Vibration Reduction by a Partitioned Dynamic Vibration Absorber with Acoustic Black Hole Features

Vibration quality is a vital indicator for assessing the progress of modern equipment. The dynamic vibration absorber (DVA) based on the acoustic black hole (ABH) feature is a new passive control method that manipulates waves. It offers efficient energy focalization and broad-spectrum vibration suppression, making it highly promising for applications in large equipment such as aircraft, trains, and ships. Despite previous advancements in ABH-DVA development, certain challenges remain, particularly in ensuring effective coupling with host structures during control. To address these issues, this study proposes a partitioned ABH-featured dynamic vibration absorber (PABH-DVA) with partitions in the radial direction of the disc. By employing a plate as the host structure, simulations and experiments were conducted, demonstrating that the PABH-DVA outperforms the original symmetric ABH-DVA in terms of damping performance. The study also calculated and compared the coupling coefficients of the two ABH-DVAs to uncover the mechanism behind the enhanced damping. Simulation results revealed that the PABH-DVA exhibits more coupled modes, occasionally with lower coupling coefficients than the symmetric ABH-DVA. The influence of frequency ratio and modal mass was further analyzed to explain the reasons behind the PABH-DVA’s superior damping performance. Additionally, the study discussed the impact of the number of slits and their orientation. This research further explains the coupling mechanism between the ABH-DVA and the controlled structure, and provides new ideas for the further application of ABH in engineering.


Introduction
Vibration reduction is a crucial issue that must be considered for many equipment devices [1,2].As a passive damping technique, acoustic black hole (ABH) structure has a great prospect for vibration and noise control due to its wide applicable frequency range, light-weight as well as simple and flexible implementation [3].In onedimensional cases, an ABH structure is wedge-shaped, with its thickness varying according to a power-law function.When bending waves propagate to the conical tip, their phase velocity gradually decreases to zero, resulting in zero reflection, theoretically [4].In two-dimensional cases, a similar occurrence can result in the formation of a lens that can focus the wave energy at a specific location [5].By using a small amount of damping substance at the ABH region's thinnest area, the bending waves can be effectively slowed down, concentrated and finally dissipated.This process can be used to suppress structural vibration, which makes it possible for prospective engineering applications.
Recently, the concept of add-on ABH-featured dynamic vibration dampers was proposed for broadband vibration suppression [28].The working principle embraces the advantages of both dynamic vibration absorbers and waveguide absorbers [28][29][30][31][32]. Early adoption of ABH principle in a DVA structure is a 1D resonant beam damper proposed by Zhou et al. [28], followed by more sophisticated designs such as ABH-based circular and eccentric dynamic vibration absorber by Ji et al. [29,30], a planar swirl-shaped ABH absorber by Zhou et al. [31], and a spiral ABH waveguide absorber by Park et al. [32].It is worth mentioning that Ji et al. proposed the symmetric [29] and eccentric [30] dynamic vibration absorbers based on two-dimensional ABH (2D SABH-DVA and EABH-DVA) to deal with multi-directional flexural waves.These studies demonstrated that only a few modes of the symmetrical vibration absorber can be coupled with the host structure; the selective coupling mode hinders the vibration suppression ability of the device, a problem which can be tackled to some extent by an eccentric design.In Ref. [30], the coupling coefficient is defined to evaluate the coupling effect between the host structure and add-on structure.However, the above studies are only limited to discussing the influence of modal shape on the coupling effect.Effects of other factors involved in the coupling such as modal vector, frequency ratio, mass matrix and installation angle, remain unknown.
To tackle the aforementioned problem, a new partitioned ABH-based dynamic vibration absorber (abbreviated as PABH-DVA) is proposed as an auxiliary add-on device for the vibration reduction of a vibrating structure under control.The proposed configuration retains the basic ABH profile with partitions along the radial direction of the disc, thus preserving the energy focalization characteristics at each cut segment.Both simulation and experimental results show that, breaking its structural symmetry, the proposed PABH-DVA not only improves the coupling with the host structure, but also increases the modal density of the add-on ABH structure owing to the cutting slits to enhance the chance of coupling with the vibration modes of the host structure, so as to improve the vibration suppression performance.The slot position of the add-on ABH structure does not need particular optimization, while the traditional passive DVA damper often needs meticulous adjustment to achieve good control results.To revealing the damping mechanism by the PABH-DVA, the influence of the frequency ratio between a mode of the DVA and that of the host structure is considered.Mathematical expressions of the resonance frequencies and the modal amplitude at the two resonance peaks of the coupled system are derived.Numerical examples are conducted for typical values of the frequency ratio and coupling coefficient.To consider the influence of mass ratio, modal participation factor and effective modal mass, which are closed related to the coupling coefficient, are introduced.The effective modal mass proportion and the accumulative modal mass proportion of the PABH-DVA are calculated and compared with those of the SABH-DVA.The influence of the number of slits and the installation angle is also investigated.Both the simulation results and experimental results show that the PABH-DVA outperforms the SABH-DVA in terms of vibration suppression performance.
A partitioned ABH-based dynamic vibration absorber (PABH-DVA) is proposed in this paper to address the problem of selective coupling encountered in traditional ABH-DVA for vibration reduction.To analyze the vibration suppression mechanism of the PABH-DVA and clarify the mass effect in coupling, the frequency ratio is defined.The study also investigates the influence of the number of slits and the installation angle.The findings demonstrate that achieving a large coupling coefficient and an appropriate frequency ratio are crucial prerequisites for achieving effective vibration suppression.
The paper is organized as follows: Section 1 provides an introduction to the study's focus.Section 2 presents the geometry, vibration damping performance, and coupling analysis of the PABH-DVA.In Section 3, the mechanism behind the enhanced damping effect is discussed.Section 4 examines the influencing factors, including the number of slits and the installation angle.Experimental results are presented in Section 5, and finally, Section 6 summarizes the conclusions.The research flowchart of this article is shown in Figure 1.

