Theoretical Prediction of Thermophysical Properties of Waste Beef Tallow Biodiesel

In this present study, simple linear equations were developed for predicting the thermo-physical properties of beef tallow biodiesel by considering their molecular weight and number of double bonds as two independent variables. Interestingly, molecular weight signiﬁes as a function of carbon chain length and number of carbon molecules in it whereas numbers of double bond signiﬁes the degree of unsaturation.


INTRODUCTION
The demand for biodiesel is growing widely in both developed and developing countries to meet their increasing energy demand in a sustainable way.Biodiesel is the common name for any fatty acid alkyl ester produced by transesterifying fatty acids in triglyceride molecule present in animal fat or vegetable oil, with short chained alcohol in presence of catalyst under optimized condition.Especially, it is widely known for its fair advantages like non-toxicity, high biodegradability, enhanced engine performance with reduced engine parts wear and emissions; thereby making it a self-sustaining and environmental friendly biofuel [1].In fact, biodiesel is superior to diesel fuel in terms of its reduced CO and NOx emission, higher sustainability and lower impact on environment.
In general, the quality of biodiesel is decided by its thermo-physical properties which are in turn reflected in its performance, combustion and emission (PCE) characteristics during engine application [2].Density (ρ), kinematic viscosity (ν), cetane number (CN) and higher heating value (HHV) are the important thermo-physical properties which signify the quality of biodiesel and have very good influence during its combustion [3].
Supporting this, density of the biodiesel influences its fuel mass to be injected inside the cylinder and serves as a precursor for regulating the fuel injection system to induce complete combustion [4].Also, it is regarded as a salient feature for designing biodiesel reactors, separation units, plumbing and storage tanks [5].Furthermore, density of the biodiesel is entirely dependent on its characterized FAEs and their degree of unsaturation [6].Likewise, viscosity of biodiesel defines about its spray characteristics and atomization upon injection inside the cylinder [7].Thus, biodiesel with low viscosity denies sufficient lubrication necessary for precise fitting in fuel injection pumps which results in leakage or component wear [8].Contrarily, biodiesel with high viscosity leads to poor atomization due to formation of large droplets upon injection followed by incomplete combustion resulting in increased deposition of carbon content (in case of highly unsaturated biodiesel), which induces polymerization reaction [9].Like density, viscosity of biodiesel are also completely influenced by its FAEs in addition to their degree of unsaturation [10].
Besides, cetane number is a dimensionless fuel property of biodiesel which serves as an indicator in defining its ignition delay, which in turn explains about the premixed and diffusion combustion during power stroke [11].And then, it also decides the heat release profile; combustion noise and emission characteristics of the biodiesel, thereby accrediting it as the most influential parameter to be determined for all diesel fuels [12,13].Apparently, higher CNs were noted for long chain saturated biodiesel than compared to short or unsaturated biodiesel [14]; thus, implying the significance of chain length and unsaturation in deciding the cetane number of biodiesel.Further, higher heating value of biodiesel characterizes its probable energy content available in it [15] and always occurs lesser than diesel fuel due to the presence of oxygen and absence of sulphur content in it.In consequence of reduced HHV, more amount of biodiesel will be consumed to produce equivalent work output derived from diesel fuel, thereby resulting in reduced overall engine performance and increased fuel consumption [2].Like other properties, HHV is also deeply influenced by the FAEs profile and their degree of unsaturation in the biodiesel; and tends to be lower for biodiesel with unsaturated FAEs.
Considering their significance in deciding the quality of biodiesel, these properties must be always evaluated with reference to permissible standards, to ensure its compatibility with CI engines.Inspite of their significance, these properties are evaluated occasionally due to various technical challenges like insufficient availability of test samples and time consumption apart from the necessity to strictly adhere to standard protocols, making it complex and exhaustive.However, this can be over ruled by developing mathematical correlations to predict these vital properties instead of exhaustive experimental process.Eventually, this approach is highly useful in predicting the theoretical values of these properties and can be developed by correlating various factors associated to the biodiesel.As a matter of fact, it was clearly evident that these properties are deeply influenced by the characteristics of individual FAEs and their extensive molecular properties [16].Accordingly, numerous studies have been carried out with an aim of developing prediction models and mathematical correlations for evaluating the properties of biodiesel using the structural properties of their FAEs.
Beginning with, Knothe, 2005 proposed in his study that the properties of biodiesel were highly dependent on their fatty acid alkyl esters, which in turn depended on the structural features of fatty acid chain and their alcohol moiety.Furthermore, the study strongly concluded that biodiesel properties like viscosity, lubricity, CN, oxidative stability, cold flow, HHV and exhaust emissions were entirely dependent on their fatty acids alkyl esters.In addition, properties like viscosity, melting point, cetane number and HHV increased with increasing carbon chain length while decreased with increase in degree of unsaturation [3].
