Performance of real-time adaptive optics compensation in a turbulent channel with high-dimensional spatial-mode encoding

The orbital angular momentum (OAM) of photons is a promising degree of freedom for high-dimensional quantum key distribution (QKD). However, effectively mitigating the adverse effects of atmospheric turbulence is a persistent challenge in OAM QKD systems operating over free-space communication channels. In contrast to previous works focusing on correcting static simulated turbulence, we investigate the performance of OAM QKD in real atmospheric turbulence with real-time adaptive optics (AO) correction. We show that, even our AO system provides a limited correction, it is possible to mitigate the errors induced by weak turbulence and establish a secure channel. The crosstalk induced by turbulence and the performance of AO systems is investigated in two configurations: a lab-scale link with controllable turbulence, and a 340 m long cross-campus link with dynamic atmospheric turbulence. Our experimental results suggest that an advanced AO system with fine beam tracking, reliable beam stabilization, precise wavefront sensing, and accurate wavefront correction is necessary to adequately correct turbulence-induced error. We also propose and demonstrate different solutions to improve the performance of OAM QKD with turbulence, which could enable the possibility of OAM encoding in strong turbulence.

where L is the maximal OAM quantum number in use. A high-fidelity sorter for efficiently measuring these MUBs has been developed, and its effectiveness has been demonstrated in QKD systems as well [19,39,40]. However, its counterparts for mode spacing larger than one have not yet been demonstrated, and an inefficicent measurement device may introduce additional security loopholes [41]. Therefore, an efficient approach which can both take the full advantages of high-dimensional encoding and reduce the crosstalk from atmospheric turbulence is still under investigation. Conceptually, the simplest technique for overcoming turbulence-induced errors is to use adaptive optics (AO) to correct the phase errors and recover the benefits of using the highdimensional encoding QKD system. However, since OAM states are very sensitive to wavefront errors, any imperfect correction may actually lead to an increase rather than a decrease in QSER, and hence the failure of QKD system. Most relevant experimental works only focus on correcting static turbulence simulated by single or multiple random phase screens, which is a significantly simplified model ignoring the dynamic nature of atmospheric turbulence [30][31][32]34]. In addition, some theoretical simulations predict that a simple AO system may not be adequate for turbulence correction [42][43][44]. Therefore, under real dynamic turbulence, using AO systems to correct errors in OAM states remains very challenging, and the performance of AO correction in real atmospheric turbulence is still unknown and needs to be investigated.
To thoroughly study the effect of AO correction on OAM states, we investigate the performance of an OAM QKD system with real-time AO compensation in both a lab-scale and a cross-campus link. We first quantitatively investigate the performance of such a QKD system in the lab with a controllable source of turbulence. We find out that, even though AO only provides a limited correction, the quantum channel disturbed by weak turbulence can remain secure when the compensation is enabled. We then study the performance of OAM QKD in a 340 m long cross-campus link. Due to the relatively high turbulence level and modest performance of AO, we can reduce the QSER in the cross-campus link but it is still too high to guarantee the security of the channel. Based on our observation and previous simulation results, advanced AO system with fine beam tracking, reliable beam stabilization, precise wavefront sensing and accurate wavefront correction is necessary to correct the error induced by moderate or strong turbulence. In our summary, we propose three different solutions to improve the performance, and show that the performance of spatial mode QKD system can be improved if these methods are implemented. Both signal and beacon beams go through the center of the RH. The size of the signal beam is selected to cover the central part of the DM (3×3 actuators) to avoid the cutoff from the edges. The size of the beacon beam overfills the DM aperture to provide a precise estimation of turbulence across the DM. The polarization of the signal beam is controlled by a polarizer to encode information while the polarization of the beacon beam is fixed in |H state.

