Melphan As Anticancer And New Insights Of Drug As Parenteral Dosage Form Against SARS-CoV-2 By Using Development And Validation

A validated HPLC method was developed for the determination of Melphan (MPA) in pharmaceutical formulation. LC 20AT pump and UV-Visible detector with lexible wavelength programme and Rheodyne injector are used in this present problem. Phenomenex Synergi C18, 250 mm × 4.6 mm, 4μm or equivalent is used for this chromatography analysis. Column used in this measurement is Phenomenex Synergi C18,250mm×4.6mm,4μm or equivalent. Speci icity (stressed condition) is con irmed by no co-elution of diluent peaks, Blank as diluent, excipients peaks, Monohydroxy MPA, Dihydroxy MPA, Isopropyl ester and dimer impurity were not interfere with MPA Peak along with each other. Obtained results are 1.2 and 270103 respectively. The method developed is simple and is better than the methods reported in the literature. With the help of different studies, therefore, we recommend pursuing an induction regimen of up to six cycles in all patients to postpone treatment with high-dose MPA. By using various studies, we recommend pursuing an induction regimen of up to six cycles in all patients to postpone treatment with high-dose MPA for SARS-CoV-2.


INTRODUCTION
The Molecular formulae for MPA (MPA)is C 13 H 18 Cl 2 N 2 O 2 . MPA is generally popular as Lphenylalanine mustard, phenylalanine mustard, L-PAM, or L-sarcolysin. It is acting as derivate for phenylalanine nitrogen mustard.
MPA is represented as 4-[bis(2-chloroethyl)amino]-Lphenylalanine. MPA is readily accessible as tablet form also it used as oral administration. MPA stops synthesis of DNA along with synthesis of RNA.
Recent advances in cancer immunotherapy have offered unprecedented opportunity to harness the power of the immune system to ight against cancer. (Mellman et al., 2011) Generally MPA utilized for treating different types of myeloma, (Facon et al., 2007) ovarian cancer, AL amyloidosis along with rarely malignant melanoma. Structure Figure 1. For the estimation of MPA many type of instrumental techniques were reported in very natural drug form, pharma along with biological samples with help of electro kinetic chromatography, liquid chromatography, spcetrophotometry, HPTLC by unique nor blended arrangements. (Kumar and Nadh, 2011) proposed MPA in tablet formulation. Authors used Acetonitrile 70v/v, water 27v/v along with 1% orthophosphoric acid 3v/v composition is utilized as eluent. 1.00ml/min is rate of low. For this determination column used as ODS C-18. 275nm is wavelength. Linearity range to MPA is 2.0µg/mL -14.0µg/mL is measured. Both LOD and LOQ for MPA is identi ied within 0.5µg/ml and 1.5µg/ml respectively. (Brightman et al., 1999) proposed MPA. Linear gradient initiated from5% and ended with 60% acetonitrile as combination of water 0.5ml of acetic acid, 0.1ml of triethylamine and 0.05% w/v ammonium acetate are applied in time range as 20 min. (Malecki et al., 1993) developed a MPA known as compound C.B.3025 is the phenylalanine derivate of nitrogen mustard. It has been synthesized in 1953. Chemically, it is p-(di-2-chloroethyl) amino-L-phenylalanine. Various authors are published their work for measurement of MPA those includes VIS-spectrophotometry, electrochemistry, GC-MS along with HPLC by UV, luorescence and volt-amperometric measurement. In this present work authors are tried to explain about very rapid, more sensitive measurement of MPA by using tablets also injections RP-HPLC by using UV detection.
Very High-dose MPA along with autologous haematopoietic cell transplantation (AHCT) (Malard and Mohty, 2020) remains actual of care to it patients by newly diagnosed multiple myeloma. The Risk factors for COVID-19 severity along with death includes increased age also presence of comorbidities in combination of diabetes, hypertension, or cardiac diseases. (Onder et al., 2020) In addition to this information by China suggested as patients with cancer have a signi icantly higher incidence of severe events after contracting SARS-CoV-2 than patients without cancer (seven [39%] of 18 patients with cancer vs 124 [8%] of 1572 patients without cancer.

