Volume extreme ultraviolet holographic imaging with numerical optical sectioning

Three dimensional images were obtained using a single high numerical aperture hologram recorded in a high resolution photoresist with a table top λ = 46.9 nm laser. Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance in the numerical reconstruction algorithm, allowing numerical optical sectioning. A robust three dimension image of a test object was obtained with numerical optical sectioning, providing a longitudinal resolution of approximately 2 μm and a lateral resolution of 164 nm. ©2007 Optical Society of America OCIS codes: (090.0090) Holography; (100.2960) Image analysis References and Links 1. J. E. Trebes, S. B. Brown, E. M. Campbell, D. L. Matthews, D. G. Nilson, G. F. Stone, and D. A. Whelan, “Demonstration of X-Ray holography with an X-Ray laser,” Science 238, 517-519 (1987). 2. S. Lindaas, M. Howells, C. Jacobsen and A. Kalinovsky. “X-ray holographic microscopy by means of photoresist recording and atomic force microscope readout,” J. Opt. Soc. Am. A 13, 1788-1800 (1996). 3. I. McNulty, J. Kirz, C. Jacobsen, E. Anderson, M. R. Howells, and D. P. Kern, “High resolution imaging by Fourier Transform X-ray holography,” Science 256, 1009-1012 (1992). 4. C. Jacobsen, M. Howells, J. Kirz, and S. Rothman, “X-ray holographic microscopy using photoresist,” J. Opt. Soc. Am. A 7, 1847-1861 (1990). 5. I. McNulty, “The future of X-ray holography,” Nucl. Instrum. Methods Phys. Res. A 347, 170-176 (1994). 6. S. Eisebitt, J. Lüning, W. F. Schlotter, M. Lörgen, O. Hellwing, W. Eberhardt and J. Stöhr, “Lensless imaging of magnetic nanostructures by X-ray spectro-holography,” Nature 432, 885-888 (2004). 7. R. A. Bartels, A. Paul, H. Green, H. C. Kapteyn, M. M. Murnane, S. Backus, I. P. Christov, Y. W. Liu, D. Attwood, and C. Jacobsen. “Generation of spatially coherent light at extreme ultraviolet wavelengths,” Science 297, 376-378 (2002). 8. A. S. Morlens, J. Gautier, G. Rey, P. Zeitoun, J. P. Caumes, M. Kos-Rosset, H. Merdji, S. Kazamias, K. Cassou and M. Fajardo, “Submicrometer digital in-line holographic microscopy at 32 nm with high-order harmonics,” Opt. Lett. 31, 3095-3097 (2006). 9. R. I. Tobey, M. E. Siemens, O. Cohen, M. M. Murnane, H. C. Kapteyn and K. A. Nelson, “Ultrafast extreme ultraviolet holography: dynamic monitoring of surface deformation,” Opt. Lett. 32, 286-288 (2007). 10. C. D. Macchietto, B. R. Benware and J. J. Rocca, “Generation of millijoule-level soft-X ray laser pulses at a 4-Hz repetition rate in a highly saturated tabletop capillary discharge amplifier,” Opt. Lett. 24, 1115-1117 (1999). 