Experimental demonstration of optical switching and routing via four-wave mixing spatial shift

We demonstrate the shift characteristics of four-wave mixing (FWM) beam spots which are controlled by the strong laser fields via the large cross-Kerr nonlinearity. The shift distances and directions are determined by the nonlinear dispersions. Based on such spatial displacements of the FWM beams, as well as the probe beam, we experimentally demonstrate spatial optical switching for one beam or multiple optical beams, which can be used for all-optical switching, switching arrays and routers. ©2010 Optical Society of America OCIS codes: (060.1810) Couplers, switches, and multiplexers; (190.0190) Nonlinear optics; (190.3270) Kerr effect; (190.4180) Multiphoton processes; (190.4223) Nonlinear wave mixing; (250.6715) Switching; (270.1670) Coherent optical effects. References and links 1. A. M. C. Dawes, L. Illing, S. M. Clark, and D. J. Gauthier, “All-optical switching in rubidium vapor,” Science 308(5722), 672–674 (2005). 2. A. W. Brown, and M. Xiao, “All-optical switching and routing based on an electromagnetically induced absorption grating,” Opt. Lett. 30(7), 699–701 (2005). 3. M. Yan, E. G. Rickey, and Y. F. Zhu, “Observation of Absorptive Photon Switching by Quantum Interference,” Phys. Rev. A 64(4), 041801 (2001). 4. Y. P. Zhang, Z. Q. Nie, H. B. Zheng, C. B. Li, J. P. Song, and M. Xiao, “Electromagnetically Induced Spatial Nonlinear Dispersion of Four-Wave Mixing,” Phys. Rev. A 80(1), 013835 (2009). 5. H. Wang, D. Goorskey, and M. Xiao, “Enhanced Kerr nonlinearity via atomic coherence in a three-level atomic system,” Phys. Rev. Lett. 87(7), 073601 (2001). 6. M. Xiao, Yq. Li, Sz. Jin, and J. Gea-Banacloche, “Measurement of Dispersive Properties of Electromagnetically Induced Transparency in Rubidium Atoms,” Phys. Rev. Lett. 74(5), 666–669 (1995). 7. G. P. Agrawal, “Induced focusing of optical beams in self-defocusing nonlinear media,” Phys. Rev. Lett. 64(21), 2487–2490 (1990). 8. J. M. Hickmann, A. S. Gomes, C. de Araújo, “Observation of spatial cross-phase modulation effects in a self-defocusing nonlinear medium,” Phys. Rev. Lett. 68(24), 3547–3550 (1992). 9. Y. P. Zhang, U. Khadka, B. Anderson, and M. Xiao, “Temporal and Spatial Interference between Four-Wave Mixing and Six-Wave Mixing Channels,” Phys. Rev. Lett. 102(1), 013601 (2009). 10. B. S. Ham, and P. R. Hemmer, “Coherence switching in a four-level system: quantum switching,” Phys. Rev. Lett. 84(18), 4080–4083 (2000). 11. J. P. Zhang, G. Hernandez, and Y. F. Zhu, “Optical switching mediated by quantum interference of Raman transitions,” Opt. Express 16(23), 19112–19117 (2008). 12. R. M. Camacho, P. K. Vudyasetu, and J. C. Howell, “Four-Wave-Mixing Stopped Light in Hot Atomic Rubidium Vapour,” Nat. Photonics 3(2), 103–106 (2009). 13. V. Boyer, A. M. Marino, R. C. Pooser, and P. D. Lett, “Entangled images from four-wave mixing,” Science 321(5888), 544–547 (2008).


Introduction
In order to develop the next generation of all-optical communication and computing, certain optical elements are essential, such as all-optical switches and routers.There have been several new schemes reported recently to demonstrate, in principle, such all-optically controlled switching and routing functions [1][2][3].A weak beam was used to selectively turn on/off the spots in the spatial pattern of a stronger laser beam via cross-phase modulation (XPM) in a two-level atomic medium [1], showing a spatial switching effect.Also, controlling the linear [2] and nonlinear [3] optical absorptions of one laser beam by another in coherently-prepared atomic media was exploited to show all-optically controlled beam switching.Recently, it was shown that a four-wave mixing (FWM) signal beam can be spatially shifted easily by frequency detunings and intensities of the dressing laser beams following a dispersion-like behavior [4].Such electromagnetically-induced spatial dispersion (EISD) is greatly enhanced same as for the frequency (linear and nonlinear) dispersions in the electromagnetically induced transparency (EIT) systems [5,6], which can give large and sensitive spatial displacements for the FWM and the probe beams.Also, if one carefully chooses the parametric regime, the probe and FWM beams can have focusing effects in a self-defocusing medium due to the strong XPM [7,8], which compensate the beam diffraction when propagating through the long atomic medium.
In this Letter, we show that by making use of the EISD effect in a three-level ladder-type atomic system [4], all-optical switching/routing effects can be experimentally demonstrated.The FWM signals are generated by two coupling beams in the three-or two-level system, with an additional dressing field to shift the spatial location of the generated FWM beams.The intensities of the initial (before shifting) and final (after shifting) spots of the FWM signals correspond to the "off" and "on" states of the switch.Different shift directions and spot locations are studied as functions of experimental parameters.Since there are two FWM beams and each beam has more than one final states (spatial locations), it is possible to construct switching arrays in the current system.Such controllable spatial beam spot shifts can provide potential architectures for beam address selection and routing in all-optical communication and networks.