Among the studies related to the theoretical prediction, Pratas et al., 2010 predicted the density and viscosity of fatty acid alkyl esters theoretically by developing predictive models with temperature as a variable and comparing them with experimental values.For the purpose of study, eight methyl esters and seven ethyl esters were measured for their density and viscosity at different atmospheric pressure and temperature (273.15 to 363.15 K).Predications made for density using GCVOL method was found to be highly reliable with only <1% deviation for fatty acid methyl esters (FAMEs) and 1.5% deviation for fatty acid ethyl esters (FAEEs).Similarly, in case of predicting viscosity, Ceriani and Meirelles (CM) method was found to be highly effective than Marreiro and Gani (MG) method in view of their minimal deviation in their experimental and predicted result by 4.53% for FAMEs and 7.92% for FAEEs [17].Likewise, similar study predicted the density and viscosity of FAMEs by establishing simple correlations using their composition (in %wt.).Eventually, these correlations predicted the density with an accuracy of 98.5% while viscosity for 97.1%; and guaranteed for the prediction of these physical properties for any biodiesel by simply using their FAME compositions.In conclusion, the mean predicted value for density was found between 861.7-885.7 kg/m 3 and viscosity was found between 4.31-5.64mm 2 /s [18].
Likewise, Freitas et al., 2010 attempted for evaluating the predictive models for determining the viscosity of biodiesel theoretically.Subsequently, predictive models based on Krisnangkura's, Ceriani's, Yuan's proposed and revised models were evaluated for their predictive capability.Ultimately, the results yielded an average deviation of 4.65%, 5.34%, 7.25% and 8.07% for revised Yuan's model followed by Yuan's model, Krisnangkura's model and Ceriani's model respectively and were verified in accordance with viscosity for biodiesel blended diesel fuels.Therefore, this study strongly recommended revised Yuan's model as an effective predictive model for determining the viscosity of biodiesel theoretically [7].Another way, Roosta and Bardool, 2019 developed three predictive models for determining the viscosity of biodiesel by correlating 226 data points (viscosity at various temperatures ranging between 263.15 and 373.15 K) corresponding to 16 different fatty acid methyl esters (FAMEs).Starting with, first model employed temperature as a variable and it demonstrated minimal average absolute relative deviation (AARD) of 0.97%.And then, second model was developed by considering number of carbon atoms and number of double bonds in ester molecules as two independent variables; and exhibited a minimal AARD of 2.28%.Finally, the third model was established using the molar average of viscosity of FAMEs along with their availabilities; by correlating 185 data points (viscosity at various temperatures ranging between 263.15 and 373.15 K) corresponding to 23 different FAMEs.Eventually, the minimal AARD was recorded as 2.96%; and was found to be highly reliable for predicting the viscosity of biodiesel theoretically [19].
Besides, Giakoumis and Sarakatsanis, 2019 reviewed 16 predictive models developed for theoretically predicting the CN using the structural features of fatty acid alkyl esters like carbon chain length, molecular weight, number of double bonds and degree of unsaturation.This study used experimental data related to cetane number and fatty acid composition referenced from nearly 50 literatures and coefficient of determination as effective tool in deciding the most effective predictive model.In specific, this study strongly recommended the predictive model developed by Giakoumis and Sarakatsanis in view of their high accuracy and predictive capability.However, this study also concluded that increasing number of variables like chain length, molecular weight and degree of unsaturation in predictive models resulted in lower accuracy results [12].
In addition to this, Hong et al., 2015 developed two empirical correlations for determining HHV of fatty acid methyl esters (FAMEs) and fatty acid ethyl esters (FAEEs) by employing molecular weight and number of unsaturated double bonds as independent variables.In fact, this study proposed that HHV was directly proportional to molecular weight and inversely proportional to degree of unsaturation in the ester molecules.Moreover, the constants in the developed equations were found to be higher for molecular weight, in case of FAEEs and higher for double bonds, in case of FAMEs.Thus, it can be strongly concluded that the HHV of biodiesel was strongly influenced by the molecular weight of FAEs and above all, the effect of molecular weight and number of unsaturated double bonds was found to be more on FAEEs than FAMEs [20].
In this present paper, simple yet reliable linear equations were developed for predicting the thermophysical properties (density, kinematic viscosity, cetane number and higher heating value) of biodiesel from waste beef tallow by considering the molecular weight and number of double bonds in their characterized FAEs as two independent variables.Eventually, molecular weight serves as an indicator for length and number of carbon atoms in the ester molecules while numbers of double bond signifies its degree of unsaturation.The developed correlations were evaluated for their absolute deviation and % error by comparing the theoretical values with experimental thermo-physical data for waste beef tallow biodiesel along with other ethanol based biodiesel referenced from existing literatures.