11. Y. Wang, M. A. Larotonda, B. M. Luther, D. Alessi, M. Berrill, V. N. Shlyaptsev, and J. J. Rocca, “Demonstration of high-repetition-rate tabletop soft-x-ray lasers with saturated output at wavelengths down to 13.9 nm and gain down to 10.9 nm,” Phys. Rev. A 72 Art. No. 053807 (2005). 12. G. Vaschenko, C. Brewer, F. Brizuela, Y. Wang, M. A. Larotonda, B. M. Luther, M. C. Marconi, J. J. Rocca, C. S. Menoni, E. H. Anderson, W. Chao, B. D. Harteneck, J. A. Liddle, Y. Liu, D. T. Attwood. “Sub38 nm resolution table-top microscopy using 13 nm wavelength laser light,” Opt. Lett. 31, 1214-1216 (2006). 13. G. Vaschenko, F. Brizuela, C. Brewer, M. Grisham, H. Mancini, C. S. Menoni, M. C. Marconi, J. J. Rocca, W. Chao, A. Liddle, E. Anderson, D. Attwood, A. V. Vinogradov, I. A. Artioukov, Y. P. Pershyn and V. V. Kondratenko. “Nano-imaging with a compact extreme ultraviolet laser,” Opt. Lett. 30, 2095-2097 (2005). 14. F. Brizuela, G. Vaschenko, C, Brewer, M. Grisham, C. S. Menoni, M. C. Marconi, J. J. Rocca, W. Chao, J. A. Liddle, E. H. Anderson, D. T. Attwood, A. V. Vinogradov, I. A. Artiukov, Y. P. Pershing and V. V. Kondratenko, “Reflection Mode Imaging with Nanoscale Resolution using a Compact Extreme Ultraviolet Laser,” Opt. Express 13, 3983-3988 (2005). 15. B. R. Benware, C. D. Macchietto, C. H. Moreno, and J. J. Rocca, “Demonstration of a high average power tabletop soft X-ray laser,” Phys. Rev. Lett. 81, 5804-5807 (1998). 16. J. J. Rocca, “Table-top soft x-ray lasers,” Rev. Sci. Instrum. 70, 3799-3827 (1999). #84017 $15.00 USD Received 11 Jun 2007; revised 27 Jul 2007; accepted 31 Jul 2007; published 7 Aug 2007 (C) 2007 OSA 20 August 2007 / Vol. 15, No. 17 / OPTICS EXPRESS 10622 17. J. J. Rocca, D. P. Clark, J. L. A. Chilla, V. N. Shlyaptsev, “Energy extraction and achievement of the saturation limit in a discharge-pumped table-top soft x-ray amplifier,” Phys. Rev. Lett. 77, 1476-1479 (1996). 18. P. W. Wachulak, R. A. Bartels, M. C. Marconi, C. S. Menoni and J. J. Rocca. “Sub-400 nm spatial resolution extreme ultraviolet holography with table top laser,” Opt. Express 14, 9636-9642 (2006). 19. Center for X-Ray Optics. http://www-cxro.lbl.gov. 20. Suspension 2.62% in water of latex spheres from Polysciences Inc., diameter 465 nm. 21. U. Schnars and P. O. Jüptner, “Digital recording and reconstruction of holograms in hologram interferometry and shearography,” Appl. Opt. 33, 4373-4377 (1994). 22. U. Schnars and P. O. Jüptner, “Digital recording and numerical reconstruction of holograms,” Meas. Sci. Technol. 13, R85-R101 (2002). 23. J. W. Goodman, Introduction to Fourier Optics (McGraw Hill, 1996), Chap 4, p. 66. 24. G. L. Rogers. “Gabor diffraction microscopy. The hologram as a generalized zone-plate,” Nature 166, 236237 (1950). 25. Attwood, Soft X-ray and extreme ultraviolet radiation, (Cambridge University Press. 1999), Chap. 9, p. 361.