Geometry of the PABH-DVA
The symmetrical configuration of the SABH-DVA is shown in Figure 2. It contains three parts: A uniform central plateau with a constant thickness h 0 (from 0 to r 1 ), an annular domain with a varying thickness (from r 1 to r 2 ) and an annular platform with uniform thickness h 1 (from r 2 to r 3 ).The thickness variation along the radial direction is as follows: where ε is the multiplier of the ABH curve, which determined by radius and maximum thickness, m is the power index of the ABH curve.
An annular damping layer of a constant thickness h d is bonded along its outer edge of the ABH-featured disk, as shown in Figure 2(b).The above disc is radially partitioned through cutting a seam width d in the area except the center of ABH disk by mechanical cutting method.Since there are many partition schemes to choose, a DVA partitioned into three parts is taken as an example, as shown in Figure 2(c), abbreviated as P3ABH-DVA.
The P3ABH-DVA is attached to a host structure, exemplified by a rectangular plate, using either glue or a bolt, (1)   .As an add-on device, rather than an embedded indentation into the host structure, its inclusion does not jeopardize the stiffness or the mechanical strength of the host structure.For numerical analyses, aluminum serves as the primary material for the PABH-DVA and the host structure, while butyl rubber serves as the damping substance.The dimension of the host structure measures 300 mm × 240 mm × 6 mm in the present case, the total mass of the P3ABH-DVA is set to 0.0521 kg, which is 4.45% of the host plate.The P3ABH-DVA is installed at a position 30 mm away from both sides of the plate, and this point is used as the origin of the coordinate system, as shown in Figure 3(a).The plate is excited by a transverse force of 1 N in amplitude at a point with a coordinate of (220, 140) mm.It should be mentioned that the position of the installation is not optimized in this case.Because most of the modes of a plate with free boundaries have considerable vibration amplitude in the corners, it was decided to install close to one of the plate's corners, so as to expect that the PABH-DVA can still couple with as many modes as possible within the given and broad frequency range.As shown in Ref. [30], the large vibration amplitude in the three degrees of freedom (one translational and two rotational) of the installation point warrants good coupling between the ABH-DVA and the host structure.The material and geometrical parameters of the host structure and those of the ABH-DVAs are listed in Tables 1 and 2, respectively.
Numerical simulations are performed using Abaqus to gain insights into the dynamics of the host structure, addon devices, and their synthetic systems.The host structure is represented using shell elements (S8R), while the addon DVA is modeled using 3D solid elements (C3D20R), as depicted in Figure 3(b).Refined grids are utilized in the margins of the P3ABH-DVA and SABH-DVA to ensure the accuracy of the numerical simulations.The mesh size is chosen to ensure a minimum of ten elements per wavelength.For modal analysis, both the host structure and the synthetic systems are subjected to free boundary conditions.A rigid connection is applied over the installation interface, which refers to the central plateau of the add-on DVAs.
The driving point mobility v dp and mean velocity of the plate v n , normalized based on exciting force, with a ref- erence value of 1 m•s −1 •N −1 , are defined to evaluate the vibration level of the plate, the mean velocity v n can be defined as: where v n is the normal velocity of the plate and S is the whole vibrating surface.Using the logarithmic value of the normalized speed according to the excitation force as the vibration level.

