Experimental Investigation on Effect of Partial Replacement of Cement with Bamboo Leaf Ash on Concrete Property

Ethiopia’s construction industry is aggressively expanding than ever before. Cement is themost essential and expensive material in this regard. Cement takes 10%–15% by volume of concrete. Nowadays, the construction industry is challenged by the scarcity of cement and price escalation of the cement market. However, scholars try to replace cement with pozzolanic material. Besides this, they investigated that bamboo leaf ash possesses pozzolanic properties. Ethiopia has about 850,000 hectares of lowland bamboo, so it is good to utilize bamboo leaf ash as a replacement material for cement. In this study, the capability of lowland Ethiopian bamboo leaf ash as a partial substitute for cement in C-25 concrete production with 0%, 5%, 10%, 15%, and 20% replacement of OPC by BLA with 0.49 percent water-to-cement ratio was investigated. )is study examines the chemical properties of BLA, physical properties of cement paste, workability, compressive strength, water absorption, density, and sulfate attack of concrete. )e chemical composition of bamboo leaf ash was examined, the summation of SiO2, AlO3, and FeO3 is 76.35%, and the ash was classified class N pozzolan. )e normal consistency percentage of water increases as the BLA replacement amount increases, and both initial and final setting time ranges increase as the BLA replacement amount increases. )e compressive strength of concrete for 5% and 10% BLA achieves the target mean strength (33.5MPa) on the 28th day, and on the 56th day, 5% and 10% replacements increase the concrete strength by 1.84% and 0.12%, respectively. )e water absorption and sulfate attack have significant improvement of the BLA-blended concrete on 5% and 10% BLA content. According to the findings, bamboo leaf ash potentially substitutes cement up to 10%.)e outcome of the study will balance the cement price escalation and increase housing affordability without compromise in quality.


Introduction
Concrete is a substance that is made up of several different components that contain a binding base where there are embedded particles or fragments of aggregates [1]. Concrete is composed of cement, aggregates, chemical admixtures, mineral admixtures, and water and encompasses all artificial materials in quantity. Concrete utilization on our planet Earth is in billions of tons. us, one million metric tons of CO 2 are produced per annum due to cement consumption and production, which, in turn, causes environmental threats [2]. e manufacturing of portland cement is expensive with energy consumption at a very high temperature. e cement industry roughly emits 900 kg of CO 2 every 1,000 kg of cement, with around 5% of all carbon dioxide emissions [3]. When manufacturing portland cement burning at a large rotary kiln at an approximate temperature of 1,400°C, the amount of coal required to manufacture 1 (one) ton of cement is between 100 kg and about 350 kg [4]. Cement manufacturing needs much energy consumption and releases harmful gas to the environment, polluting the atmosphere. Partial cement replacement with locally available material will reduce the amount of energy and environmental impact. It is a good way to use agricultural waste, an industrial by-product, and plant residual in the designated position of portland cement to reduce the consumption of the raw materials, protect the environment, and enhance the quality of cement. Partial replacement of cement with waste material that has pozzolanic properties in concrete production is a worldwide practice [5]. Nowadays, some agricultural by-products and wastes are attracting much research because of their pozzolanic content for use as additives in commercial portland cement [6]. e performance of concrete is commonly improved due to the hydration phase during the pozzolanic reaction. Several research studies on the use of bamboo leaf ash (BLA) as a pozzolanic material in the making of concrete have been undertaken across the world. [7] investigated that the bamboo leaf ash is a good pozzolanic material that reacts with calcium hydroxide forming calcium silicate hydrate. e pozzolanic activity of bamboo leaf ash increases with the increase in time and temperature. [8] concluded that BLA can be used as a natural pozzolan to replace cement in concrete production. [9] investigated that for concrete grade M-20, from the results, the measured value of maximum load and compressive strength of 5% blended concrete was higher than that of OPC (0%) concrete. But, only 5% and 10% blended concretes reached the target strength. However, nothing has been done, based on the findings, to investigate the viability of using Ethiopian BLA for this purpose. However, Ethiopia is gifted with huge bamboo resources. According to the records, Ethiopia has around 1 million hectares of bamboo forest, accounting for around 67 percent of African bamboo forest cover and 7% of global bamboo forest cover [10]. e availability of bamboo, the low technology required to process it into ash, and its pozzolanic reaction necessitate its usage as a material for the production of some building elements for affordable housing provision, especially in developing countries. As a consequence, this study aims to find out how bamboo leaf ash mixed with cement affects the qualities of concrete. An experimental investigation will be carried out to examine the impact of partial replacement of BLA on the mechanical and physical properties of concretes such as consistency, setting time, workability, compressive strength microstructure, and durability.