Introduction
Holographic imaging in the soft X-ray (SXR) and extreme ultraviolet (EUV) have been demonstrated in several experiments realized using EUV/SXR lasers and synchrotron sources.These include the first realization of soft X-ray laser holography at Lawrence Livermore National Laboratory using a large laser facility, and the holographic recording of biological samples and sub-micron structures using soft X-ray radiation from synchrotrons, among other experiments [1], [2].A key idea in these experiments is to use coherent short wavelength illumination to achieve a spatial resolution beyond the reach of visible light.
Using synchrotron radiation Gabor and Fourier holograms have been demonstrated [2] with spatial resolution below 100 nm at SXR wavelengths.Compact EUV sources based on high harmonic generation (HHG) were also used to demonstrate table-top in-line EUV holography with a spatial resolution of 7.9 m and 0.8 m.Time resolved holographic imaging, that exploits the short pulsewidth of the HHG sources, was also implemented to study the ultrafast dynamics of surface deformation with a lateral resolution of the order of 100 nm [3], [5].The recent development of compact coherent EUV laser sources, [6] has opened new opportunities for the implementation of novel imaging schemes with nanometer-scale resolution that fit on a table-top [2], [6].In this paper, we present a proof of principle experiment in which we demonstrate that three dimensional imaging in a volume may be obtained from a single high numerical aperture (NA) hologram obtained with a table top EUV laser.Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.
Holographic imaging in the soft X-ray (SXR) and extreme ultraviolet (EUV) have [7] been demonstrated in several experiments realized using EUV/SXR lasers and synchrotron sources.These include the first realization of soft X-ray laser holography at Lawrence Livermore National Laboratory using a large laser facility, and the holographic recording of biological samples and sub-micron structures using soft X-ray radiation from synchrotrons, among other experiments [9], [10].A key idea in these experiments is to use coherent short wavelength illumination to achieve a spatial resolution beyond the reach of visible light [8].
Using synchrotron radiation Gabor and Fourier holograms have been demonstrated with spatial resolution below 100 nm at SXR wavelengths.Compact EUV sources based on high harmonic generation (HHG) were also used to demonstrate table-top in-line EUV holography with a spatial resolution of 7.9 m and 0.8 m.Time resolved holographic imaging, that exploits the short pulsewidth of the HHG sources, was also implemented to study the ultrafast dynamics of surface deformation with a lateral resolution of the order of 100 nm.The recent development of compact coherent EUV laser sources has opened new opportunities for the implementation of novel imaging schemes with nanometer-scale resolution that fit on a table-top.In this paper, we present a proof of principle experiment in which we demonstrate that three dimensional imaging in a volume may be obtained from a single high numerical aperture (NA) hologram obtained with a table top EUV laser.Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.
Holographic imaging in the soft X-ray (SXR) and extreme ultraviolet (EUV) have been demonstrated in several experiments realized using EUV/SXR lasers and synchrotron sources.These include the first realization of soft X-ray laser holography at Lawrence Livermore National Laboratory using a large laser facility, and the holographic recording of biological samples and sub-micron structures using soft X-ray radiation from synchrotrons, among other experiments.A key idea in these experiments is to use coherent short wavelength illumination to achieve a spatial resolution beyond the reach of visible light.
