High Fidelity Hydroelastic Analysis Using Modal Matrix Reduction

: Structural assessment is a main concern when designing and operating any sort of offshore structure. This assessment is meant to ensure that the structural integrity is preserved along the lifespan of the asset, withstanding the worst sea-states that will be encountered and making sure that the accumulated fatigue damage will not jeopardize its structural integrity neither. The purpose of this paper is to present a fast and reliable hydroelastic model. This model is based on time-domain tight-coupling of a three-dimensional FEM (ﬁnite element method) linear structural model and a three-dimensional FEM seakeeping hydrodynamics model. In order to reduce the computational cost of structural dynamic simulations, the high-ﬁdelity structural solution is projected onto the modal basis to obtain the modal matrix system and to extend the response amplitude operators (RAO) to the modal responses (MRAO). From there, the number of structural degrees of freedom can be greatly reduced by retaining only those eigenmodes preserving most of the structural elastic energy. The use MRAOs and/or the large reduction in structural degrees of freedom allows us to: ﬁrst, quickly analyse the large number of loadcases required on the design stage; and second, to implement a digital twin for structural health monitoring in operational conditions. The paper also presents an application case of the developed methodology.


Introduction
Hydroelasticity is a hot topic in naval architecture, and marine and offshore engineering. The numerical analysis of the hydro-elastic response of a ship or offshore platform requires the coupling between the seakeeping hydrodynamics and the structural dynamics.
Looking at the literature, the most common approach is to model seakeeping hydrodynamics, solving the wave diffraction-radiation problem using a three-dimensional boundary element method (BEM) in the frequency domain and modelling the structural problem using a one-dimensional beam model solved by the finite element method (FEM) [1][2][3][4][5][6]. Several works have extended the seakeeping hydrodynamic model solving the Navier-Stokes equation instead of using potential flow [7][8][9]. The Navier-Stokes solvers, despite being quite a bit more expensive computationally speaking, are recommended for those fluid structure interaction problems where potential flow solver cannot properly capture the physics of the problem under analysis. This is the case of severe wave conditions with high non-linear effects, such as slamming and green waters. In this regard, some of the most recent works are [10,11], where a two-way coupling is developed and applied to the S175 containership under severe wave conditions to analyse the before-mentioned effects.
From the structural point of view, only a few authors have moved to more sophisticated FEM models, such as the one-dimensional-three-dimensional FEM [3,6], quasi-static approximations, or direct coupling with a three-dimensional FEM model [12]. Most of these works only look at the linear response, and the most common approach for the structural dynamics is the modal superposition considering a very limited number of modes [12][13][14]. However, in order to be able to simulate transient and/or non-linear responses, it is necessary to directly solve in the time-domain [13].
To simulate transient or non-linear responses, Cummins [15] proposed an impulse response function to transfer frequency domain results into the time-domain, and different authors have followed this approach [1,2,6,14]. This method requires, first, to carry out the modal analysis, and, second, to solve the radiation problem for each displacement mode. In case a large number of modes are to be considered, the computational effort greatly increases. A shortcoming of this approach is that it is not capable of capturing local stresses, which is mandatory to predict structural failure [16]. To overcome this shortcoming, it is necessary to solve the three-dimensional fully coupled hydroelastic problem in the timedomain. However, this approach is quite rare in the literature due to its complexity and high computational cost. In [17], the present authors implemented a partitioned strategy to analyse the interaction of the free surface with the seals of a surface affect ship. The hydrodynamic model was based on potential flow with forward speed, and the results were validated against experimental tests. In [5], the hydroelastic response of a S175 ship using BEM-FEM coupling was compared, the results against the equivalent rigid body solution were presented.
One of the most recent works in hydroelasticity using potential flow for seakeeping hydrodynamics was published by the present authors in [18]. In that work, a tightly coupled hydroelastic model was developed within SeaFEM (a time-domain wave diffractionradiation solver based on FEM [19][20][21]). A comparison between iterative and monolithic coupling is carried out, as well as a comparison between loose (weak, one-way) and tight (strong, two-way) coupling. It was concluded that monolithic coupling is the most robust (from the numerical stability). In any case, the computational cost is still too high and is mostly taken by the structural dynamics solver. The governing equations of the hydroelastic problem are those of the wave diffraction-radiation problem in the time domain, along with the linear structural equations solved with FEM [18]. The coupling is carried out at the wet surface of the floater, where the seakeeping hydrodynamics solver (SeaFEM) sends pressure values to the structural solver, and the latter sends back the structural displacements on the same surface. The time variation of the structural displacements along the surface normal direction are imposed as a normal velocity boundary condition on the wet surface (see Figure 1).
Mahérault et al. [22] proposed, also, to use the modal approximation for calculating the fatigue damage of ULCS due to springing. The hydroelastic model is based on a three-dimensional structural BEM and a three-dimensional seakeeping BEM. In that work, the total structural solution is separated into a quasi-static solution, accounting for the hydrodynamic pressure under rigid body motion, and a dynamic solution, accounting for low frequency modes. This separation was used to avoid a solution convergence problem when using the modal basis. However, limiting the modal solution to the lower frequency modes is only valid when the elastic energy is mostly concentrated in those modes, which is not the general case.
The present work can be seen as an evolution of [18] to reduce the computational time of the structural solver (which is the dominant one). This reduction is achieved by projecting the high-fidelity structural solution onto the modal basis to obtain the modal matrix system. The structural model is also tightly coupled with the time-domain wave diffraction-radiation solver SeaFEM. Since SeaFEM is based on the FEM, the mesh used for the wet body boundary condition might have the same or similar discretization to the structural mesh to ensure no loss of accuracy for local modes. In those cases where the local modes are not excited, different mesh discretization can be used with no interpolation issues, as reported in [18]. As shown in the application example of this work, no modal converges issues have been detected when using the approximation presented here. Mahérault et al. [22] proposed, also, to use the modal approximation for calculating the fatigue damage of ULCS due to springing. The hydroelastic model is based on a threedimensional structural BEM and a three-dimensional seakeeping BEM. In that work, the total structural solution is separated into a quasi-static solution, accounting for the hydrodynamic pressure under rigid body motion, and a dynamic solution, accounting for low frequency modes. This separation was used to avoid a solution convergence problem when using the modal basis. However, limiting the modal solution to the lower frequency modes is only valid when the elastic energy is mostly concentrated in those modes, which is not the general case.
The present work can be seen as an evolution of [18] to reduce the computational time of the structural solver (which is the dominant one). This reduction is achieved by projecting the high-fidelity structural solution onto the modal basis to obtain the modal matrix system. The structural model is also tightly coupled with the time-domain wave diffraction-radiation solver SeaFEM. Since SeaFEM is based on the FEM, the mesh used for the wet body boundary condition might have the same or similar discretization to the structural mesh to ensure no loss of accuracy for local modes. In those cases where the local modes are not excited, different mesh discretization can be used with no interpolation issues, as reported in [18]. As shown in the application example of this work, no modal converges issues have been detected when using the approximation presented here.

Structural Model Order Reduction
In [18], it was concluded that the three-dimensional fully coupled hydroelastic problem in the time-domain is very expensive computationally speaking, and most of the computational work is taken by the structural solver. Hence, in this work, a modal order reduction is proposed for the structural problem, aiming at reducing the computational cost of fully coupled simulations.