Lab-scale link under controllable turbulence
We first investigate the influence of atmospheric turbulence on OAM states and the conjugate ANG states under different levels of turbulence, and then perform real-time AO compensation on these states. The experimental setup is shown in Fig. 1. Alice prepares her states using a spatial light modulator (SLM) and a 633 nm He-Ne laser. The laser is first coupled into a single mode fiber (SMF) to generate a fundamental Gaussian state ( = 0), which is then collimated with an objective and illuminates SLM1 (SDE1024 from Cambridge Correlators Ltd). A pair of lenses ( f 1 = 0.75 m and f 2 = 0.5 m) together with an iris are used to select the desired state of light, carried by the first-order diffraction from the SLM. A polarizer and a half-wave plate (HWP1) after these lenses are used to prepare four different polarization states: horizontal (|H ), vertical (|V ), diagonal (|D ) and anti-diagonal (| A ). The beacon beam, which comes from a 532 nm green laser, is collimated using an aspheric lens from a SMF. The signal beam (the beam encoded by SLM1) is combined with the beacon beam through the use of a beam splitter (BS). Afterwards, both beams propagate collinearly through the turbulent channel consisting of a turbulence cell (TC) and three mirrors. The TC is a ring heater (RH) blown on by a fan. We adjust the level of turbulence by changing three parameters: the temperature of RH, the fan speed and the number of times that the beams go through the TC. The separation between BS and RH is 1.5 m while the separations between RH and the first two mirrors (M4 and M5) are both 0.15 m. For the strongest turbulence, the beams go through the TC four times and are then reflected to the deformable mirror (DM) by a fast steering mirror (FSM, OIM5002 from Optics In Motion LLC). For the weakest turbulence, RH is moved 0.3 m away from the beams so that the beams simply bypass the RH but still experience some turbulence from the edge of RH. The AO compensation system consists of two parts. The first part has a FSM and a quad-cell position detector (PD), and is used to correct the beam wander induced by the 2nd and 3rd Zernike polynomials (in Noll index, i.e. tip and tilt). To redirect part of the green beacon beam to PD, a 488 nm 50/50 non-polarizing BS (#48-217 from Edmund Optics) is used as a dichroic mirror, which leads to 7.40% loss in the signal beam. Since one set of FSM and PD is involved, only two degrees of freedom can be corrected (either x-y position or the propagation direction on the DM, i.e. the x-y momentum). In our configuration, the beam position on the DM is corrected but not the propagation direction. To minimize the tip-tilt error on DM induced by the FSM, the separation between FSM and PD is much larger than the separation between FSM and TC. That is to say, the FSM is in the near-field of turbulence while the PD is in the far field. The second part of the AO system consists of a Shack-Hartmann wavefront sensor (WFS, WFS20-7AR from Thorlabs) and a DM with 32 actuators (DM32-35-UM01 from Boston Micromachine). WFS is working in the high-speed mode with 23×23 microlens in use, and the measured Zernike coefficients are limited to the first 15 terms to give the best performance. The selection of this optimal specification will be discussed later. The compensation control is performed by Thorlabs AO kit software (Version 4.40). To get the optimal wavefront measurement, the beams at DM plane are imaged onto WFS plane using two Thorlabs best-form spherical singlet lenses ( f 3 = 0.20 m and f 4 = 0.15 m). Before the WFS, a 605 nm dichroic mirror (#34-740 from Edmund Optics) is used to reflect the green beacon beam but transmit the red signal beam. To reduce the noise from beacon beam [45], a laser line filter (#68-943 from Edmund Optics) at 633 nm is used to filter out the residual green light. The DM plane is then imaged onto SLM2 using another imaging system, consisting of two Thorlabs best form spherical singlet lenses ( f 5 = 0.2 m and f 6 = 0.2 m), to perform projective measurements [35]. To measure the polarization degree of freedom, a polarizer and a half-wave plate (HWP2) are used after the laser line filter. HWP2 is used to rotate the polarization state (|H , |V , |D or | A , which can be used as another degree of freedom in hybrid encoding and will be discussed later) to |H since liquid crystal SLM only affects horizontally polarized light.
