Study on Double-Shear Test of Anchor Cable and C-Shaped Tube

(e free section of prestressed anchor cable is a weak part of support. A new supporting structure named Anchor Cable and C-Shaped Tube, which can bear transverse shear force, solves the problem that rock bolt and anchor cable are prone to shear failure in the free section and also solves the contradiction between high preload and low shear bearing capacity of support materials. Double-shear tests of Anchor Cable and C-Shaped Tube with smooth joint planes were carried out. Double-shear tests were carried out on the anchor cables with the diameter of 21.6mm and the same type of Anchor Cable and C-Shaped Tube under different preload conditions. (e influence of the preload on the shear performance of supporting materials and the enhancement effect of Anchor Cable and C-Shaped Tube supporting structure on the shear performance of anchor cables were analyzed.(e test results confirm that Anchor Cable and C-Shaped Tube can improve the transverse shear resistance of the supporting material and increase the axial ultimate bearing capacity of the anchor cable during the shearing process. It is found that, during the doubleshear test, the fracture form of the supporting materials is tensile fracture, and when it is sheared, Anchor Cable and C-Shaped Tube can reduce the stress concentration of the interaction between the joint surface and the surrounding rock and reduce the damage to the surrounding rock.


Introduction
e use of rock bolts and anchor cables has become an important and main support method for coal mine roadway support [1]. With the increasing depth of coal mining, the changeable geological structure in the environment of deep underground, the complex stress environment, and the large common deformation and failure of surrounding rock appear, while the conventional supporting methods show limitations [2,3]. Due to the inadaptability of ordinary anchor cables of the large deformation environment of surrounding rock, the breaking phenomenon occurs constantly, and the forms are different [4]. Besides the most common tensile breaking, there are also a large proportion of shear breaking, tension bending, and tension-shear combined breaking forms [5][6][7][8][9].
At present, in the design of roadway support, most of them only put axial bearing capacity into consideration without shear bearing capacity of rock bolt and anchor cable, and the shear fracture of rock bolts and anchor cables cannot be ignored [10]. Some studies have found that the fracture location of the anchor cable or rock bolt occurs at the position of the free section near 2 meters above the roof of the roadway [11], and other studies have found that the ultimate bearing capacity and displacement of anchor cable will decrease with the increase of prestress [12,13], which improves the probability of shear breaking of anchor cable. erefore, the free section of the prestressed anchor cable is a weak link that is susceptible to shear failure. Lin et al. studied the anchorage stress and deformation of the anchorage joint under shear action through direct shear test and found that the inclination angle of the bolt has an effect on the shear strength of the joint plane and improved the shear creep model of rock-like materials [14,15].
In order to adapt to the large deformation characteristics of deep surrounding rock, many supporting materials and supporting technologies have been invented by experts and scholars. For instance, anchor bolt with constant resistance and large deformation and NPR bolts/cables invented by He et al. well solved the problem of large deformation in deep soft rock roadway [16][17][18]. Also, the team of Kang et al. found that the prestress of rock bolt and its diffusion played a decisive role in supporting effect and proposed a high prestress and high strength supporting system, which achieved good results in many work sites [19][20][21]. Most of these technologies and materials aim at controlling the large axial deformation of surrounding rock but seldom consider the transverse loading of supporting materials. In order to solve the contradiction that the supporting material in free section is easy to break and the transverse bearing capacity and transverse displacement of the supporting material are easy to decrease due to high prestress [11][12][13], a supporting structure named Anchor Cable and C-Shaped Tube was invented to solve the problem that the anchor cable with high prestress in free section is easy to shear and break. e shear mechanical properties of the supporting structure named Anchor Cable and C-Shaped Tube were studied by double-shear tests in laboratory. In this provision, Anchor Cable and C-Shaped Tube shall hereafter be referred to as ACC.