Structural Model Order Reduction
In [18], it was concluded that the three-dimensional fully coupled hydroelastic problem in the time-domain is very expensive computationally speaking, and most of the computational work is taken by the structural solver. Hence, in this work, a modal order reduction is proposed for the structural problem, aiming at reducing the computational cost of fully coupled simulations.
The main idea underlying this work is to accurately approximate the high-fidelity FEM solution to the structural problem by projecting the FEM solution onto a subspace of solutions with a dimension number (number of degrees of freedom) several orders of magnitudes smaller than the FEM solution. The subspace of solution is built using the modal matrix reduction (MMR) technique, where the projection subspace is built with the basis of vectors obtained from modal analysis.
The high-fidelity FEM solution can be expressed as: where u(x, t), is the nodal displacements vector of the structure, a i (x) are the vectors of the modal basis, and q i (t) temporal variations of the modal amplitudes. The modal basis is obtained from the eigenvalue problem: where M and K are the structural mass and stiffness matrices obtained via FEM. Additionally, the eigenvalue problem is: where; λ i = ω 2 i is the eigenvalue of matrix M −1 K associated to eigenvector a i , and ω i is the modal frequency. For the modal basis, the following relations hold: Form this point on, it is assumed that eigenvectors a i are normalized with respect to M (|a i | = 1). In the general case, the governing equation of structural dynamics is: (6) where; C is a damping matrix, and f(t) is the external loads vector. Introducing Equation (1) into Equation (6), the following holds: where; A = a 1 , a 2 . . . a N FEM and q = [q i ]. Multiplying Equation (7) by A T , the diagonal modal matrix system is obtained: ..
where; c i = A T CA i is the modal damping, and f i (t) = a T i f(t). For the sake of simplicity, the modal damping c i will be modelled as a fraction ξ i of the critical damping, c i = 2ξ i ω i . Then, we obtain: ..
Equation (9) is a second-order ordinary differential equation, representing the dynamics of each structural mode. In the context of this work, this equation will be solved numerically using the same scheme used by SeaFEM for the rigid body motion. This is a Newmark scheme with coefficients γ = 1 2 and β = 1 4 [21]. The modal elastic energy will be used to identify those modes most excited. The modal elastic energy is given by:

Hydroelastic Model
The hydroelastic model proposed in this work consists of coupling a time-domain wave diffraction-radiation solver with a time-domain structural solver, as was previously performed by the authors in [18]. The main difference in this work is that, instead of using the full FEM structural solver, the reduced structural model based on MMR will be used.
Using this approach, the number of degrees of freedom can be reduced by several order of magnitudes while still preserving an accurate structural solution. This is achieved by considering only modes excited by the external loads. Doing so, the computational time of the structural problem (and the hydroelastic problem) can be greatly reduced, so that dynamic hydroelastic simulations in the time-domain can be affordable from a computational point of view.
If the hydroelastic problem is assumed to be linear (linear structural model and linear external loads), it is possible to compute modal response amplitude operators (MRAOs), as is usually performed for the six rigid body degrees of freedom. Obtaining the MRAOs allows to pre-calculate the structural response offline, and use them to obtain the structural response under specific scenarios with no need of solving the hydroelastic problem again (see Figure 2). The linearization of the problem obtaining MRAOs can be also used to identify those modes that will be most excited under specific scenarios, and only those will be used to compute the structural response.
that dynamic hydroelastic simulations in the time-domain can be affordable from a computational point of view.
If the hydroelastic problem is assumed to be linear (linear structural model and linear external loads), it is possible to compute modal response amplitude operators (MRAOs), as is usually performed for the six rigid body degrees of freedom. Obtaining the MRAOs allows to pre-calculate the structural response offline, and use them to obtain the structural response under specific scenarios with no need of solving the hydroelastic problem again (see Figure 2). The linearization of the problem obtaining MRAOs can be also used to identify those modes that will be most excited under specific scenarios, and only those will be used to compute the structural response. This approach is suitable to be used in operative conditions where there is little time for computation and, also, to estimate long-term response. For instance, it facilitates the calculation of the accumulated fatigue damage throughout the lifespan of the structure given the environmental scenarios, and their probability, the structure will encounter.
The aforementioned approach requires carrying out a modal analysis of the structure. In order to use the MRAOs offline, a number of hydroelastic analysis must be precomputed to obtain the MRAOs under different wave directions and frequencies. This offline extra effort will be compensated by the ease for estimating long-term responses and, also, if the number of load cases to be analysed is large enough.

