Insights into the Synergistic Effect and Inhibition Mechanism of Composite Conditioner on Sulfur-Containing Gases during Sewage Sludge Pyrolysis

Sewage sludge odorous gas release is a key barrier to resource utilization, and conditioners can mitigate the release of sulfur-containing gases. The gas release characteristics and sulfur compound distribution in pyrolysis products under both single and composite conditioning strategies of CaO, Fe2O3, and FeCl3 were investigated. This study focused on the inhibition mechanisms of these conditioners on sulfur-containing gas emissions and compared the theoretical and experimental sulfur content in the products to evaluate the potential synergistic effects of the composite conditioners. The findings indicated that at 650 °C, CaO, Fe2O3, and FeCl3 inhibited H2S release by 35.8%, 23.2%, and 9.1%, respectively. Notably, the composite of CaO with FeCl3 at temperatures ranging from 350 to 450 °C and the combination of Fe2O3 with FeCl3 at 650 °C were found to exert synergistic suppression on H2S emissions. The strongly alkaline CaO inhibited the metathesis reaction between HCl, a decomposition product of FeCl3, and the sulfur-containing compounds within the sewage sludge, thereby exerting a synergistic suppression on the emission of H2S. Conversely, at temperatures exceeding 550 °C, the formation of Ca-Fe compounds, such as FeCa2O4, appeared to diminish the sulfur-fixing capacity of the conditioners, resulting in increased H2S emissions. For instance, the combination of CaO and FeCl3 at 450 °C was found to synergistically reduce H2S emissions by 56.3%, while the combination of CaO and Fe2O3 at 650 °C synergistically enhances the release of H2S by 23.6%. The insights gained from this study are instrumental in optimizing the pyrolysis of sewage sludge, aiming to minimize its environmental footprint and enhance the efficiency of resource recovery.


Introduction
Sewage sludge, referred to as 'sludge' hereinafter, is characterized by its high water content and rich organic matter [1].Sludge pyrolysis technology involves the thermal chemical transformation of sludge through heating under a high-temperature, inert atmosphere, which yields products such as char, tar, and non-condensable gases [2].Pyrolysis not only facilitates the reduction in and harmless treatment of sludge, but also can obtain fuel or high-value carbon-containing materials, such as adsorbents or soil amendments [3].During the pyrolysis process, various factors influence the generation and characteristics of the products, with temperature being one of the key factors [2].Generally, an increase in temperature leads to a reduced yield of char and tar, while simultaneously leading to an increased yield of gaseous products.Additionally, the residence time of the sludge at the target pyrolysis temperature is an important parameter that affects the secondary reactions of tar and gas yield, as well as the specific surface area of the char [4].
The pyrolysis of sludge is accompanied by the emission of numerous odorous sulfurcontaining gases, including H 2 S, SO 2 , CH 3 SH, CS 2 , and COS [1,5].These compounds are particularly concerning due to their low olfactory detection thresholds, H 2 S, for instance, can be detected at concentrations as low as 0.00041 mg/kg.The presence of such gases can have a profound negative impact on both human health and ecological systems [4,6,7].The release of these noxious odors during sludge pyrolysis has become a significant impediment to the advancement of pyrolysis technologies [8].Consequently, there is an urgent need for effective management of these sulfurous odorous emissions to facilitate the resourceful utilization of sludge [9].
A substantial residue of dewatering conditioners, such as Fe-based and Ca-based conditioners, remains within the sludge.The introduction of these conditioners significantly influences the emission of sulfur-containing gases during the sludge pyrolysis process.Kwon et al. observed that CaCO 3 decomposes to CaO at high temperatures, which can effectively capture sulfurous gases [10].This finding is supported by Cao et al., who showed that CaO can immobilize over 70% of sulfur in the form of inorganic sulfates and sulfides within the char [11].Concurrently, Liu et al. noted a reduction in H 2 S emissions with the addition of FeCl 3 , particularly at pyrolysis temperatures between approximately 600 and 800 • C, yet an unexpected increase was observed when the temperature was further increased to 800~950 • C [12].This suggests that the effects of various conditioners on the process are temperature-dependent and warrant additional investigation to elucidate the underlying mechanisms.
Composite conditioners have the potential to more effectively control the release of sulfurous gas emissions during sludge pyrolysis.Although a limited number of studies have explored the effects of composite conditioners, they have suggested possible synergistic effects.For instance, Liu et al. demonstrated that the concurrent addition of Fenton's reagent and CaO is beneficial for the retention of greater sulfur content in the char during pyrolysis [13].However, the synergistic mechanism behind this phenomenon remains unexplained.Additionally, Li et al. found that at 300 • C, a composite of Ca(OH) 2 and Fe 2 O 3 positively contributes to the fixation of SO 2 emitted from pyrolysis [6].Nonetheless, a quantitative evaluation of the synergistic effect was not performed.Therefore, it is necessary to conduct a quantitative assessment of the synergistic effects of composite conditioners and to thoroughly investigate their mechanisms in sulfur transformation.This will help advance the development of sludge treatment technologies, leading to resource utilization and causing the harmlessness of sludge.
In response, the present study employs commonly used inorganic conditioners CaO, Fe 2 O 3 , and FeCl 3 .These are blended in ratios of 1:1, 2:1, and 1:2 to form the composite conditioners.By contrasting the theoretical and actual emissions of sulfur-containing gases throughout the pyrolysis of composite-conditioned sludge at various temperatures, a quantitative analysis of the composites' synergistic impacts is conducted.Additionally, the distribution of sulfurous substances in pyrolysis products is examined, with a particular focus on the sulfur forms in solid residues, to elucidate the synergistic mechanisms of the composite conditioning agents.The findings of this study provide a theoretical foundation for the efficient, cost-effective, and resource-orientated utilization of sludge.