Brief Introduction of ACC Supporting
Structure. ACC consists of two parts, anchor cable with high prestress and C-shaped tube. Figure 1 shows the physical drawing and schematic of ACC. e anchor cable with high prestress exerts axial compression force on the structural plane of surrounding rock by prestress, which increases the friction between joint planes, prevents the surrounding rock from dislocation on both sides of the structural plane, together with the dowelling function of anchor cable itself, and prevents the surrounding rock from axial shearing dislocation. e C-shaped tube is installed at the free end of the structure, which separates the exposed part of anchor cable or rock bolt from surrounding rock [22]. When shear dislocation occurs in surrounding rock, it would be separated from the free end of anchor cable or rock bolt. With the shear deformation of the structural plane, the C-shaped tube shrinks gradually to completely wrap the anchor cable, thus improving the shear stiffness and increasing the shear capacity of the free end of the supporting structure.

Analysis of the Mechanism of ACC.
After ACC is subjected to shear force, the shear part of slotted steel tube shrinks continuously and wraps the internal anchor cable (Figure 1(b)). When the free section of anchor cable bears shear force, it is restrained by locks and anchoring section at both ends. At this time, it could be seen as the simply supported beam under concentrated force. Assuming that the concentrated force acts in the middle of the simply supported beam and the length of the free section of anchor cable is l (m), according to the relevant formulas of material mechanics, the stress situation of anchor cable at the shear plane in elastic stage can be deduced as follows [23]: τ � F S πR 2 /2 (4R/3π) It can be seen from formula (2) that when the shear force is fixed, the tensile stress on the anchor cable decreases with the increase of its diameter. After installing the slotted steel tube, when it shrinks and deforms, the shear force acts 0 kN on the anchor cable, due to its certain bearing capacity. It indicates that ACC can absorb a certain shear load to protect the anchor cable, and its limit is F s1 (kN). It can be seen from formula (4) that the contracting stiffness of slotted steel tube K (kN/m) could be obtained by experiment. When the slotted steel tube and anchor cable form the bearing structure, the diameter of the supporting material is increased, and the additional axial force is reduced [23].
It can be seen from formula (3) that the shear stress of anchor cable decreases with the increase of cross-sectional area, which of the whole supporting structure increases due to the installation of slotted steel tube, so ACC bears less shear stress on the shear plane under the same shear force.
M is the bending moment (N·m) of the anchor cable on the shear plane. F S is the shear load (N) on the anchor cable, σ 1 is the initial axial stress (N/m 2 ) caused by prestress of anchor cable, and D (m) is the diameter of anchor cable. τis the shear stress (N/m 2 ) of the anchor cable on the shear plane.I z is the moment of inertia relative to the neutral axis (m 4 ). R 1 (m) is the inner diameter of slotted steel pipe before shrinkage, R 2 (m) is the outer diameter, the inner diameter after shrinkage is R 1 ′ (m), and the outer diameter is R 2 ′ (m).

Brief Introduction of Double-
Shear Instrument e schematic diagram and physical drawing of the selfdesigned and developed double-shear test system-tension and shear system of Anchor Cable (bolt) and C-shaped Tube are shown in Figure 2. In this system, the anchor cable is tensioned by locks in the same way as in the work site to provide prestress to the supporting materials. e maximum axial tensile load is 120 tons, and it equips a vertical loading system with a maximum vertical load of 600 tons in the middle. is system can apply shear force to the supporting materials, and the maximum shear displacement is 250 mm. e test samples are 3 concrete specimens of the same size 300 mm × 300 mm × 300 mm with 32 mm prefabricated holes in the middle, in which the supporting materials are installed for further tests. e test samples are restrained by three independent stainless steel shear boxes (Figure 2), and the shear boxes on both sides are restrained, respectively, by four beams and four screws. It can be seen from the schematic diagram in Figure 2(a) that the instrument has no force on the prefabricated joint plane but pure shear force, so the smooth joint plane is what the experiment studies.  Before the load After the load Shock and Vibration

Test Design and Preparation
In this experiment, double-shear tests were carried out on anchor cables with the diameter of 21.6 mm and the same type of ACCs, in order to study the influence of different prestress on the shear performance of anchor cable and analyze the effect of ACC supporting structure on the shear mechanical properties of anchor cables after the addition of C-shaped tube into ACC supporting structure. Table 1 is the test design table for this experiment. e specification of concrete specimen used in the test was 300 mm × 300 mm × 300 mm, and the ratio of water: cement: sand: gravel was 1 : 2 : 4 : 4. After pouring the specimen, a 100 mm × 100 mm small specimen was left for uniaxial compression test to determine the uniaxial compressive strength of the large specimen, which is shown in Table 1.
e uniaxial compressive strength of the test block was determined as 30 MPa according to the results of uniaxial compression test, and some test blocks are shown in Figure 3.