Sample Collection
Waste beef tallow was rendered from fleshing and subcutaneous wastes collected from leather tanneries and animal slaughter houses respectively.Beginning with, the collected wastes were autoclaved @ 120 °C, 2 bar pressure to separate tallow from non-fatty organic wastes [21].The rendered tallow was washed with water at 60 °C to remove any solid sediment and dehydrated at 110 °C to remove any moisture content from it.Following this, the tallow was degummed by treating it with orthophosphoric acid under continuous heating with intermittent stirring as carried out by Srinivasan et al., 2018 [22], to remove phospholipids from it.Later on, the refined tallow was preserved using refrigeration to avoid any contamination and prevent rancdification (oxidation of tallow).

Preparation of beef tallow biodiesel
The refined tallow was subjected for base catalyzed transesterification using ethanol as solvent.Hence, the tallow was transesterified into ethyl tallow biodiesel by maintaining the reaction parameters as follows: oil to ethanol molar ratio -1:6; catalyst concentrationpotassium hydroxide (KOH) of 0.5% wt. of tallow taken; reaction temperature -60 o C, reaction duration -120 minutes [2].Post completion of reaction, the mixture was separated in separating funnel under the influence of gravity which separated biodiesel layer at top and glycerol at bottom.The separated biodiesel was water washed repeatedly and dehydrated to remove any impurities and moisture content, respectively, in it.

Quantification of Fatty Acid Esters (FAEs)
Starting with, the fatty acid ethyl esters (FAEs) in the tallow biodiesel were quantified using Gas Chromatography and Mass Spectrometry (GC-MS).Accordingly, FAEs were identified by the peak obtained at their corresponding retention time and were quantified based on the area occupied by those peaks.Following this, the quantified FAEs were considered for the purpose of developing empirical correlations for the thermo-physical properties.Technical specifications of GC-MS equipment have been presented in table 1 [2].

Experimental evaluation of thermo-physical properties
Necessary physico-chemical properties like density, kinematic viscosity, cetane number and higher heating value were determined as per ASTM standards to assess the quality of tallow biodiesel.Hence, the density of biodiesel was determined based on ASTM D1298 method using hydrometer whereas the kinematic viscosity of biodiesel was determined using calibrated glass-viscosity tube mentioned as per ASTM D445 method.Similarly, cetane number of biodiesel was determined as per ASTM D613 method whereas higher (gross) heating value was determined using bomb calorimeter by as per ASTM D240 method.Simultaneously, these experimental values were used to compare with theoretical values calculated using the correlations and analyse the average % error and deviation between them.
Likewise, thermo-physical properties for characterized FAEs used in calculations were referenced from standard literatures corresponding to biodiesel quality, standards and properties determined as per ASTM standards [3,23].Accordingly, four sets of data series were developed for each thermo-physical property and comprised of consolidated values of corresponding property for different FAEs.Later on, these data series were used in developing the correlations for predicting the thermo-physical properties.

