Compact and eﬀicient injection of light into band-edge slow-modes

,


Introduction
In recent years, faster optical telecommunication and data processing have motivated research towards solutions to try to minimize the involvement of electronics in signal manipulation and to keep signals in the optical domain as long as possible.For true all-optical signal processing, one has to use optical non-linearities.Unfortunately, these non-linearities are extremely weak, thus requiring large interaction lengths or huge operational powers.Different approaches may be used to reinforce light-matter interactions including the elaboration of new materials [1] or of new structural geometries like coupled-resonator optical waveguides [2][3] or photoniccrystal (PC) microcavities [4][5].In the quest for ultimate miniaturization, slow waves obtained by introducing a periodic corrugation along the z-axis of a waveguide appears as a promising approach [6][7].Clearly, a crucial issue for integrated circuits using slow-wave waveguides is the realization of efficient light injectors between uniform z-invariant waveguides and slow-wave z-periodic waveguides.
Although it is indeed related to that of synthesizing apodized filters [8][9][10], the problem of designing efficient injectors has only been weakly addressed in the literature.Vlasov and his colleagues have experimentally investigated the impact of a fine variation of the termination of single-row defect PC waveguide [11].The injection efficiency has been shown to depend on the exact shape of the termination, but efficient slow light couplings have not been observed.A natural approach for producing this crucial optical functionality consists in using adiabatic tapers that implement a progressive light slowdown through a continuous change of the waveguide geometry.This has been studied in Ref. [12] for periodic ridge waveguides incorporating teeth in the side of the waveguide.Remarkably efficient injectors with reflectivity as small as 0.001% have been designed with this approach, but this has been achieved with taper lengths of 50 periodicities and only for rather large group velocities close to 0.1c.It can be easily shown that the length of tapers operating without any back-reflection in the taper sections (only forward-propagating Bloch modes are involved in the tapering process) rapidly increases as the group-velocity is reduced.Using a scaling factor of (c/v g ) 3 [12], it implies that such an approach would lead to taper lengths of ≈ 5000 periods for coupling light into a slow wave with v g =0.01c.
In contrast, we hereafter consider slow-wave injectors that operate as interference filters (both backward and forward Bloch modes participate in the tapering process) and that can provide efficient injection in an ultra-compact way.Typically, we report on the design of efficient injectors with characteristics lengths of a few wavelengths.In Section 2, we start with the Bloch modes of periodic layers and analytically study the group-velocity impedancemismatch problem arising at an interface between a uniform medium and a z-periodic layer stack.In particular we derive closed-form expression for the injection efficiency as a function of the group-velocity of injected light.This preliminary study is motivated by the fact that the injection problem is in essence one-dimensional and that simple intuitive analysis have not yet been presented for the back-reflection resulting at the interface between z-invariant and zperiodic media, despite its importance for our problem.Section 3 is devoted to the study of light injection at a single frequency.We show that injectors can be designed as simple Bragg mirrors that allows 100% coupling efficiencies for arbitrary small group velocities and that the injector length scales as log(c/v g ).In Section 4, we consider more realistic geometries composed of slits etched into a slab waveguide.Since radiation loss into the cladding is included into this problem, this geometry represents a test bed for even more realistic threedimensional geometries, like PC waveguides, while preserving computational requirements at a moderate level.Using a combination of fully-vectorial methods [13] and of optimisation techniques, we design efficient and wavelength-long injectors that couple light into slow waves (v g /c=0.1-0.001) with bandwidths of the order of 250 GHz at -1 dB.Section 5 summarizes the results.

Group-velocity impedance mismatch problem
We start with the scattering problem defined in Fig. 1(a).An incident plane wave in a uniform medium (refractive index n) is normally incident onto a semi-infinite periodic thin-film stack composed of lossless alternate layers with refractive indices n H and n L .Hereafter, we denote by a the periodicity constant of the thin film stack and by f (the fill factor) the fraction of material with refractive index n H .