Analysis of Test Results
e test results are plotted in Figure 4 and summarized in Table 2 after the experiment. Due to a certain gap between the test block and the shear box, there will be a stage where the shear displacement increases, while the shear force remains unchanged during the test; and the effective shear displacement in the table refers to the shear displacement without this initial stage of the test.

Breaking Law of Supporting Materials.
e breaking law of the anchor cables with the diameter of 21.6 mm in doubleshear test is as follows. It can be seen from Figures 4(a) and 4(b) that it is not the same for the law between the curves of shear force-shear displacement and axial force-shear displacement.
e axial force has a relaxation stage (Figure 4(b), A) with the increase of shear displacement. is relaxation phenomenon is more common with the increase of prestress of anchor cable. e reason for the relaxation stage is that a part of the prestress will be transformed into resistance to the deformation of joint surface in the initial stage of shear deformation; and then it will enter the elastic stage (Figure 4(b), B), followed by the long plastic strengthening stage (Figure 4(b), C), and finally break (Figure 4(b), D). e breaking law of ACC of the anchor cables with the diameter of 21.6 mm in double-shear test is as follows.
As can be seen from Figures 4(c) and 4(d), the relationship between the shear force-shear displacement curves of ACC has gone through four stages. Stage A is stiffness strengthening stage (Figure 4(c), A). Stage B is elastic stage (Figure 4(c), B). Stage C is shear yield stage (Figure 4(c), C). Stage D is fracture stage (Figure 4(c), D); and the four stages are same for the axial force and anchor cable, shown in Figure 4(d). In the stage a of shear force-shear displacement curve, when ACC is under shear load, the slotted steel pipe can shrink with the increase of shear displacement to wrap the anchor cable, so that the slotted steel pipe and the anchor cable can bear the load together, which improves the initial shear stiffness of the support material.

Analysis of Material Failure Mode.
Breaking the concrete after experiment, it is required to analyze the failure mode of supporting material and concrete blocks. Figure 5 shows some representative blocks and supporting materials after demolition. Figures 5(a)  During the double-shear test, the intermediate block is continuously subjected to the reaction force of supporting material. Plastic deformation occurs continuously on concrete blocks until the whole block splits from parallel drilling direction, because the stiffness of it is lower than that of the supporting material. However, due to the limitation of the shear box, the test block can still apply the load on the supporting material, the test block continues to expand, and the crack continues to expand until the supporting material is broken.
Crack propagation mode of the test block indicates that the cracks of the concrete block are radial after the doubleshear test of the anchor cables with the diameter of 21.6 mm, while those of the concrete block of the ACC of anchor cables with the diameter of 21.6 mm are split. is is because the anchor cable is structured by many steel strands which makes uneven reaction force on the surrounding rock and increases the possibility of stress concentration. However, the C-shaped tube of ACC is circular, which can reduce the degree of stress concentration and the damage to surrounding rock. e failure mode of supporting materials is as follows. It can be seen from Figures 5(b) and 5(d) that the supporting material presents with the shape of spreading wing after being sheared and is broken near the shear plane.
rough the analysis of the fracture of two kinds of supporting materials, it is found that there is obvious necking phenomenon in the fracture of two kinds of anchor cables, and the anchor cables are tensile fracture. ACC is protected by slotted steel pipe. When subjected to shear force, the C-shaped tube near the shear plane shrinks to wrap the anchor cable and bear the load together with the anchor cable. When anchor cables break successively inside, there   are no steel strands supporting on one side of the internal C-shaped tube. But, at this time, it has been locked by the expanded rock sample to bear both shear and tension force under shear force; and the tensile-shear failure occurs once the C-shaped tube reaches the limit of bearing capacity.