Buoy Model Definition
For the sake of simplicity, in order to demonstrate and understand the present hydroelastic approach, it is applied to a floating buoy made of steel. This results in a simple structure with a not too large number of degrees of freedom, where it is cheaper to compute the structural modes. Then, analysis such as energy distribution across structural modes is easier to show and understand.
The described hydroelastic model with reduced structural model using MMR is applied to a floating buoy model to verify its accuracy. Figure 3 shows the buoy's main dimensions. This approach is suitable to be used in operative conditions where there is little time for computation and, also, to estimate long-term response. For instance, it facilitates the calculation of the accumulated fatigue damage throughout the lifespan of the structure given the environmental scenarios, and their probability, the structure will encounter.
The aforementioned approach requires carrying out a modal analysis of the structure. In order to use the MRAOs offline, a number of hydroelastic analysis must be precomputed to obtain the MRAOs under different wave directions and frequencies. This offline extra effort will be compensated by the ease for estimating long-term responses and, also, if the number of load cases to be analysed is large enough.

Buoy Model Definition
For the sake of simplicity, in order to demonstrate and understand the present hydroelastic approach, it is applied to a floating buoy made of steel. This results in a simple structure with a not too large number of degrees of freedom, where it is cheaper to compute the structural modes. Then, analysis such as energy distribution across structural modes is easier to show and understand.
The described hydroelastic model with reduced structural model using MMR is applied to a floating buoy model to verify its accuracy. Figure 3 shows the buoy's main dimensions. The buoy is made of steel plates, resulting on a stiff structure. It is moored, and the fairlead point is located at the intersection of the vertical centre line and the lowest surface. Decay tests have been carried out using SeaFEM to find out the natural periods. Viscous damping for surge, sway, roll, and pitch have been estimated as 5% of the critical ones. The buoy and mooring particulars are given in Table 1. Table 2 provides the particulars of the structural FEM model, and Figure 4 shows the FEM mesh used for the structural part. The buoy is made of steel plates, resulting on a stiff structure. It is moored, and the fairlead point is located at the intersection of the vertical centre line and the lowest surface.
Decay tests have been carried out using SeaFEM to find out the natural periods. Viscous damping for surge, sway, roll, and pitch have been estimated as 5% of the critical ones. The buoy and mooring particulars are given in Table 1. Table 2 provides the particulars of the structural FEM model, and Figure 4 shows the FEM mesh used for the structural part.

Modal Analysis
The first step to implement the MMR technique is to carry out the modal analysis of the corresponding structure. For the buoy with no restrictions, the total number of elastic modes is equal to the number of degrees of freedom minus the six rigid body degrees of freedom. In order to solve the eigenvalue problem, the Intel MKL library has been used. It allowed us to compute 11,311 elastic modes, which represent over 90% of the total elastic modes. The corresponding modal frequencies range from 85.97 Hz to over 34.14 MHz.

Modal Analysis
The first step to implement the MMR technique is to carry out the modal analysis of the corresponding structure. For the buoy with no restrictions, the total number of elastic modes is equal to the number of degrees of freedom minus the six rigid body degrees of freedom. In order to solve the eigenvalue problem, the Intel MKL library has been used. It allowed us to compute 11,311 elastic modes, which represent over 90% of the total elastic modes. The corresponding modal frequencies range from 85.97 Hz to over 34.14 MHz.

Equilibrium Load Case
As a first load case, the buoy is considered to be in equilibrium, subject to the selfweight, hydrostatic pressure, and the mooring vertical force. This loadcase is computed using the classic FEM computation and using the MMR technique. Figure 5 shows how elastic energy is distributed across modes. Table 3 provides the values of the most energetic modes. Figure 6 shows the normalized displacements field of the most energetic modes. Figure 7 shows the cumulative energy after ordering the modes from most to least energetic. Only Eigenmode 75 contains over 35% of the total elastic energy, the 17 most energetic eigenmodes retain over 90%, only 54 modes are necessary to retain 95% of the elastic energy, and 474 are necessary to retain 99%.       Figure 8 compares the vertical displacement field using the MMR approximation different sizes of the modal basis, as well as the direct FEM solution. It is observed h even using only 17 modes (retaining 90% of the elastic energy), the displacement field quite close to the one obtained by the FEM solution. As the size of the modal basis creases, the solution is better approximated. A modal basis, retaining 99% of energy, lows a reduction in the number of degrees of freedom of the system from 12,462 to 4 which means a 96.2% reduction.   Figure 8 compares the vertical displacement field using the MMR approximation for different sizes of the modal basis, as well as the direct FEM solution. It is observed how even using only 17 modes (retaining 90% of the elastic energy), the displacement field is quite close to the one obtained by the FEM solution. As the size of the modal basis increases, the solution is better approximated. A modal basis, retaining 99% of energy, allows a reduction in the number of degrees of freedom of the system from 12,462 to 474, which means a 96.2% reduction.  Figure 8 compares the vertical displacement field using the MMR approximation for different sizes of the modal basis, as well as the direct FEM solution. It is observed how even using only 17 modes (retaining 90% of the elastic energy), the displacement field is quite close to the one obtained by the FEM solution. As the size of the modal basis increases, the solution is better approximated. A modal basis, retaining 99% of energy, allows a reduction in the number of degrees of freedom of the system from 12,462 to 474, which means a 96.2% reduction.