Injection efficiency
This scattering problem can be solved by considering the modes of the two semi-infinite media at a given frequency ω.We denote by k = ω/c the modulus of the free-space wave vector.The modes in the uniform medium are the forward-and backward-propagating plane waves, denoted |P + > exp(jknz) and |P -> exp(-jknz), with a unitary Poynting vector ].The modes of the periodic medium are the Bloch modes, |B + (z)> exp(jkn eff z) and |B -(z)> exp(-jkn eff z), with |B -> and |B + > two periodic functions of the z-coordinate and with n eff the Bloch-mode effective index.|B + > and |B -> are calculated as the eigenstates of the unit-cell transfer matrix of the periodic medium and n eff as the associated eigenvalues [14].
The bi-layer stack possesses a mirror-symmetry relatively to transversal planes in the layers of refractive index n H , represented by the dashed vertical lines in Fig. 1(a) and located at planes z=z 0 +pa, with p an integer.Similar planes exist for the layers of refractive index n L .In every layer of the periodic structure, the functions |B + > and |B -> can be expanded as a superposition of two counter-propagative plane waves.We will denote by A H and B H , the modal coefficients of this decomposition in the transversal plane z=z 0 , A H referring to the forward plane wave and B H to the backward plane wave.Thus, we have The ratio u=B H /A H between the backward-and forward-modal coefficients is an important parameter which describes the stationary character of the Bloch mode.Inside the photonic gap and at the band edges where v g =0, |u|=1.Outside the photonic gap, u is real for lossless materials and using the analytical expressions obtained in [14][15], it can be further shown that 0<u<1, (2a) -1<u<0, ( for the valence and conduction bands, respectively.Similarly, the backward-propagating Bloch mode can be denoted by Note that in general, there is no relation between |B -> and |B + >, except if the periodic stack is composed of lossless materials or if it possesses a mirror-symmetry with respect to a transverse plane [15].In this case, B' H =A H and A' H =B H showing that the u-factor of |B -> is simply the inverse of that of |B + > for the bi-layer stack.After this few statements on Bloch modes, let us now go back to the scattering problem of Fig. 1(a).The total field in the uniform medium (z < 0) can be expressed as where φ = kn H fa is the phase delay associated to the propagation through the layers with a refractive index n H .The previous equation shows that the reflectance |r| 2 and the injection efficiency, equal to T=1-|r| 2 in the absence of loss, depend on Fresnel-type back-reflections through the ratio (n-n H )/(n+n H ), on the phase delay and on the u-factor of |B + >.Note that for n=n H , r is simply given by r=u exp(jφ) and the high reflectance |r| 2 close to the band-gap edges is purely due to the stationary character of |B + > (|u| ≈ 1).Using the 2x2 transfer-matrix formalism in Ref. [14], φ and u can be implicitly calculated as a function of the group-velocity v g of |B + >.The injection efficiency T=1-|r| 2 (i.e. the coupling efficiency into |B + >), in the vicinity of the band-edges of the first valence and conduction bands, is shown in Fig. 1(b), for 0.1<f<0.9.

