Switchable dual-wavelength Q-switched and mode-locked fiber lasers using a large-angle tilted fiber grating

We proposed and demonstrated pulsed fiber lasers Q-switched and mode-locked by using a large-angle tilted fiber grating, for the first time to our best knowledge. Owing to the unique polarization properties of the large-angle tilted fiber grating (LA-TFG), i.e. polarization-dependent loss and polarization-mode splitting, switchable dual-wavelength Q-switched and mode-locked pulses have been achieved with short and long cavities, respectively. For the mode-locking case, the laser was under the operation of nanosecond rectangular pulses, due to the peak-power clamping effect. With the increasing pump power, the durations of both singleand dualwavelength rectangular pulses increase. It was also found that each filtered wavelength of the dual-wavelength rectangular pulse corresponds to an individual nanosecond rectangular pulse by employing a tunable bandpass filter. ©2015 Optical Society of America OCIS codes: (060.3735) Fiber Bragg gratings; (140.3510) Lasers, fiber; (140.3540) Lasers, Qswitched; (140.4050) Mode locked lasers. References and links 1. B. C. Stuart, M. D. Feit, A. M. Rubenchik, B. W. Shore, and M. D. Perry, “Laser-induced damage in dielectrics with nanosecond to subpicosecond pulses,” Phys. Rev. Lett. 74(12), 2248–2251 (1995). 2. A. J. McGrath, J. Munch, G. Smith, and P. Veitch, “Injection-seeded, single-frequency, Q-switched erbium:glass laser for remote sensing,” Appl. Opt. 37(24), 5706–5709 (1998). 3. X. Zhang, S. Zhao, Q. Wang, Q. Zhang, L. Sun, and S. Zhang, “Optimization of Cr4+-doped saturable-absorber Q-switched lasers,” IEEE J. Quantum Electron. 33(12), 2286–2294 (1997). 4. J. Liu, S. Wu, Q. H. Yang, and P. Wang, “Stable nanosecond pulse generation from a graphene-based passively Q-switched Yb-doped fiber laser,” Opt. Lett. 36(20), 4008–4010 (2011). 5. X. Li, Y. Wang, Y. Wang, W. Zhao, X. Yu, Z. Sun, X. Cheng, X. Yu, Y. Zhang, and Q. J. Wang, “Nonlinear absorption of SWNT film and its effects to the operation state of pulsed fiber laser,” Opt. Express 22(14), 17227–17235 (2014). 6. A. S. Kurkov, “Q-switched all-fiber lasers with saturable absorbers,” Laser Phys. Lett. 8(5), 335–342 (2011). 7. H. Zhang, D. Y. Tang, X. Wu, and L. M. Zhao, “Multi-wavelength dissipative soliton operation of an erbiumdoped fiber laser,” Opt. Express 17(15), 12692–12697 (2009). 8. Z. X. Zhang, Z. W. Xu, and L. Zhang, “Tunable and switchable dual-wavelength dissipative soliton generation in an all-normal-dispersion Yb-doped fiber laser with birefringence fiber filter,” Opt. Express 20(24), 26736–26742 (2012). 9. Z. Luo, M. Zhou, J. Weng, G. Huang, H. Xu, C. Ye, and Z. Cai, “Graphene-based passively Q-switched dualwavelength erbium-doped fiber laser,” Opt. Lett. 35(21), 3709–3711 (2010). 10. Z. T. Wang, Y. Chen, C. J. Zhao, H. Zhang, and S. C. Wen, “Switchable Dual-Wavelength Synchronously QSwitched Erbium-Doped Fiber Laser Based on Graphene Saturable Absorber,” IEEE Photon. J. 4(3), 869–876 (2012). 11. D. I. Richardson, R. I. Laming, D. N. Payne, V. Matsas, and M. W. Phillips, “Self-starting, passively modelocked erbium fibre ring laser based on the amplifying Sagnac switch,” Electron. Lett. 27(6), 542–544 (1991). 12. V. J. Matsas, T. P. Newson, and M. N. Zervas, “Self-starting passively mode-locked fibre ring laser exploiting nonlinear polarisation switching,” Opt. Commun. 92(1-3), 61–66 (1992). 13. L. M. Zhao, D. Y. Tang, T. H. Cheng, and C. Lu, “Nanosecond square pulse generation in fiber lasers normal dispersion,” Opt. Commun. 