To quantify the level of turbulence, we first introduce the Fried parameter r 0 which is the spatial coherence length of atmospheric eddies (called turbules), and then use the quantity D/r 0 to describe the level of turbulence, where D is the beam diameter because the beacon Gaussian beam underfills the collection aperture [46,47]. Therefore, the quantity D/r 0 denotes the number of turbules inside the beam cross section. A large D/r 0 indicates strong turbulence (D/r 0 > 1) while a small D/r 0 stands for weak turbulence (D/r 0 < 1) [48]. In our experimental setup, the OAM states with quantum number from −2 to 2 comprise our encoding space with dimension d = 5. The r 0 under different levels of turbulence are estimated from the beam wander at the receiver side, which leads to an experimental D/r 0 from 0.11 to 3.06. This range spans turbulence levels from weak turbulence to strong turbulence.
We measure the crosstalk matrices between the prepared and received states under different turbulence situations, and calculate the measured fidelity (F) as a function of turbulence strength D/r 0 , which are shown in Fig. 2. With the turbulence turned off, we measure an average fidelity F = 93.69% of the MUBs (the blue dot in Fig. 2(c)). The fidelity of the OAM basis and ANG basis can be found in Fig. 2(a) and (b) respectively. Each measurement takes 1.5 mins so that the total measurement time for the average fidelity of the MUBs under one specific level of turbulence is about 150 mins. The measured fidelity of the MUBs is above the fidelity threshold F = 79.01% for this d = 5 system, which indicates that a secure quantum channel can be established [15,16]. As D/r 0 increases, F drops quickly due to an increase in fluctuation levels, and the fidelity in the OAM basis matches well with the theoretical prediction F = 1 − [1 + c(D/r 0 ) 2 ] −1/2 , where coefficient c is 3.404 for the no turbulence case [28]. The yellow and red curves are least square fitting results of the experimental data. Even under weak turbulence with D/r 0 = 0.11, the average fidelity in the ANG basis (78.04%) is below the threshold. After we turn on the AO, the fidelity is improved to 80.07% in the ANG basis and the fidelity in the OAM basis is improved from 86.69% to 90.35%. Therefore, a secure channel, which could not have been otherwise established, becomes possible after the AO correction is applied. The modest improvement in fidelity mainly comes from the limited performance of the AO with an insufficient number of micromirrors on DM and the trade-off between speed and accuracy of the WFS. Our DM only has 32 actuators (6×6 without corners). To avoid being cutoff by the edge, the signal beams are aligned to fall within only the central actuators (3×3 actuators for | = 1 ) while the beacon beam fills the entire aperture. The inadequate number of actuators can result in a low complexity of the wavefront that can be corrected and a poor accuracy, which means that only the first few orders of Zernike terms can be corrected with limited precision.
The trade-off between correction speed and accuracy exists in most AO systems. To provide a fast wavefront measurement, our WFS is set to operate in the high-speed mode. This specific mode can provide a measurement speed up to kHz levels by sacrificing the number of lenslets used to estimate the Zernike coefficients, which indicates that a more accurate wavefront measurement leads to a slower speed of AO compensation. To optimize the performance, one needs to first measure the bandwidth of turbulence to select an AO speed that is fast enough to sample the turbulence. This goal can be achieved by measuring the fidelity fluctuations as a function of time. Usually the atmospheric turbulence fluctuates at tens of hertz, and an AO system should have a correction bandwidth at least equal to the Greenwood frequency, which is around 60 Hz [49,50]. One also needs to consider the complexity of the Zernike terms that can be corrected by the DM. If the DM has a small number of actuators, one can limit the order of Zernikes measured by the WFS to further improve the speed. Otherwise, the number of Zernike terms measured by WFS should be large enough to avoid the waste of DM correction power. From the number of actuators on the DM, the speed of WFS, and the corresponding number of lenslets, one can determine the beam sizes on the WFS and then use a telescope to relay the field at DM to WFS. Through this procedure, the optimal combination of AO speed and the number of spots on WFS can be found, which will provide the best performance for each specific system. In our case, since the complexity of the DM (6×6 actuators) limits the performance of our AO system, the number of pixels of the WFS is set to a lower level (23×23 lenslets) to provide a faster sampling rate.
