numerical values shown on the x-axis (i.e., y-axes origins) represent the measured concentrations of the individual chemical species. Figure 8 clearly shows how solutions 372, 1933, and 1205 provide a more accurate syngas composition than solution 409.
Considering the energetic application that will be subsequently discussed, consisting in the combustion of the resulting syngas in a biomass steam power plant, a LHV comparison has been also carried out between the four solutions obtained through the decision-making process. The LHV calculation implies a weighted average calculation of the LHV of the individual chemical species which compose the syngas (Table 9): where m i is the mass flow rate of the individual species which may be affected by combustion phenomena and m tot is the total syngas mass flow rate.  Results in Table 9 clearly show how solution 1205 (CR.4) is characterized by a LHV that is very close to the experimental value. Therefore, this solution shows almost the same energy content of the actual syngas as well as a reasonable estimation of the syngas volumetric composition.
To identify the most reliable solution, the four solutions (i.e., model calibration and related results) found in the previous part have been further compared according to a secondary level (bottoming) decision-making criteria.
To identify a single optimal solution among those belonging to the Pareto optimal front, some authors adopted the minimum distance from the origin of a n-dimensions hyperspace, considered as an ideal optimum, as decision-making-criteria [49,50]. Furthermore, many different criteria have been proposed in the literature [51]. In this paper, considering the specific application consisting in the combustion of the syngas in a biomass steam power plant and the estimation of its global efficiency, the authors proposed the minimization of the error between calculated and measured LHV as supplementary (bottoming) decision-making criteria, thus privileging the energy content of the syngas.
Since the objective of the optimization problem was to minimize the difference between calculated and measured syngas composition, a first comparison has been made is in terms of syngas composition (Figure 8). While solutions CR.2, CR.3, and CR.4 show a similar syngas composition, which are also closer to the experimental data (red curve), solution CR.1 (yellow curve in Figure 8) is characterized by quite different concentrations. Eventually, considering the energetic application discussed below, which consists in the combustion of the resulting syngas in a biomass steam power plant, the solution CR.4 (green line) has been preferred. In fact, besides a favorable value of the average percentage error related to the volumetric concentrations of the syngas components (about 17%), as previously discussed, solution CR.4 has also almost the same energy content experimentally measured (5.138 MJ/kg).   Table 9 clearly show how solution 1205 (CR.4) is characterized by a LHV that is very close to the experimental value. Therefore, this solution shows almost the same energy content of the actual syngas as well as a reasonable estimation of the syngas volumetric composition.

Results in
To identify the most reliable solution, the four solutions (i.e., model calibration and related results) found in the previous part have been further compared according to a secondary level (bottoming) decision-making criteria.
To identify a single optimal solution among those belonging to the Pareto optimal front, some authors adopted the minimum distance from the origin of a n-dimensions hyperspace, considered as an ideal optimum, as decision-making-criteria [49,50]. Furthermore, many different criteria have been proposed in the literature [51]. In this paper, considering the specific application consisting in the combustion of the syngas in a biomass steam power plant and the estimation of its global efficiency, the authors proposed the minimization of the error between calculated and measured LHV as supplementary (bottoming) decisionmaking criteria, thus privileging the energy content of the syngas. Table 9. Syngas combustible species and reference LHV values adopted for the LHV calculation.  Since the objective of the optimization problem was to minimize the difference between calculated and measured syngas composition, a first comparison has been made is in terms of syngas composition ( Figure 8).
While solutions CR.2, CR.3, and CR.4 show a similar syngas composition, which are also closer to the experimental data (red curve), solution CR.1 (yellow curve in Figure 8) is characterized by quite different concentrations. Eventually, considering the energetic application discussed below, which consists in the combustion of the resulting syngas in a biomass steam power plant, the solution CR.4 (green line) has been preferred. In fact, besides a favorable value of the average percentage error related to the volumetric concentrations of the syngas components (about 17%), as previously discussed, solution CR.4 has also almost the same energy content experimentally measured (5.138 MJ/kg).
It is worth noting that the application of the four decision-making criteria enabled the identification of solutions characterized by significantly different values of some plantoperating parameters. Consequently, the four solutions identified are characterized by wide dispersion ranges of the process parameters. Figure 9, for example, highlights the dispersion ranges with reference to the average reactor temperature and the energy efficiency of the conversion process. Figure 9 also shows how solution CR.4 is characterized by temperature and efficiency values that are closer to the average value calculated from the four solutions identified.
Starting from the calibration parameters of the model that characterize solution CR.4, the interaction between the exhaust gas from the methane combustor and the pulper at ambient temperature (293 K) within the mixing region of the rotary drum has been analyzed ( Figure 10). This work has been also focused on the estimation of the expected conditions that occur in the initial section of the pyro-gasification reactor. Results shows a temperature of 1540 K. Therefore, it is assumed that the waste is affected by flash pyrolysis phenomena [52] leading to rapid heating up to the estimated high temperature.
the identification of solutions characterized by significantly different values of some plant-operating parameters. Consequently, the four solutions identified are characterized by wide dispersion ranges of the process parameters. Figure 9, for example, highlights the dispersion ranges with reference to the average reactor temperature and the energy efficiency of the conversion process. Figure 9 also shows how solution CR.4 is characterized by temperature and efficiency values that are closer to the average value calculated from the four solutions identified. Starting from the calibration parameters of the model that characterize solution CR.4, the interaction between the exhaust gas from the methane combustor and the pulper at ambient temperature (293 K) within the mixing region of the rotary drum has been analyzed ( Figure 10). This work has been also focused on the estimation of the expected conditions that occur in the initial section of the pyro-gasification reactor. Results shows a temperature of 1540 K. Therefore, it is assumed that the waste is affected by flash pyrolysis phenomena [52] leading to rapid heating up to the estimated high temperature.  Starting from the calibration parameters of the model that characterize solution CR.4, the interaction between the exhaust gas from the methane combustor and the pulper at ambient temperature (293 K) within the mixing region of the rotary drum has been analyzed ( Figure 10). This work has been also focused on the estimation of the expected conditions that occur in the initial section of the pyro-gasification reactor. Results shows a temperature of 1540 K. Therefore, it is assumed that the waste is affected by flash pyrolysis phenomena [52] leading to rapid heating up to the estimated high temperature.