Dynamic Load Case: Irregular Waves Response
Next, the hydroelastic response of the buoy under the actions of dynamic loads due to waves is presented. The hydroelastic response is obtained using a strong (tight) coupling between the seakeeping hydrodynamics and the structural dynamics. Then, the hydrodynamics pressure over the wet surface of the buoy is sent to the MMR model, and the MMR sent back the structural displacements to be imposed on the wet surface. Hence, added mass and damping due to wave radiation, as well as increase in stiffness due to hydrostatic pressure, are taken into account. An iterative scheme ensures the convergence of both, hydrodynamic pressure and structural displacements, before moving to the next time step. The time stepping and iterative schemes used in the partitioned scheme are the ones used in [18], but using the MMR solver instead of the FEM solver. Table 4 provides the particular of the SeaFEM model and the scenario to be calculated, and Figure 9 shows the computational domain used. to waves is presented. The hydroelastic response is obtained using a strong (tight) co pling between the seakeeping hydrodynamics and the structural dynamics. Then, the h drodynamics pressure over the wet surface of the buoy is sent to the MMR model, and MMR sent back the structural displacements to be imposed on the wet surface. Hen added mass and damping due to wave radiation, as well as increase in stiffness due hydrostatic pressure, are taken into account. An iterative scheme ensures the convergen of both, hydrodynamic pressure and structural displacements, before moving to the n time step. The time stepping and iterative schemes used in the partitioned scheme are ones used in [18], but using the MMR solver instead of the FEM solver. Table 4 provid the particular of the SeaFEM model and the scenario to be calculated, and Figure 9 sho the computational domain used.  First, the hydroelastic response of the buoy under monochromatic waves (MRAO is obtained. For this purpose, a white noise spectrum with wave periods between 0.1 Hz and 1 Hz is used. Figure 10 shows the MRAOs obtained for some relevant eigenmod It is observed that a local maximum happens for the heave natural frequency. The mo response for a specific wave scenario is automatically obtained by multiplying the MRA and the wave amplitudes. Then, for a specific eigenmode m, a realization for the mo amplitude is quickly obtained by: where; q si the modal amplitude obtained for the static equilibrium case, A and are the amplitude and frequency of the i wave, α is the modal phase delay resp First, the hydroelastic response of the buoy under monochromatic waves (MRAOs) is obtained. For this purpose, a white noise spectrum with wave periods between 0.143 Hz and 1 Hz is used. Figure 10 shows the MRAOs obtained for some relevant eigenmodes. It is observed that a local maximum happens for the heave natural frequency. The modal response for a specific wave scenario is automatically obtained by multiplying the MRAOs and the wave amplitudes. Then, for a specific eigenmode m, a realization for the modal amplitude is quickly obtained by: where; q eq si the modal amplitude obtained for the static equilibrium case, A i and Ω i are the amplitude and frequency of the i th wave, α mi is the modal phase delay respect to the i th wave, and δ i is a random phase to generate a realization of an irregular sea-wave spectrum.
to the i wave, and δ is a random phase to generate a realization of an irregular seawave spectrum. The average modal energy during a long realization can be obtained as: where; E , = ω q is the static contribution of the equilibrium state, and E , = ω ∑ (MRAO · A ) is the dynamic contribution. For the dynamic contribution, we can define the Modal Energy Response Amplitude Operator (MERAO) as: which is an indicator of how much structural energy is induced by a monochromatic wave. Figure 11 shows the MERAO for the wave frequencies analysed. From this information, it is extracted that most elastic energy is absorbed by a number of eigenmodes much smaller than the total number of degrees of freedom.  The average modal energy during a long realization can be obtained as: where; E m,s = 1 2 ω 2 m q 2 eq is the static contribution of the equilibrium state, and E m,d = (MRAO i ·A i ) 2 is the dynamic contribution. For the dynamic contribution, we can define the Modal Energy Response Amplitude Operator (MERAO) as: which is an indicator of how much structural energy is induced by a monochromatic wave. Figure 11 shows the MERAO for the wave frequencies analysed. From this information, it is extracted that most elastic energy is absorbed by a number of eigenmodes much smaller than the total number of degrees of freedom. to the i wave, and δ is a random phase to generate a realization of an irregular seawave spectrum. The average modal energy during a long realization can be obtained as: where; E , = ω q is the static contribution of the equilibrium state, and E , = ω ∑ (MRAO · A ) is the dynamic contribution. For the dynamic contribution, we can define the Modal Energy Response Amplitude Operator (MERAO) as: which is an indicator of how much structural energy is induced by a monochromatic wave. Figure 11 shows the MERAO for the wave frequencies analysed. From this information, it is extracted that most elastic energy is absorbed by a number of eigenmodes much smaller than the total number of degrees of freedom.  