Cement.
For this study, ordinary portland cement (OPC), which is manufactured from a Dangote cement factory, was available at markets and tested according to the ASTM standards. Table 1 illustrates the physical properties of the cement, Figure 1.

Bamboo Leaf.
e bamboo leaf used for this study was taken from Awi Zone, Ethiopia. One metric ton of bamboo leaf was collected from the source and then sun-dried, and it was burnt in an open environment before being burned in a furnace for two hours at 600°C in which it was found to be an amorphous material containing amorphous silica [7]. is is to remove extra carbon in the ash. Bamboo leaf ash is produced at the DTU Chemistry Department laboratory. After the bamboo leaf was burned, it was sieved through a 75 μm; the ash that remained was ground using a small mill machine found in Debre Tabor University's Faculty of  Computing's mechanical unit operation laboratory. Physical  and chemical compositions of BLA used for this study are as  shown in Tables 2 and 3. e ASTM standard was used for physical property testing. e analytical methodologies are LiBO 2 , fusion, HF attack, gravimetric, colorimetric, and AAS. In November 2020, the Ethiopian Geological Survey's Geochemical Laboratory Directorate conducted the test. e fineness of the ash retained on 45 μm (No. 325) sieve is 30.50%, which is less than the maximum value of 34% specified by ASTMC 618.

Coarse Aggregate.
For this study, the crushed aggregate of basaltic rock was used. e size of the maximum aggregate size is 25 mm. e types and methods of tests are given in Table 4.

Fine Aggregate.
For the sake of this specific study, river sand was used as a fine aggregate. e following tests and methods are conducted as given in Table 5

Mix Design.
In this specific study, the mix design of concrete with determined ratios of cement, sand, water, coarse aggregate, and BLA was proportioned for a C-25 concrete grade based on the ACI mix design method. e trail mix was organized for characteristic strength of 25 MPa, while the water-to-cement ratio was 0.49 and ordinary portland cement content was 365 kg/m 3 . Table 6 shows the mix code designation for the proportioning.

Mix Proportioning.
e mix proportion of concrete ingredients was performed following ACI 211.1 mix design practice. A total of 72 cubes were prepared in five series of concrete mixes. ese ratios were 0%, 5%, 10%, 15%, and 20%. Here, it was prepared as a control mix OPC without the addition of BLA, whereas the remaining four series of concrete mixes were prepared by partial replacement of OPC with different percentages of bamboo leaf ash. e water-tocement ratio of all the series of concrete mixes was kept constant at 0.49. e summaries of the mix proportion of all series of concrete mixes are shown in Table 7.

Specimen Preparation.
e following sampling methods were applied to this study. For each cement replacement percentage, three 150 mm x 150 mm x 150 mm cube samples were produced with BLA replacement percentages of 0%, 5%, 10%, 15%, and 20%. Concrete specimens were cast and    Moisture content 0.53% ASTM-C566  cured in the open tank for 3rd, 7th, 28th, and 56th days having 3 cube specimens for each duration and mix type. e concrete specimens with a total of 12 cubes were cured in the open tank for 7 days and kept in the open environment for 2 days, and then, the specimen is weighed and immersed in 5% Na 2. SO 4 solution for 56 days to test the sulfate attack. A total of 12 cubes were cured in a tank for 28 days and then checked the water absorption of the concrete cube for each percentage replacement.

Testing of Specimens.
e slump test is carried out as per the procedures mentioned in ASTM C143. ASTM 143 reports that the slump value is measured in terms of inch (millimeters) to the nearest 1⁄ 4 inches (5 mm) of subsidence of the specimen during the test. e compressive strength test of concrete was conducted on a concrete cube of 150 mm × 150 mm x 150 mm on 3rd, 7th, 28th, and 56th days using a compressive strength testing machine, which has a maximum capacity of 2,000 KN. e average compressive strength of the three specimens was the strength value.
In this study, the durability of concrete will be examined by water absorption and sulfate attack. To examine the sulfate attack, the casted concrete cubes are soaked in 5% Na 2. SO 4 solution to examine the sulfate attack (durability) through testing the compressive strength of concrete before and after soaking into solution. While the minimum distance between the cubes was at least 25 mm, the casted cube specimens were placed in the oven; the specimen was dried in the oven in which the temperature was controlled at 110°C for 72 hours. e dried specimen was cooled for 24 hrs, before measuring the weight of the specimens. Subsequently, the dried specimen was soaked in water for 24 hrs. Next to this, the specimen was removed from the water and the weight of the specimen was again measured. e water absorption of the specimens was determined to know the water absorption capacity and durability of concrete.
BS 1881: Part 122 states that the absorption test shall be performed when the age of the concrete is from 28 days to 32 days. e drying of concrete specimens shall begin at an age of 24 days to 28 days. For this study, 28th-day concrete specimens were selected for the water absorption test. e sulfate attack test shall be made when the age of concrete is 56 days. e water absorption, expressed in percentage, was then computed using the following equation [11].
where M w is the mass of wet specimen after immersion in water for 72 hours, and M d is the mass of oven-dried specimen before immersion in water.