Another observation is that for a given AO system, the effect of AO compensation varies with the level of turbulence. For our system, the optimal performance occurs when the turbulence is moderate (D/r 0 = 0.884). As shown in Fig. 2(d), when the correction is enabled, the average fidelity of the OAM state | = 1 is improved from 64.68% to 72.24%, and the standard deviation is reduced from 11.24% to 8.68% as shown in Fig. 2(d). The probability of events which have an instantaneous fidelity larger than the threshold is increased by a factor of 3.48. In contrast, the improvement in either weak turbulence or strong turbulence is small. This is caused by different reasons in weak turbulence case and strong turbulence case.
When the turbulence is weak, the Zernike terms that introduce the majority of the error are tip and tilt, and the high-order terms are usually small and may be negligible compared to the WFS noise. Even though tip and tilt can in principle be easily corrected by two sets of FSM and PD, only one set is involved in our system. Therefore, the propagation direction of the beams leaving the FSM is not under control. After being imaged onto the DM plane, the error in the propagation direction should be corrected by the DM. Apart from tip and tilt, other aberrations in the weak turbulence are not so strong that thus not much error needs to be corrected. This combination of errors seems easy to be corrected. However, due to the inadequate number of actuators on the DM and the noise of the WFS, the AO may introduce some errors to the system that limits the potential fidelity improvement.
When strong or deep turbulence (extremely strong turbulence) is present, the high-order Zernike terms contribute more to the errors compared to low-order terms. Not only does the transverse phase profile get disturbed, but also the intensity profile is highly distorted. For example, when strong astigmatism (the 5th and 6th Zernike polynominals in Noll index) is present, the phase singularity at the center of OAM states | will get fractured into new singularities, and the OAM states will get stretched to elliptical shapes. This phenomenon is observed when D/r 0 equals to 1.90 and 3.06, which indicates that the turbulence is strong. In such a case, one simple AO system cannot sufficiently correct the errors in both phase and intensity profiles. Moreover, considering the inadequate number of actuators on the DM, the complexity of the wavefront that the DM can provide is not good enough to correct high-order terms. Therefore, an advanced AO system including multiple conjugate DMs and WFS with fast speed and high resolution is essential to correct strong and deep turbulence, while the exact specifications depends on the level of turbulence [44]. In contrast, for moderate turbulence, Zernike coefficients are usually large enough so that the WFS can provide a precise measurement, and the DM can also provide a relatively accurate correction. In the meantime, the wavefront complexity is not too great. Considering both effects, our AO correction has adequate performance in the moderate turbulence regime.