Using synchrotron radiation Gabor and Fourier holograms have been demonstrated with spatial resolution below 100 nm at SXR wavelength.Compact EUV sources based on high harmonic generation (HHG) were also used to demonstrate table-top in-line EUV holography with a spatial resolution of 7.9 m and 0.8 m.Time resolved holographic imaging, that exploits the short pulsewidth of the HHG sources, was also implemented to study the ultrafast dynamics of surface deformation with a lateral resolution of the order of 100 nm.The recent development of compact coherent EUV laser sources has opened new opportunities for the implementation of novel imaging schemes with nanometer-scale resolution that fit on a table-top.In this paper, we present a proof of principle experiment in which we demonstrate that three dimensional imaging in a volume may be obtained from a single high numerical aperture (NA) hologram obtained with a table top EUV laser.Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.
Holographic imaging in the soft X-ray (SXR) and extreme ultraviolet (EUV) have been demonstrated in several experiments realized using EUV/SXR lasers and synchrotron sources.These include the first realization of soft X-ray laser holography at Lawrence Livermore National Laboratory using a large laser facility, and the holographic recording of biological samples and sub-micron structures using soft X-ray radiation from synchrotrons, among other experiments.A key idea in these experiments is to use coherent short wavelength illumination to achieve a spatial resolution beyond the reach of visible light.
Using synchrotron radiation Gabor and Fourier holograms have been demonstrated with spatial resolution below 100 nm at SXR wavelength.Compact EUV sources based on high harmonic generation (HHG) were also used to demonstrate table-top in-line EUV holography with a spatial resolution of 7.9 m and 0.8 m.Time resolved holographic imaging, that exploits the short pulsewidth of the HHG sources, was also implemented to study the ultrafast dynamics of surface deformation with a lateral resolution of the order of 100 nm.The recent development of compact coherent EUV laser sources has opened new opportunities for the implementation of novel imaging schemes with nanometer-scale resolution that fit on a table-top.In this paper, we present a proof of principle experiment in which we demonstrate that three dimensional imaging in a volume may be obtained from a single high numerical aperture (NA) hologram obtained with a table top EUV laser.Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.
Holographic imaging in the soft X-ray (SXR) and extreme ultraviolet (EUV) have been demonstrated in several experiments realized using EUV/SXR lasers and synchrotron sources.These include the first realization of soft X-ray laser holography at Lawrence Livermore National Laboratory using a large laser facility, and the holographic recording of biological samples and sub-micron structures using soft X-ray radiation from synchrotrons, among other experiments.A key idea in these experiments is to use coherent short wavelength illumination to achieve a spatial resolution beyond the reach of visible light.
Using synchrotron radiation Gabor and Fourier holograms have been demonstrated with spatial resolution below 100 nm at SXR wavelength.Compact EUV sources based on high harmonic generation (HHG) were also used to demonstrate table-top in-line EUV holography with a spatial resolution of 7.9 m and 0.8 m.Time resolved holographic imaging, that exploits the short pulsewidth of the HHG sources, was also implemented to study the ultrafast dynamics of surface deformation with a lateral resolution of the order of 100 nm.The recent development of compact coherent EUV laser sources has opened new opportunities for the implementation of novel imaging schemes with nanometer-scale resolution that fit on a table-top.In this paper, we present a proof of principle experiment in which we demonstrate that three dimensional imaging in a volume may be obtained from a single high numerical aperture (NA) hologram obtained with a table top EUV laser.Gabor holograms were numerically reconstructed over a range of image planes by sweeping the propagation distance.