Sulfur Balance
The distribution of sulfur within the products derived from raw sludge (RS) and conditioned sludge is depicted in Table 1, which is similar to previous studies showing that sulfur-containing substances were not detected in tar [14].It is apparent that a significant portion of sulfur was retained in char, with 79.1% of sulfur being found in the RS-char and 15.1% existing in the gaseous phase.In comparison to RS, the proportion of char-S increased, and gas-S reduced in conditioned sludge.Notably, RS-CaO exhibited an 11.5% increase in char-S and an 8.1% decrease in gas-S.The application of Fe-based conditioners, particularly Fe 2 O 3 , similar to CaO, resulted in a 10.7% increase in char-S content for RS-Fe 2 O 3 and a 6.4% increase for RS-FeCl 3 , while the gas-S was diminished by 8.2% and 5.2%, respectively.Overall, these results indicate that the three types of conditioners are effective in enhancing the sequestration of sulfur in char and reducing its release into the gaseous state.To investigate the impact of conditioners on the emission of sulfur-containing gases throughout sludge pyrolysis, a comprehensive analysis was performed to identify and quantify these gases.Figure 1 illustrates that the pyrolysis of RS primarily results in the release of H 2 S, which constitutes 85.3% of the total sulfur-containing gases emitted, followed by COS, CS 2 , SO 2 , and CH 3 SH in terms of abundance.It is hypothesized that H 2 S originates from the desulfurization of both aliphatic and aromatic sulfur compounds, COS is likely formed through the interaction of C=O with SH or via the reaction between CO 2 and H 2 S [15].The increase in CS 2 is connected to the decomposition of COS, and the release of SO 2 is linked to the oxidation of organic sulfur species, whereas the formation of CH 3 SH is attributed to secondary reactions taking place within the char matrix [16,17].
increase in char-S and an 8.1% decrease in gas-S.The application of Fe-based conditio particularly Fe2O3, similar to CaO, resulted in a 10.7% increase in char-S content for Fe2O3 and a 6.4% increase for RS-FeCl3, while the gas-S was diminished by 8.2% and 5 respectively.Overall, these results indicate that the three types of conditioners are e tive in enhancing the sequestration of sulfur in char and reducing its release into the eous state.

Char-S (%)
Gas-S (%) Tas-S (%) RS-700 79.To investigate the impact of conditioners on the emission of sulfur-containing g throughout sludge pyrolysis, a comprehensive analysis was performed to identify quantify these gases.Figure 1 illustrates that the pyrolysis of RS primarily results in release of H2S, which constitutes 85.3% of the total sulfur-containing gases emitted lowed by COS, CS2, SO2, and CH3SH in terms of abundance.It is hypothesized that originates from the desulfurization of both aliphatic and aromatic sulfur compounds, is likely formed through the interaction of C=O with SH or via the reaction between and H2S [15].The increase in CS2 is connected to the decomposition of COS, and the rel of SO2 is linked to the oxidation of organic sulfur species, whereas the formation of CH is attributed to secondary reactions taking place within the char matrix [16,17].The three conditioners significantly suppressed the emission of H2S.Compare RS, the addition of these conditioners led to a reduction of H2S release, ranging from 56%.Variations in the release of other sulfur-containing gases were observed; howe these alterations represented less than 1.3% of the total sulfur in RS.This indicates H2S is more likely to be produced during sludge pyrolysis, and other types of sulfurtaining gases are more difficult to produce through secondary reactions, which is rel The three conditioners significantly suppressed the emission of H 2 S. Compared to RS, the addition of these conditioners led to a reduction of H 2 S release, ranging from 33 to 56%.Variations in the release of other sulfur-containing gases were observed; however, these alterations represented less than 1.3% of the total sulfur in RS.This indicates that H 2 S is more likely to be produced during sludge pyrolysis, and other types of sulfur-containing gases are more difficult to produce through secondary reactions, which is related to the higher H/C ratio of sludge compared with coal [16,17].Given that the decrease in H 2 S for RS-CaO, RS-Fe 2 O 3 , and RS-FeCl 3 is nearly mirrored by the increase in char-S, as depicted in Table 1, it is viable to discuss the impact of the conditioners with a focus on H 2 S. A comparison of the effects of different conditioners reveals that, following the pyrolysis of RS-CaO, the release of H 2 S constituted 5.7% of the total sludge sulfur, signifying a 55.3% reduction compared to RS.This reduction is likely due to the inhibition of desulfurization reactions involving aliphatic and aromatic sulfur compounds by CaO, or the capture of the acidic gas due to the strong alkalinity of CaO [14].Fe-based conditioners, such as Fe 2 O 3 and FeCl 3 , exhibited similar effects, leading to a 56.1% and 32.7% decrease in H 2 S release, respectively.This is due to the effects of Fe-based conditioners being analogous to that of CaO, which can inhibit the decomposition of aliphatic and aromatic sulfur species or capture gas-S [18,19].Based on the preceding analysis, sulfur in the products is present as char-S and gas-S, with H 2 S being the predominant sulfur-containing gas.Consequently, subsequent studies concentrated on the release variations of H 2 S and the content changes of different sulfur forms in the solid products, thereby facilitating an in-depth analysis of the synergistic effects and the underlying mechanisms of the conditioners.

Effect of Single Conditioner
The effects of CaO, Fe 2 O 3 , and FeCl 3 on H 2 S emissions during the sludge pyrolysis at various temperatures are depicted in Figure 2. As the temperature increased from 350 • C to 650 • C, the emission of H 2 S from RS gradually increased from 1.3% to 10%.This phenomenon is attributed to the exacerbated decomposition of aliphatic and aromatic sulfur-containing compounds within the sludge as the temperature elevates [18].Notably, between 450 • C and 550 • C, the concentration of H 2 S experienced a fivefold surge, rising from 1.4% to 7.3%.This observation suggests that at 550 • C, there significant sulfur decomposition within the RS, resulting in a pronounced enhancement in H 2 S yield.
to the higher H/C ratio of sludge compared with coal [16,17].Given that the decrea H2S for RS-CaO, RS-Fe2O3, and RS-FeCl3 is nearly mirrored by the increase in chardepicted in Table 1, it is viable to discuss the impact of the conditioners with a focu H2S.A comparison of the effects of different conditioners reveals that, following the rolysis of RS-CaO, the release of H2S constituted 5.7% of the total sludge sulfur, signif a 55.3% reduction compared to RS.This reduction is likely due to the inhibition of de furization reactions involving aliphatic and aromatic sulfur compounds by CaO, o capture of the acidic gas due to the strong alkalinity of CaO [14].Fe-based condition such as Fe2O3 and FeCl3, exhibited similar effects, leading to a 56.1% and 32.7% decr in H2S release, respectively.This is due to the effects of Fe-based conditioners being a ogous to that of CaO, which can inhibit the decomposition of aliphatic and aromatic su species or capture gas-S [18,19].Based on the preceding analysis, sulfur in the produc present as char-S and gas-S, with H2S being the predominant sulfur-containing gas.C sequently, subsequent studies concentrated on the release variations of H2S and the tent changes of different sulfur forms in the solid products, thereby facilitating an in-d analysis of the synergistic effects and the underlying mechanisms of the conditioners

