Abstract
In thick-sheet rolling, formulas are obtained for the kinematic parameters of the deformation source, the torques, and the front flexure of the sheet leaving the rollers. A criterion for front linearity of the sheet is developed. The basic parameters affecting sheet flexure are the temperature gradient over the slab cross section and the insertion angle of the sheet in the rollers.
Similar content being viewed by others
References
Rashnikov, V.F., Senichev, G.S., Dubrovskii, B.A., et al., Seventy-Fifth Anniversary of Magnitki Rolled Products, Stal’, 2008, no. 7, pp. 9–12.
Salganik, M.V., Shmakov, A.V., and Popov, V.V., Controlled Rolling of Low-Temperature Pipe at the 5000 Mill, Stal’, 2009, no. 10, pp. 47–50.
Tselikov, A.I. and Grishkov, A.I., Teoriya prokatki (Rolling Theory), Moscow: Metallurgiya, 1970.
Vydrin, V.N., Dinamika prokatnykh stanov (Rolling-Mill Dynamics), Moscow: Metallurgiya, 1960.
Nikolaev, V.A., Skorokhodov, V.N., and Polukhin, V.P., Nesimmetrichnaya tonkolistovaya prokatka (Asymmetric Thin-Sheet Rolling), Moscow: Metallurgiya, 1993.
Dolzhenkov, F.E., Konovalov, Yu.V., and Nosov, V.G., Povyshenie kachestva tolstogo lista (Improving Thick Sheet), Moscow: Metallurgiya, 1989.
Korokhov, V.G., Poltorapavlo, Yu.V., Nosov, V.G., et al., Strip Flexure in Slab Roughing on a Thick-Sheet Mill, Proizvodstvo tolstolistovoi stali (Production of Thick Steel Sheet), Moscow: Metallurgiya, 1979, pp. 34–38.
Ornatskii, E.L., Gorelik, V.S., Mit’ev, A.P., et al., Front Flexure of Thick Sheet in Rolling, Teoriya i tekhnologiya proizvodstva tolstolistovoi stali (Theory and Technology of Thick Steel-Sheet Production), Moscow: Metallurgiya, 1986, pp. 60–64.
Nikolaev, V.A., Asymmetric Strip Rolling, Izv. Vyssh. Uchebn. Zaved., Chern. Metall., 2002, no. 3, pp. 29–31.
Chichigin, V.A. and Kotsar’, S.L., Influence of Vertical Ingot Skewing on the Rolling Torque and Its Distribution among the Rollers, Teoriya i tekhnologiya prokatki (Theory and Technology of Rolling), Sverdlovsk: Metallurgizdat, 1972, pp. 49–55.
Gorelik, V.S., Nalcha, G.I., and Rudnev, A.E., Improvement in Thick-Sheet Performance by Asymmetric Rolling, Stal’, 1991, no. 11, pp. 41–44.
Maksimov, E.A., Shatalov, R.L., and Boskhamdzhiev, N.Sh., Proizvodstvo planshetnykh polos pri prokatke (Flat-Strip Production by Rolling), Moscow: Teplotekhnik, 2008.
Author information
Authors and Affiliations
Additional information
Original Russian Text © E.A. Maksimov, R.L. Shatalov, 2012, published in “Stal’,” 2012, No. 5, pp. 33–37.
About this article
Cite this article
Maksimov, E.A., Shatalov, R.L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. Part 1. Steel Transl. 42, 442–446 (2012). https://doi.org/10.3103/S0967091212050087
Published:
Issue Date:
DOI: https://doi.org/10.3103/S0967091212050087