Approximate closed-form expression for the injection efficiency
In order to get a better insight into the group-velocity impedance mismatch illustrated in Fig. 1(b), it is important to have at one's disposal simple expressions for the reflectance as a function the v g for the different optical (n, n H and n L ) and geometrical (f) parameters of the problem.According to Eq. ( 5), one needs to express u=A H /B H and φ as a function of v g .For that purpose, we use the fact that v g is the velocity of the energy propagation, v g =aP/E m , with P the power flow and with E m =1/2 ∫ Cell ε(z)|E(z)| 2 dz, a quantity related to the mode volume of B + >.P is simply equal to |A H | 2 -|B H | 2 and E m can be expressed as a function of A H and B H .We do not repeat the lengthy calculation here (a copy of a hand-written derivation could be provided on request), and we obtain for a bi-layer system with α=(1+f . Equation ( 5) is exact and provides a general relationship between the free-space wavevector k (β depends on k through φ), the group velocity v g and the stationary ratio To express φ as a function of v g , one may expand it in a power series of v g /c, φ=φ (0) +Ο(v g /c), and by retaining only the first term φ (0) , Eq. ( 5) can be solved for u(v g ) 2 , and (6a) where β VB and β CB correspond to β(φ = φ (0) ) at the valence and conduction band edges, respectively.For quarter-wave periodic stacks, f = (1+n H /n L ) -1 , a closed-form expression for the phase delay φ (0) exists [14], , the plus and minus signs holding for the conduction and valence bands.However for arbitrary f values, the calculation of φ (0) requires to solve for a transcendental equation, see Section 6.2 in Ref. [14].To retrieve full analyticity, one may use the classical coupled-wave method [16], assuming that the Bloch modes of the periodic media is described by only two counter-propagative slowly-varying zfunctions that are coupled at the band edges by the first-Fourier coefficient of the relativepermittivity modulation, ε 1 =(n H 2 -n L 2 ) f sinc(πf).Within this approach that is all the more accurate as n H -n L is small, we have where is the DC-component of the Fourier coefficients of the relative permittivity, the plus and minus signs holding for the conduction and valence bands.By substituting Eqs. ( 7) and (6) into Eq.( 4), one easily obtains a closed-form expression for the injection efficiency T=1-|r| 2 as a function of the dielectric material properties n H , n L and n and of the fill factor f in the limit of small group velocities.As noted before, for n=n H , the expressions largely simplifies and one obtains The predictions of the coupled-wave model are shown by the superimposed solid-red curves in Figs.1(b) and 1(c) for a low-and high-index contrasts, respectively.Despite the large refractive-index modulation used in Fig. 1(c), which is likely not to be accurately described by the two-first Fourier coefficients of the relative permittivity, the agreement with the transfer-matrix results is quantitative.As we checked with computational results obtained by solving the transcendental equation for the phase delay φ (0) at the band edges, the deviation in Figs.1(b) and 1(c) mainly results from the coupled-wave-method approximation used to derive Eq. (7).
For small-index contrasts, β is much smaller than α, and the injection efficiencies in Eq. ( 8) are almost identical, T VB ≈T CB .Additionally, since α≈ 2 H n + 2 L n , the injection efficiency weakly depends on f, as illustrated in Fig. 1(b).For large index contrasts, β cannot be neglected and for n≠n H , Eq. ( 4) instead of Eq. ( 8) has to used.Both situations result in a dependence of the injection efficiency with the fill factor through the phase delay φ in Eq. ( 4) or directly through the coefficients α and β.This is illustrated in Fig. 1(c), which holds for n H /n L =3.495 and for n≠n H .
Finally, note that the expressions in Eq. ( 8) largely differ from the usual ansatz [17][18], r=(v g1 -v g2 ) / (v g1 +v g2 ), where v g1 and v g2 are the group-velocities of the incident and transmitted waves.For v g2 <<v g1 , the ansatz, which leads to T=4v g2 /v g1 , completely ignores the difference of injection efficiencies at the two band edges, which is predicted by the transfermatrix computational results or by the approximate formula of Eq. ( 8).

Slow-mode injectors
The group-velocity impedance mismatch problem illustrated in Fig. 1 evidences the necessity of designing injectors for efficiently coupling light into slow modes.Indeed injectors are crucial for successful implementation or characterisation of systems relying on slow-mode field enhancements.In this Section, we show that, by engineering the interface between the uniform medium and the periodic stack, injectors with very-short length can be designed even for small group velocities.This result is established for 1D thin-film stacks and 2D periodic waveguides composed of slits in a slab waveguide.