Second, the irregular waves are generated using a Jonswap spectrum (Table 5 and Figure 12). The number of waves used for the discretization is 19, the minimum wave period is 1 s (w max = 6.283 rad/s), and the maximum wave period is 7 s (w min = 0.897 rad/s). The frequency interval is then ∆w = 0.283 rad/s. For each wave, instead of using the centre value of the frequency interval, the wave frequency has been selected randomly within the interval in order to avoid short term wave field repeatability. Second, the irregular waves are generated using a Jonswap spectrum (Table 5 and Figure 12). The number of waves used for the discretization is 19, the minimum wave period is 1 s (wmax = 6.283 rad/s), and the maximum wave period is 7 s (wmin = 0.897 rad/s). The frequency interval is then ∆w = 0.283 rad/s. For each wave, instead of using the centre value of the frequency interval, the wave frequency has been selected randomly within the interval in order to avoid short term wave field repeatability.   Given the MRAOs and a specific wave scenario, the structural energy response is easily obtained, and most energetic modes can be identified. Using Equation (11), a realization of the modal responses can be quickly obtained. Then, the structural displacement field can be computed by linear combination of the eigenmodes, and stresses can be calculated using the constitutive model equation (e.g., linear elasticity).
One realization has been carried out for the Jonswap spectrum given in Table 5. Then, the instantaneous modal amplitude and modal energy have been computed for all eigenmodes. Figure 13 provides the instantaneous elastic energy computed as the sum of the elastic energy of all structural eigenmodes. It is observed that the structural energy changes considerably. Since combining the structural response at every time step for all eigenmodes can become very expensive computationally speaking, most energetic time steps can be selected as representative of the most critical ones, reducing this way the number of calculations to carried out. Figure 14 provides the energy distribution averaged over the simulated time, and the instantaneous energy distribution for time = 120.628 s, where the elastic energy reaches its maximum. It is observed that the energy distribution is quite similar. Figure 15 provides the cumulative energy when ordering eigenmodes from most to least average energy. As it was shown in the static case, the number of eigenmodes retaining most of the structural energy is small compared to the total number of degrees of freedom. Given the MRAOs and a specific wave scenario, the structural energy response is easily obtained, and most energetic modes can be identified. Using Equation (11), a realization of the modal responses can be quickly obtained. Then, the structural displacement field can be computed by linear combination of the eigenmodes, and stresses can be calculated using the constitutive model equation (e.g., linear elasticity).
One realization has been carried out for the Jonswap spectrum given in Table 5. Then, the instantaneous modal amplitude and modal energy have been computed for all eigenmodes. Figure 13 provides the instantaneous elastic energy computed as the sum of the elastic energy of all structural eigenmodes. It is observed that the structural energy changes considerably. Since combining the structural response at every time step for all eigenmodes can become very expensive computationally speaking, most energetic time steps can be selected as representative of the most critical ones, reducing this way the number of calculations to carried out. Figure 14 provides the energy distribution averaged over the simulated time, and the instantaneous energy distribution for time = 120.628 s, where the elastic energy reaches its maximum. It is observed that the energy distribution is quite similar. Figure 15 provides the cumulative energy when ordering eigenmodes from most to least average energy. As it was shown in the static case, the number of eigenmodes retaining most of the structural energy is small compared to the total number of degrees of freedom.

