Abstract
The four-point bend (4PB) test is an industry standard in assessment of adhesion in thin films. Obtauning crack propagation along the desired interface plays a cardinal role in the success of this test. Crack penetration and deflection at a bimaterial interface has been extensively studied in the past. Most generalresults are based on asymptotic analyses involving the interface between two semi-infinite media. Theresults of these analyses cannot be directly used in case of the 4PB test since the boundary conditions and finite size effects in actual test specimen geometry are not accounted for. The purpose of this paper is twofold: first to develop a simple methodology to understand the preferred faulure mode in a 4PB test and gaun insight into the factors governing its success; second to examine the extent to which theresults can bereconciled with those reported previously based on analysis of a crack in two semi-infinite media bonded together at the interface.
Similar content being viewed by others
References
ASTM D3359-97, Standard Test Methods for Measuring Adhesion by Tape Test (American Society for Testing and Materials, West Conshohocken, PA, 1998).
D.B. Marshall and A.G. Evans: Measurement of adherence of residually stressed thin films by indentation. I. Mechanics of interface delamination. J. Appl. Phys. 56, 2632 (1984).
C. Rossington, A.G. Evans, D.B. Marshall, and B.T. Khuriyakub: Measurement of adherence of residually stressed thin films by indentation. II. Experiments with ZnO/Si. J. Appl. Phys. 56, 2639 (1984).
M.R. Begley, D.R. Mumm, A.G. Evans, and J.W. Hutchinson: Analysis of a wedge impression test for measuring the interface toughness between films/coatings and ductile substrate. Acta Mater. 48, 3211 (2000).
A.A. Volinsky, J.B. Vella, and W.W. Gerberich: Fracture toughness, adhesion and mechanical properties of low-K dielectric thin films measured by nanoindentation. Thin Solid Films 429, 201 (2003).
A.A. Volinsky and W.W. Gerberich: Nanoindentation techniques for assessing mechanical reliability at the nanoscale. Microelectron. Eng. 69, 519 (2003).
T.W. Wu: Microscratch and load relaxation tests for ultrathin films. J. Mater. Res. 6, 407 (1991).
J. Kim, K.S. Kim, and Y.H. Kim: Mechanical effects of peel adhesion test. J. Adhes. Sci. Technol. 3, 175 (1989).
Y.S. Kim and N. Aravas: Elastoplastic analysis of the peel test. Int. J. Solids Structure 24, 417 (1998).
H.M. Jensen and M.D. Thouless: Effect of residual stresses in the blister test. Int. J. Solids Struct. 30, 779 (1993).
R.J. Hohlfelder, J.J. Vlassak, W.D. Nix, H. Luo, and C.E.D. Chidsey: blister test analysis methods, in Thin Films: Stresses and Mechanical Properties V, edited by S.P. Baker, C.A. Ross, P.H. Townsend, C.A. Volkert, and P. Børgensen. (Mater. Res. Soc. Symp. Proc. 356, Pittsburgh, PA, 1995), pp. 585–590.
R.J. Hohlfelder, J.J. Vlassak, W.D. Nix, H. Luo, and C.E.D. Chidsey: Measuring interfacial toughness with the blister test, in Thin Films: Stresses and Mechanical Properties VI, edited by W.W. Gerberich, H. Gao, J-E. Sundgren, and S.P. Baker (Mater. Res. Soc. Symp. Proc. 436, 1996), pp. 115–120.
J.C. Hay, E.G. Liniger, and Xiao Hu Liu: Evaluation of the modified edge lift-off test for adhesion characterization in microelectronic multifilm applications. J. Mater. Res. 16, 385 (2001).
R.H. Dauskardt, M. Lane, Q. Ma, and N. Krishna: Adhesion and debonding of multi-layer thin film structures. Engr. Fract. Mech. 61, 141 (1998).
A.A. Volinsky, N.R. Moody, and W.W. Gerberich: Interfacial toughness measurement for thin films on substrate. Acta Mater. 50, 441 (2003).
A. Bagchi and A.G. Evans: The mechanics and physics of thin film decohesion and its measurement. Interface Sci. 3, 169 (1996).
T. Scherban, B. Sun, J. Blaune, C. Block, B. Jin, and E. Andideh: Interfacial adhesion of copper-low k interconnects (IEEE Interconnect Conference, San Francisco, CA, 2001).
S. Roham, K. Hardikar, and P. Woytowitz: Stress analysis of 4-point bend test for thin film adhesion, in Mechanical Properties Derived from Nanostructuring Materials, edited by D.F. Bahr, H. Kung, N.R. Moody, and K.J. Wahl (Mater. Res. Soc. Symp. Proc. 778, Warrendale, PA, 2003), pp. 73–78.
J.R. Rice: A path independent integral and the approximate analysis of straun concentration by notches and cracks. J. App. Mech. 35, 379 (1968).
P.G. Charalambides, J. Lund, A.G. Evans, and R.M. McMeeking: A test specimen for determining the fracture resistance of bimaterial interfaces. J. Appl. Mech. 56, 77 (1989).
J.W. Hutchinson and M.Y. He: Crack deflection at an interface between dissimilar elastic materials. Int. J. Solids Struct. 25, 1053 (1989).
J.W. Hutchinson, M.Y. He, and A.G. Evans: Crack deflection at an interface between dissimilar elastic materials: Role of residual stress. Int. J. Solids Struct. 31, 3443 (1994).
J. Dundurs: Edge-bonded dissimilar orthogonal elastic wedges. J. Appl. Mech. 36, 650 (1969).
G.R. Irwin: Fracture Dynamics, in Fracturing of Metals, edited by F. Jonassen et al. (Am. Soc. Metals, Cleveland, OH, 1948), pp. 147–166.
ABAQUS Structural solver: (Hibbit, Karlsson & Sorensen, Inc., Pawtucket, RI, 2003).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Roham, S., Hardikar, K. & Woytowitz, P. Crack penetration and deflection at a bimaterial interface in a four-point bend test. Journal of Materials Research 19, 3019–3027 (2004). https://doi.org/10.1557/JMR.2004.0376
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/JMR.2004.0376