Vibration Damping Performance of the P3ABH-DVA
Figure 4(a) illustrates the driving point mobility of the uniform plate, along with the synthetic system incorporating both the P3ABH-DVA and SABH-DVA of equal size.It is evident that the addition of DVAs effectively suppresses structural vibrations in the system.Furthermore, the P3ABH-DVA exhibits a better performance than the SABH-DVA in terms of reducing specific peaks, particularly at frequencies of 218 Hz, 640 Hz, 967 Hz, and 1962 Hz.At these frequencies, attenuation levels of 10 dB, 19 dB, 15 dB, and 25 dB are achieved, respectively.However, for most peaks, there is not a significant difference between the two DVAs.The mean velocity of the host plate follows a similar trend, as depicted in Figure 4(b).In other words, the P3ABH-DVA provides additional vibration reduction at certain frequencies that can also be addressed by the SABH-DVA.
Further inspection of the response curve suggests two main vibration suppression phenomena: The dynamic interaction (conventional DVA effect) evidenced by the typical peak splitting phenomenon; and damping enhancement (energy dissipation) as reflected by the reduction in some resonance peaks without splitting, in agreement with previous observations made in SABH-DVA [29] and EABH-DVA cases [30].
Although both the previously proposed EABH-DVA and PABH-DVA can improve the selective coupling of the SABH-DVA, differences exist between them in terms of physical mechanism.The former changes the modal distribution without changing the effective modal mass and (2)  modal density, while the latter increases the modal density (to be confirmed in Section 3.1) by sacrificing a small amount of effective modal mass (to be confirmed in Section 3.2) to achieve the above purpose.But in aggregate, the occurrence of the aforementioned phenomena would both rely on an effective dynamic coupling between the host structure and the add-on ABH-DVA, which calls for further analyses in the later section.