Theoretical model and experimental scheme
G′ ) are added, which are from the other dye laser with similar characteristics as the first one, also connecting the transition between 0 to 1 . 1 E adds onto beam 1 and 1 E′ (beam 2) propagates in another plane (xz) which is perpendicular to the yz plane with a small angle relative to 1 E , as shown in the inset of Fig. 1(c).When 1 E , 1 E′ and 3 E are turned on simultaneously with blocking 2 E , 2 E′ , a DFWM process is generated satisfying the phase-matching condition E beam is influenced by the combined effect of 1 E′ and 2 E′ beams but mainly shifted horizontally by 1 E′ beam (Fig. 3(a)).Thus, a pair of 3 E and 2 F E beams can be switched on and off by 1 E′ beam, while one 1 F E beam can be switched on and off by 2 E′ beam at the same time.The theoretical description of the spatial properties of the beams 3, 1, 2

1(b)). Here we define detuning
due to self-and cross-Kerr nonlinearities can be given through numerically solving the following propagation equations: where 3 / ,

D
are the parameters related to the Rabi frequency of the dressing field, the frequency detuning, and the atomic coherence rate.3 µ ( ij µ ) is the dipole matrix element between the states coupled by the probe beam 3 E (between | i > and | j > ).By assuming Gaussian profiles for the input fields, Eqs. ( 1)-( 3) are solved by the split-step method.∆ is shown in Fig. 2(a).The moving trace of the light spot is dispersion-like as frequency scans [4].It means 2 F E beam can have right or left shift.There are two maximal displacements corresponding to the positive maximum nonlinear refraction coefficient and the negative maximum coefficient.Without 1 E′ beam, the probe field 3 E and 2 F E are single strong spots, as shown in Fig. 3(a).When the dressing field 1 E′ is on, the intensities of the probe and 2 F E beams become weaker [9] and are shifted (one to the right and another to the left of the original position).Since we use one more mirror in the probe beam scheme than that of 2 F E , they have opposite direction of shift on CCD screen (Fig. 3(a)).In fact, in the heated pipe both two beams have right shift, as shown in Fig. 3(b, c).Larger spatial shift occurs with an increasing 1 E′ intensity, which can be understood from the expression:

Optical switching and routing via spatial shift
The nonlinear phase shift NL ϕ is directly proportional to the dressing intensity 1 I ′ .The component of the wave vector of the shows the dressing field dependences of the spatial shifts based on the numerical calculation and the experimental measurements.Figure 2(c) presents the temperature dependence (atomic density N) of the shift curves for the theoretical and the experimental results, respectively.We see that increasing the atomic density equals to increasing propagation distance z, and the shift of the spot becomes larger.
So, as shown above the beam spots can have different spatial shifts with different experimental parameters (such as frequency, intensity, and atomic density), which can correspond to different on-off combinations.The switching or routing time is the rising and falling times of the switch-in and switch-out signal.The cross-Kerr refractive index change (  E′ off and on as the laser frequency detuning is tuned to get the maximal spatial displacement.When a spot stays at its initial position, it means that the switch is in the "off" state.When the frequencies of the probe and 2 F E beams are set at their peak shift positions, the light spots will have their largest shifts, so the switch stands at its "on"-state.Such two states form two ports of the optical switch.The upper spot is the 2 F E beam and the lower spot is the probe beam.Initially, two spots are set at same vertical line without the dressing laser beam.As the dressing beam 1 E′ turns on, the upper spot moves to the left side and the lower spot moves to the right side, both of which leave their initial positions completely.The switching contrast can be defined as "off"-state and on I is the light intensity at the "on"-state.The contrast derived from the experiment is about 92% C = . This experiment provides a physical mechanism to realize an all-optical switching/routing by controlling the dressing laser beam. A chopper is used to control the dressing field, subtracting the laser pulse repetition time of 0.1s, which is considered as an idle load state.The laser pulse width is 5ns.The detected switching time is limited by the response time of the CCD, which is about 3µs, far larger than the laser pulse width.Thus, the switching speed in the current experiment is greatly constrained as shown in Figs. 3 (b) and (c).The on-state just lasts 5ns, followed by a 3µs rising time, and then a 5ns off-state, followed by a 3µs falling time, and so on.Since the spatial displacements of the probe and  E beams, to achieve a triple binary optical switch.The initial locations of the spots are the "off" states and the switches are considered to come to their "on" states when the spots shift away to new locations.The repetition frequency of the chopper is much longer than 5 ns pulse-width of the dressing laser, so the "on"-state lasts several 5ns intervals and then turns to the "off"-state.In Fig. 4, at 1 18GHz ∆ = − for the self-focusing side and temperature 250°C, when 1 E′ is on, the probe and E′ , respectively, we can use two controllable parameters, i.e. the frequency and intensity of the laser, to control the different shifts of the three spots.Such simultaneous optical switching for three beams can perform the functions of choosing different addresses in data transmissions and can be used as the optical routings, the multiplexer or all-optical switching arrays for all-optical networks.
In the above discussion, we have controlled the probe, E are shifted towards the opposite directions (Fig. 4).Actually, such three beams can also be shifted to the same direction when the sign of the cross Kerr-nonlinear coefficient of the The advantages of solids include high density of atoms, compactness, and absence of atomic diffusion, but with relatively broad optical linewidths and fast decoherence rates.However, there are still many advantages to study all-optical switching, especially spatial all-optical switching and routing, using multi-level atomic media via EIT (or atomic coherence) related effects.The current atomic experiment has several easily tunable experimental parameters (such as laser intensities, frequency detunings, and atomic density), which provide a much better platform (compared to the solid systems) to study the formation and dynamics of the novel spatial optical switch and router protocols.Also, there is a narrow linewidth (compared to the solid systems) in an atomic media.