Perfect injection in 1D thin-film stacks
We start with one-dimensional problems like in the previous section and we consider the geometry shown in Fig. 2(a), where a thin film stack (the injector to be further designed) is inserted between a uniform medium and a periodic stack supporting slow modes at the band edges.In Fig. 2(b), we sketch a situation corresponding to perfect injection.Under illumination from the uniform medium with an unit-amplitude incident normalized plane wave, no light is back reflected at plane S 1 and all the incident power is coupled into the forward-propagating slow Bloch mode of the periodic stack.This slow Bloch mode |B + >exp(jkn eff z) is defined at plane S 2 by its forward and backward-modal coefficients, A H and B H , with |A H |≈|B H |>>1 in the slow-mode regime and with |A H |²-|B H |²=1 for the sake of normalization.Perfect injection is achieved if |t|=1, t being the complex amplitude injection coefficient.
Although the following derivation can be straightforwardly obtained using time-reversal properties of lossless thin film stacks [15], we aim at a more general derivation hereafter, and we rather invoke reciprocity arguments that remain valid even for situations potentially encompassing out-of-plane scattering, as in periodic waveguides for instance.We additionally drop off any argument related to the existence of mirror-symmetry planes.Figure 2(c) depicts a reciprocal problem, where the backward-propagating Bloch mode |B ->exp(-jkn eff z) impinging from the periodic stack onto the injector transmits light into the backwardpropagating plane wave |P ->exp(-jknz) at plane S 1 , with a complex transmission coefficient t.We denote by A' H and B' H its forward and backward-modal coefficients, and since the backward-propagating Bloch mode in (c) possesses the same group velocity as the forwardpropagating Bloch mode in (b), |A' H |≈|B' H |>>1 in the slow-mode regime.Indeed solving the synthesis problem of Fig. 2(b) is identical to solving that of Fig. 2(c 2(c) evidences that the injector basically acts as a mirror for the plane waves, which reflects most of the light with a modal reflectivity coefficient r m =A' H /B' H and which transmits light with a modal transmission |t/B' H | 2 =1-|r m | 2 .Thus, designing an injector to couple light into a slow mode amounts to synthesize a mirror.In fact, the smaller the group velocity, the larger the mirror reflectance is. Figure 2(d) shows the general solution of the synthesis problem.The injector is composed of a mirror with reflectance |A' H /B' H | 2 and eventually of a phase plate, the latter being used to guaranty that the argument of r m strictly matches the argument of the stationary-ratio (A' H /B' H ) of the backward-propagating Bloch mode |B->.Thus, perfect injection into a slow Bloch mode at a single frequency ω/c=2π/λ is made possible with a mirror, and this for arbitrary small group velocities.For a mirror designed as a quarter-wave stack at the frequency ω, closed-form expressions for the modal reflection coefficient r m are available as a function of the number m of alternate layer pairs.For a mirror form with the same materials as the periodic stack, it is shown [19] that r m =(1-(n L /n H ) 2m ) / (1+(n L /n H ) 2m ), which is approximately equal to 1-2(n L /n H ) 2m for large m.By equally the latter expression with the stationary-ratio defined by Eqs.(6a) or (6b), we obtain that v g /c, where β holds for β VB or β CB .Therefore, the injector length L scales as the logarithm of c/v g and we have L=gλ log(c/v g ), (9) with g a constant parameter that depends on n, n L , n H and f.The length in Eq. ( 9) largely contrasts with those obtained with an adiabatic approach.To check this, we have solved the scattering problem shown in Fig. 2(a) with the 2x2 transfer-matrix formalism [14], for a bilayer periodic stack with n H =3.495, n L =1 and f=0.5.The injectors are simply quarter-wave Bragg mirrors composed of alternated layers with the same refractive indices n H and n L , and designed at a Bragg wavelength corresponding to the band edge of the periodic stack.Figure 3 shows the transmission T into the slow Bloch mode of the periodic stack, as a function of the frequency of the incident plane wave (actually v g on the horizontal axis).The different curves are obtained for different m values, ranging from m=1 to m=5.They have been calculated in the vicinity of the first valence band, but almost identical curves have been obtained for the conduction band.As expected, perfect injection (T=1) is achieved in all cases.Additionally we note that the group velocities corresponding to T=1 scale linearly with m (in log scale), as predicted by Eq. ( 9).The horizontal arrows delimitate the 1dB (T=0.8)bandwidth of the injector in GHz.Indeed the bandwidth vanishes as (v g ) 2 , and for very small group velocities of ≈10 -4 , it is actually very small, ≈10 -2 GHz.Therefore, injectors designed as pure mirrors cannot be used for full-optical signal processing applications, but they may find applications for single frequency applications and may be incorporated into new architectures in DBR and DFB lasers for instance.