Experimental Details
The experimental set up is schematically illustrated in Fig. 1.A compact α = 46.9nm table top discharge-pumped capillary Ne-like Ar laser occupying only a 1 0.5 m2 footprint on an optical table was used for the recording of the hologram.

Some Extra Details
Lasing was obtained in the 46.9 nm 3s 1P1 3p 1S0 transition of neon-like Ar by exciting Ar filled alumina capillaries 3.2 mm in diameter with a current pulse having an amplitude of 10% to 90% rise time of first half-cycle duration.

Even more details
The pulse generator consists of a 4 stages Marx generator charged at voltages around 45 kV.The fast current pulse was produced by discharging a water dielectric cylindrical capacitor through a spark gap switch connected in series with the capillary load.The current pulse rapidly compresses the plasma column to achieve a dense and hot filamentary plasma channel where a population inversion is created by strong monopole electron impact excitation of the laser upper level and rapid radiative relaxation of the laser lower level.The water serves as a liquid dielectric for the capacitor and also cools the capillary.

2.1.1.a. A continuous
Flow of Ar is injected in the front of the capillary and an optimum Ar gas pressure of 490 mTorr is maintained in the capillary channel.The EUV laser and the vacuum chamber where the hologram was exposed, are connected via a vacuum manifold that provides differential pumping of the chamber that is maintained at 10-5 Torr.The laser, operated with 18.4 cm long capillaries, produces 0.1J pulses at a repetition rate of 1 Hz 15.The high temporal and spatial coherence of the EUV table top laser permits the recording of large NA holograms for high resolution holographic imaging 18.The test object used in the holographic volume imaging experiment consisted of a tilted metallic surface covered with opaque spherical objects as can be seen in ( 1).This test object was fabricated placing a 100 nm thick aluminum foil covering a hole 1.5 mm in diameter made in a 80 m thick mylar sheet.The hole was partially covered with a second mylar sheet 80 m thick, as schematically indicated in Fig. 2. Humanoid robots have received much attention recently.Although they are able to walk without falling, their movements are not natural looking.In order for these robots to move more like humans, two technological obstacles need to be addressed: Firstly, there is a lack of flexibility in their body torsos.In all human activities, movements from the spine are involved.Yet, this important factor has been neglected by the majority of humanoid robotic researchers.One of the main reasons is that the added degrees of freedom (DOF) make it more costly and difficult to build a robot.Another key issue is that it is very difficult to program these types of robots so that they can maintain balance.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.This numerical sectioning technique for Fig. 2. Lasing was obtained in the 46.9 nm 3s 1P1 3p 1S0 transition of neon-like Ar by exciting Ar filled alumina capillaries 3.2 mm in diameter with a current pulse having an amplitude Lasing was obtained in the 46.9 nm 3s 1P1 3p 1S0 transition of neon-like Ar by exciting Ar filled alumina capillaries 3.2 mm in diameter with a current pulse having an amplitude holography is verified to produce a robust three dimension image of a test object.This numerical sectioning technique for holography is verified to produce a robust three dimension image of a test object.
In order to address the above technological challenges, we need to develop flexible spine humanoid robots as experimental platforms.Recently, a few researchers have developed several spinal robots based on the anatomy of the human skeleton, Mizuuchi built a tendon-driven robot called "Kenta" [1], [2].Although the robot has a spine, there has been no data to show that it can move in a flexible way.Also, the robot cannot stand up without external support because the upper body is too heavy [2].Mizuuchi later improved his prototype.However, it is also unable to stand up without external support [3], [5].
At the German Space Agency (DLR), Hirzinger and his group developed a spine robot called "Justin".The robot has a 3-DOF movable upper-torso, two arms and dexterous hands.Unlike the tendon-based robots developed by Mizuuchi and his colleagues, each controllable spinal joint of Justin is directly actuated by a DC Motor via a Harmonic Drive Gear.In order to prevent the robot from falling, the designers fixed the robot to a large platform [6].In November, 2007, researchers from Sugano Lab of Waseda University announced a new humanoid robot for household work and home care.The robot is called "Twendy-One".It has a 4-DOF spine but it is fixed on a wheeled mobile platform.Thus, balancing is not an issue for this robot.It has a 4-DOF spine but it is fixed on a wheeled mobile platform.Thus, balancing is not an issue for this robot.
Inspired by the flexibility of belly dancers, Or conducted the first scientific study on belly dancing [7].He developed a database of belly dancing movements using computer animations.Later, Or recorded the movements of a professional belly dancer using a 12-camera VICON [4] motion capture system.By analyzing the movements of the dancer, he developed a spinal mechanism which allows a full-body humanoid robot to exhibit all the human spine motions in 3D although with less degree of freedom [8].Moreover, the robot is able to stand up while performing dynamic torso motions without external support.In terms of controlling the mechanical spine, Or used a model of the lamprey central pattern generator.Experimental results showed that by using such neural networks, only three control parameters are needed to generate all human spinal motions.
In order to conduct research on human-robot interactions, Or developed a new, full-body flexible spine humanoid robot [9], [10].Experimental results showed that it is possible for humans to perceive emotions expressed by a flexible spine humanoid robot.Later, Or developed the world's first humanoid robot that can walk more naturally, like a human, with flexible spinal motions.The aluminum foil contours over the semicircular aperture to produce a variable height surface with the desirable characteristics for this test in Table I.The 100 nm aluminum foil has a transmission of approximately 35% at α = 46.9nm considering the layer of native oxide 19 and effectively cuts the lower photon energy plasma emission from the Ar discharge in the laser source.The sample was immersed in a solution of MIBK-methyl isobutyl ketone (4-Methyl-2-Pentanone) with IPA (isopropyl alcohol) 1:3 for 30 seconds, rinsed with IPA for 30 seconds, and was finally dried