272(2), 431–434 (2007). #226272 $15.00 USD Received 5 Nov 2014; revised 21 Dec 2014; accepted 22 Dec 2014; published 20 Jan 2015 © 2015 OSA 26 Jan 2015 | Vol. 23, No. 2 | DOI:10.1364/OE.23.001353 | OPTICS EXPRESS 1353 14. S. Kobtsev, S. Kukarin, and Y. Fedotov, “Ultra-low repetition rate mode-locked fiber laser with high-energy pulses,” Opt. Express 16(26), 21936–21941 (2008). 15. X. H. Li, X. M. Liu, X. H. Hu, L. R. Wang, H. Lu, Y. S. Wang, and W. Zhao, “Long-cavity passively modelocked fiber ring laser with high-energy rectangular-shape pulses in anomalous dispersion regime,” Opt. Lett. 35(19), 3249–3251 (2010). 16. E. Ding, Ph. Grelu, and J. N. Kutz, “Dissipative soliton resonance in a passively mode-locked fiber laser,” Opt. Lett. 36(7), 1146–1148 (2011). 17. X. Wu, D. Y. Tang, H. Zhang, and L. M. Zhao, “Dissipative soliton resonance in an all-normal-dispersion erbium-doped fiber laser,” Opt. Express 17(7), 5580–5584 (2009). 18. Z. C. Luo, W. J. Cao, Z. B. Lin, Z. R. Cai, A. P. Luo, and W. C. Xu, “Pulse dynamics of dissipative soliton resonance with large duration-tuning range in a fiber ring laser,” Opt. Lett. 37(22), 4777–4779 (2012). 19. N. Zhao, M. Liu, H. Liu, X. W. Zheng, Q. Y. Ning, A. P. Luo, Z. C. Luo, and W. C. Xu, “Dual-wavelength rectangular pulse Yb-doped fiber laser using a microfiber-based graphene saturable absorber,” Opt. Express 22(9), 10906–10913 (2014). 20. J. Albert, L. Shao, and C. Caucheteur, “Tilted fiber Bragg grating sensors,” Laser Photonics Rev. 7(1), 83–108 (2013). 21. J. Zheng, X. Dong, P. Zu, L. Y. Shao, C. C. Chan, Y. Cui, and P. P. Shum, “Magnetic field sensor using tilted fiber grating interacting with magnetic fluid,” Opt. Express 21(15), 17863–17868 (2013). 22. S. C. Kang, S. Y. Kim, S. B. Lee, S. W. Kwon, S. S. Choi, and B. Lee, “Temperature-independent strain sensor system using a tilted fiber Bragg grating demodulator,” IEEE Photon. Technol. Lett. 10(10), 1461–1463 (1998). 23. X. Dong, H. Zhang, B. Liu, and Y. Miao, “Tilted fiber Bragg gratings: principle and sensing applications,” Photon. Sensors 1(1), 6–30 (2011). 24. K. M. Zhou, G. Simpson, X. F. Chen, L. Zhang, and I. Bennion, “High extinction ratio in-fiber polarizers based on 45° tilted fiber Bragg gratings,” Opt. Lett. 30(11), 1285–1287 (2005). 25. C. B. Mou, H. Wang, B. G. Bale, K. M. Zhou, L. Zhang, and I. Bennion, “All-fiber passively mode-locked femtosecond laser using a 45o-tilted fiber grating polarization element,” Opt. Express 18(18), 18906–18911 (2010). 26. Z. Zhang, C. Mou, Z. Yan, K. Zhou, L. Zhang, and S. K. Turitsyn, “Sub-100 fs mode-locked erbium-doped fiber laser using a 45°-tilted fiber grating,” Opt. Express 21(23), 28297–28303 (2013). 27. K. Zhou, L. Zhang, X. Chen, and I. Bennion, “Optic sensors of high refractive-index responsivity and low thermal cross sensitivity that use fiber Bragg gratings of >80 ° tilted structures,” Opt. Lett. 31(9), 1193–1195 (2006). 28. T. Guo, A. Ivanov, C. Chen, and J. Albert, “Temperature-independent tilted fiber grating vibration sensor based on cladding-core recoupling,” Opt. Lett. 33(9), 1004–1006 (2008). 29. X. Chen, K. Zhou, L. Zhan, and I. Bennion, “In-fiber twist sensor based on a fiber Bragg grating with 81 degrees tilted structure,” IEEE Photon. Technol. Lett. 18, 2596–2598 (2006). 30. R. Suo, X. Chen, K. Zhou, L. Zhang, and I. Bennion, “In-fibre directional transverse loading sensor based on excessively tilted fibre Bragg gratings,” Meas. Sci. Technol. 20(3), 034015 (2009). 31. K. Zhou, L. Zhang, X. Chen, and I. Bennion, “Low thermal sensitivity grating devices based on Ex-45 degrees tilting structure capable of forward-propagating cladding modes coupling,” J. Lightwave Technol. 24(12), 5087– 5094 (2006). 32. C. Mou, K. Zhou, Z. Yan, H. Fu, and L. Zhang, “Liquid level sensor based on an excessively tilted fibre grating,” Opt. Commun. 305, 271–275 (2013).