Conclusions
This work presents a methodology for hydroelastic analysis of floating structures This methodology is based on a reduced order model of the structural dynamics, usin the modal matrix reduction (MMR) techniques, tightly coupled with a seakeeping hydro dynamics solver (SeaFEM). The methodology has been applied to a buoy, showing that large reduction in the number of structural degrees of freedom (with respect to a FEM solver) can be achieved when projecting on the modal basis and retaining most energeti modes. This reduction justifies the computational effort of computing the modal basis vi the eigenmode analysis.
When working under linear loads, modal response amplitude operators (MRAOs can be obtained. This allows for analysing a large number of different loadcases ver quickly once MRAOS have been obtained offline, which justifies the effort of obtaining th MRAOs.
The present methodology can be used, for instance, to assess the fatigue damage o an asset during the design stage. Once MRAOs have been obtained, given the differen environmental scenarios and their probability along its lifespan, the structural respons can be quickly obtained for each scenario.
The linear analysis can be also used to identify the most energetic eigenmodes unde specific scenarios, leading to a reduction in the number of degrees of freedom. This reduc tion can be used not just to quickly obtain the structural response by linear combinatio of the modal responses, but also to create a reduced modal basis to be used under non linear external loads (such as those coming from mooring systems and wind turbines Hence, this is very suitable to be implemented in digital twins for structural health mon toring purposes, where assuming linear loads allows to obtain instant results, and simu lations under non-linear loads can be carried out much faster (due to the reduction o degrees of freedom) than computing the dynamic case of a structural FEM solver couple to a seakeeping solver.