Coupling Analyses through Coupling Coefficients
The coupling coefficients between the modes of the addon DVA and those of the host structure have been used to evaluate the coupling characteristics of the two coupled sub-structures [30].For completeness and convenience of later usage, the formulation of the coupling coefficient is briefly recalled.The dynamic equation of each sub-discretized system has the following form: where M A , C A and K A are the mass, damping and stiffness matrices for the add-on DVA, M s , C s and K s are (3) those for the host structure; w A and w s are their corresponding nodal displacements; F is the excitation force acting on the host structure.
Using the modal superposition method and normalizing according to the modal mass, Eqs. ( 3) and ( 4) can be written as the following form in the principal coordinates as: where I is a unit matrix, q A is the modal coordinate of the add-on DVA; [2ω A ζ A ] is a diagonal matrix with its ith diagonal element equal to 2ω Ai ζ A , where ω Ai and ζ A are the natural frequency and the modal damping ratio of the add-on DVA respectively.[ω 2  A ] is also a diagonal matrix and its non-zero diagonal elements are ω 2 Ai .Replacing sub-index A by s, all quantities apply to the host structure.
According to the previous definition [30], the displacement of the add-on DVA attached to the nth node of the host structure can be written as: where Φ A is the modal shape matrix of the add-on DVA, {1} , R y , R x are N A ×1 vectors, and their components are all equal to 1, y coordinate and x coordinate of the corresponding node, respectively.w sn , θ nx and θ ny are the out-of-plane displacement and the two rotational angles, respectively.
Substituting Eq. ( 7) into Eq.( 3) and utilizing Eqs. ( 5) and ( 6) give: Obviously, the second term in the aforementioned equations determines the coupling between the add-on DVA and the host structure.According to Eqs. ( 8), (9), the coupling coefficient between the ith mode of the add-on DVA and the jth mode of the host structure, denoted by α ij , can be defined as: (5) The coupling coefficients are calculated according to Eq. (10) and Eq.(11), and the results are presented in Figure 5.It can be observed that the P3ABH-DVA exhibits coupling with the host structure for the first 6 modes, whereas the SABH-DVA only shows coupling for the 1st, 2nd, and 5th modes.Additionally, the coupling frequency band of the P3ABH-DVA is broader than that of the SABH-DVA, spanning approximately 250 Hz to 1200 Hz.This aligns with the more effective frequency band of (10) α (1) the P3ABH-DVA demonstrated in Figure 4.It is worth noting that the modal participation factor discussed in Section 3.2 provides a similar representation, but the coupling coefficient incorporates the influence of the installation position as an additional factor.More coupled modes in the new PABH-DVA means that it gives a greater number of dynamic dampers to the host structure.However, although there are more coupled modes in the PABH-DVA than in the original SABH-DVA, most of the coupling coefficients in the PABH-DVA are smaller than those in the SABH-DVA.Moreover, the damping effect of a dynamic damper is not only determined by the coupling coefficients, but also by its frequency ratio and mass ratio.Hence, further analysis of the mechanism for enhancing damping effect by the PABH-DVA is necessary.