Results
We adjusted the1 exposure so that the photoresist operated in a linear response regime.With exposure by the EUV laser, the holographic interference pattern generated by the reference and the object beams was recorded in the photoresist and converted to a surface modulation after the development.Thus, the holograms were recorded as a relief pattern in the surface of a photoresist deposited on a Si wafer.
• Weight parameters for the simulated robot.
• Length of each body link.
• Specifications of body joints.Upper Torso means the spine.Due to symmetry, body parts from the right are not shown.• Neuron parameters.Θ is the threshold, Γ is the gain.τ D and τ A are respectively the time constant of the dendritic sums and that of the frequency adaptation.µ is the coefficient of frequency adaptation.
Holograms recorded in such a fashion can not be reconstructed in the conventional way with an optical reconstruction beam.In order to numerically reconstruct the holograms, the surface modulation was digitized with a Novascan atomic force microscope (AFM) operated in tapping mode.Holograms recorded in such a fashion can not be reconstructed in the conventional way  with an optical reconstruction beam.In order to numerically reconstruct the holograms, the surface modulation was digitized with a Novascan atomic force microscope (AFM) operated in tapping mode.
1) Screenshot of the Webots simulation environment.
2) Schematic diagram of the simulated robot.
3) Schematic of the model lamprey CPG.Connections with a dot ending represent inhibitory connections while those with an arrow ending represent excitatory connections.4) Sample output of a segmental oscillator (the 20th segment from the CPG).MNl and MNr respectively represents the output from the left and right motoneurons.Note the regularity of the neural pulses.
Two holograms digitized in this manner are displayed in Fig. 2. The digital reconstruction of the hologram digitized by the AFM is based on a numerical Fresnel propagator in Table II and III.To obtain the amplitude and the phase distribution of the field in the image plane, the field emerging from the hologram illuminated by a plane wave is back propagated with the Fresnel-Kirchhoff integral.The integral was evaluated by the product of the spatial frequency representation of the hologram obtained through a two dimensional fast Fourier transformation and the quadratic phase free space Fresnel propagator in the spatial frequency domain.

Theorem 1 (Einstein-Podolsky-Rosenberg):
The back-propagation distance is determined by calculating the Fresnel zone plate (FZP) focal distance for the specific hologram geometry.For the specific geometry employed in this experiment, the FZP focal length is approximately the distance between the object and the recording medium.The digital images of the holograms processed with the Fresnel propagation code generated the reconstructed images shown in Fig. 2.
Holograms recorded in such a fashion can not be reconstructed in the conventional way with an optical reconstruction beam.In order to numerically reconstruct the holograms, the surface modulation was digitized with a Novascan atomic force microscope operated in tapping mode.

Lemma 1:
The back-propagation distance is determined by calculating the Fresnel zone plate (FZP) focal distance for the specific hologram geometry For the specific geometry employed in this experiment, the FZP focal length is approximately the distance between the object and the recording medium.The digital images of the holograms processed with the Fresnel propagation code generated the reconstructed images shown in Fig. 2.
Holograms recorded in such a fashion can not be reconstructed in the conventional way with an optical reconstruction beam.In order to numerically reconstruct the holograms.

Proof:
The back-propagation distance is determined by calculating the Fresnel zone plate (FZP) focal distance for the specific hologram geometry.For the specific geometry employed in this experiment, the FZP focal length is approximately the distance between the object and the recording medium.The digital images of the holograms processed with the Fresnel propagation code generated the reconstructed images shown in Fig. 2.

Conclusions
We have demonstrated that through detailed processing of the reconstructed holographic images, performed by changing the object-hologram distance in the reconstruction code, it is possible to discriminate depth in the object.Using a specially fabricated object composed of spherical markers 465 nm in diameter spread on a tilted transparent surface, the reconstruction and analysis of the hologram allowed to map the surface topography with a resolution close to 2 m, with such resolution depending on the particular NA of the exposure.
The lateral resolution of the image obtained by numerical reconstruction was assessed utilizing a wavelet image decomposition and image correlation.The best lateral resolution obtained with a high NA recording, 164 nm, represents an improvement of more than a factor two relative to previously published results.

Fig. 1 .
Fig. 1.(a) Diagram of the experimental set up.(b) Detail of the test object used.