Conclusions
This work presents a methodology for hydroelastic analysis of floating structures. This methodology is based on a reduced order model of the structural dynamics, using the modal matrix reduction (MMR) techniques, tightly coupled with a seakeeping hydrodynamics solver (SeaFEM). The methodology has been applied to a buoy, showing that a large reduction in the number of structural degrees of freedom (with respect to a FEM solver) can be achieved when projecting on the modal basis and retaining most energetic modes. This reduction justifies the computational effort of computing the modal basis via the eigenmode analysis.
When working under linear loads, modal response amplitude operators (MRAOs) can be obtained. This allows for analysing a large number of different loadcases very quickly once MRAOS have been obtained offline, which justifies the effort of obtaining the MRAOs.
The present methodology can be used, for instance, to assess the fatigue damage of an asset during the design stage. Once MRAOs have been obtained, given the different environmental scenarios and their probability along its lifespan, the structural response can be quickly obtained for each scenario.
The linear analysis can be also used to identify the most energetic eigenmodes under specific scenarios, leading to a reduction in the number of degrees of freedom. This reduction can be used not just to quickly obtain the structural response by linear combination of the modal responses, but also to create a reduced modal basis to be used under non-linear external loads (such as those coming from mooring systems and wind turbines). Hence, this is very suitable to be implemented in digital twins for structural health monitoring purposes, where assuming linear loads allows to obtain instant results, and simulations under non-linear loads can be carried out much faster (due to the reduction of degrees of freedom) than computing the dynamic case of a structural FEM solver coupled to a seakeeping solver.
The authors have shown, only for demonstration purposes, how an energy criterion can be used for the selection of modes. The proper level of reduction can be formulated in terms of the elastic energy retained, leading to a significant reduction, even for high levels of energy retention. However, other criteria could be used. Additionally, the level of reduction achieved will depend on the specific problem to deal with. For instance, if the model is applied for a local analysis on one specific location of the structure. In that case, the selection of those modes that most contribute to that specific location will result in a larger reduction than if details are to be preserved all over the structure.