On double-diffusive convection and cross diffusion effects on a horizontal wavy surface in a porous medium

An analysis of double diffusive convection induced by a uniformly heated and salted horizontal wavy surface in a porous medium is presented. The wavy surface is first transformed into a smooth surface via a suitable coordinate transformation and the transformed nonsimilar coupled nonlinear parabolic equations are solved using the Keller box method. The local and average Nusselt and Sherwood numbers are given as functions of the streamwise coordinate and the effects of various physical parameters are discussed in detail. The effects of the Lewis number, buoyancy ratio, and wavy geometry on the dynamics of the flow are studied. It was found, among other observations, that the combined effect of Dufour and Soret parameters is to reduce both heat and mass transfer. MSC:34B15, 65N30, 76M20.


Introduction
The study of double-diffusive convection has received considerable attention during the last several decades because of its occurrence in a wide range of natural and technological settings. Double-diffusive convection is an important fluid dynamic phenomenon that involves motions driven by two different density gradients diffusing at different rates (Mojtabi and Charrier-Mojtabi []). A common example of double diffusive convection is seen in oceanography, where heat and salt concentrations exist with different gradients and diffuse at differing rates. Double diffusive convection manifests in the form of "salt-fingers" (see Stern [, ]) which are observable in laboratory settings. The input of cold fresh-water from an iceberg can affect both of these variables. Double-diffusive convection has also been cited as being important in the modeling of solar ponds (Akbarzadeh and Manins []) and magma chambers (Huppert and Sparks [], Fernando and Brandt []). Doublediffusive free convection is also seen in sea-wind formations, where upward convection is also modified by Coriolis forces. This is of particular interest in oceans where the Earth's rotation plays a dominant role in many of the motions observed.
In engineering applications, double diffusive convection is commonly visualized in the formation of microstructures during the cooling of molten metals, and fluid flows around shrouded heat-dissipation fins. Typical technological motivations for the study of doublediffusive convection range from such diverse fields as the migration of moisture through http://www.boundaryvalueproblems.com/content/2012/1/88 air contained in fibrous insulations, grain storage systems, the dispersion of contaminants through water-saturated soil, crystal growth, solidification of binary mixtures, and the underground disposal of nuclear wastes. Other important applications can be found the fields of geophysical sciences and electrochemistry. A comprehensive review of the literature concerning natural convection in fluid-saturated porous media may be found in the books by Ingham  Most free convection studies mainly focus on the cases where the thermal boundary conditions allow the use of similarity transformations to reduce the governing boundary layer equations to a system of ordinary differential equations which can be handled either analytically or numerically. The existence of self-similar solutions point to the fact that, in general, the heated surface must have a plane geometry. In reality, the heated surfaces need not always be planar. Surfaces are sometimes deliberately roughened to achieve enhanced heat transport. Heat transfer devices like flat-plate solar collectors and flat-plate condensers in refrigerators possess a nonuniform surface. Further, in cavity wall insulating systems and grain storage systems, one can witness pronounced surface roughness. Yao [] and Moulic and Yao [, ] were the first to include the effects of surface nonuniformities on the free convection thermal boundary layer flow of a Newtonian fluid. Rees and Pop [, ] investigated parallel thermal boundary layers due to natural convection induced by a vertical surface with sinusoidal undulations embedded in a in porous medium. Subsequent studies by Rees and Pop [, ] considered the effect of surface waves on the convection due to either horizontal or vertical wavy surfaces embedded in a porous medium. In the case of horizontal wavy surface, Rees and Pop [] found that the amplitude of the surface waves must be within an O(Ra -/ ) range in order to balance direct and indirect buoyancy forces. They showed that for wall amplitudes greater than about .Ra -/ , the flow separates with one or more regions of reverse flow. Rees and Pop [] obtained similarity solutions for the case of longitudinal surfaces waves with (i) a prescribed power-law temperature is set on the surface, and (ii) a prescribed power-law heat flux.
Cheng [-], in a series of papers investigated free convection due to vertical/inclined wavy surfaces in porous media. Cheng [] studied natural convection, heat and mass transfer near a vertical wavy surface with constant wall temperature and concentration in a porous medium. He showed that the average Nusselt and Sherwood numbers for a sinusoidal wavy surface are constantly smaller than the corresponding results for a flat plate. This work was generalized in Cheng [] to a non-Darcy model for natural convection heat and mass transfer from a vertical wavy surface in a porous media. Cheng [] considered a non-Newtonian power law liquid to study combined heat and mass transfer in free convection flow due to a vertical wavy surface in a porous medium with thermal and mass stratifications. It was found that an increase in the power-law index, the thermal stratification parameter, or the concentration stratification parameter leads to a smaller fluctuation of the local Nusselt and Sherwood numbers with the streamwise coordinate. Double diffusive natural convection along an inclined wavy surface in a porous medium was investigated by Cheng [] and showed that the inclination angle enhanced the total heat and mass transfer rates.
Pop and Na [] studied natural convection due to a frustum of a wavy cone in a porous medium and discussed the effects of geometry of a wavy cone on the heat transfer. Cheng [] studied the natural convection heat and mass transfer near a wavy cone with constant http://www.boundaryvalueproblems.com/content/2012/1/88 wall temperature and concentration in a porous medium. Using a cubic spline method of solution, he showed that the buoyancy ratio leads to higher heat and mass transports while the diffusivity ratio (Lewis number) reduces heat while increasing mass transports. Cheng [] obtained nonsimilar solutions for double diffusive convection near a frustum of a wavy cone in porous media and showed that the average Nusselt and Sherwood numbers for the wavy cone are smaller than the corresponding smooth cone. Double-diffusive natural convection along a vertical truncated wavy cone in non-Newtonian fluid saturated porous media with thermal and mass stratification has been investigated by Cheng [].
In this study, he showed that the power-law index leads to smaller fluctuations in the local Nusselt and Sherwood numbers and increasing the thermal and concentration stratification parameters reduce the heat and mass transfer rates.
An energy flux is often generated by both temperature and solute gradients leading to In this paper, we extend the work by Rees and Pop [] to include the solute diffusion in natural convection induced by a horizontal wavy surface profile in a porous medium. The wall temperature and concentrations are assumed to be constants and the amplitude of the wave is assumed to be small enough so as not to engender any regions of reverse flow (these issues are dealt in detail by Rees and Pop []). Assuming the Rayleigh number Ra to be very large, the boundary layer approximation is invoked leading to a set of nonsimilar parabolic partial differential equations whose solution is obtained using the Keller box