Introduction
Optical pulses with long pulse durations in the nanosecond to millisecond regime are required for many applications, including material processing [1], distance measurements, and remote sensing [2].Q-switched lasers can deliver long pulses with high pulse energies and lower repetition rate (kHz) [3].Although Q-switching can be implemented by either active or passive modulation, passively Q-switched fiber lasers are inherently more attractive as they can provide the desired Q-switched output without the need for external modulation [4,5].From a practical point of view, development of all-fiber Q-switched fiber lasers is the popular modern trend [6], and it is very desirable to implement multi-wavelength and wavelengthswitchable pulsed laser [7,8].A dual-wavelength Q-switched fiber laser with a wavelength spacing of 0.2 nm based on graphene saturable absorber (SA) was reported, by using a fiber Bragg grating with two reflection peaks [9].Benefiting from the birefringence-induced filtering effect, a dual-wavelength Q-switched fiber laser with a graphene SA has also been reported [10].
Besides Q-switched fiber lasers, there has been growing interest in the fact that nanosecond rather than picosecond or femtosecond pulses could also be realized by virtue of peak-power clamping effect in passively mode-locked fiber lasers with extended cavity length.Nanosecond square pulse generation in passively mode-locked fiber lasers was firstly reported with amplifying Sagnac switch by Richardson [11] and nonlinear polarization rotation (NPR) by Matsas [12], respectively.Henceforth, various nanosecond square-wave fiber lasers with different cavity conditions have been demonstrated, such as nanosecond square-profile dissipative soliton laser with all-normal dispersion [13,14], high-energy square-wave pulse laser with large net anomalous dispersion [15], and dissipative soliton resonance lasers [16][17][18].We noted that the most rectangular pulse fiber lasers were under single wavelength operation.Regarding the wavelength versatility of the nanosecond modelocked lasers, a dual-wavelength rectangular pulse ytterbium-doped fiber laser by using a microfiber-based graphene SA was demonstrated [19].The dual-wavelength switchable operation was also achieved.However, the operation wavelengths and wavelength spacing are subjected to the intra-cavity random birefringence.