Effect of Single Conditioner
The effects of CaO, Fe2O3, and FeCl3 on H2S emissions during the sludge pyrolys various temperatures are depicted in Figure 2. As the temperature increased from 35 to 650 °C, the emission of H2S from RS gradually increased from 1.3% to 10%.This nomenon is attributed to the exacerbated decomposition of aliphatic and aromatic su containing compounds within the sludge as the temperature elevates [18].Notably tween 450 °C and 550 °C, the concentration of H2S experienced a fivefold surge, ri from 1.4% to 7.3%.This observation suggests that at 550 °C, there significant sulfur composition within the RS, resulting in a pronounced enhancement in H2S yield.For sludge amended with conditioners, CaO consistently reduced the emissio H2S across the temperature range of 350~650 °C, exhibiting an inhibitory effect ov broad temperature interval.In contrast, Fe2O3 exerted an inhibitory impact on H2S w the temperature range of 550~650 °C, while FeCl3 manifested a positive influence ex For sludge amended with conditioners, CaO consistently reduced the emission of H 2 S across the temperature range of 350~650 • C, exhibiting an inhibitory effect over a broad temperature interval.In contrast, Fe 2 O 3 exerted an inhibitory impact on H 2 S within the temperature range of 550~650 • C, while FeCl 3 manifested a positive influence exclusively at 650 • C.These observations suggest that the underlying mechanisms of their inhibitory actions varied, thereby conferring distinct suppressive or promotional effects on H 2 S emissions at specific temperatures.Detailed discussion is as follows: CaO exhibited the most effective suppression of H 2 S emissions, achieving a reduction between 31.2% and 51.3% relative to RS.In comparison, the inhibitory effects of Fe 2 O 3 and FeCl 3 were less significant.At temperatures ranging from approximately 550 to 650 • C, Fe 2 O 3 diminished H 2 S release by 27.3% and 23.2%, respectively, while FeCl 3 only exhibited a 9.1% reduction at 650 • C. The strong alkalinity of CaO is likely responsible for the direct capture of acidic gases such as H 2 S, leading to the formation of stable calcium-sulfur compounds.These compounds immobilize sulfur within the char and reduce the release of sulfur in gaseous form [11]. Furthermore, the oxidizing nature of CaO can promote the transformation of organic sulfur compounds such as aliphatic sulfur and aromatic sulfur into more stable sulfoxides and sulfones [20].On the other hand, Fe 2 O 3 , with its attenuated alkaline properties, is likely to immobilize sulfur primarily through the formation of stable sulfur-containing substances at higher temperatures.The effectiveness of FeCl 3 at high temperatures may be ascribed to its transformation into Fe 2 O 3 .
Within the temperature range from 350 to 450 • C, both Fe 2 O 3 and FeCl 3 demonstrated a promotional effect on the emission of H 2 S, with a particular emphasis on FeCl 3 .This phenomenon may stem from the catalytic properties of Fe, which may lower the activation energy required for the decomposition of organic sulfur compounds, thereby reducing its decomposition temperature [12].According to Hu et al., the activation energy was reduced by 7.38% during the co-pyrolysis process due to the presence of Fe [21].Furthermore, the role of Cl is of greater significance in enhancing the release of sulfur-containing gases.For instance, the decomposition of FeCl 3 can yield HCl (reaction1), which may react with stable inorganic sulfides, leading to the formation of chlorides and the liberation of H 2 S [15].