Mathematical formulation
Consider the problem of double-diffusive convection in a fluid around a horizontal surface with transverse sinusoidal undulations embedded in a porous medium. Figure  shows the schematic sketch of the problem. The wavy surface profile is described by where a * is the amplitude of the surface wave, l is the characteristic length of the wave, and ϕ is the phase of the wave. The temperature and the solute concentrations at the surface are assumed to be constants T w and C w which are greater than the ambient values T ∞ and C ∞ , respectively. We also assume a steady convective flow with the properties of the fluid and porous medium to be constant except for the buoyancy term. Following the Boussinesq approximation, the governing continuity, momentum, heat, and solute concentration equations can be written in the form Here, g is the acceleration due to gravity, K is permeability of the porous medium, ν is the kinematic viscosity, β is the coefficient of thermal expansion, β * is the coefficient of solutal expansion, κ is the thermal diffusivity, D is the solutal diffusivity, k  and k  are the coefficients of cross diffusion. We now use the following nondimensional variables: () http://www.boundaryvalueproblems.com/content/2012/1/88 The governing equations ()-() take the form: The dimensionless parameters appearing in the above set of equations are the Rayleigh number Ra, the buoyancy ratio N , Dufour number D f , the Soret number Sr, and the Lewis number Le defined as follows: The boundary conditions in () take the following nondimensional form: Introducing the stream function ψ(X, Y ), such that the continuity equation () is satisfied automatically and Eqs. ()-() can be written in the following form: with the boundary conditions () http://www.boundaryvalueproblems.com/content/2012/1/88 The effect of the wavy surface and the usual boundary layer scalings are incorporated into the governing equations ()-() using the transformations, along with the substitutions Equations () transform the wavy surface to a smooth surface in the physical configuration. Substituting () and () into Eqs. ()-() and letting Ra → ∞, we obtain the following boundary layer equations: subject to the boundary conditions The associated local Nusselt and Sherwood numbers The mean Nusselt and Sherwood numbers from the leading edge to the free stream position x are given by

