Skip to main content
SpringerLink
Log in

Tools with Redesigned Cutting Inserts for Intermittent Cutting

  • Published:
Russian Engineering Research Aims and scope

Abstract—The design of cutting inserts for tools used in intermittent turning is considered. As an example, it is established that a cycloid front surface of the insert is required to improve the distribution of the impact load when turning a helical rotor surface.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.

Similar content being viewed by others

REFERENCES

  1. Andreev, V.N., Borovskii, G.V., Borovskii, V.G., and Grigor’ev, S.N., Instrument dlya vysokoproizvoditel’nogo i ekologicheski chistogo rezaniya (Tools for High-Performance and Environmentally Friendly Cutting), Moscow: Mashinostroenie, 2010.

  2. Özel, T., Modeling of hard part machining: effect of insert edge preparation in CBN cutting tools, J. Mater. Process. Technol., 2003, vol. 141, no. 2, pp. 284–293.

    Article  Google Scholar 

  3. Dogra, M., Sharma, V., Sachdeva, A., and Suri, N., Tool wear, chip formation and workpiece surface issues in CBN hard turning: a review, Int. J. Precis. Eng. Manuf., 2010, vol. 11, no. 2, pp. 341–358.

    Article  Google Scholar 

  4. Ståhl, J.E., Metal Cutting. Theories and Models, Lund: SECO TOOLS, 2012.

    Google Scholar 

  5. Zhou, J., Mechanical Load Identification for Spontaneous Tool Failure Monitoring, Lund: Lund Univ., 1996.

    Google Scholar 

  6. Kudryashov, E.A., Smirnov, I.M., Yatsun, E.I., and Pavlov, E.V., Improved tools for the turning of complex surfaces, Russ. Eng. Res., 2018, vol. 38, no. 3, pp. 223–228.

    Article  Google Scholar 

  7. Kudryashov, E.A. and Smirnov, I.M., Creating rational conditions for turning surfaces of dissimilar structural materials by brittle superhard cutters, Izv. Vyssh. Uchebn. Zaved., Mashinostr., 2018, no. 2 (695), pp. 75–85.

  8. Kudryashov, E.A., Smirnov, I.M., and Khizhnyak, N.A., Turning surface assembly units consisting of combinations of dissimilar materials, Vestn. Mosk. Gos. Tekh. Univ., Stankin, 2017, no. 3 (42), pp. 48–51.

Download references

Author information

Authors and Affiliations

  1. AO Scientific-Research Engineering Institute, 143912, Balashikha, Russia

    E. A. Kudryashov, I. M. Smirnov & N. A. Khizhnyak

Authors
  1. E. A. Kudryashov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. I. M. Smirnov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. N. A. Khizhnyak
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to E. A. Kudryashov.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Kudryashov, E.A., Smirnov, I.M. & Khizhnyak, N.A. Tools with Redesigned Cutting Inserts for Intermittent Cutting. Russ. Engin. Res. 39, 237–241 (2019). https://doi.org/10.3103/S1068798X19030146

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X19030146

Keywords:

Search

Navigation