Frequency Ratio
According to classical vibration theory, the frequency ratio between the mode of the DVA and the mode of the host structure plays a crucial role in achieving a good damping effect.When the damping effect is achieved, the original resonance peak of the structure splits into two, with the heights of these peaks depending on the damping ratio of the DVA.With a sufficiently high damping ratio, the two split peaks are effectively suppressed, resulting in excellent damping performance.The ideal frequency ratio is typically around 1. Deviations from this ratio lead to a deterioration in the damping effect.In the case of the ABH-DVA, each coupled mode acts as a DVA.Therefore, it becomes important to investigate the influence of the frequency ratio between the coupled mode of the ABH-DVA and that of the host structure on the damping effect.
Without loss of generality, the interaction between the ith mode in the add-on DVA and the jth mode in the host structure is considered by neglecting all the other modes.According to Eqs. ( 8) and ( 9), the equations of dynamic of the 2-DOF system become: In the frequency domain, the equations can be expressed as: (12)  where F mj is the amplitude of the modal force and qAi and qsj are the complex amplitudes of modal displacement of the ABH-DVA and the host structure, respectively.Solution of Eq. ( 13) gives: where When the coupling coefficient α ij = 0 , the ith mode in the DVA is not coupled with jth structural mode.The amplitude of the structural mode at ω = ω sj , at which the real part of the determinant Δ is zero, is usually defined as the resonance amplitude.When the resonance amplitude is normalized with respect to the static displacement δ st , it can be expressed in the following form: where δ st = F mj /ω 2 sj .When α ij = 0 , the complex amplitude of the host struc- ture is: where β ij = ω Ai /ω sj is the frequency ratio and � = ω/ω sj is the normalized frequency.
The denominator in Eq. ( 17) is the dimensionless form of the determinant Δ.For convenience, the frequencies at which the real part of the denominator becomes zero are defined as the resonance frequencies.That is, the resonance frequencies satisfy: The two roots of Eq. ( 18) is denoted by 1 and 2 ( � 1 > � 2 ), respectively.Obviously, � k (k = 1, 2) are functions of the frequency ratio β ij .The relationship between � k (k = 1, 2) and β ij with α ij as the parameter is shown in Figure 6(a).It is obvious that one of the two normalized resonance frequencies approaches 1 and the other approaches β ij as β ij deviates significantly from 1.That is, one resonance frequency approaches ω sj and the other approaches ω Ai .Additionally, it is worth not- ing that a larger coupling coefficient allows for a greater (14) tolerance in the coupling frequency.This means that even with slight deviations from the ideal frequency ratio, the damping effect can still be maintained effectively when the coupling coefficient is higher.The larger the coupling coefficient, the more robust the system becomes against variations in the coupling frequency.It indicates that the dynamic interaction between the two modes weakens as The normalized modal amplitudes of the structure at these two resonance frequencies are: Obviously, the normalized modal amplitudes q(k) sj δ st (k = 1, 2) are functions of β ij .As an example, the damping ratios of ABH-DVA modes and structural modes are set to ζ A = 0.1 and ζ s = 0.001 , respectively.Variation of the normalized modal amplitudes as functions of β ij with the coupling coefficient α ij as the param- eter is shown in Figure 6(b).
According to Figure 6(b), the normalized amplitude of the peak with lower frequency 2 increases with frequency ratio β ij , and that of the peak with higher fre- quency degree 1 increases with β ij .To achieve the best performance, the optimal β ij should be located at the crossover point of the two amplitude curves.For α = 0.1, the optimal value is about β ij = 0.99 , and for α = 0.2, the optimal value is about β ij = 0.96 .When the fre- quency ratio deviates from the optimal value by 10%, the amplitude at one of the peaks becomes almost twice.In order to achieve good damping performance, frequency matching with β ij in the vicinity of the optimal value is very important.Indeed, the density of coupled modes of the ABH-DVA in the frequency domain plays a crucial role in enhancing damping performance.A higher modal density indicates a greater number of modes available for coupling between the DVA and the host structure.This increased modal density leads to a higher probability of modal coupling, facilitating efficient energy transfer and vibration suppression between the two systems.Consequently, a higher modal density contributes to improved damping performance by enabling a broader range of modes to participate in the vibration reduction process.
In order to verify the above statement, the modal frequencies of the P3ABH-DVA, SABH-DVA of equal size and the host plate in Figure 3 are calculated.The frequency range up to 2000 Hz is illustrated in Figure 7.It can be seen that SABH-DVA has many symmetric (19) q(k) modes, but few modes can be coupled with the host structure, and the overall mode density and coupled mode density of P3ABH-DVA are significantly higher than that of SABH-DVA, especially during 200−400 Hz and 1000−1200 Hz intervals, which also explains that the response of the system with P3ABH-DVA in Figure 4 is lower than that of the system with SABH-DVA in the above frequency band.The damping increase brought up by DVAs to the system can also be seen from the response curve (Figure 4).Extracting the typical peaks within 3500 Hz of the three response curves, keeping the same number of peaks of the three curves, the damping of each peak is obtained by simulation and shown in Figure 8.It is obvious that the system with P3ABH-DVA has higher damping ratio and lower response than that with SABH-DVA, as a result of the increase in the coupling caused by the expansion of frequency ratio.In fact, the change of effective mass distribution is also an indispensable account, which will be explained in Section 3.2.

