Abstract
Surface texture influences friction and transfer layer formation during sliding. In the present paper three well-defined surface textures, namely unidirectional, 8-ground, and random, were employed on steel plates. Experiments were conducted on a tribological couple – zinc pin against steel plate – using an inclined pin-on-plate sliding tester. It was observed that the occurrence of stick-slip motion, the transfer layer formation and the value of coefficient of friction as well as its two components, namely adhesion and plowing, depend primarily on surface texture. The effect of surface texture on coefficient of friction was attributed to the variation of the plowing component of friction for different surfaces. The plowing component of friction was highest for the surface texture that promotes plane strain conditions while it was lowest for the texture that favors plane stress conditions at the interface. Dimensionless quantifiable roughness parameters were formulated to describe the degree of plowing and hence the plane strain/stress type deformations taking place at the asperity level.
References
[1] C.M.Wichern, B.C.De Cooman, C.J.Van Tyne: J. Mater. Process. Technol.160(2005)278.10.1016/j.jmatprotec.2004.06.017Search in Google Scholar
[2] M.R.Lovell, Z.Deng: Tribol. Int.35(2002)85.10.1016/S0301-679X(01)00097-4Search in Google Scholar
[3] Y.A.-H.Mashal, M.H.El-Axir, M.A.Kassem: Wear250(2001)518.10.1016/S0043-1648(01)00602-0Search in Google Scholar
[4] C.Hamdullah, B.Hasan: Tribol. Int.37(2004)433.10.1017/S1049096504004615Search in Google Scholar
[5] D.O.Bello, S.Walton: Tribol. Int.20(1987)59.10.1016/0301-679X(87)90091-0Search in Google Scholar
[6] W.Rasp, C.M.Wichern: J. Mater. Process. Technol.25–126(2002)379.10.1016/S0924-0136(02)00346-1Search in Google Scholar
[7] P.K.Saha, W.R.D.Wilson, R.S.Timsit: Wear197(1996)123.10.1016/0043-1648(95)06881-3Search in Google Scholar
[8] E.Schedin: Wear179(1994)123.10.1016/0043-1648(94)90229-1Search in Google Scholar
[9] H.E.Staph, P.M.Ku, H.J.Carper: Mechanism and machine theory8(1973)197.10.1016/0094-114X(73)90053-0Search in Google Scholar
[10] Y.Xie, J.A.Williams: Wear196(1996)21.10.1016/0043-1648(95)06830-9Search in Google Scholar
[11] P.L.Menezes, Kishore, S.V.Kailas: ASME: J. Tribol.128(2006)697.10.1115/1.2345401Search in Google Scholar
[12] S.Malayappan, R.Narayanasamy: Int. J. Adv. Manuf. Technol.23(2004)636.10.1007/s00170-003-1584-3Search in Google Scholar
[13] R.Lakshmipathy, R.Sagar: Int. J. Mach. Tools Manufact.32(1992)685.10.1016/0890-6955(92)90023-ASearch in Google Scholar
[14] A.Määttä, P.Vuoristo, T.Mäntylä: Tribol. Int.34(2001)779.10.1016/S0301-679X(01)00074-3Search in Google Scholar
[15] Z.M.Hu, T.A.Dean: Int. J. Mach. Tools Manufact.40(2000)1637.10.1016/S0890-6955(00)00014-6Search in Google Scholar
[16] E.S.Gadelmawla, M.M.Koura, T.M.A.Maksoud, I.M.Elewa, H.H.Soliman: J. Mater. Process. Technol.123(2002)133.10.1016/S0924-0136(02)00060-2Search in Google Scholar
[17] W.Wieleba: Wear252(2002)719.10.1016/S0043-1648(02)00029-7Search in Google Scholar
[18] N.O.Myers: Wear5(1962)182.10.1016/0043-1648(62)90002-9Search in Google Scholar