Free-space link across the UR campus
We next investigate the performance of AO compensation in a 340 m long free-space link across the University of Rochester (UR). The experimental setup is shown in Fig. 3. The state preparation stage is the same as the setup shown in Fig. 1. After BS, the combined beam is expanded using an achromatic 3× beam expander (GBE03-A from Thorlabs) and launched to the roof of Bausch & Lomb Hall through the use of one pair of mirrors (M4 and M5). As shown in the photograph, the hollow retroreflector (#49-672 from Edmund Optics) and the rotation stage are mounted on an optical breadboard, which is then mounted on the steel and aluminum frames on the roof. To protect the retroreflector, a double protection scheme is used. A high efficiency AR coated protection window is used to seal the front aperture of the retroreflector, which can prevent the formation of dew on the mirrors. The entire system, which is about 35 m above the ground, is also covered by an acrylic protection box (the front side of this box is replaced with a high efficiency window (#43-975 from Edmund Optics)) to protect the retroreflector and stage from weather. The reflected beams are collected by a pair of mirrors (3 inch clear aperture, M6 and M7), giving a Fresnel number product N f of the system equal to 4.89. An achromatic lens with 3 inch diameter (L3, f 3 = 200 mm) and a negative achromatic lens (L4, f 4 = −40 mm) are used to reduce the beam size. After this, the beams are sent to the AO system, which is almost the same as what is shown in Fig. 1 except that the DM has 140 actuators (12×12 without corners, DM140A-35-UM01 from Boston Micromachine). The large DM has more actuators which can provide a better accuracy and complexity in the wavefront correction. To match the size of the clear aperture of DM and WFS, the beam size is reduced by several imaging systems which are not shown in the figure. All the lenses used in the imaging systems are best form spherical singlet lenses to reduce the spherical aberration. The turbulence structure number C 2 n of our cross-campus link is estimated by calculating the beam wander of the returned | beam, which yields a C 2 n from 5.4×10 −15 m −2/3 to 3.2×10 −14 m −2/3 . This indicates a moderate to strong turbulence [48]. The intensity profiles of the prepared and received states under a turbulence strength C 2 n = 1.9 × 10 −14 m −2/3 are shown in Fig. 4(a), and the corresponding D/r 0 is 2.17. The intensity profiles are strongly distorted by turbulence so that the original donut shapes of the OAM states are not maintained. One can also see the effects induced by different Zernike terms from these images. For example, the first column of the received states have relatively good intensity profiles but are not at the center of receiver's aperture. These shifts are the result of tip and tilt. The received states in the 4th column show the effects induced by astigmatism. The received states are elongated into elliptical shapes, and the phase singularities are fractured into multiple vortices. In scenarios where multiple Zernike terms dominate the effect, the received states can be highly distorted leading to indistinguishable intensity profiles. For instance, as shown in the 5th column, the | = 0 and | = 1 states are split into 2 separate spots so that the two intensity profiles are similar to each other. The crosstalk matrix and the measured transmission efficiency are shown in Fig. 4(b) and (c). With AO compensation, the fidelity in the OAM basis is only improved from 19.74% to 22.57% which is far below the fidelity threshold (76.30% for d = 7 systems), and the improvement in fidelity provided by AO is modest compared to the lab-scale data with a similar turbulence level (for D/r 0 = 1.90, the lab-scale fidelity can be improved from 35.53% to 43.47%). Meanwhile, the transmission efficiency of OAM states, especially the high order terms, also fluctuates significantly. As shown in Fig. 3(c), the theoretical efficiency of the | = 3 state, including the effect of mode-dependent diffraction, should be 86.83%. However, the measured efficiency in the cross-campus link under AO correction is only 73.95% with 7.32% standard deviation, which is 12.88% lower than the expected efficiency. As a comparison, the measured efficiency of a Gaussian state is 89.21% with little fluctuation, which is only 1.58% lower than the theoretical efficiency predicted by the simulation. Considering that we are not in the strong or deep turbulence regimes, the low link efficiency with considerable fluctuations and modest improvements with AO are mainly caused by the distorted beacon beam, finite collection aperture size and mode-dependent diffraction [35,51]. These effects are only observed in the cross-campus link since the lab-scale link has a sufficiently large Fresnel number product (in our case the N f > 270 in the lab-scale link) and a more stable turbulence strength. The breakdown of the Gaussian state is usually observed in strong and deep turbulence regime but is also occasionally observed in our cross-campus link (the last photograph of the received | = 0 state in Fig. 4(a)), which leads to the failure of precise beam tracking for low Fresnel number product channels. This will then lead to a low link efficiency and a problematic tip-tilt correction, which may introduce additional errors. This effect becomes more severe for a limited Fresnel number product of the link due to finite collection aperture and long propagation distance. In this case, a high-order OAM state arriving at the receiver's aperture will be have a much larger size than the beacon beam due to mode-dependent diffraction. In our case, due to the spherical aberration and defocus, the size of the | = 3 states can vary from 6 cm to more than 7.62 cm, which exceeds the size of collection aperture (effective size is less than 7.62 cm). This indicates that, for a given Fried parameter r 0 , higher order OAM states with larger cross sections are more distorted than the lower order states. Therefore, a slight mistracking caused by a distorted beacon beam will lead to the cutoff of high-order OAM state and hence a lower efficiency and a much larger error. Meanwhile, due to the mode-dependent diffraction, the size of beacon beam (usually in | = 0 state) cannot match the size of high-order states across the whole link. This indicates that the beacon beam cannot capture all the aberrations that the high-order states experience in the link, which leads to an inefficient and inaccurate AO correction. To solve this, one may need to introduce new protocols to mitigate mode-dependent diffraction, for example as discussed in Ref. [35].