Mathematical Modelling of Empirical Correlations
The thermo-physical properties of beef tallow biodiesel were evaluated theoretically, by developing empirical correlations using the data series using DESIGN-EXPERT software.Accordingly, the molecular weight (MW E ) and number of double bond present in fatty acid chain (N E ) of individual ester molecule were considered as input variables, while their corresponding value in the data series were taken as output variable.Following this, mathematical correlation for each thermophysical property was developed by fitting the variations in the values of that property for different molecular weight and degree of unsaturation linearly by means of statistical regression [19,24].Thus, four different mathematical correlations (Eq.1-4) dedicated for Density, Kinematic Viscosity, Cetane Number and Higher Heating Value) were developed for prediction purposes.Here, N E was taken as zero for saturated FAEs; and as one, two, so on for unsaturated FAEs depending on their degree of unsaturation.

Density
Numerous studies have proposed that thermo-physical properties of any biodiesel can be evaluated theoretically by considering mole or mass fraction along with properties of individual FAEs.Here, equation 5 represents the generalized expression for determining the properties based on mass fraction whereas equation 6 represents the generalized expression for determining the properties based on mole fraction.

Y=∑
(5) where, Y is the thermo-physical property of the sample, f i is the thermo-physical property of the individual FAE, m i is mass fraction for the corresponding FAE, x i is the mole fraction of corresponding FAE determined using equation 7 by substituting the molecular weight of individual FAE along with its corresponding mass fraction.

∑ ( )
Similarly, the average absolute percentage error (AAPE) between the calculated and experimental values was determined using equation 8: where, n is the number of fatty acid esters considered for the study, f i exp and f i cal are the experimental and calculated thermo-physical properties.

Characterization and quantification of beef tallow biodiesel
Waste beef tallow biodiesel was characterized using GC spectra (figure 1), which identified the FAEs molecules along with their % availability based on retention time of the peak and area occupied by the peak respectively.In total, 10 fatty acid ethyl esters were characterized from the waste tallow biodiesel; where ethyl myristate, ethyl palmitate, ethyl oleate and ethyl stearate were identified as dominant FAEs in view of their higher availability and were expected to have an influencing role in deciding the properties of biodiesel.Table 2 summarises the preliminary data like Molecular weight, Mass and Mole fraction, Degree of unsaturation of Characterized FAEs.Based on these characterized FAEs data, molecular formula of the waste tallow biodiesel was derived as C 18 H 35 O 2 with an average molecular weight of 283.47 g/mol.

Properties of fatty acid esters (FAEs):
Apart from preliminary data, thermo-physical properties (density, kinematic viscosity, CN and HHV) of characterized FAEs along with the theoretical values determined using the mathematical correlations (Equation 1 to 4) are presented in table 3. The experimental and theoretical values were compared for Average Absolute Deviation (AAD) and Average Absolute Percentage Error (AAPE); and were found to be: 0.28 and 0.064% for density; 0.044 and 2.815% for kinematic viscosity; 1.509 and 4.77% for CN; 0.275 and 1.368% for HHV, respectively.Table 4 summarizes the absolute deviation and absolute percentage error between the reported and calculated values for individual fatty acid esters.
From table 3, properties like kinematic viscosity, CN and HHV increased with molecular weight but decreased as number of double bonds increased; meanwhile, density decreased with increasing molecular weight and reduced degree of unsaturation.Indeed, the thermo-physical properties of FAEs are entirely dependent on their molecular weight and number of double bonds signifying their degree of unsaturation [3].From equation 1, it was clearly evident that density decreased with increase in molecular weight whereas increased with increase in degree of unsaturation.The inverse proportionality between density and molecular weight is signified by the negativity of latter function and the degree of unsaturation with positive sign signified the direct proportionality.In general, density of fatty acids is inversely proportional to their corresponding number of carbon atoms; and decreases marginally for higher number of carbon atoms [24,25].Accordingly, the density of FAEs also decreased significantly for esters with lower number of carbon atoms (C8 to C12) followed by marginal decrease in density for FAEs with higher number of carbon atoms.From figure 2, the experimental values were found to be well fit with the predicted model within the 95% confidence band and can be concluded that density decreased by 1.332 kg/m 3 on average for saturated FAEs whereas decreased by 1.45 kg/m 3 on average for unsaturated FAEs.Similarly, the density of unsaturated C14:1, C16:1 and C18:1 ethyl esters were found to be 1.41%, 1.5% and 1.6% higher than the saturated C14:0, C16:0 and C18:0 ethyl esters, respectively.Eventually, the AAD and AAPE between the reported and predicted values were to be 0.28 and 0.064%, respectively.