Slump Tests.
One of the most essential qualities of fresh concrete is its workability. e slump test is the simplest workability test for concrete, due to its low cost, and also provides immediate results. Concrete should be workable enough to cast, consolidate, and finish; therefore, in all types of mixes slump tests were performed to determine the workability of freshly mixed concrete. e Ethiopian standard makes no mention of a workability test. e slump test is carried out as per the procedures mentioned in ASTM C143. ASTM 143 reports that the slump value is measured in terms of inch (millimeters) to the nearest 1⁄ 4 inches (5 mm) of subsidence of the specimen during the test. e summaries of the slump test results are as shown in Table 8 below.
As shown in Table 8, as the replacement percentage of BLA increases, the slump value goes down. erefore, the probable reason was due to the fineness of BLA and their large specific surface area though all other factors are constant [12]. Finer particle requires more water to wet their larger specific surface area. But up to 10% replacement level, the slump is still in the estimated range of 25 mm to 50 mm.

Dry Density.
e density of hardened concrete is determined based on the volume and the weight of the concrete cube. However, the weight of the specimens was measured just before the compressive strength testing was conducted.
Here, the density of concrete specimens is calculated by using the 28th-day weight and the result is as shown below in Table 9.
Referring to Table 9, the density of concrete decreased as the percentage of BLA replacement levels increased. e probable reason is that the specific gravity of Dangote OPC cement (3.15) is higher than bamboo leaf ash with a specific gravity of 2.15, and referring back to section Physical Properties of BLA, unit weight is 1,217 kg/m3 that is lighter than OPC cement of 1,400 kg/m3. e density reduction shown in this table is for the 28th day. Here, the density reduction is compared with the reference mix of OPC control with BLA5, BLA10, BLA15, and BLA20; therefore, the density reduction is 0.25, 0.89, 1.67, and 2.06, respectively.
Based on the results shown in Table 9, there is a major reduction in density, while the percentage of BLA replacement level is raised. e reduction in concrete density is an important property of concrete to build high-rise buildings, consequently, suitable for lightweight concrete construction.
erefore, the replacement of cement with BLA is very important to construct economical buildings and reduce building failures (settlement) due to heavy selfweight. e density of hardened concrete obtained from this study obtained similar results when compared with those of the studies of [13][14][15].

Compressive Strength.
e compressive strength test of concrete is the main test conducted on the properties of hardened concrete. Here, the test was performed for all of the concrete cubes on the 3rd, 7th, 28th, and 56th days after the casting date using a compression testing machine. For each of the results, the average values of three cubes were taken as their compressive strength. e overall compressive strength test result for all of the concrete cubes is as shown in Figure 2 below.
From Table 10, the compressive strength of concrete was checked taking bamboo leaf ash (BLA) as a partial replacement for cement up to 10%, and the OPC control achieved the target mean strength of 33.5Mpa after 28 days; however, the mix designations for BLA15% and BLA20% did not. However, the compressive strength values of BLA15% and BLA20% were 30.47 MPa and 27.88 MPa, respectively, and they attain the characteristic strength of 25 MPa on the 28th day.
From Table 10, BLA5%, BLA10%, BLA15%, and BLA20% had shown the compressive strength reduction by 4.27%, 4.86%, 16.65%, and 27.76% respectively, as compared to the OPC control mix on the 28th day. is indicates that the compressive strength of BLA-blended concrete decreases with an increase in BLA content. e reason for compressive strength reduction is due to the high replacement of BLA and cement content reduction per cubic meter of concrete by 5%, 10%, 15%, and 20% from the normal concrete mix, also the pozzolanic reaction takes a long time, and this leads to compressive strength reduction [16]. e compressive strength of normal concrete and concrete blended with BLA at the curing age of 3rd, 7th, 28th, and 56th days is displayed in Figure 2. It can be observed that BLA as a partial substitute for cement up to 10% and OPC control meet the goal mean strength of 33.5 Mpa at 28 days, but the mix designations for BLA15% and BLA20% did not. However, the compressive strength values of BLA15% and BLA20% were 32.32 MPa and 29.51 MPa, respectively, and they attain the characteristic strength of 25 Mpa on the 28th day. ere was also a subsequent strength increase at 56 days for percentage replacement from 5% to 10% replacement and a decline in strength at 15% and 20% replacements as compared to the reference mix. e average compressive strength value of 5% and 10% BLA on the 56th       [7]. e data on top of the bar chart are the standard deviation of compressive strength.
Referring to Table 10, the percentage increase at 56th day compressive strength test relative to the control sample at 5% and 10% replacements was 1.84% and 0.12%, while the percentage decrease at 15% and 20% BLA replacements relative to the control sample was by 3.24% and 4.45%. e increase in strength could be a result of the presence of a high amount of silica (SiO2) 65.66% in the ash and the amount of CaO is 15.22% which was responsible for the formation of tricalcium silicate and dicalcium silicate which both do oxidize with water to form a C-H-S bond (calcium silicate hydrate) which was the determining factor for strength gain [1]. e optimum strength was recorded at 10% BLA replacement at 56th day curing age. It could be that C-S-H is most effective at 10% BLA replacement. e compressive strength obtained from this study found better results when compared with those of earlier studies [13][14][15].
Referring to Table 11 and Figure 2, for all concrete mixtures of BLA with their respective curing ages, the mean standard deviation is less than 15%. e concrete mix was performed according to the mix design procedures and techniques as per validity analysis. e degree to which the results of a measure (experimental work) accurately reflect the variable for which they were designed is known as validity. e mean compressive strength of concrete for each specimen and the curing age were the main experimental work (test) variables in this study.
is variable was validated by comparing it to the designrequired target mean strength and analyzing the standard deviation between concrete cube specimens for each curing duration. Concrete's compressive strength increases with curing time. One method for determining the validity of the mean compressive strength test results is to use the standard deviation of the concrete cube specimen. If the individual variation is less than 15% of the average, the average of three specimen values shall be taken as representative of the batch, according to Indian Standard, 2006. ere is no detailed information about this in any Ethiopian concrete standard.