Analysis of Bearing Capacity of Supporting Materials.
Analysis of shear bearing performance: it can be seen from Figure 4(e) that, with the increase of shear displacement, ACC with C-shaped tube on anchor cable has significantly higher ability to resist shear deformation than that of the   same type of anchor cable. Under the same shear displacement, the shear force of anchor cables with different prestress is generally less than that of ACC, and the shear displacement of ACC is also larger than that of the same type of anchor cable when reaching the limit of shear capacity. It shows that ACC can improve the shear stiffness and ultimate bearing capacity of internal anchor cable. e key data of double-shear test are listed in Table 2. Figure 6(a) shows the shear capacity and shear displacement at ultimate shear capacity of anchor cables with the diameter of 21.6 mm with the increase of prestress under the same conditions. It can be seen from Table 2 and Figure 6(a) that, with the increase of preload, the shear bearing capacity of the anchor cable has a downward trend, while the shear displacement is not significantly affected. Figure 6(b) shows the shear capacity and shear displacement of ACC with the diameter of 21.6 mm with the increase of prestress under the same conditions. It can be seen from the figure that when the C-shaped tube becomes supporting structure of ACC, the shear bearing capacity is greatly improved, and its shear capacity has been greatly increased by at least 30.5%. Compared with the anchor cables with the diameter of 21.6 mm, the shear displacement also increases to a certain extent, with the minimum increasing by 7.1% and the maximum by 29.9%.
By comparing the two types of data, it can be seen that the ACC supporting structure improves the shear bearing capacity of the internal anchor cable, and, after using the ACC supporting structure, it can have a stronger ability to resist shear deformation.
In the analysis of axial bearing capacity, it can be seen from Figure 4(f ) that when it reaches the ultimate shear capacity, the value of ultimate axial bearing capacity of both the anchor cable and ACC is close; namely, the greater the prestress, the slower the growth rate of axial force with the increase of shear displacement, but ultimately it reaches the tensile yield load with similar numerical value. According to the statistical data in Table 2, compared with the anchor cable, the ultimate tensile load of ACC supporting structure has been slightly optimized, with the maximum optimization rate of 9.6% and the minimum of 4.9%.
Above all, the ultimate shear capacity of the anchor cable is negatively correlated with the prestress. Under the same prestress, ACC can enhance the shear stiffness of the internal anchor cable and the resistance of shear deformation with a lifting rate of more than 7.1%; it can also increase the  Shock and Vibration ultimate shear capacity of the internal anchor cable with a lifting rate of more than 30.5%. ACC can improve the axial bearing capacity of the inner cable by a small margin, which is more than 4.9%.

Conclusion
rough the double-shear test of the prestressed anchor cable with diameter of 21.6 mm and ACC supporting structure of the same type, the following conclusions are obtained: (1) ere is a negative correlation between the ultimate shear capacity of anchor cable and its prestress. e greater the pretension, the weaker the shear capacity. erefore, the shear bearing capacity of the free section of the prestressed anchor cable will be reduced when the high pretightening force is applied, and there is a risk of shear fracture.
(2) rough the analysis of the failure mode of surrounding rock on both sides of joint surface, it is found that the stress concentration of ordinary anchor cable will occur in the process of shearing due to the structure of steel strand itself, which will deepen the damage to the surrounding rock of structural plane. However, ACC could alleviate the degree of stress concentration of the interaction between supporting structure and surrounding rock and reduce the damage to surrounding rock. (3) ACC can improve the shear stiffness and the resistance of shear deformation of the internal anchor cable under the same prestress, with the lifting rate of more than 7.1%; the ultimate shear capacity of the internal anchor cable can be increased by more than 30.5%; and the axial bearing capacity of the internal anchor cable can be slightly improved by more than 4.9%. ACC supporting structure has the ability to eliminate shear fracture of anchor cable with high prestress in free section.  Shock and Vibration 9