Equipment
LC 20AT pump and UV-Visible detector with lexible wavelength programme and Rheodyne injector are used in this present problem. Phenomenex Synergi C 18 , 250 mm × 4.6 mm, 4µm or equivalent is used for this chromatography analysis. With the help of Loba ultrasonic bath sonicator mobile phase containing the gas was separated. The common balance for measuring the drugs is employed.

Chemicals and Solvents
From local market sample MPA is purchased. Triluoroacetic acid along with Orthophosphoric acid are AR grade, Acetonitrile and water collected as HPLC grade and used. Exactly 10.00g ammonium acetate is transferred in 100.00mL standard lask. To this 50.00mL water is added after that subjected to dissolution. Again, for this solution 10.00mL glacial acetic acid, 2.00mL of triethylamine is added. Mobile Phase A is prepared by mixing exact amount with 5.00ml buffer solution is taken and diluted in 1000ml of water. After that iltered and subjected to degasation. Mobile Phase is prepared by mixing ACN, Methanol with Buffer in the combination 80.0:20.0:0.5 v/v/v and sonicated for degassing.

Preparation of Solutions
Regular solution is prepared by taking 10.00mg MPA and taken in 100.00ml standard lask. This gives 0.1 mg/mL solution. Diluted Standard as 10ppm is prepared by taking2.00mg MPA regular in 20.00ml standard lask. This preparation gives equivalent to 0.01 mg/mL. Sample solution is prepared by reconstituting 2 vials each by 5.00mL diluent after that transferred in 50.00mL standard lask. Rinse vial at least more than two times by diluent after that transferred total contents of vial in same standard lask after that diluted to required volume up to mark by suitable diluent. Placebo is prepared by reconstituting 1 vials each by 5.00mL diluent after that transferred in 25.00mL standard lask. Rinse vial at least more than two times by diluent after that transferred total contents of vial in same standard lask.Separately injected Blank (diluent) (1 injection), Diluted Standard solution (6 injections) into chromatography and check the different parameters. Theoretical plate count MPA HCl peak from diluted standard solution is not minimum to 2000. % RSD for total 6 measurements of regular solution is should not exceed to value 5.

Method Development
Various parameters were studied and considered for this analytical method validation of related substances in the drug product MPA injection concentrate 20mg/ml. For 10ppm solution of MPA by using UV spectrophotometer the spectrum in Acetonitrile was recorded separately. The wavelength is measured as 260nm. Column used as Phenomenex Synergi C18, 250 mm × 4.6 mm, 4µm or equivalent column. Acetonitrile as 80v/v, methanol as 20v/v along with buffer as 1.00ml is consumed as eluent. From the observation of the reaction 1.00mL/min low rate is acceptable for effective separation of analyte. The circumstances for the chromatographic analysis of MPA were optimized, and they are exhibited in Table 1. These are use full for the measurement of MPA in overall samples and in its formulation and for studies of SARS-CoV-2.

Proposed Method And Requirements For Validation System Suitability
Injected blank as 1 injection, system Suitability solution as 1injection, sensitivity solution as 1 injection, diluted regular solution as 6 measurements. Results obtained were inalized as system should favorable for analytical method corroboration. Results are tabulated in Table 2.

Speci icity
Conducted speci icity criteria of method by introducing Blank (diluent), Placebo preparation, s regular solution, Monohydroxy MPA, Dihydroxy MPA, MPA isopropyl ester, MPA Dimer, Sample Preparation, Spiked sample with known impurities into the chromatographic system and recorded the retention times. The peaks of Blank (diluent), Placebo, Monohydroxy MPA, Dihydroxy MPA, MPA isopropyl ester and MPA dimer should not interfere MPA peak and each other. From the below results, it can be concluded that no retardation of other peaks of placebo & impurity peaks including MPA peak. Carried out this experiment by passing Blank injecting blank as diluent, placebo preparation, Diluted standard solution, Monohydroxy, Dihydroxy, isopropyl ester, dimer of MPA, prepared sample, spiked sample with known impurities and documented different retention times. Results are tabulated in Table 3.