[19] R.Singh, S.N.Melkote, F.Hashimoto: Wear258(2005)1500.10.1016/j.wear.2004.03.071Search in Google Scholar
[20] T.Hisakado: Journal of Mechanical Engineering Science20(1978)247.10.1243/JMES_JOUR_1978_020_044_02Search in Google Scholar
[21] Y.-R.Jeng: Tribol. Trans.33(1990)402.10.1080/10402009008981970Search in Google Scholar
[22] J.Lundberg: Tribol. Int.28(1995)317.10.1016/0301-679X(94)00003-9Search in Google Scholar
[23] W.Hirst, A.E.Hollander: Proc. R. Soc. London, Ser. A337(1974)379.10.1098/rspa.1974.0056Search in Google Scholar
[24] F.P.Bowden, D.Tabor: The Friction and Lubrication of Solids, Clarendon, Oxford(1954).Search in Google Scholar
[25] S.Bouissou, J.P.Petit, M.Barquins: Wear214(1998)156.10.1016/S0043-1648(97)00242-1Search in Google Scholar
[26] D.H.Hwang, K.H.Zum Gahr: Wear255(2003)365.10.1016/S0043-1648(03)00063-2Search in Google Scholar
[27] I.Nieminen, P.Andersson, K.Holmberg: Wear130(1989)167.10.1016/0043-1648(89)90230-5Search in Google Scholar
[28] Y.Xie, H.M.Hawthorne: Wear240(2000)65.10.1016/S0043-1648(00)00336-7Search in Google Scholar
[29] V.Jardret, H.Zahouani, J.L.Loubet, T.G.Mathia: Wear218(1998)8.10.1016/S0043-1648(98)00200-2Search in Google Scholar
[30] L.Y.Wang, Z.F.Yin, J.Zhang, C.Chen, S.Hsu: Wear237(2000)155.10.1016/S0043-1648(99)00312-9Search in Google Scholar
[31] Z.Liu, J.Sun, W.Shen: Tribol. Int.35(2002)511.10.1016/S0301-679X(02)00046-4Search in Google Scholar
[32] J.Feder: Fractals, Plenum Press, New York(1988).10.1007/978-1-4899-2124-6Search in Google Scholar
[33] M.Hasegawa, J.Liu, K.Okuda, M.Nunobiki: Wear192(1996)40.10.1016/0043-1648(95)06768-XSearch in Google Scholar
[34] J.M.Challen, P.L.B.Oxley: Wear52(1979)22910.1016/0043-1648(79)90080-2Search in Google Scholar
[35] H.Petryk: Proceedings of the Institution of Mechanical Engineers International Conference: Tribology-Friction, Lubrication and Wear – 50 Years On; 2 (1987)987.Search in Google Scholar
[36] T.E.Fischer, S.Bhattacharya, R.Salher: Tribol. Trans.31(1988)442.10.1080/10402008808981846Search in Google Scholar
[37] B.J.Hamrock, D.Dowson: Ball Bearing Lubrication, John Willey and Sons, New York, USA(1981).Search in Google Scholar
[38] A.Faulkner, R.D.Arnell: Wear242(2000)114.10.1016/S0043-1648(00)00406-3Search in Google Scholar
[39] S.V.Kailas, P.L.Menezes: Proceedings of International Seminar on Metal Forming – Process Design and Optimization, Indian Institute of Science, India (2003)124.Search in Google Scholar
[40] P.L.Menezes, Kishore, S.V.Kailas: Tribol. Int.39(2006)175.10.1016/j.triboint.2005.04.009Search in Google Scholar
[41] K.Tanaka, T.Kato, Y.Matsumoto: ASME: J. Tribol.125(2003)587.10.1115/1.1538194Search in Google Scholar
[42] G.Subhash, W.Zhang: Wear252(2002)123.10.1016/S0043-1648(01)00852-3Search in Google Scholar
[43] P.Sahoo, S.K.R.Chowdhury: Wear253(2002)924.10.1016/S0043-1648(02)00243-0Search in Google Scholar
[44] F.-X.Wang, P.Lacey, R.S.Gates, S.M.Hsu: ASME: J. Tribol.113(1991)755.10.1115/1.2920689Search in Google Scholar
[45] N.Yoshioka: Tectonophysics277(1997)29.10.1016/S0040-1951(97)00076-0Search in Google Scholar
[46] K.Varadi, Z.Neder, K.Friedrich: Wear200(1996)55.Search in Google Scholar
© 2008, Carl Hanser Verlag, München