Kinematic Viscosity:
From equation 2, it was clearly evident that kinematic viscosity increased with increase in molecular weight whereas decreased with increase in degree of unsaturation.Kinematic viscosity of FAEs was found to be directly proportional to its molecular weight and inversely proportional to its degree of unsaturation; and was demonstrated by their positive and negative sign respectively, in the equation.Based on the reported Kinematic Viscosity of fatty acid esters, it is evident that viscosity increases progressively along carbon chain length owing to the increasing Van der Waals forces along the non-polar length of the ester molecule.Eventually, this Van der Waals intermolecular attraction is a resultant of zig-zag arrangement of carbon atoms with tetrahedral bond angles along the linear fatty acid chain and occurs between SP3 hybridization atoms [24].From figure 3, the experimental values were found to be well fit with the predicted model within the 95% confidence band and can be concluded that Kinematic viscosity increased by 0.685 mm 2 /s (on average) for saturated FAEs whereas Kinematic viscosity increased by 1.02 mm 2 /s ( on average) for unsaturated FAEs.In contrast, the viscosity of unsaturated C14:1, C16:1 and C18:1 ethyl esters were found to be 18.27%, 16.3% and 18.16% lesser than the saturated C14:0, C16:0 and C18:0 ethyl ester, respectively.In fact, reduction in viscosity for these unsaturated ester molecules was as a result of weak Van der Waals intermolecular attraction caused by their CIS-Configuration, which holds back the approaching SP2 atoms (from double bond) from neighbouring molecules.Ultimately, the AAD and AAPE between the reported and predicted values were found to be 0.044 and 2.815%, respectively.

Cetane Number (CN):
From equation 3, it was clearly evident that CN increased with increase in molecular weight whereas decreased with increase in degree of unsaturation.Like kinematic viscosity, cetane number of FAE was also found to be directly proportional to its molecular weight and inversely proportional to its degree of unsaturation.Accordingly, the positive and negative sign in the equation signified its direct and inverse proportionality with the molecular weight and degree of unsaturation of FAEs.In general, CN serves as an indicator for combustion speed and ignition delay; and increases for FAEs as their molecular weight increases.From figure 4, the experimental values were found to be well fit with the predicted model within the 95% confidence band and can be noted that CN increased by 6.38 units (on average) for saturated FAEs whereas CN increased by 6.96 units (on average) for unsaturated FAEs.However, the CN of unsaturated C14:1, C16:1 and C18:1 ethyl esters were found to be 27.07%,33.68% and 25.64% lesser than the saturated C14:0, C16:0 and C18:0 ethyl esters, respectively.Moreover, the reduction in CN for unsaturated esters was accounted by their unsaturated double bonds moving towards the center of the FAE chain.Further, the AAD and AAPE between the reported and predicted values were found to be 1.509 and 4.77%, respectively.From equation 4, it was clearly evident that HHV increased with increase in molecular weight whereas decreased with increase in degree of unsaturation.The HHV of FAEs was found to be directly proportional to its molecular weight and inversely proportional to its degree of unsaturation.Supporting this, the direct proportionality was signified by the positivity of molecular weight while inverse proportionality was accounted by its degree of unsaturation.Based on the reported HHV of FAEs, it is evident that the heating value increases progressively along carbon chain length owing to the increasing number of C-H bonds, which has higher bond enthalpy.From figure 5, the experimental values were found to be well fit with the predicted model within the 95% confidence band and can be concluded that HHV increased by 0.83 MJ/kg on average for saturated FAEs whereas HHV increased by 1.9 MJ/kg on average for unsaturated FAEs.In contrast, the HHV of unsaturated C14:1, C16:1 and C18:1 ethyl esters were found to be 7%, 3.28% and 5.21% lesser than the saturated C14:0, C16:0 and C18:0 ethyl esters, respectively.This reduction in HHV for these unsaturated ester molecules is because of lesser availability of hydrogen atoms (for C-H bond) which lowers the heating value Inspite of availability of C=C bond present in fatty acid carbon chain.Taken together, the AAD and AAPE between the reported and predicted values were found to be 0.275 and 1.368%, respectively.