Stressed Condition Studies
Stressed condition of MPA injection shall be done for inalizing stability information and also degradation path way or through its shelf life or any non-persistent substance is identi ied that may not combined by using MPA injection peak. Various solutions are prepared for this study like sample, placebo, Acid Stressed sample (1.0N HCl), Alkali Stressed sample (1.0N NaOH), 3.0% w/v Peroxides of Hydrogen Stressed (3.0%w/v H2O2), Neutral Stressed, UV light exposed, Photo stability exposed Sunlight exposed, Thermal stressed (Dry heat) sample.
For repeated analysis alkali stressed sample (1.0N NaOH) at 25 • C for 5 minutes is measured. Neutral stressed sample for 2 hours. Finally, concluded that Sample is found to be degrading in alkali condition and Neutral condition. By using sunlight it is slightly undergoing degradation in Hydrogen peroxide. No degradation is observed in Photo stability, acidic, thermal and UV light stressed condition. However, unknown impurities, related compounds along with degradation impurity are well scattered from MPA peak. MPA peak is pure, which was con irmed by Chromeleon software. Hence, this related substance procedure is considered for product release ad shelf-life.

System Precision
The Retention Time (Rt) and area for total 6 determinations are calculated along with that % RSD may also calculated. Injected diluent as blank and standard into system. Recorded the % RSD for Rt and response of peak for MPA. It is evident that from the obtained data Rt and peak responses are same which is supported by RSD. Due to this reason, inalized that precision of system reaches exactness of method validation. The results obtained are showed in the in Table 4.

Method Precision
Consistence substance of a pointed batch is subjected to analysis to 6 times as total. Therefore, the conclusion from the above procedure is precise. % RSD of impurities 0.05% and above for total 6 measurements is 15.0.%RSD of total impurities for total 6 measurements is 10.0. From below values, it is inalized as this method is precise. Results are tabulated in Table 5.

Intermediate Precision
Calculated the Percentage of impurities compared the results obtained in method of precision and Precision of Intermediate, calculated % RSD. % RSD of impurities 0.05% and above for total 6 measurements is NMT 15.0.% RSD of Total impurities for 6 measurements is NMT 10.% RSD of the related compounds 0.05% and above for 12 preparation NMT is 15.0. Impurity below LOQ is not considered in total impurity. Comparison between Method Precision and Intermediate Precision results are tabulated in Table 6.

Stability In analytical Solution
Percentage Difference in range response for peak in regular & unknown preparative should be in the range ± 5.0 from beginning area and area after speci ied period.% variations of area response for MPA peaks in diluted standard preparation is within ± 5.0 from the initial area to after period. For Impurity 0.05% above and total impurity, % variation in the area counts between started time and ended time. Difference in area response as initial also after speci ied period is within ± 15.0 and 10.0. Monohydroxy MPA and MPA Dimer impurities are above LOQ. Other known and unknown impurities are below LOQ. The Diluted solution of standard is stable to about 51 hours at temperature of 5 • C. The sample solution is stable upto 17hours in 5 • C (% difference of monohydroxy MPA along with MPA dimer is 0.3& 2.0). For total impurity sample solution is stable upto 17 hours. % difference for total impurity is -1.2.            Table 7, graphs are igured from Figures 2, 3, 4, 5 and 6.