Mass Effect of DVAs
The mass ratio is another influencing factor of vibration reduction effect.However, it is difficult to understand the mass effect directly from Eq. ( 12) because it has been normalized with respect to modal mass.Instead, the effective modal mass is considered [33].It is obvious that the two substructures are coupled through the reacting forces related to the three degrees of freedom (DOFs) at the installation point, which are w sn , θ nx and θ ny , respec- tively.The modal mass participation factors of the ith ABH-DVA mode related to the three interface DOFs are α (k) i1 (k = 1, 2, 3), respectively.The effective modal masses are the square of the modal mass participation factors [33]: The above expression indicates that the coupling coefficient has included the information of effective modal mass of the ABH-DVA.
The effective modal mass proportion (EMMP) of the ith mode is defined as: and the cumulative effective modal mass proportion (CEMMP) below a given frequency f is defined as: As a numerical example, the EMMPs, R  (20)   It is obvious that although the EMMP of P3ABH-DVA is smaller than that of the SABH-DVA, but its CEMMP is not small, and in some frequency ranges, slightly larger than the SABH-DVA.It means that the effective mass is hardly reduced due to partition the SABH-DVA into three parts in the P3ABH-DVA.On the other hand, more coupled modes in a given frequency range lead to higher modal density and easier frequency matching between the modes of the P3ABH-DVA and those of SABH-DVA.
Based on the above analysis, it is clear that cutting the ABH-DVA into some parts can increase the density of coupled modes and improve the damping effect on more modes of the host structure.Although the 1st, 2nd and 5th modes of the SABH-DVA have very high effective modal mass proportion and they are strongly coupled with most of the modes of the host structure as shown in Figure 5(a), they are only effective for the modes of the host structure below 500 Hz due to the influence frequency ratio.The next strongly coupled modes of the SABH-DVA are the 16th, 17th and 18th modes and the frequency gap is 869.62 Hz, from 304.28 Hz of the 5th to 1173.9 Hz of the 16th mode.The frequency gap for the P3ABH-DVA is 688.14 Hz, from 320.76 Hz of the 7th mode to 1008.9 Hz of the 17th mode, as shown in Figure 5(b).The 11th, 12th and 13th modes of P3ABH-DVA are also weakly coupled.Therefore, the mode of the host structure at 1015.9 Hz can be effectively reduced by the P3ABH-DVA.

Other Influencing Factors
Since the analysis in the above section indicates that the damping performance can be improved by partitioning the ABH-DVA into several parts, it is necessary to discuss the influence of the number of slits and the orientation of the partitions.

Influence of the Number of Slits
As an example, PABH-DVAs of the same size with four and five slits are considered in this section.The partition schemes in these two PABH-DVAs are shown in Figure 10, and the host structure is the same as that in Section 2.1, maintaining the same installation position, external excitation, material parameters, etc.The driving point mobility and mean velocity of synthesized system with different add-on DVAs within 2000 Hz are shown in Figure 11.It can be seen that the DVA with different number of slits can produce better vibration suppression effect than SABH-DVA, and the specific frequency of each type of DVA is different.This can be explained from the mechanism of vibration reduction.
Without loss of generality, the function of the ith mode of the add-on structure in a polar coordinate can be expressed as φ Ai (r, θ) .The factor α (k) i1 ( k = 1, 2, 3 ) in Eq. ( 11) can be converted into the following form in the continuous space as [33]: In the symmetrical ABH-DVA, r and θ in φ Ai (r, θ) are separable and the mode with a radial order m and a circumferential order n is denoted by RmCn, whose modal function writes: When the axisymmetry of the device is destroyed in the PABH-DVA, φ Ai (r, θ ) becomes more complex and the r and θ are not separable anymore.Therefore, theoretically α (1)  i1 , α (2)  i1 and α (3)  i1 in Eq. ( 23) do not become zero for any mode number i.
This new configuration preserves the ABH profile in the radial direction alongside a continuous variation along circumferential direction and breaks the axisymmetry of the original DVA design at the same time.The targeted outcome is a compact and light-weight device with enriched ABH features and enhanced coupling with a host structure onto which it is surface-mounted to achieve broadband vibration suppressions without a complex tuning procedure.