Application: Coupling the Pyro-Gasification Plant with a Biomass Steam Power Plant
To evaluate the efficiency potential of the entire conversion process that starts from the gasification of pulper waste through the studied pyro-gasification plant ends with the electric power generation obtained through the combustion of both biomass and resulting syngas in a biomass steam power plant (BSPP), the plant scheme in Figure 11 has been considered. The biomass steam power plant used as a reference in this study, whose main data are summarized in Table 10, has been the object of experimental and numerical investigation in previous studies [53,54]. Specifically, it is assumed that syngas, and also char and tar, obtained through the gasification process are used to produce steam in the BSPP together with biomass; moreover, also the exhaust gas has been directed to the combustion chamber of the steam power plant to exploit the residual enthalpy at relative high temperature, thus also mitigating the inherent steam production "instability" of the BSPP alone [55]. Indeed, biomass has high moisture content variability that causes fluctuations in LHV, combustion chamber gas temperature, steam production, and electric power generation. Therefore, the proposed configuration has the advantage of reducing plant operation fluctuations [55]. standard configuration [35].

Biomass Mass Flow Rate
2498 kg/h Gross electric power 2688 kW Electric power for auxiliary 320 kW Net electric power 2368 kW Electric efficiency 23% Figure 11. Configuration of whole gasifier-biomass steam power plant [54].
To keep the nominal point operation of the steam cycle section (Section 2 in Figure 11), the original value of biomass mass flow rate (Table 10) has to be adjusted. Therefore, the biomass mass flow rate has been reduced to 1481 kg/h (reduction of 40.7%). If the following equation is used to evaluate the global efficiency of the whole plant: Exhaust gas Figure 11. Configuration of whole gasifier-biomass steam power plant [54]. To keep the nominal point operation of the steam cycle section (Section 2 in Figure 11), the original value of biomass mass flow rate (Table 10) has to be adjusted. Therefore, the biomass mass flow rate has been reduced to 1481 kg/h (reduction of 40.7%). If the following equation is used to evaluate the global efficiency of the whole plant: a value of 0.155 is obtained, which seems a very low value. However, considering that syngas resulting from the gasification process is produced from waste, whose energy content would otherwise be lost, a more appropriate efficiency estimation can be done through the following equation that does not consider pulper waste as energy input to the thermodynamic cycle: leading to a value of 0.262 that is 3 per cent higher than the original value shown in Table  10. When it is assumed to supply the pyro-gasification system with biomass the innovative plant configuration could be classified as a fully renewable power plant. In this context, the proposed configuration ( Figure 11) could be applied to the existing steam power plants as a solution to increase the global efficiency and, contemporary, to exploit a larger part of the biomass waste.

Conclusions
The increasingly pressing issue of sustainable waste treatment combined with the continuous search for new energy resources has led, in recent years, to an increasing attention to waste energy recovery systems. One of the most efficient and least polluting technologies is pyro-gasification. This paper described an experimental activity carried out on a pyro-gasification plant, from which it was not possible to obtain certain values for the input variables. Therefore, to reliably calibrate the thermochemical model of the investigated plant, a vector optimization problem, based on the evolutionary genetic algorithm MOGA II, has been solved. The results from the solution of the proposed optimization problem allowed for the determination of a Pareto optimal front between the eleven objective functions, and the adoption of the selection criterion requiring the minimization of the difference between calculated and experimental value of the LHV of the syngas allowed the identification of a single optimal solution used for the model calibration. Results show that the proposed methodology provides a useful and flexible tool for reliable model calibration. Future works will address more detailed analyses of the process through a kinetic model allowing the instantaneous simulation of the thermochemical conversion processes along the entire length of the reactor.