Abstract
Measuring the toughness of brittle coatings has always been a difficult task. Coatings are often too thin to easily prepare a freestanding sample of a defined geometry to use standard toughness measuring techniques. Using standard indentation techniques gives results influenced by the effect of the substrate. A new technique for measuring the toughness of coatings is described here. A precracked micro-beam was produced using focused ion beam (FIB) machining, then imaged and loaded to fracture using a nanoindenter.
Similar content being viewed by others
Change history
06 March 2017
An Erratum to this paper has been published: https://doi.org/10.1557/jmr.2017.84
References
W.C. Oliver and G.M. Pharr: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments, J. Mater. Res. 7, 1564 (1992).
M. Sakai and C. Bradt: Fracture toughness testing of brittle materials, Int. Mater. Rev. 38, 53 (1993).
C.B. Ponton and R.D. Rawlings: Vickers indentation fracture toughness test. Part 1: Review of literature and formulation of standardised indentation toughness equations, Mater. Sci. Technol. 5, 865 (1989).
P.D. Warren: A simple method for determining KIc in brittle materials using Hertzian indentation, J. Eur. Ceram. Soc. 15, 385 (1995).
X. Li, D. Diao and B. Bhushan: Fracture mechanisms of thin amorphous carbon films in nanoindentation, Acta Mater. 45, 4453 (1997).
J. Ding, Y. Meng and S. Wen: Mechanical properties and fracture toughness of multilayer hard coatings using nanoindentation, Thin Solid Films 371, 178 (2000).
R.-S. Kim and J.A. Nairn: Fracture mechanics of coating/substrate systems. Part I: Analysis of tensile and bending experiments, Eng. Fract. Mech. 65, 573 (2000).
S. Johansson, A.-J. Schweitz, L. Tenerz and J. Tiren: Fracture testing of silicon microelements in situ in a scanning electron microscope, J. Appl. Phys. 63, 4799 (1988).
S. Sundarajan, B. Bushan, T. Namazu and Y. Isono: Mechanical property measurements of nanoscale structures using an atomic force microscope, Ultramicroscopy 91, 111 (2002).
T. Namazu, Y. Isono and T. Tanaka: Evaluation of size effect on mechanical properties of single crystal silicon by nanoscale bending test using AFM, J. Microelectromech. Syst. 9, 450 (2000).
K. Komai, K. Minoshima and S. Inoue: Fracture fatigue behavior of single crystal silicon microelements and nanoscopic AFM damage evaluation, Microsyst. Technol. 5, 30 (1998).
D. Son, H.-J. Jeong and D. Kwon: Film-thickness considerations in microcantilever-beam test in measuring mechanical properties of metal thin films, Thin Solid Films 437, 182 (2003).
J. McCarthy, Z. Pei, M. Becker and D. Atteridge: FIB micromachined submicron thickness cantilevers for the study of thin film properties, Thin Solid Films 358, 146 (2000).
K. Minoshima, T. Terada and K. Komai: Influence of nanometre-sized notch and water on the fracture behaviour of single crystal silicon microelements, Fatigue Fract. Eng. Mater. Struct. 23, 1033 (2000).
R. Haswell, D.W. McComb and W. Smith: Preparation of site-specific cross-sections of heterogeneous catalysts prepared by focused-ion-beam milling, J. Microsc. 211, 161 (2003).
K.E. Petersen: Silicon as a mechanical material: Proc. IEEE. 70, 420 (1982).
C. John St.: The brittle-to-ductile transition in pre-cleaved silicon, Philos. Mag. 32, 1194 (1975).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Di Maio, D., Roberts, S.G. Measuring fracture toughness of coatings using focused-ion-beam-machined microbeams. Journal of Materials Research 20, 299–302 (2005). https://doi.org/10.1557/JMR.2005.0048
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/JMR.2005.0048