Synergistic Effect of Composite Conditioner
The theoretical emission of H 2 S throughout the pyrolysis of composite-conditioned sludge was derived from the calculated release when each conditioner was applied individually.Observations from Figure 3a-f indicate that a synergistic enhancement of H 2 S emission occurred within the temperature range of 550~650 • C when CaO was combined with Fe 2 O 3 (or FeCl 3 ), with the actual emissions exceeding the theoretical predictions.This divergence intensified as the temperature rose.For example, at a 1:1 ratio of CaO to Fe 2 O 3 , the actual emission exceeded the theoretical predictions by 1.2% at 650 • C.This could be attributed to the sintering reaction between CaO and Fe 2 O 3 at high temperatures, potentially leading to the formation of Ca-Fe compounds such as Ca 2 Fe 2 O 5 [12].As a result, the quantity of CaO available to react with sulfur is reduced, thereby diminishing its ability to immobilize H 2 S [22].Similar patterns were detected when CaO and Fe 2 O 3 were combined at ratios of 2:1 and 1:2, with the actual emissions at 650 • C being 0.7% and 1.7% greater than the theoretical values, respectively.This suggests that a higher concentration of Fe 2 O 3 promotes the formation of Ca-Fe compounds, which subsequently impedes the inhibition of H 2 S release.
Furthermore, an examination of Figure 3a-f indicates that within the 350~450 • C temperature range, the composite of CaO and Fe 2 O 3 displayed negligible synergistic action, while the combination of CaO and FeCl 3 resulted in a synergistic suppression of H 2 S release, with actual emission levels being lower than the theoretical prediction.As depicted in Figure 2, which concerned the individual conditioning process, FeCl 3 decomposed at higher temperatures to yield Fe 2 O 3 and HCl.The formed HCl can react with inorganic or organic sulfur compounds in the sludge, thus facilitating the production of H 2 S. Consequently, the strong alkalinity of CaO, when combined with FeCl 3 , may neutralize the acidic conditions arising from the decomposition of FeCl 3 , thereby effectively reducing the emission of H 2 S. Furthermore, an examination of Figure 3a-f indicates that within the 350~450 °C temperature range, the composite of CaO and Fe2O3 displayed negligible synergistic action, while the combination of CaO and FeCl3 resulted in a synergistic suppression of H2S release, with actual emission levels being lower than the theoretical prediction.As depicted in Figure 2, which concerned the individual conditioning process, FeCl3 decomposed at higher temperatures to yield Fe2O3 and HCl.The formed HCl can react with inorganic or organic sulfur compounds in the sludge, thus facilitating the production of H2S.Consequently, the strong alkalinity of CaO, when combined with FeCl3, may neutralize the acidic conditions arising from the decomposition of FeCl3, thereby effectively reducing the emission of H2S.
In contrast to the combination of CaO with Fe-based conditioners, Figure 3g-i demonstrate that the composite of Fe2O3 and FeCl3 induced a synergistic promotion effect on H2S release between approximately 350 and 550 °C.This effect is attributed to the fact that at lower temperatures, both Fe2O3 and FeCl3 enhance the release of H2S, with FeCl3 having a particularly significant impact (as depicted in Figure 2).Notably, Figure 3i reveals that the combination of CaO and FeCl3 at a 1:2 ratio exhibited a more pronounced synergistic promotion effect compared to other composite ratios.This again indicates that the promotional effect on H2S release may originate from the HCl produced by the decomposition of FeCl3.At 650 °C, a synergistic inhibitory effect on H2S was observed, which intensified with an increased proportion of Fe2O3.Specifically, when Fe2O3 and FeCl3 were combined at ratios of 1:2, 1:1, and 2:1, the actual release was 0.3%, 0.6%, and 1.1% lower than the theoretical predictive value, respectively.It is possible that the oxidation reaction of organic sulfur by Fe2O3 competes with the reaction between HCl and organic sulfur, In contrast to the combination of CaO with Fe-based conditioners, Figure 3g-i demonstrate that the composite of Fe 2 O 3 and FeCl 3 induced a synergistic promotion effect on H 2 S release between approximately 350 and 550 • C.This effect is attributed to the fact that at lower temperatures, both Fe 2 O 3 and FeCl 3 enhance the release of H 2 S, with FeCl 3 having a particularly significant impact (as depicted in Figure 2).Notably, Figure 3i reveals that the combination of CaO and FeCl 3 at a 1:2 ratio exhibited a more pronounced synergistic promotion effect compared to other composite ratios.This again indicates that the promotional effect on H 2 S release may originate from the HCl produced by the decomposition of FeCl 3 .At 650 • C, a synergistic inhibitory effect on H 2 S was observed, which intensified with an increased proportion of Fe 2 O 3 .Specifically, when Fe 2 O 3 and FeCl 3 were combined at ratios of 1:2, 1:1, and 2:1, the actual release was 0.3%, 0.6%, and 1.1% lower than the theoretical predictive value, respectively.It is possible that the oxidation reaction of organic sulfur by Fe 2 O 3 competes with the reaction between HCl and organic sulfur, leading to a reduction in the negative impact of HCl.
The synergistic effects of composite conditioners on H 2 S release, as depicted in Figure 4, are primarily manifested as synergistic suppression within the 350~450 • C temperature range for the combination of CaO and FeCl 3 , and at 650 • C for the combination of Fe 2 O 3 and FeCl 3 .The synergistic inhibitory effect observed with the composite of CaO and FeCl 3 , as inferred from Figure 3, is attributed to the strong alkalinity of CaO neutralizing the HCl generated by the decomposition of FeCl 3 .This neutralization effectively prevents HCl from engaging in reactions with inorganic or organic sulfur compounds presented in the sludge, thus suppressing the production of H 2 S. At 550 • C, only the RS-CaO-FeCl 3 composite at a ratio of 2:1 exhibited a minor synergistic inhibitory effect on H 2 S release.However, as the proportion of FeCl 3 increased, a synergistic promotion effect was observed, potentially due to the elevated Fe content facilitating sintering reactions that form Ca-Fe compounds.At 650 • C, the composite of Fe 2 O 3 and FeCl 3 alone demonstrated a synergistic inhibitory effect on H 2 S release, which may be attributed to the competitive reaction between the oxidation of organic sulfur by Fe 2 O 3 and the reaction of HCl with organic sulfur at high temperatures, which could potentially reduce the negative impact of HCl.Despite the presence of Cl not being conducive to the suppression of H 2 S release, the sulfur-fixing capacity of Fe at high temperatures appears to override this effect.In conclusion, the selection of the composite of CaO and FeCl 3 for the 350~450 • C range, the CaO and FeCl 3 composite at a 2:1 ratio for 550 • C, and the Fe 2 O 3 and FeCl 3 composite for 650 • C was suggested to achieve a synergistic inhibitory effect on H 2 S release during sludge pyrolysis.
range for the combination of CaO and FeCl3, and at 650 °C for the combination of Fe2O3 and FeCl3.The synergistic inhibitory effect observed with the composite of CaO and FeCl3, as inferred from Figure 3, is attributed to the strong alkalinity of CaO neutralizing the HCl generated by the decomposition of FeCl3.This neutralization effectively prevents HCl from engaging in reactions with inorganic or organic sulfur compounds presented in the sludge, thus suppressing the production of H2S.At 550 °C, only the RS-CaO-FeCl3 composite at a ratio of 2:1 exhibited a minor synergistic inhibitory effect on H2S release.However, as the proportion of FeCl3 increased, a synergistic promotion effect was observed, potentially due to the elevated Fe content facilitating sintering reactions that form Ca-Fe compounds.At 650 °C, the composite of Fe2O3 and FeCl3 alone demonstrated a synergistic inhibitory effect on H2S release, which may be attributed to the competitive reaction between the oxidation of organic sulfur by Fe2O3 and the reaction of HCl with organic sulfur at high temperatures, which could potentially reduce the negative impact of HCl.Despite the presence of Cl not being conducive to the suppression of H2S release, the sulfur-fixing capacity of Fe at high temperatures appears to override this effect.In conclusion, the selection of the composite of CaO and FeCl3 for the 350~450 °C range, the CaO and FeCl3 composite at a 2:1 ratio for 550 °C, and the Fe2O3 and FeCl3 composite for 650 °C was suggested to achieve a synergistic inhibitory effect on H2S release during sludge pyrolysis.