Hence, for free-space OAM QKD channels, a fine beam tracking with a reliable beam stabilization is necessary, which usually requires multiple FSMs and PDs. However, precise beam tracking is still not sufficient to correct the turbulence-induced errors since, in principle, it can only correct lowest Zernike terms (tip and tilt). As we show in the lab-scale link, high-order Zernike terms, which can only be corrected by multiple DMs and WFSs, become dominant under moderate or strong turbulence. That is to say, an advanced AO system should include two basic compositions: at least one set of beam stabilization and tracking system, and one set of advanced wavefront correction system consisting of multiple conjugate DMs and WFSs [42][43][44].

Discussion
To enhance the quality of OAM QKD, one has to mitigate the defects induced by the turbulence and improve the fidelity of the states. One possible solution is increasing the mode spacing in the encoding space. As shown in Figs. 5(a) to (d), under turbulence with D/r 0 = 1.90 and no AO correction, we can improve the average fidelity from 35.53% to 45.72% by simply encoding information with | = −4, −2, 0, 2, 4 states, which corresponds to a mode spacing of 2. If AO correction is introduced, the average fidelity can be improved from 43.47 to 57.54%. This improvement can be further enhanced if the mode spacing increases. Under the same turbulence, when the mode spacing becomes 4 (i.e. using | = −4 , | = 0 and | = 4 states), the fidelity can be improved from 71.49% to 84.33% in a d = 3 system, which is above the fidelity threshold (F = 84.05%) and a secure channel is achievable (not shown in the figure). However, this solution has two limitations. For a fixed dimension d, a large mode spacing involves states with larger | |, which will exacerbate the defects induced by mode-dependent diffraction [35] and suffer more turbulence due to the larger beam size. This will result in a lower data rate compared to an encoding system with the same dimensionality but consecutive states. The other limitation is the lack of an efficient sorter to measure the corresponding MUBs. Even though a generic quantum sorter for an arbitrary system has been proposed, implementing such an idea usually requires multiple phase screens, which results in a low overall efficiency and hence a lower key rate and more security loopholes [52,53]. Therefore, this solution might be not suitable for OAM encoding unless an efficient sorter for OAM MUBs is developed.
Another approach is to introduce a new degree of freedom, which is robust to turbulence, as the ancillary basis. By doing so, the dimension d can be increased significantly, leading to a more robust encoding system. The most straightforward idea is using polarization as the ancillary basis. The possibility of encoding information on multiple degrees of freedom has been demonstrated in Ref. [54], in which the authors cascade the spatial mode sorter after HWPs and polarizing beam splitters (PBSs) to efficiently measure the received photons. Under turbulence with D/r 0 = 1.90, the average fidelity over polarization states is 98.23%. After AO compensation, the average fidelity becomes 98.17%. This indicates that the polarization degree of freedom is robust to turbulence, and will not introduce much additional error to the combined OAM-polarization MUBs. Considering that the error threshold for a d = 5 system is 79.01%, the new joint encoding system has a threshold of 73.78% for d = 10, which is 5.23% lower than before. This improvement will allow two parties to establish a secure channel in our lab-scale link under a turbulence up to D/r 0 = 0.30, which would have been impossible without introducing the ancillary basis. The downside of this solution is that the improvement will become relatively small when the original d is large since the error threshold is a logarithmic function of d.