Solution procedure
The nonsimilar parabolic partial differential equations that govern the dynamics of the fluid flow were solved using the Keller The boundary conditions take the form In the discretization and formation of finite difference equations, the computational domain (ξ -η plane) is divided into a finite number of mesh points that form the corners of the rectangle shown in Figure (a). The net points are defined as where h i and k j are respectively the spacings in the ξ and η directions. The choice of net spacings is done manually in the present paper but can be generated automatically. A typical mesh rectangle over which Eqs. ()-() are to be approximated is indicated in Figure (b). The equations are centered around one of the points marked by "×. " A finer grid that points toward the surface (η = ) and a coarser grid that points away from the surface (η → η ∞ ) are usually chosen for nonsimilar boundary layer flows, however, here we use uniform grid points in both directions. We fix η ∞ =  which is well outside the plane boundary layer surface. Since the boundary-layer equations have been formulated as a first-order system, all derivatives can be approximated by simple centered differences and two-point averages, using only values at the corners of the box. This type of differencing is as compact as possible and is, as we shall see, one of the most attractive features of the Box scheme. We use the notation [·] i j for any quantity represented midway between net points and this notion should not be confused with the tensorial one. Then, for any net quantity w we use the following finite difference approximations: () Using the box-scheme approximations (), Eqs. ()-() yield the following nonlinear finite difference equations: Further manipulation yields the following equations: . The boundary conditions take the form The difference equations ()-() are imposed at each grid points η j , j = , , . . . , J giving rise to J algebraic equations. The boundary conditions () along with the difference equations ()-() comprises a system of J +  equations for as many variables. There are several methods for solving these J +  equations. In this study, we employ Newton's method which is easy to implement. We use Newton's method to linearize the nonlinear finite difference equations ()-() which possesses quadratic nonlinearity. Assuming that the nth iterates of the variables are known the iterate (n + )th iterates are given by (   ) http://www.boundaryvalueproblems.com/content/2012/1/88 We further define the following variables for brevity.
Substituting Eqs. ()-() into Eqs. ()-() and retaining only linear terms in δ, the linearized finite difference equations can be written as: From the boundary conditions, we get the following difference equations: The linearized difference system of Eqs. ()-() can be solved by any standard method like elimination or iterative methods. Since the linearized system has a block tridiagonal structure, we employ a block-elimination method. The block tridiagonal system in its matrix form is written as follows: We first factorize the coefficient matrix as follows: .
where I is an identity matrix of order . The procedure involves two sweeps, i.e., a forward sweep and a backward sweep. In the forward sweep, the unknowns j , j , and the intermediate variables ∇ j are determined and in the backward sweep the required solution j is determined in terms of j and ∇ j .