Effect of Single Conditioner on Sulfur Species
In order to investigate the mechanism of sulfur fixation in the char by various conditioners, considering that the inhibitory effect of the conditioner on H2S release is most pronounced at 650 °C, XPS was employed to examine the changes in sulfur-containing functional groups within the RS and the char obtained from pyrolysis at 650 °C. Figure 5a-e present the S 2p spectral profiles for both the sludge and the resultant pyrolysis char.Figure 5f displays the relative percentages of different sulfur species to the total sulfur content before pyrolysis.The sulfur in RS was distributed as inorganic sulfates (23.0%), sulfones (36.6%), sulfoxides (5.5%), aromatic sulfur (17.5%), aliphatic sulfur (14.8%), and inorganic sulfides (2.6%).Upon pyrolysis of RS, the levels of inorganic sulfates, sulfones, sulfoxides, and inorganic sulfides exhibited negligible variation (<1.3%), signifying their high stability.Conversely, the proportions of aliphatic and aromatic sulfur compounds were reduced to 7.2% and 10.8%, respectively, reflecting an overall decrease of 14.8%.Given that 10.0% of the sulfur was released as H2S during the pyrolysis of RS, as depicted in Figure 2, this suggests that H2S is predominantly derived from the decomposition of aliphatic and aromatic sulfur compounds [18].
In comparison to RS-char, the RS-CaO-char exhibited a reduction in the concentrations of aromatic and aliphatic sulfur by 6.4% and 2.7%, respectively.This reduction suggests that CaO has enhanced the decomposition or transformation of these organic sulfur species.Concurrently, there was an increase in the levels of inorganic sulfates, sulfones, and sulfoxides by 1.2%, 4.3%, and 0.3%, respectively.Upon closer examination of the chemical species, including aliphatic and aromatic sulfur (R1-S-R2), sulfoxides (R1-SO-R2), and sulfones (R1-SO2-R2), it was deduced that CaO acted as a catalyst, promoting the conversion of organic sulfur into more stable, oxidized forms.This conversion reduced the likelihood of these species being converted into gas-S during pyrolysis.Furthermore, the

Effect of Conditioners on Sulfur Species in Char 2.3.1. Effect of Single Conditioner on Sulfur Species
In order to investigate the mechanism of sulfur fixation in the char by various conditioners, considering that the inhibitory effect of the conditioner on H 2 S release is most pronounced at 650 • C, XPS was employed to examine the changes in sulfurcontaining functional groups within the RS and the char obtained from pyrolysis at 650 • C. Figure 5a-e present the S 2p spectral profiles for both the sludge and the resultant pyrolysis char.Figure 5f displays the relative percentages of different sulfur species to the total sulfur content before pyrolysis.The sulfur in RS was distributed as inorganic sulfates (23.0%), sulfones (36.6%), sulfoxides (5.5%), aromatic sulfur (17.5%), aliphatic sulfur (14.8%), and inorganic sulfides (2.6%).Upon pyrolysis of RS, the levels of inorganic sulfates, sulfones, sulfoxides, and inorganic sulfides exhibited negligible variation (<1.3%), signifying their high stability.Conversely, the proportions of aliphatic and aromatic sulfur compounds were reduced to 7.2% and 10.8%, respectively, reflecting an overall decrease of 14.8%.Given that 10.0% of the sulfur was released as H 2 S during the pyrolysis of RS, as depicted in Figure 2, this suggests that H 2 S is predominantly derived from the decomposition of aliphatic and aromatic sulfur compounds [18].
In comparison to RS-char, the RS-CaO-char exhibited a reduction in the concentrations of aromatic and aliphatic sulfur by 6.4% and 2.7%, respectively.This reduction suggests that CaO has enhanced the decomposition or transformation of these organic sulfur species.Concurrently, there was an increase in the levels of inorganic sulfates, sulfones, and sulfoxides by 1.2%, 4.3%, and 0.3%, respectively.Upon closer examination of the chemical species, including aliphatic and aromatic sulfur (R 1 -S-R 2 ), sulfoxides (R 1 -SO-R 2 ), and sulfones (R 1 -SO 2 -R 2 ), it was deduced that CaO acted as a catalyst, promoting the conversion of organic sulfur into more stable, oxidized forms.This conversion reduced the likelihood of these species being converted into gas-S during pyrolysis.Furthermore, the observed increase in inorganic sulfide content (3.4%) indicated that CaO may be involved in capturing gas-S.
6.5% increase in sulfoxides.This suggests that FeCl3 has a detrimental impact on the oxidation of organic sulfur, and its reductive properties may have prompted the conversion of sulfones to sulfoxides.The quantity of inorganic sulfides experienced a 0.5% increase.Considering that this increase in inorganic sulfides was not derived from the oxidation of other sulfur species, it is probable that FeCl3 captured gas-S and effectively sequestered the sulfur within the char.