The last solution is to improve the performance of the entire AO correction system, which is conceptually most straightforward but also most complicated in engineering implementation. As we showed above, a simple AO system consisting of one DM, one WFS, one FSM and one PD will not be sufficient, and the performance of each device should also be improved. Note that the specifications of each device depend on the specifics of the free-space link, and the exact numbers can only be determined when the link parameters are fixed. The DM needs a large number of actuators to provide a high complexity of reconstructed wavefront, which should match the number of lenslets on the WFS and be at least complex enough to correct the dominant Zernike terms. The WFS should have an adequate number of lenslets and a high SNR for an accurate measurement. A fast enough speed, at least faster than the Greenwood frequency (around 60 Hz), to sample the time-varying wavefront and control the compensation loop is also required. The bandwidth of the FSM and PD is usually large enough and the more challenging requirement is the resolution and sensitivity. The FSM should be able to provide a sufficiently small step size but a considerable angular range so that it can accurately direct the beams toward the center of receiver's aperture even when the displacement is large. In a real free-space link, an advanced AO system with multiple devices is necessary to compensate the wavefront error introduced by atmospheric turbulence. The first section of the system should consist of two FSMs, located at the Alice's side, to point the beams at the center of collection aperture. At the Bob's side, the second section of correction system needs two FSMs and two PDs to accurately stabilize the received beams. These two sections jointly provide a precise beam tracking and control, which is essential to the advanced wavefront corrections afterwards [42][43][44]. An advanced wavefront correction system consisting of multiple conjugate DMs and WFSs with high resolution and large bandwidths is required to mitigate the error in intensity and phase profiles induced by moderate or stronger turbulence. Based on our experimental data and simulation results [42,43], we believe that an advanced AO correction system as described above is necessary, and in theory it should be able to correct the errors even under strong turbulence. However, the performance of such a system on OAM QKD still needs to be experimentally investigated.
Considering the complexity and cost of an advanced AO system as the one described above, it might be difficult to comprehensively build such a system. Therefore, we would suggest the following priority order under a limited budget. Based on our experimental observation, precise beam tracking is usually the first priority of the entire AO system. This conclusion comes from the fact that the OAM states are very sensitive to lateral displacement at the receiver's aperture, and such a tracking system is essential to the rest of the AO system. In addition, a pair of low-noise and high-bandwidth DM and WFS would work better than a pair of high-resolution but noisy low-bandwidth devices. This conclusion comes from the laboratory observation that in weak turbulence cases a pair of low-noise and high-bandwidth DM and WFS can provide better measurement and correction accuracy. However, for strong atmospheric turbulence, both of the pairs will not work and one has to use high-resolution and bandwidth DM and WFS.

Conclusion
In summary, we study the performance and the possibility of OAM QKD in a turbulent channel under real-time AO correction. The effect of turbulence and the performance of the AO system are quantitatively studied in a lab-scale link under a controllable level of turbulence. We find that, under weak turbulence, real-time AO correction can mitigate the error induced by turbulence and recover the security of the channel. For moderate and strong turbulence, a simple AO system will not be adequate to mitigate the error and an advanced AO system as we described above is required. The performance of an AO system and OAM QKD in a 340 m long free-space link with finite collection aperture is also studied. In additional to the effects we observed in the laboratory measurements, additional errors are induced by the finite collection aperture and mode-dependent diffraction. These errors require one to improve the performance of AO system so that a precise beam tracking and control can be achieved. Finally, we propose three different solutions to improve the performance of OAM QKD over a free-space communication link. We experimentally validate the effectiveness of the first two of the proposed solutions in discussion session, and discuss the possible layout of an advanced AO system.