PROPERTIES OF BIODIESEL Density:
Density describes the amount of fuel that can be occupied with its unit volume and is altered as temperature and pressure varies proportionally.In addition, density governs the fuel injection in CI engine where large amount of fuel will be injected for same volume in case of denser fuel when compared to less denser fuel.The density of biodiesel produced from waste beef tallow was determined by measuring the mass against a known volume and was measured as 883 kg/m 3 .For waste beef tallow biodiesel, the AD in density between its experimental value and mole fraction/ mass fraction value was found to be 8.31 and 8.28, respectively whereas their APE was found to be 1.92% and 1.91%, respectively.However, upon comparing with other literatures [23,26,27], AAD in the experimental value of density from their mole fraction and mass fraction value was found to be 3.55 and 3.57, respectively whereas the AAPE for density was found to be 0.82% (mole fraction) and 0.82% (mass fraction).Table 5 summarizes the AAD and AAPE for density between experimental value, mole fraction and mass faction method values.Kinematic viscosity describes about the internal resistance to fluid's flow when gravity acts on it; and increases for biodiesel with high carbon chained FAEs.Spray characteristics of fuel like droplet size and penetration, effectiveness of atomization are deeply influenced by the kinematic viscosity and tends to produce larger droplets accompanied with poor atomization for high viscosity biodiesel, resulting in reduced combustion and increased cylinder deposits.Apart from spray characteristics, higher viscosity fuel requires more pump work which causes increased wear rate for fuel injection components thereby reducing the engine performance rate.The kinematic viscosity of biodiesel produced from waste beef tallow was determined according to ASTM D 445 specification and was calculated as 4.6 mm 2 /s, which was found to be well inside the permissible range (1.9-6 mm 2 /s).For waste beef tallow biodiesel, the AD in kinematic viscosity between its experimental value and mole fraction/mass fraction value was found to be 0.03 and 0.02 respectively whereas their APE was found to be 1.1% and 0.86%, respectively.However, upon comparing with other literatures [23,26,27], AAD in the experimental value of kinematic viscosity from their mole fraction and mass fraction value was found to be 0.12 and 0.11, respectively whereas the AAPE for kinematic viscosity was found to be 4.98% (mole fraction) and 4.48% (mass fraction).Table 6 summarizes the AAD and AAPE for kinematic viscosity between experimental value, mole fraction and mass faction method values.

Cetane Number (CN):
Cetane Number serves as an indicator for combustion speed and ignition delay; and increases for biodiesel with high saturated FAEs.Biodiesel with higher CN provide complete combustion accompanied by smooth running of engine whereas lower CN results in increased exhaust emission owing to incomplete combustion.In addition, higher CN improves the cold-start behaviour and reduces knocking and white smoke.The CN of biodiesel produced from waste beef tallow biodiesel was determined according to ASTM D613 standard and was measured as 69, which was 46.81% greater than the minimum required limit.For waste beef tallow biodiesel, the AD in CN between its experimental value and mole fraction/ mass fraction value was found to be 2.75 and 2.9, respectively whereas their APE was found to be 7.38% and 7.88%, respectively.However, upon comparing with other literatures [23,27,28], AAD in the experimental value of CN from their mole fraction and mass fraction value was found to be 2.36 and 1.9, respectively whereas the AAPE for CN was found to be 7.24% (mole fraction) and 5.87% (mass fraction).Table 7 summarizes the AAD and AAPE for CN between experimental value, mole fraction and mass faction method values.