Synergistic Effect of Composite Conditioners on Sulfur Species
To investigate the synergistic effects of composite conditioners, it has been observed that Ca-Fe conditioners exhibit a synergistic promotion effect at 650 °C, while Fe2O3-FeCl3 demonstrates a synergistic inhibition effect at the same temperature.The chars obtained from the pyrolysis of RS-CaO-Fe2O3 (1:2) and RS-Fe2O3-FeCl3 (2:1) at 650 °C were selected for analysis, considering their optimal synergistic inhibitory or promotive effects.These Within the RS-Fe 2 O 3 -char, there were respective decreases of 5.1% and 2.5% in the levels of aromatic and aliphatic sulfur compounds, respectively, which aligns with the trend observed in the RS-CaO-char, albeit with a less pronounced effect.Concurrently, there was an increase of 1.5% in inorganic sulfates and a 5.5% increase in the concentrations of sulfones.Meanwhile, the concentration of sulfoxides declined by 0.3%.It is hypothesized that Fe 2 O 3 shares a comparable role with CaO in facilitating the generation of oxidized sulfur species.Due to its more potent oxidative capacity, Fe 2 O 3 was capable of yielding an increased quantity of sulfones [19].Nevertheless, a modest increase of only 1.0% was observed in inorganic sulfide, which is below the 3.4% escalation achieved with CaO.On the one hand, this is because the conditioner has strong basicity that can capture acidic sulfur-containing gases to form inorganic sulfide, as indicated by the XRD analysis.However, Fe 2 O 3 has a lower basicity compared to CaO, thus its ability to capture gas-S is relatively weaker.
Compared to RS-char, the levels of aliphatic and aromatic sulfur in RS-FeCl 3 -char increased by 1.3% and 1.2%, respectively.This indicates that FeCl 3 suppressed their decomposition.Concurrently, there was a 7.2% reduction in sulfones, contrasting with a 6.5% increase in sulfoxides.This suggests that FeCl 3 has a detrimental impact on the oxidation of organic sulfur, and its reductive properties may have prompted the conversion of sulfones to sulfoxides.The quantity of inorganic sulfides experienced a 0.5% increase.Considering that this increase in inorganic sulfides was not derived from the oxidation of other sulfur species, it is probable that FeCl 3 captured gas-S and effectively sequestered the sulfur within the char.

Synergistic Effect of Composite Conditioners on Sulfur Species
To investigate the synergistic effects of composite conditioners, it has been observed that Ca-Fe conditioners exhibit a synergistic promotion effect at 650 • C, while Fe 2 O 3 -FeCl 3 demonstrates a synergistic inhibition effect at the same temperature.The chars obtained from the pyrolysis of RS-CaO-Fe 2 O 3 (1:2) and RS-Fe 2 O 3 -FeCl 3 (2:1) at 650 • C were selected for analysis, considering their optimal synergistic inhibitory or promotive effects.These residues were subjected to XPS analysis, with the resulting S 2p peaks depicted in Figure 6a,b.The percentage composition of various sulfur species relative to the total sulfur content prior to pyrolysis is illustrated in Figure 6c,d.
In the instance of the RS-Fe2O3-FeCl3 (2:1) composite, as shown in Figure 6d, the differences between the experimental and theoretical values for sulfones and sulfoxides were negligible, indicating that the combination of Fe2O3 and FeCl3 maintains a strong oxidative effect on the conversion of aromatic and aliphatic sulfur species into these compounds.Nonetheless, the measured values for aromatic and aliphatic sulfur were increased by 4.5% and 3.4%, respectively, when contrasted with the theoretical values.This corroborates the phenomenon observed in Figure 3g, where the actual release of H2S is subjugated to theoretical estimates, implying that the composite of Fe2O3 and FeCl3 suppresses the decomposition of aromatic and aliphatic sulfur species, thereby reducing H2S release.This is further supported by the analysis presented in Figure 4.

Sulfur-Containing Mineral Components
To further clarify whether the Ca-Fe composite conditioners sinter at high temperatures to produce Ca-Fe compounds, and to reveal the mechanism behind the increased presence of inorganic sulfates and inorganic sulfides in the char as depicted in Figure 5, In the case of the RS-CaO-Fe 2 O 3 (1:2) composite, as depicted in Figure 6c, the measured sulfone content was observed to be 6.5% less than the predicted theoretical value.The levels of aromatic and aliphatic sulfur were 3.9% and 2.2% above the theoretical estimates, respectively.This suggests that the combination of CaO and Fe 2 O 3 hinders the oxidation of aromatic and aliphatic sulfur into sulfones, which is detrimental to the reduction in H 2 S emissions.Moreover, the actual measured quantity of inorganic sulfides was 1.4% less than the expected value, indicating that the CaO and Fe 2 O 3 composite has a reduced capability to capture gas-S.These findings align with the analysis shown in Figure 3, positing that at high temperatures, the interaction between CaO and Fe 2 O 3 , potentially forming Ca-Fe compounds, reduces their oxidative impact on organic sulfur compounds and their capacity to capture gas-S.
In the instance of the RS-Fe 2 O 3 -FeCl 3 (2:1) composite, as shown in Figure 6d, the differences between the experimental and theoretical values for sulfones and sulfoxides were negligible, indicating that the combination of Fe 2 O 3 and FeCl 3 maintains a strong oxidative effect on the conversion of aromatic and aliphatic sulfur species into these compounds.Nonetheless, the measured values for aromatic and aliphatic sulfur were increased by 4.5% and 3.4%, respectively, when contrasted with the theoretical values.This corroborates the phenomenon observed in Figure 3g, where the actual release of H 2 S is subjugated to theoretical estimates, implying that the composite of Fe 2 O 3 and FeCl 3 suppresses the decomposition of aromatic and aliphatic sulfur species, thereby reducing H 2 S release.This is further supported by the analysis presented in Figure 4.