Broadband injection in 2D periodic waveguides
So far, we have only considered thin-film-stack geometries and injectors operating at a single frequency.In planar integrated systems, the out-of-plane scattering into the claddings is an important point of concern that cannot be inferred from 1D calculations.The transverse modeprofile mismatch between the mirror evanescent Bloch mode, the guided mode of the zinvariant waveguide and the slow Bloch mode of the periodic waveguide, is expected to lower the mirror reflectance [20].Thus according to the previous analysis, this loss should prevent injection at small group velocities, since the latter requires very high reflectance.However, we believe that mirrors that incorporate tapers on both extremities [21] may allow reducing the mismatch and in turns may be used for efficient injection even at very small group velocities.We believe that by combining the mirror-design procedure in Refs.[20][21] and the 1D analysis of Section 3.1, tapered mirrors with very high injection efficiencies can be designed for a single frequency, even for small group velocities.This will be illustrated by the results discussed below.Another more specific problem in the present context is the design of injectors that achieve a bandwidth broad enough to support high data-rate telecommunication signals, while maintaining the losses at a small level.For that important problem, the 1D analysis of Section 3.1 performed at a single frequency does not help much, and this is the reason why we will rely on numerical optimisation techniques in the following example.
In order to study the feasibility of such injectors with relatively broadband and lossless couplings, we consider a semi-infinite periodic waveguide composed of a silicon (refractive index 3.5) 260-nm thick core with air claddings.Above λ = 1.5 µm, the waveguide supports a single TE guided mode.The periodic waveguide has a period a=350 nm and is composed of 185-nm large lamellar grooves etched down to the SiO in the vicinity of the band edge (k≈π/a) of the first valence and conduction bands.For broadband and lossless couplings, we have optimised injectors consisting of five slits and five ridges fully etched trough the waveguide core, the free parameters being the lengths of the ridges and grooves.An example of an optimised structure is shown in Fig. 4(a).For the optimisation we use the simplex search Nelder-Mead method.This direct method that does not use numerical or analytic gradients relies on an iterative simplex-minimization approach that progressively reduces the explored volume in the parameter hyper-space [22].The function value used for the optimisation is the weighted sum of the injector efficiency calculated for five different wavelengths in the close vicinity of a central wavelength corresponding to a targeted small group velocity of the periodic waveguide.In addition, we have imposed a firm lower bound on the efficiency, T>99% for the central wavelength.Because of the strong corrugations, one needs to solve the Maxwell's equations with fullyvectorial theory for the optimisation.We have used an aperiodic Fourier Modal Method, based on an artificial periodization in the transverse direction with perfectly-matched layers at the boundary of the supercell [13].Modal techniques are particularly efficient for performing such optimisations because the integration along the z-direction is analytical.Once the eigenmodes of the two-layer system (waveguide and groove) are calculated for the five wavelengths, the optimisation just consists in searching the injector geometry by recursively computing the scattering matrices associated to various ridge and groove lengths.For the 2D injector-design problem (invariant along the slit y-axis) investigated in this work, very high accuracy (relative error below 0.1%) is achieved for the transmission, see details in Ref. [13].
As initial guesses for the optimisation, we have considered various Bragg mirrors with different groove and ridge lengths and different target group velocities.The optimisation has revealed that many different injector geometries can be used to inject light efficiently and that the most difficult criteria to fulfil is the broadband Although the parameter hyperspace is likely not to be fully explored by the optimisation procedure, we believe that the set of solutions we obtained by repeating the optimisation with various initial guesses is likely to provide a good picture of the possible geometries that lead to efficient injection.Figure 4(a) shows a typical example of such a solution.This geometry has been obtained for a target group velocity of 0.01c in the first valence band.The superimposed red curve represents |E| 2 as a function of the z-coordinate.The field intensity in the periodic waveguide is roughly 40 times larger than that in the z-invariant waveguide.The optimised injector parameters are given in the figure caption.We note that the five slit widths progressively increase, while the five ridge widths progressively decrease along the injector.This progressive variation is well traditional for tapered mirrors engineered for ultrahigh Q microcavities, and is understood as a progressive tranverse-mode-profile matching of the various Bloch modes involved in the tapered geometry [21].This guaranties small scattering losses, and therefore a high injection efficiency in the present context.
Figure 4(b) shows the injector performance as a function of the frequency of the incident guided mode, or equivalently as a function of the group velocity of the periodic-waveguide Bloch mode.The maximal injection efficiency T (solid black curve) is obtained for v g =0.015 (λ≈1.65 µm) and is ≈99.9%.As the wavelength deviates from this value, the performance degrades.Actually, it is limited by the back-reflection R (blue circles) that rapidly increases, while the radiation losses L=1-T-R (magenta dashed curve) remain below 10 -3 over almost the entire spectral range.The 1dB (T>0.8)bandwidth is determined to be 275Ghz, a value approximately 10 times larger than that achieved with purely periodic injectors in Fig. 3.The broader bandwidth is a net effect of the large number of degrees of freedom that we have intentionally used for the 2D injector.The latter consists in 5 pairs of ridges-slits, while only m=2 layer pairs were used for the 1D injector in Fig. 3.
Similar performances have been obtained for smaller group velocities but with smaller bandwidths.For instance, for v g =0.002c, similar computations have shown that efficient injectors with a maximum injection efficiency of 99.4% can be designed with a 20 times smaller bandwidth.We believe that group velocities in the range of 0.01 that corresponds to a slow down factor of ≈40 may represent an interesting regime for on-chip optical processing with ≈250 GHz bandwidths.Smaller group velocities are likely to offer prohibitively small bandwidths and their associated propagation loss due to various disorders induced by fabrication inaccuracies may additionally be a critical issue [23][24][25].