Influence of Installation Angle
In order to investigate the influence of installation angle, a 65° partition from the P3ABH-DVA is considered.Two cases (I and II), 180° different, are shown in Figure 12.The mobility of the two cases are shown in Figure 13.
It is obvious from Figure 13 that Case II has a better vibration suppression effect than Case I, especially at 267 Hz, 653 Hz and 1015 Hz in the lower frequency range, while the damping effect of the two cases being almost the same at higher frequency range.The reason is that the coupling coefficient is different in the two cases.According to Eq. ( 14), the damping effect of ABH-DVAs depends on the coupling coefficient, which is expressed as the product of α In order to explain the observed differences of damping effect in relation to the installation angle, the corresponding coupling coefficients are considered.The only difference in Case I and Case II is that the ABH ( 23) j2 (k = 1, 2, 3) are the same for the two cases because they have the same installation position.As shown in Ref. [30], α i1 of Eq. ( 11) in an equivalent continuous system can be written as: i1 can be written as: (25)  , Similarly, there exists: The above results indicate: The damping of the first two structural modes of the host structure is considered.Their respective frequencies are 267.41Hz and 345.41 Hz, and their modal shapes are shown in Figures 14(a The three terms on the right side of Eq. (28), j2 (k = 1, 2, 3) , are calculated and their val- ues for the two cases are shown in Table 3.For the interaction between the 1st structural mode and 1st DVA mode, their coupling coefficients are α (I) 11 = 0.0593 and α (II) 11 = 0.1945 , respectively for Case I and Case II.Appar- ently, Case II has a larger coupling coefficient than Case I due to the cancellation of different terms in Eq. ( 28) and Eq. ( 29) for Case I.The first two peaks in the coupled system are ω 2 =219.09Hz and ω 1 =276.21Hz.This can also explain that the dynamic vibration absorption effect of Case II is much better than Case I. Since β 11 = 0.856 is significantly smaller than its optimal value (more than 10%), there exist � 2 = 0.819 ≈ β 11 and 1 = 1.045 ≈ 1 , which is in agreement with the result in Figure 6(a).Figure 13 shows that the peak at ω 1 =267.86Hz is less significantly reduced, which also agrees with the result in Figure 6(b).Since α (II)  11 > α (I) 11 , the peak at ω 1 of Case II is smaller than that of Case I, which is also consistent with Figure 6(b).This also indicates that the installation angle can also influence the damping performance.For the modes at 267 Hz, 653 Hz and 1015 Hz shown ( For the interaction between the 2nd structural mode and 2nd DVA mode, there exist α (I) 22 = −0.0262and α (II) 22 = 0.0262 .Since the coupling coefficient α ij appears in the determinant Δ (Eq.( 15)) in the squared form, its sign does affect the damping performance.Since β 22 = 0.927 and α 22 = 0.0262 are both rela- tively small, ω 1 =347.53Hz and 1 = 1.006 ≈ 1 .The small value of α 22 = 0.0262 indicates a weak inter- action between the host structure and the DVA.The weak interaction leads to the result that the peak at ω 1 =347.53Hz is only slightly reduced and the other peak is not clearly visible in the frequency response curve in Figure 13.

Experimental Verifications
Experiments were carried out to verify the above broadband vibration suppression phenomenon.The DVAs and the host plate utilized for comparison were produced by aluminum using computer numerical control (CNC) milling.The add-on DVAs were attached onto the host structure using a standard 5 mm screw, as shown in Figure 15, the size and damping substance were identical to those of the simulations mentioned above.
Figure 16 shows the experimental setup.An electromagnetic shaker (B&K 4809), driven by a power amplifier (B&K 2718), was used to generate a periodic chirp force from 10 Hz to 3500 Hz to excite the plate at the position in the above simulation.The free boundary condition in the experiment was achieved by suspending the plate to a rigid frame using two elastic strings.A Polytec ™ Laser Scanning Vibrometer (PSV 500) was used to perform the response measurement.
The driving point mobility and the mean velocity of the host structure and synthetic systems were measured up to 3500 Hz and the results are shown in Figure 17.The response curves of the two DVAs basically reflects the two main vibration suppression mechanisms of conventional DVA effect (about 260 Hz) and energy dissipation (about 600 Hz).Besides, it can be observed that the P3ABH-DVA generally leads to the best control performance, in terms of both resonant peak attenuation and broadband vibration reduction, such as 259 Hz, 1020 Hz and 2204 Hz, there are 21 dB, 8 dB and 7 dB attenuation respectively.As demonstrated in numerical simulations, this is owing to the partitioned DVA changes the effective mass distribution by sacrificing a small amount of effective modal mass, brings more modal frequencies and increases the coupling opportunities with the host plate.The coupling coefficients in some specific frequency bands is also increases, collectively contributes to a broadband vibration reduction of the system.Although there are some inevitable errors in the experiment, the overall trend is consistent with the above simulation.
In addition, the partitioned DVA still maintains some basic characteristics of the symmetrical DVA, it cannot guarantee that all frequency bands can achieve excellent vibration reduction effect.This has also been confirmed in the simulation.If multi-band vibration reduction is