Sulfur-Containing Mineral Components
To further clarify whether the Ca-Fe composite conditioners sinter at high temperatures to produce Ca-Fe compounds, and to reveal the mechanism behind the increased presence of inorganic sulfates and inorganic sulfides in the char as depicted in Figure 5, an analysis of the mineral components of the pyrolysis samples was conducted using XRD. Figure 7a displays the XRD spectra of the sludge and char obtained at 650 • C. A comparison between RS-char and RS-CaO-char revealed distinct peaks corresponding to CaSO 4 and CaS in RS-CaO-char, which were absent in RS-char.This observation confirms that CaO facilitates the retention of sulfur as inorganic sulfates and inorganic sulfides within the char.As a result, the sulfur content in char (char-S) increases, while the sulfur in gaseous phase (gas-S) decreases, in accordance with the data presented in Table 1.Additionally, the identified forms of inorganic sulfates and inorganic sulfides, specifically CaSO 4 and CaS, are believed to be the consequence of emitted SO 2 and H 2 S being captured by CaO.Similarly, the presence of FeSO 4 and FeS in RS-Fe 2 O 3 and RS-FeCl 3 indicates that Fe-based conditioners exhibit a sulfur-fixing reaction similar to that of CaO.Both Fe-based and Cabased conditioners effectively immobilize sulfur by capturing gas-S and forming inorganic sulfates and sulfides within the char, as depicted in Figure 5.
in gaseous phase (gas-S) decreases, in accordance with the data presented in Table 1.Additionally, the identified forms of inorganic sulfates and inorganic sulfides, specifically CaSO4 and CaS, are believed to be the consequence of emitted SO2 and H2S being captured by CaO.Similarly, the presence of FeSO4 and FeS in RS-Fe2O3 and RS-FeCl3 indicates that Fe-based conditioners exhibit a sulfur-fixing reaction similar to that of CaO.Both Fe-based and Ca-based conditioners effectively immobilize sulfur by capturing gas-S and forming inorganic sulfates and sulfides within the char, as depicted in Figure 5.
The XRD spectra of the solid-phase products resulting from the pyrolysis of composite-conditioned sludge are depicted in Figure 7b.There are peaks corresponding to CaSO4, FeSO4, and FeS within the char of composite-conditioned sludge, identical to those observed in Figure 7a.This indicates that the composite conditioners are capable of sulfur fixation through the direct capture of gas-S.However, it is noteworthy that when CaO was combined with Fe2O3, the presence of FeCa2O4 substance peaks was detected in the char of RS-CaO-Fe2O3 obtained at 650 °C.These peaks were not observed in the char of RS-CaO-FeCl3 obtained at 450 °C, nor in the char of the singly conditioned sludge (as shown in Figure 7a).This finding confirms that the reaction between Ca-based and Febased conditioners at high temperatures leads to the formation of Ca-Fe compounds.As a result of this reaction, their capacity to capture gaseous sulfur is reduced, which in turn contributes to an increased release of H2S.

Sample Preparation
In this study, the RS was collected from the Xinkaipu wastewater treatment plant located in Changsha, Hunan.The RS was first dried at 105 °C until a constant weight was achieved.Subsequently, it was ground and sieved to obtain a particle size of ≤80 mesh [23].The processed samples were then stored in a light-protected environment for subsequent use.In accordance with the standards "GB/T28731-2012" and "GB/T31391-2015" [24,25], both the proximate and ultimate analyses (Elementar Vario EL, Hanau, Germany) of the RS were conducted, respectively, with the results detailed in Table 2.The XRD spectra of the solid-phase products resulting from the pyrolysis of compositeconditioned sludge are depicted in Figure 7b.There are peaks corresponding to CaSO 4 , FeSO 4 , and FeS within the char of composite-conditioned sludge, identical to those observed in Figure 7a.This indicates that the composite conditioners are capable of sulfur fixation through the direct capture of gas-S.However, it is noteworthy that when CaO was combined with Fe 2 O 3 , the presence of FeCa 2 O 4 substance peaks was detected in the char of RS-CaO-Fe 2 O 3 obtained at 650 • C.These peaks were not observed in the char of RS-CaO-FeCl 3 obtained at 450 • C, nor in the char of the singly conditioned sludge (as shown in Figure 7a).This finding confirms that the reaction between Ca-based and Fe-based conditioners at high temperatures leads to the formation of Ca-Fe compounds.As a result of this reaction, their capacity to capture gaseous sulfur is reduced, which in turn contributes to an increased release of H 2 S.

Sample Preparation
In this study, the RS was collected from the Xinkaipu wastewater treatment plant located in Changsha, Hunan.The RS was first dried at 105 • C until a constant weight was achieved.Subsequently, it was ground and sieved to obtain a particle size of ≤80 mesh [23].The processed samples were then stored in a light-protected environment for subsequent use.In accordance with the standards "GB/T28731-2012" and "GB/T31391-2015" [24,25], both the proximate and ultimate analyses (Elementar Vario EL, Hanau, Germany) of the RS were conducted, respectively, with the results detailed in Table 2.The reagents CaO, Fe 2 O 3 , and FeCl 3 utilized in this study were all obtained from Sinopharm Chemical Reagent Co., Ltd.(Shanghai, China).The conditioners were mixed with the RS in a dry state [26], using a mass ratio of 10:1 for RS to conditioner [15].The sludge samples amended with CaO, Fe 2 O 3 , and FeCl 3 were designated as RS-CaO, RS-Fe 2 O 3 , and RS-FeCl 3 , respectively.The composite conditioners were prepared at mixing ratios of 1:1, 2:1, and 1:2.The samples of sludge conditioned with the composite additives were denoted as RS-A-B (R), where 'A' and 'B' represent the respective conditioners, and 'R' indicates the mixing ratio.For example, RS-CaO-Fe 2 O 3 (1:1) referred to the sludge treated with a 1:1 mixture of CaO and Fe 2 O 3 conditioner.The resulting chars from the pyrolysis of different sludge samples are abbreviated as X-char, with X representing the specific sludge type.

Pyrolysis Experiment
Sludge pyrolysis experiments were performed using a horizontal tube furnace in a controlled experimental setup, which is consistent with that of our group's previous study [27,28].Each trial involved the pyrolysis of 1 g of sludge, carried out under a nitrogen atmosphere with a flow rate of 200 NmL/min.The experiments were conducted over a temperature range from 350 to 700 • C, with each run lasting for a period of 20 min [14].After the tubular furnace reached the preset temperature for the pyrolysis reaction, the sample was quickly inserted into the center of the heating tube.Gaseous products were collected using gas collection bags.After the reaction, the char was cooled to room temperature under a nitrogen atmosphere before being collected for further analysis [29].