For the first time to our best knowledge, in this work we proposed and demonstrated a novel kind of pulsed fiber laser, which was Q-switched or mode-locked by using an LA-TFG.The polarization dependence of the LA-TFG can induce NPR effect in the laser cavity, and furthermore polarization-mode splitting enables polarization spectrum filtering.Thus, switchable dual-wavelength Q-switched and mode-locked pulses have been achieved with short and long cavities, respectively.Moreover, the mode-locked laser worked under the generation of nanosecond rectangular pulses, due to the peak-power clamping effect.With the increasing pump power, the durations of single-and dual-wavelength rectangular pulses broaden.The LA-TFG was inscribed in H 2 -loaded standard telecom fiber (SMF-28) by use of a frequency-doubled Ar + laser and the scanning mask technique.A commercial amplitude mask (from Edmund Optics Ltd) with a period of 6.6 μm was utilized for the LA-TFG inscription.Owing to the limited size of the amplitude mask, the effective exposure length of the fiber is only ~12 mm.During the inscription process, the amplitude mask was tilted at ~73° to induce in-fiber fringes blazed at ~78° [32].The spectra of the fabricated 78°-TFGs were examined by use of the broadband light source combined with a polarizer and a polarization controller.The typical measured transmission spectrum of an LA-TFG shows a series of dual-peak resonances in the wavelength range from 1200 nm to 1700 nm with a nearly even separation between adjacent resonances, as shown in the inset of Fig. 1.The zoomed one paired peaks at wavelength of 1554.9 nm and 1561 nm is shown in Fig. 1.When the light is polarized, either the equivalent fast-or the slow-axis mode can be fully excited or eliminated.The blue dotted line indicates the fast-axis mode, while the dashed red line shows the slow-axis mode.The full strength of the loss peak reached ~10 dB when it was fully excited.The black solid curve illustrates excitation of the two modes with un-polarized light.It can be seen that the fabricated LA-TFG features polarization-dependence and polarizationmode splitting.The schematic of the pulsed erbium-doped fiber laser with an LA-TFG is shown in Fig. 2. The laser consists of 1 m erbium-doped fiber (EDF) with nominal absorption coefficient of ~80 dB/m at 1530 nm and normal dispersion β 2 = 66.1 ps 2 /km.The EDF is pumped through a 980/1550 wavelength division multiplexing (WDM) from a grating stabilized 975 nm laser diode (LD), which can provide up to 600 mW pump power.A polarization-independent optical isolator is used to ensure single direction oscillation.An LA-TFG is employed to induce polarization-dependent loss and polarization spectrum filtering.Two in-fiber polarization controllers (PC1and PC2) are located before and after the LA-TFG.A 10:90 fiber coupler is placed after the EDF to tap 10% of laser power out of the cavity.The total cavity length including the EDF and all fiber pigtails of the used components is 2.7 m.The cavity net dispersion is ~-0.004ps 2 .From the existing laser cavity, only Q-switch operation can be achieved.In order to realize mode-locking, a length of 150-m dispersion-shifted fiber (DSF) is incorporated into the cavity to increase the nonlinear effect.The DSF has a dispersion coefficient of −5 ps 2 /km.Then, the total cavity length becomes ~153.7 m, and the cavity net dispersion is ~-0.75 ps 2 .The output pulses were measured with 1-GHz photodetector and 2.5-GHz oscilloscope.Firstly, Q-switching operation was achieved in the case of short cavity.The laser can operate on single-or dual-wavelength Q-switching once the pump power exceeds 275 mW, through adjusting the two PCs. Figure 3 shows the output spectra of the Q-switched pulses at the pump power 295 mW.The single-wavelength Q-switching operation can be switched between the two wavelengths: 1554.9 nm and 1561 nm.And the two simultaneous Qswitching lasing wavelengths for the dual-wavelength operation center at the same two wavelengths.The wavelength spacing is 6.1 nm.The operation wavelengths and wavelength spacing are coincident with the polarization spectrum characteristics of the used LA-TFG.Figure 4 shows the typical oscilloscope trace of single-wavelength Q-switched pulse.The full width at half maximum (FWHM) of the Q-switched pulse is 1.84 μs.The repetition rate of pulse is 175.7 kHz, corresponding to a pulse interval of 5.69 μs. Figure 5 shows the dualwavelength Q-switched pulse train and its single pulse zoom-in.The FWHM is 1.86 μs, which is a little broader than that of single-wavelength case.The repetition rate of pulse is 217.9 kHz, corresponding to a pulse interval of 4.59 μs.The repetition rate difference between single-and dual-wavelength operations is attributed to the