Conclusions
This paper proposes a partitioned ABH-based dynamic vibration absorber (abbreviated as PABH-DVA), as an auxiliary add-on device for the vibration reduction in a controlled structure.The proposed configuration retains the basic ABH profile, thus preserving the energy focalization ability in each cut segment of the disc.The main conclusions are drawn as follows.
(1) The new PABH-DVA yields better damping performing than the original symmetric ABH-DVA.
The underlying mechanism of this phenomenon roots in the frequency relationship between the two structures (frequency ratio) and the modal participation factor (mass ratio).(2) The proposed PABH-DVA improves the coupling characteristics with the host structure by changing the frequency ratio.It increases its modal density by cutting slits to improve the chance of coupling with the vibration modes of the host structure, so as to improve the vibration suppression performance.The slit position of the add-on DVA does not show much influence thus needing no particular optimization, which is an advantage of the PABH-DVA.(3) The proposed PABH-DVA improves the coupling characteristics with the host structure by enriching the mass ratio.Although each of the coupled modes of PABH-DVA has a smaller effective modal mass proportion than SABH-DVA, the number of modes that PABH-DVA interacts with the host structure is greater than that of SABH-DVA.The total cumulative effective modal mass proportion is not small and is slightly larger than SABH-DVA in some frequency ranges.Theoretically, increasing the number of slits is beneficial to frequency matching, but it also sacrifices the modal effective mass.Therefore, although the number or position of slots does not need to be precisely designed, a certain tradeoff needs to be made in light of the characteristics of the structure to be controlled.(4) Other influencing factors, the installation angles have also been considered.Different installation

Figure 4
Figure 4 Driving point mobility of the host plate with different add-on DVAs

Figure 5
Figure 5 Modal coupling coefficients between the two types of add-on DVAs and the host structure within 3500 Hz: (a) SABH-DVA, (b) P3ABH-DVA the SABH-DVA and P3ABH-DVA in the frequency range below 1500 Hz are shown in Figures 9(a) and (c).The SABH-DVA contains 22 modes and the P3ABH-DVA has 30 modes in the frequency range below 2000 Hz.Obviously, each coupled mode of the P3ABH-DVA has smaller EMMP than that of the SABH-DVA, but the P3ABH-DVA has a larger number

Figure 7 Figure 8
Figure 7 Modal frequency distribution of three structures within 2000 Hz

Figure 12 Figure 13
Figure 12 Different installation angle schemes of DVA

Figure 14
Figure 14 Modal shape of the two different installation angle cases: (a) The 1st mode of host plate, (b) The 2nd mode of host plate, (c) The 1st mode of 65°-partition DVA in case I, (d) The 1st mode of 65°-partition DVA in case II, (e) The 2nd mode of 65°-partition DVA in case I, (f) The 2nd mode of 65°-partition DVA in case II

Figure 16 Figure 17
Figure 16 Experimental test set-up

Influencing Factor Coupling Coefficient Frequency Ratio Mass Effect Deficiency Intrinsic Property Number of Silts Installation Angle Interaction Mechanism Figure 1
Flow diagram of the research

Table 1
Material parameters

Table 2
Structural geometric parameters