Analytic Methods
The content of sulfur in both the RS and the derived pyrolysis char was determined using an elemental analyzer.The presence of inorganic crystalline sulfur-containing phases in the RS and char was investigated using an X-ray diffractometer (XRD, Rigaku Ultima IV, CuKa, Japan) with scanning angles ranging from 5 • to 90 • .The XRD data were analyzed using Jade 6 software, with reference to the PDF-2 (Powder Diffraction File) database.Additionally, the chemical speciation of sulfur in the RS and char was analyzed using an Xray photoelectron spectrometer (XPS, Thermo Scientific K-Alpha, Waltham, MA, USA) with an aluminum anode operating at 12 kV and 6 mA.The sulfur species were identified based on their binding energies and classified into inorganic sulfates (170 ± 0.3 eV), sulfones (168.2 ± 0.3 eV), sulfoxides (166 ± 0.3 eV), aromatic sulfur (164.1 ± 0.3 eV), aliphatic sulfur (163.3 ± 0.3 eV), and inorganic sulfides (162.2 ± 0.3 eV) [14,30].The quantification of sulfur-containing gases was performed using a gas chromatograph (GC, HC-3, Wuhan, China).This GC system incorporates a dual-column arrangement designed to efficiently separate a spectrum of sulfur-containing gaseous compounds.The detection capabilities are highly sensitive, with limits as low as 0.1 ppm, facilitated by a flame photometric detector.Prior to ignition, the outlet pressures of the hydrogen (H 2 ) and oxygen (O 2 ) regulators were set to 0.1 MPa.Additionally, the H 2 and O 2 pressures were adjusted on the instrument panel to 0.03 MPa.Once the column and detector reached the necessary temperatures, ignition could proceed.The set temperatures for columns 1 and 2 were 92.5 • C and 46.8 • C, respectively.

Calculation Method
The percentage of different forms of sulfur in the solid phase to total sulfur before pyrolysis was denoted as P S from char , and calculated using Equation (2).
where S C was the total sulfur content in char; S A was the percentage of the peak area corresponding to the sulfur compound 'A' in the XPS spectrum, relative to the total peak area; S total was the total sulfur content in the sludge before pyrolysis.The percentage of sulfur in various forms in the gas phase relative to the total sulfur content before pyrolysis, was denoted as P S from gas .This value was calculated using Equation (3), with H 2 S serving as an example: where P S from H2S is the percentage of H 2 S relative to the total sulfur content before pyrolysis; M H2S is the ratio of the molar mass of sulfur atoms to the molar mass of H 2 S molecules; C H2S is the concentration of H 2 S in the gas phase; and V is the volume of H 2 S. The theoretical yield of sulfur-containing products in both gas and solid phases, derived from the pyrolysis of composite-conditioned sludge, was denoted as Y Theo , and calculated using Equation ( 4), with the theoretical release of H 2 S serving as an example: where Y 1 and Y 2 are the release amounts of H 2 S when conditioners 1 and 2 were used individually to treat the sludge, respectively; x 1 and x 2 are the percentages of conditioners 1 and 2 in the composite conditioner, respectively.The synergistic effect value, which quantified the composite conditioner's ability to suppress the release of H 2 S during the sludge pyrolysis, was calculated using Equation (5).
where Y Exp and Y Theo correspond to the actual and theoretical release amounts of H 2 S, respectively.A negative S ynergistic effect value indicates that the combination of the two conditioners induced a synergistic suppression effect on the release of H 2 S during pyrolysis.Conversely, a positive S ynergistic effect value suggests that the combination facilitated the emission of H 2 S.

Conclusions
This study clarified the effects of three conditioners (CaO, Fe 2 O 3 , and FeCl 3 ) on the sulfur distribution within the products of sludge pyrolysis.By conducting a comparative analysis of the theoretical and experimental values of sulfur-containing substances in the products, the synergistic effects of composite conditioners and their influence on the emission of sulfur-containing gases were explored.The derived conclusions are as follows: (1) The release of H 2 S was suppressed by CaO, Fe 2 O 3 , and FeCl 3 by 35.8%, 23.2%, and 9.1% at 650 • C, respectively.CaO mitigated gas-S release by promoting the transformation of organic sulfur into more stable oxidized forms, and by capturing gas-S.Fe 2 O 3 demonstrated enhanced oxidizing capabilities, while FeCl 3 inhibited the decomposition of organic sulfur and captured gas-S at high temperatures.(2) Utilizing a composite of CaO and FeCl 3 within the temperature range from 350 to 450 • C, along with a composite of Fe 2 O 3 and FeCl 3 at 650 Future research should focus on examining the impact of complex conditioners on the kinetics of pyrolysis and delve into the molecular level to explore the mechanism of sulfur fixation.To enhance the optimization of the dewatering, conditioning, and pyrolysis process, an economic assessment and comparative analysis of various pathways will be essential.

Figure 1 .
Figure 1.Distribution of sulfur in gaseous products.(Red represents H2S, orange represents C yellow represents SO2, green represents CH3SH, and blue represents CS2).

Figure 1 .
Figure 1.Distribution of sulfur in gaseous products.(Red represents H 2 S, orange represents COS, yellow represents SO 2 , green represents CH 3 SH, and blue represents CS 2 ).

Figure 4 .
Figure 4.The synergistic effect of composite conditioners in suppressing the release of H2S during sludge pyrolysis.

Figure 4 .
Figure 4.The synergistic effect of composite conditioners in suppressing the release of H 2 S during sludge pyrolysis.

Table 1 .
The distribution of sulfur among various products.

Table 1 .
The distribution of sulfur among various products.

Table 2 .
Proximate and ultimate analysis of RS.
• C, can synergistically suppress the H 2 S release.Conversely, between 350 • C and 550 • C, the combination of Fe 2 O 3 with FeCl 3 , and between approximately 550 and 650 • C, the composite of Ca-based and Fe-based conditioners, demonstrate a synergistic enhancement effect on the release of H 2 S. (3) In composite conditioning, the strong alkalinity of CaO neutralizes HCl, an acidic gas generated by the decomposition of FeCl 3 .This neutralization prevents HCl from interacting with inorganic or organic sulfides in the sludge, thus synergistically inhibiting H 2 S release.At 450 • C, this synergistic effect inhibits H 2 S release by 56.3%.Nonetheless, the formation of FeCa 2 O 4 above 550 • C, reduces the sulfur-fixing capacity of the composite conditioners, and at 650 • C, it synergistically promotes the release of H 2 S by 26.3%.