Forward sweep:
Initial matrices: Using the above, the successive matrices are obtained using the following formulae:

Backward sweep:
The required solution of the linearized system can be written as After obtaining the solution of the linearized system, the corrections are added to the solutions at the nth iteration and the procedure is repeated until convergence is achieved. This gives the solution at a given ξ i . The procedure is to be repeated at the next streamwise location ξ i+ and so on. In boundary layer flows, the greatest error is associated with the wall gradients f η (ξ , ), θ η (ξ , ), and φ η (ξ , ), and hence these are used to determine convergence. The iterations are stopped when the successive iterate values of the gradients match up to  - . Since Newton's method has second-order convergence, usually three to four iterations suffice to achieve the chosen tolerance.

Results and discussion
The problem of double diffusive convection induced by a horizontal wavy surface in a porous medium in presence of cross diffusion effect has been analyzed. The problem is governed by a system of coupled nonlinear parabolic partial differential equations ()-(). The Keller box method was used to find the numerical solutions of the problem. The amplitude of the wavy surface was assumed to be small and the wave phase was considered to be zero. The computations were carried out for the following range of parameter http://www.boundaryvalueproblems.com/content/2012/1/88      Figure (b). Figure  shows the effect of buoyancy ratio N on the local and mean Nusselt and Sherwood numbers. It is evident that the buoyancy ratio enhances both the local and mean heat and mass transfer coefficients. The buoyancy ratio enhances the local and the mean Nus-http://www.boundaryvalueproblems.com/content/2012/1/88  fer rates. Further, Nu x Ra -/ and Sh x Ra -/ exhibit fluctuations which increase with the streamwise coordinate ξ . These results regarding the heat and mass transfer coefficients coincide with those reported by Cheng [] with respect to the vertical wavy surface. The effect of cross diffusion coefficients on the slip velocity is shown in Figure . The slip velocity f η (ξ , ) is higher in the presence of cross diffusion effect as compared to the case when cross diffusion effect is absent.
The cross diffusion effect on the local and mean heat and mass transfer are depicted in Figure . These figures suggest that the presence of cross diffusion effects reduces both heat and mass transfer rates. The cross diffusion is more pronounced in case of heat transfer while the variation is infinitesimal in case of mass transfer. Figures (a) and (b) show the effect of the Dufour and Soret numbers on the slip velocity. Both parameters tend to accelerate the fluid in the boundary layer thereby increasing the slip velocity.
The effects of Dufour number on Nu x Ra -/ , Nu m Ra -/ , Sh x Ra -/ and Sh m Ra -/ is shown respectively in Figures (a)-(d). It is evident that the Dufour number reduces local and mean heat transfer rates while increasing the local and mean mass transfer rates. Here also we see the significant effect of D f in the case of heat transfer as compared to the mass transfer.
The effects of the Soret number on Nu x Ra -/ , Nu m Ra -/ , Sh x Ra -/ , and Sh m Ra -/ are shown in Figures (a)-(d). These results show that the Soret number enhances the local and mean heat transfer rates while reducing the local and mean mass transfer rates. The http://www.boundaryvalueproblems.com/content/2012/1/88 effect of the Soret number is the exact opposite of that of the Dufour number on heat and mass transfer.

Conclusions
The paper analyzed double diffusive convection induced by a horizontal wavy surface embedded in a porous medium taking the cross diffusion effect into account. The governing parabolic partial differential equations have been solved using the Keller box method. The convergence rate depends on the parametric values chosen. Computations show that the Lewis number enhances mass transfer while reducing heat transfer. The buoyancy ratio enhances both the heat and mass transfer rates. The surface geometry also plays a crucial role in controlling heat and mass transfer rates. The effect of the Dufour number is to reduce heat transfer and enhance mass transfer. The effect of the Soret number is the exact opposite of the Dufour effect. We observe reduced heat and mass transfer in the presence of cross diffusion terms. http://www.boundaryvalueproblems.com/content/2012/1/88 Author details 1 School of Mathematical Sciences, University of KwaZulu-Natal, Private Bag X01 Scottsville, Pietermaritzburg, 3209, South Africa. 2 Department of Mathematics, Bangalore University, Central College Campus, Bangalore, 560001, India.