Res. Agr. Eng., 2017, 63(1):36-44 | DOI: 10.17221/82/2015-RAE

Analysis of production parameters of single-lap bonds adhesive bonded with composites based on aluminium fillerOriginal Paper

Miroslav Müller
Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Czech Republic

In the area of bonding of sheets of metals, mainly in construction of transport and agricultural machines, single-lap bonds are used. In manufacturing corporations focused on bonding of the metal sheets the technologies such as riveting, welding and adhesive bonding are particularly used. These methods are frequently combined. The aim of the research was the evaluation of lap length of alloy AlCu4Mg adhesively bonded using two component epoxy adhesive, which is commonly used in construction of machines and its modification based in addition of filler in form of aluminium microparticles. The secondary aim of the research was to ascertain the influence of microparticle volume of aluminium filler on mechanical properties of polymer particle composite. Strength of adhesively bonded joint depends on the thickness of the bonded material. Strength of the adhesively bonded joint is dependent on the lapping length of adhesively bonded material. The highest values of strength of adhesively bonded joint were reached with the coefficient of the proportional length 0.27 ± 0.01. The assumption about negative effect of filler on tensile strength during the experiments was not confirmed.

Keywords: lCu4Mg; adhesive bond strength; lapping length; sheet of metal; particle reinforced composite; scanning electron microscopy (SEM)

Published: March 31, 2017  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Müller M. Analysis of production parameters of single-lap bonds adhesive bonded with composites based on aluminium filler. Res. Agr. Eng.. 2017;63(1):36-44. doi: 10.17221/82/2015-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Bene¹ P. (2012): Tradièní náøadí v nové podobì. Mechanizace zemìdìlství, 7: 10-12.
    2. Bockenheimer C., Valeske B., Possart W. (2002): Network structure in epoxy aluminium bonds after mechanical treatment. International Journal of Adhesion & Adhesives, 22: 349-356. Go to original source...
    3. Borsellino C., Bell G.D., Ruisi V.F. (2009): Adhesive joining of aluminium AA6082: The effects of resin and surface treatment. International Journal of Adhesion and Adhesives, 29: 36-44. Go to original source...
    4. Cho J., Joshi M.S., Sun C.T. (2006): Effect of inclusion size on mechanical properties of polymeric composites with micro and nano particles. Composites Science and Technology, 66: 1941-1952. Go to original source...
    5. Ebnesajjad S., Landrock A.H. (2014): Adhesives Technology Handbook. William Andrew.
    6. Eitner U., Rendler L.C. (2014): The mechanical theory behind the peel test: mechanical tests. Energy Procedia, 55: 331-335. Go to original source...
    7. Fu S.Y., Feng X.Q., Lauke B., Mai Y.W. (2008): Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate-polymer composites. Composites: Part B: Engineering, 39: 933-961. Go to original source...
    8. Galusek D., Sedláèek J., Riedel R. (2007): Al2O3-SiC composites prepared by warm pressing and sintering of an organosilicon polymer-coated alumina powder. Journal of the European Ceramic Society, 27: 2385-2392. Go to original source...
    9. Herák D., Müller M., Dajbych O., Simanjuntak S. (2009): Bearing capacity and corrosion weight losses of the bonded metal joints in the conditions of Indonesia, North Sumatra province. Research in Agricultural Engineering, 55: 94-100. Go to original source...
    10. Hricova J. (2014): Environmentally conscious manufacturing: the effect of metalworking fluid in high speed machining. Key Engineering Materials, 581: 89-94. Go to original source...
    11. Jackel M., Scheibner W. (1991): Boundary layer induced modification of thermal and mechanical properties of epoxy resin composites. Cryogenics, 31: 269-272 Go to original source...
    12. Kahramana R., Sunar M., Yilbas B. (2008): Influence of adhesive thickness and filler content on the mechanical performance of aluminium single-lap joints bonded with aluminium powder filled epoxy adhesive. Journal of Materials Processing Technology, 205: 183-189. Go to original source...
    13. Kejval J., Müller M. (2013): Mechanical properties of multicomponent polymeric composite with particles of Al2O3/ SiC. Scientia Agriculturae Bohemica, 44: 237-242. Go to original source...
    14. Kim H., Khamis M.A. (2001): Fracture and impact behaviours of hollow micro-sphere/epoxy resin composites. Composites Part A: Applied Science and Manufacturing, 32: 1311-1317. Go to original source...
    15. Lang T.P., Mallick P.K. (1999): The effect of recessing on the stresses in adhesively bonded single-lap joints. International Journal of adhesion & Adhesive, 19: 257-271. Go to original source...
    16. Loctite (1998): Der Loctite. Worldwide Design Handbook. München, Loctite European Group.
    17. Messler R.W. (2004): Joining of materials and structures from pragmatic process to enabling technology. Burlington, Elsevier.
    18. Müller M. (2013a): Research of liquid contaminants influence on adhesive bond strength applied in agricultural machine construction. Agronomy Research, 11: 147-154.
    19. Müller M. (2013b): Research of renovation possibility of machine tools damage by adhesive bonding technology. Manufacturing Technology, 13: 504-509. Go to original source...
    20. Müller M., Herák D. (2010): Dimensioning of the bonded lap joint. Research in Agricultural Engineering, 56: 59-68. Go to original source...
    21. Müller M., Valá¹ek P. (2012): Degradation medium of agrokomplex - adhesive bonded joints interaction. Research in Agricultural Engineering, 58: 83-91. Go to original source...
    22. Müller M., Valá¹ek P. (2013a): Assessment of bonding quality for several commercially available adhesives. Agronomy Research, 11: 155-162.
    23. Müller M., Valá¹ek P. (2013b): Comparison of variables influence on adhesive bonds strength calculations. Manufacturing Technology, 13: 205-210. Go to original source...
    24. Müller M., Herák D., Valá¹ek P. (2013): Degradation limits of bonding technology depending on destinations Europe, Indonesia. Tehnicki Vjesnik - Technical Gazzete, 20: 571-575.
    25. Novák M. (2012): Surfaces with high precision of roughness after grinding. Manufacturing technology, 12: 66-70. Go to original source...
    26. Olia M., Rossettos J.N. (1996): Analysis of adhesively bonded joints with gaps subjected to bending. International Journal of Solids and Structures, 33: 2681-2693. Go to original source...
    27. Pereira J.M., Ferreira F.V., Antunes P.J., Bártolo A.M. (2010): Analysis of manufacturing parameters on the shear strength of aluminium adhesive single-lap joints. Journal of Materials Processing Technology, 210: 610-617. Go to original source...
    28. Tamai Y., Aratanic K. (1972): Experimental study of the relation between contact angle and surface roughness. The Journal of Physical Chemistry, 22: 3267-3271. Go to original source...
    29. Valá¹ek P. (2014): Mechanical properties of epoxy resins filled with waste rubber powder. Manufacturing Technology, 14: 632-637. Go to original source...
    30. Valá¹ek P. (2015): Polymeric microparticles composites with waste EPDM rubber powder. Agronomy Research, 13: 723-731.
    31. Valá¹ek P., Müller M. (2015): Properties of adhesives used for connecting in automotive industry. Manufacturing Technology, 15: 232-237. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content