Higher Heating Value (HHV):
Higher Heating Value of biodiesel signifies the energy content available in that biofuel and was found according to ASTM D240 specifications.Accordingly, the HHV of biodiesel produced from waste beef tallow was found to be 41 MJ/kg and was 21.09% lesser than the HHV of diesel fuel (49.65 MJ/kg) [29]; and was accounted by the presence of oxygen and absence of sulphur molecules in their esters molecule which reduced it considerably [23].For waste beef tallow biodiesel, the AD in HHV between its experimental value and mole fraction/ mass fraction value was found to be 0.04 and 0.09, respectively whereas their APE was found to be 0.20% and 0.44%, respectively.However, upon comparing with other literatures [23,27,28], AAD in the experimental value of HHV from their mole fraction and mass fraction value was found to be 0.22 and 0.24, respectively whereas the AAPE for HHV was found to be 1.08% (mole fraction) and 1.20% (mass fraction).Table 8 summarizes the AAD and AAPE for HHV between experimental value, mole fraction and mass faction method values.
Based on the study, it was evident that the thermophysical properties like density, Kinematic Viscosity, CN, HHV were entirely dependent on the properties of individual FAEs.Moreover, equation 5 (mass fraction method) clearly indicates that the major contribution in each thermo-physical property of the biodiesel were significantly contributed by ethyl myristate, ethyl palmitate, ethyl oleate and ethyl stearate available in higher concentrations than compared to other characterized FAEs.
However, these equations are limited with certain restrictions in predicting thermo-physical properties which are as follows: (i) Equations for predicting density and Kinematic Viscosity are restricted for temperatures 15 °C and 40 °C respectively, owing to development of mathematical equation based on the data series obtained at these temperatures.Equations incorporating temperature as the third variable along with the existing variables can be developed to find these properties at different temperatures.
(ii) These developed equations work well for prediction of thermo-physical properties of ethanol based biodiesel (fatty acid ethyl esters) only; and cannot be used for predicting the thermo-physical properties of other fatty acid alkyl esters (methyl, propyl and so on except ethyl).However, introducing the number of carbon atoms in alcohol moiety as a variable can help us in developing predictive models for any type of FAEs.

CONCLUSIONS
Thus, theoretical prediction of thermo-physical properties like density, kinematic viscosity, cetane number and higher heating value of waste tallow biodiesel was carried out successfully.Some of the major conclusions drawn from this computational study are as follows: (i) Thermo-physical properties of tallow and other feedstocks biodiesel were entirely dependent on their fatty acid esters profile; which in turn was influenced by the molecular weight and degree of unsaturation of these ester molecules.
(ii) Properties like kinematic viscosity, cetane number and higher heating value increased with increasing molecular weight and degree of saturation; whereas density increased for higher degree of unsaturation and reduced molecular weights.
(iii) Experimental and predicted values of the characterized FAEs in tallow biodiesel were found to be with minimal deviation and % error; which signified the accuracy in developed correlations.
(iv) Likewise, the experimental and predicted values of tallow biodiesel and other biodiesel were in good agreement with each other; along with minimal deviation between the values calculated using mole fraction and mass fraction, thereby recommending both for prediction purposes.
In conclusion, it is clearly evident that properties of any biodiesel simply depends on its FAEs profile as a function of their structural properties (molecular weight, number of double bonds).Thus, any property related to biodiesel can be easily predicted by developing correlations using these structural properties; however, introducing additional variables like temperature (for density, viscosity) and number of carbon atoms in alcohol moiety can overcome the restrictions related to the usage of these correlations for a single group of alkyl esters alone.This investigation also briefs out about the significance of FAEs in deciding the biodiesel properties, which again defines the precursors needed for choosing ideal fatty acids (direct selection or blending multiple feedstocks) for developing highly efficient sustainable biodiesel.

Figure 2 :
Figure 2 : Density of fatty acid esters as function of molecular weight

Figure 3 :
Figure 3 : Kinematic Viscosity of fatty acid esters as function of molecular weight

Figure 4 :
Figure 4: Cetane Number of fatty acid esters as function of molecular weight Higher Heating Value (HHV):

Figure 5 :
Figure 5 : Higher Heating Value of fatty acid esters as function of molecular weight

Table 2 :
Molecular weight, Mass and Mole fraction, Degree of unsaturation of Characterized FAEs

Table 3 :
Experimental and predicted thermo-physical properties of characterized FAEs

Table 4 :
Absolute Deviation (AD) and Absolute Percentage Error (APE) between experimental and predicted values for characterized FAEs

Table 5 :
Density of waste tallow and other feedstock biodiesel samples.AAD and AAPE between experimental and calculated values

Table 6 :
Kinematic Viscosity of waste tallow and other feedstock biodiesel samples.AAD and AAPE between experimental and calculated values

Table 7 :
Cetane Number of waste tallow and other feedstock biodiesel samples.AAD and AAPE between experimental and calculated values

Table 8 :
Higher Heating Value of waste tallow and other feedstock biodiesel samples.AAD and AAPE between experimental and calculated values