different polarization states.To investigate the dynamics of the Q-switched fiber laser, we increase the pump power while keeping the PCs unchanged.The positions and the wavelength separation of the two lasing peak do not depend on the pump power.A 1-nm bandpass tunable optical filter was used to resolve the dual-wavelength output.Pulse train at each wavelength has the same repetition rate as the total dual-wavelength Q-switched pulses.In the case of short cavity, mode-locking could not be obtained.We estimated it is because of too weak saturable absorption effect, since the LA-TFG has a relatively low PDL and short cavity leads to low nonlinearity.To overcome this problem, a length of 150-m DSF was incorporated into the laser cavity.In this case, the mode-locked pulses were obtained as the pump power was increased to 178 mW. Figure 6 presents the typical single-wavelength mode-locked spectra at 1554.8 nm with 0.65-nm bandwidth and 1560.9 nm with 0.43-nm bandwidth at 180 mW pump power.Then the single-wavelength mode-locking in the time domain was investigated by using a high-speed oscilloscope, as shown in Fig. 7.The pulse repetition rate is 1.32 MHz, which is determined by the cavity length.Notably, the pulse profile exhibits rectangular shape on the oscilloscope trace, as shown in Fig. 7(b).The pulse duration is 120.1 ns.It was naturally expected that dual-wavelength passive mode-locking could be achieved as the Q-switch operation.After carefully tuning the two PCs, simultaneous mode-locking at two wavelengths could also be obtained.As can be seen from Fig. 8, the dual-wavelength simultaneously oscillated at 1554.8 and 1560.9 nm.Similar to the singlewavelength case, the pulse profile of dual-wavelength mode-locking also exhibits rectangular shape on the oscilloscope trace, as shown in Fig. 9.The pulse repetition rate is still 1.32 MHz.The difference with single-wavelength mode-locking is the broader pulse duration of 205.8 ns, as presented in Fig. 9(b).Then the pulse evolution with the variation of the pump power was investigated under both single-and dual-wavelength cases.Figure 10(a) shows the single-wavelength pulse broadening when the pump power was increased.The pulse amplitude was almost clamped at a constant level during the pulse broadening.Figure 10(b) shows the experimentally measured pulse duration versus the pump power.As can be seen in Fig. 10(b), the pulse duration varied from 120.1 ns to 154.5 ns as the pump power was enhanced from 180 mW to 580 mW.The radio frequency (RF) spectrum presented in the inset of Fig. 10(b) exhibits an RF signal-tonoise ratio (SNR) over 80 dB, which indicates that the mode-locking pulse is stable under laboratory conditions.Similarly, the duration of the dual-wavelength mode-locked pulse varied from 205.8 ns to 259.1 ns with the pump power increased from 180 mW to 580 mW, with the pulse peak almost clamped at a constant level, as shown in Fig. 11. Figure 11(b) also shows the experimentally measured pulse energy versus the pump power.The pulse energy increased monotonically to 26.7 nJ when the pump power was up to 580 mW.To further study the characteristics of the dual-wavelength mode-locking operation, a bandpass filter with a bandwidth of 1 nm was employed to resolve the lasing at each wavelength.The filtered pulse-trains oscillated at the two wavelengths suggest that the both two wavelengths operated simultaneously and individually in passive mode-locking state.The pulse profiles of the both two wavelengths are still rectangular, but with a little smaller pulse duration than that of dual-wavelength mode-locked pulse.

Conclusions
We have, for the first time to our best knowledge, proposed and demonstrated switchable dual-wavelength Q-switched and mode-locked fiber lasers by using an LA-TFG with unique polarization properties.Q-switched pulses were obtained in the case of short length cavity, while mode-locked pulses were only achieved in the case of long length cavity.Both Qswitching and mode-locking could be operated at switchable single wavelength and dual wavelength.Due to the peak-power clamping effect, the mode-locked laser radiates nanosecond rectangular pulses.The duration of the rectangular pulse broadens with the increasing pump power.

Fig. 1 .
Fig. 1.Measured transmission of the LA-TFG from 1550 nm to 1575 nm range under different polarization excitation (the inset is transmission spectrum from 1200 nm to 1700 nm).

Fig. 3 .
Fig.3.Spectra of single-wavelength (black dotted line at 1554.9 nm, blue dashed line at 1561 nm) and dual-wavelength (red solid line) Q-switched pulses.

Fig. 10 .Fig. 11 .
Fig. 10.(a) Single-wavelength pulse broadening with the pump power increased, (b) measured pulse width versus the pump power (the inset of is RF spectrum).(b)