Limit of Detection and Quantitation
To con irm LOD along with LOQ calculated theoretically from above; prepared freshly solution of MPA, Monohydroxy MPA, Dihydroxy MPA, Isopropyl ester and MPA dimer at LOD and LOQ concentration and inject into the chromatograph (LOD range single and LOQ range 6 injections). Calculated % RSD and calculated percentage of LOD and LOQ with respect to working strength. % RSD of area response obtained from 6 injections at LOQ range value is NMT10.0.
The results are tabulated in Table 8.

Robustness
Changed oven temperature to ±5 • C. From results, this method is inalized that process is robust towards small variation in process parameters. By results obtained inally it is inalized that proposed process is robust for very small changes in different parameters of method. The results are tabulated in Table 9.

Melphan as a treatment of SARS-CoV-2
Other critical services to patients that have highdose MPA along with AHCT that could be negatively concerned by SARS-Cov-2 includes connection of blood products, as number of blood donors might minimum by guidance to self-isolate, which may leads to minimum blood and platelet prod-ucts. (Ranney et al., 2020;Pagano et al., 2020) Finally, deciding whether utilizing high-dose MPA along with AHCT are the right treatments for patients by multiple myeloma could be very carefully decided in current SARS-Cov-2 pandemic situation. For patients with high-risk cytogenetics, the situation is more complex. These patients might need to have high-dose MPA and AHCT as irst-line treatments. Still, approximately 18% of patients have asymptomatic SARS-CoV-2 infection, we recommend testing patients for SARS-CoV-2 before transplant. After intravenous administration, mean plasma t 0.5 α was 8.0±2.3 min, t 0, 5 β was 63.3±8.7 min, and total systemic clearance is identi ied as 510.4 ± 57.9 ml/min (Woodhouse et al., 1983).

RESULTS AND DISCUSSION
For various validation criteria of HPLC, different elute ratios are veri ied. Satisfactory separation with good peak symmetry is measured in combination of both elute A and B. Column used in this measurement is Phenomenex Synergi C18, 250 mm × 4.6 mm, 4µm or equivalent (P.No. 673882-1). Speciicity(stressed condition) the peaks of Blank (diluent), excipeients peaks, Monohydroxy MPA, Dihydroxy MPA, Isopropyl ester and Dimer impurity were not interfere with MPA Peak along with each other. Match factor is more than 0.99 /990.0. For system criteria symmetry factor for MPA peak is 2.
Obtained results are 1.2 and 270103 respectively. Relative regular deviation (% RSD) for total 6 measurements of regular solution is maximum to value 5. % RSD of retention time for MPA peak measured from total 6 measurements of diluted regular solution is 1.0 with % RSD of the area response for MPA peak measured from total 6 measurements of diluted regular solution is 5.% RSD for sum of impurities from total 12 measurements (method precision & intermediate precision) is 10.0 which is identi ied as 1.7. % difference in area response from minimum to speci ied period from sample solution is -1.2 at 25 • C. Distinct visible peak is measured at LOD level strength. Proposed HPLC method for estimation of related substance in drug product MPA for injection is validated as per analytical method validation. Accuracy of this method is established for MPA for injection 50mg/ml. Intermediate precision, LOD along with LOQ are performed. System suitability test is established including related parameters. Taking into account, that severe cases of SARS-Cov-2 are characterized by hyperergic in lammatory counter it can be counterfeit that inhalation utilization of very low-doses of MPA due to its antiin lammatory characteristic can be adequate treatment to patients those who are facing problem with SARS-Cov-2 -associated pneumonia.

CONCLUSIONS
Proposed method is speci ic with linear in the speci ied range method is also indicating as evidenced by stressed studies. This proposed method is found to be linear in the speci ied range for MPA and its related impurities. Hence, by using this process inally it is concluded that this method stands validated it can be used for routine with stability analysis. Therefore, we recommend pursuing an induction regimen of up to six cycles in all patients to postpone treatment with high-dose MPA for treatment of SARS-CoV-2.

ACKNOWLEDGEMENT
Authors are wish to acknowledge GITAM Deemed to be university and shilpa medicare pvt.ltd., to carry out this work.