Conclusion
In periodic media, Bloch modes with small group velocities are interference patterns and in their simplest form are created by the superposition of a forward-and a backward-propagating mode that together form a standing or a slowly-moving mode pattern.When illuminated from a z-invariant medium, light is only weakly coupled into the slow Bloch mode.For bi-layer periodic structures, we have derived closed-form expressions for the coupling efficiencies in the vicinity of the valence and conduction bands.The expressions evidence that the impedance mismatch essentially arises from the standing-wave character of the slow Bloch mode and that the injection efficiency is proportional to the group velocity of the Bloch mode, the proportionality factor being weakly dependant on the actual geometric parameters.To overpass the impedance-mismatch problem, we have explored a new route for injecting light efficiently into slow Bloch modes.In contrast to previous works using adiabatic tapers that implement a progressive light slowdown through a continuous change of the waveguide geometry, the present injectors rely on interference effects, in a way analogue to the classical multi-film-stack approach used for AR-coating [26] or impedance matching with quarterwave transformers in the transmission line theory [27].The net benefit is compactness.For instance, we have shown that very short couplers whose length are scaling as log(c/v g ), may provide perfect injection (100% coupling efficiency) at a single frequency for arbitrary-small group velocities.For 2D geometries like periodic slab waveguides, we have shown that radiation losses into the cladding are not a critical issue.We rather found that high injection efficiency together with a broadband injection is indeed difficult to manage both together, especially in the slow light regime for v g <c/100.There is a compromise.These conclusions have been reached for Bloch modes in thin-film stacks and in periodic slab waveguides, but are expected to remain quantitatively valid for other kinds of periodic ridge waveguides.Photonic crystal waveguides, like single-row-defect waveguides, deserves a specific study because the physical nature of the light confinement is different especially in the slow light regime.We expect that this prospective study will be helpful for further investigations in the field.

Fig. 1 .
Fig. 1.Impedance mismatch problem.(a): Scattering at an interface between a uniform medium (refractive index n) and a semi-infinite bi-layer periodic stack (refractive indices n H and n L ).(b) and (c): Injection efficiency T as a function of the group-velocity of the periodic-stack Bloch mode for different fill factors (0.1<f<0.9).Colormaps and white curves are exact numerical results obtained with the 2x2 transfer-matrix method in [14], and the superimposed solid-red curves are obtained using the approximate closed-form expressions.(b): data obtained in the vicinity of the valence band edge of a weak-modulation (n H =1.5 and n L =1.4) stack for n=n H . (c): data obtained in the vicinity of the conduction band edge of a strong-modulation stack (n H =3.495 and n L =1) for n=n L .

Fig. 2 .
Fig. 2. A slow-mode injector at a single frequency is basically a mirror.(a) Definition of the injector parameters : length L , interface S 1 between the coupler and the uniform medium and interface S 2 between the coupler and the periodic stack supporting a slow Bloch mode.(b) Perfect injector at a single frequency for a plane wave incident from the uniform medium.(c) Reciprocal problem.The incident illumination is the reciprocal Bloch mode propagating towards the negative z-direction.(d) General solution of the synthesis problem : the injector is composed of a mirror and of a phase plate.

Fig. 3 .
Fig. 3. Coupling efficiency into the slow-mode of a periodic stack (n H , n L ) as a function of the group velocity (log scale) of the slow mode.Different injectors are considered.They are all composed of Bragg mirrors (n H , n L ) with an increasing number of repeated pairs, m=1, …5.The results are obtained in the vicinity of the valence band edge of the periodic stack.The horizontal arrows indicate the bandwidths in GHz of the different injectors for T=0.8 (-1dB).

Fig. 4 .
Fig.4.Broadband injection from a planar waveguide to a periodic waveguide near the valenceband edge (λ=1.65 µm).(a) Injector geometry optimized for coupling at v g /c≈0.01.From left to right, the injector slit-and ridge-widths are 84, 143,127, 158, 174 nm and 239, 213, 173, 166, 166 nm, respectively.The superimposed red curve represents the squared modulus of the transverse electric field at optimal coupling.(b) Performance of the injector predicted by fully vectorial computational results for the radiation loss L (dashed curve), the modal reflection R (blue circles) and the transmission T (actually 1-T is shown with a solid black curve).All quantities are displayed in a log scale.Inset: Injection efficiency T as a function of v g with (red) and without (blue) injector.The maximum injection efficiency is as large as 0.999.In the absence of injector, this efficiency is only 0.25%.