Conclusion
In conclusion, we experimentally demonstrated the spot shifts of the FWMs and probe laser beams, which can be used as the "on" and "off" states of the spatial all-optical switch.Several experimental parameters (such as frequency detunings, intensities and temperature) have been used to optimize the beam shift distances and directions, so the extinction ratio for the on/off states can be optimized.At the same time, the opposite-direction shifting has been realized simultaneously for different FWM beams, which could be employed to construct switching/routing arrays.The current experiment also opens the door for spatial manipulations of FWM signal beams in optical imaging storage [12], quantum correlation [13], all-optical computation, and future all-optical networking.

Fig. 1 .
Fig. 1.(a) and (b) The diagrams of Na energy levels with different coupling schemes.The bold arrows refer to the dressing fields.(c) The experimental scheme and arrangements (Inset: the spatial alignments of the incident beams).The relevant experimental system is shown in Figs.1(a) and (b).Three energy levels from sodium atoms (in a heat-pipe oven of length 18 cm) are involved in the experimental schemes.The pulse laser beams are aligned spatially as shown in Fig.1(c).In Fig.1(a), energy levels 0 ( 1/ 2 3S ), 1 ( 3/ 2 3P ) and 2 ( 3/ 2 4D ) form a ladder-type three-level atomic system.Coupling field 2 E (wavelength of 568.8nm, angular frequency 2

ω
ξ are the longitudinal and transverse coordinates, respectively.0 n is the linear refractive index at 1 − are the cross-Kerr coefficients of 1,2 E and 1,2 E′ , respectively.Generally, the Kerr coefficient can be defined by

Fig. 2 . 2 FE. 1 E′ , the spatial shift of 2 FE
Fig. 2. (a) Spatial dispersion curves of 2 F E in the ladder-type three-level system versus 1 ∆

2 FE
Figure 2(b)  shows the dressing field dependences of the spatial shifts based on the numerical calculation and the experimental measurements.Figure2(c) presents the temperature dependence (atomic density N) of the shift curves for the theoretical and the experimental results, respectively.We see that increasing the atomic density equals to increasing propagation distance z, and the shift of the spot becomes larger.So, as shown above the beam spots can have different spatial shifts with different experimental parameters (such as frequency, intensity, and atomic density), which can correspond to different on-off combinations.The switching or routing time is the rising and falling times of the switch-in and switch-out signal.The cross-Kerr refractive index change (

1 F E and 2 FEFig. 3 . 2 FE
Fig. 3. (a) Results of the optical switches and the spot shifts of the probe (lower) and 2 F E

Figure 3 ( 2 FE
Figure 3 (a) shows the two states of the probe and 2 F E beams by switching the strong laser beam 1E′ off and on as the laser frequency detuning is tuned to get the maximal spatial displacement.When a spot stays at its initial position, it means that the switch is in the "off" state.When the frequencies of the probe and intensity at the (C) 2010 OSA 18 January 2010 / Vol. 18, No. 2 / OPTICS EXPRESS 903

1 FE
signal is opposite to those of the 2 F E (probe) beams at the proper laser detuning.So, each spot can have left and right locations.Including the initial position, every spot has three possible spatial locations.Totally there are 3 × 3 controllable spatial positions.It can such achieve a switch array.