Water Absorption.
e overall water absorption test result for all of the concrete cubes is as shown in Table 12 below.
Referring to Table 12, the water absorption of BLAblended cement concrete cubes is shown. A general BLA10% water absorption is higher than control OPC and then starts increasing from 15% to 20%. e percentage water absorption ranges between 2.9% and 3.6% with the least value attained at 5% BLA (2.90%) content, and the greatest value of 3.6% is attained at 20% BLA content on the 28th day. e water absorption of the 5% and 10% BLA-blended cement concrete specimens did not have much water absorption as the reference, which is an indication of the integration of BLA in the voids thereby causing impermeability. e decrease in water absorbed at lower BLA replacement is also qualified to the initial filling of the voids by the BLA ingredient. e decrease in water absorbed at lower BLA replacement may be attributed to the initial filling of the voids by the incorporated BLA [11]. However, at higher levels of BLA substitution, there was an insufficient quantity of calcium hydroxide to react with the excess BLA, thus creating pores in the mixture and thereby increasing the water absorption. is finding agrees with previous observations by [11,14].

Sulfate Attack Analysis.
e effect of BLA replacement on sulfate resistance was examined after 56 days of curing age. e BLA-blended concrete sulfate resistance result is expressed in terms of compressive strength loss. e result is presented in Figure 3 below. e compressive strength loss due to sodium sulfate attack after immersing the specimens for 56 days in the 5% sodium sulfate solution for the control mix (BLA0%) was assessed as 4.58%. As referring to Figure 3, the BLA-blended mix, BLA5%, BLA10%, BLA15%, and BLA20% suffered 3.37%, 3.93%, 4.63%, and 4.79% strength loss at their age of   Advances in Civil Engineering 56th day. Maximum strength loss was experienced in BLA 20%, whereas minimum loss was noticed in BLA5%. Loss of strength increased with BLA as the replacement amount increased. But, BLA10% strength loss is higher than control OPC loss of strength that increased with BLA content. Sodium sulfate reacts with calcium hydroxide and hydrated calcium aluminates. It completely decomposes the hydrated calcium silicates and makes the concrete a friable mass [17,18]. Resistance to sulfate attack is found more in concrete made with 5% and 10% bamboo leaf ash due to a rise in homogeneity and decrease in sorptivity [19]. e result obtained from this study found better results when compared with those of the study by [20]. According to [20], investigation of OPC/BLA-blended cement concrete at 10% replacement was performed better in Na 2 SO 4 solution over that of OPC concrete cured in the same medium solution at 56th-day curing age. e OPC concrete in Na 2 SO 4 solution shows signs of strength loss from 23.64 to 21.82.

Regression and Correlation.
In regression analysis, the value of at least one independent variable is used to predict the value of a dependent variable. It explains how changes in an independent variable influence the dependent variable. e dependent variable in this case was compressive strength, while the independent variable was density. Origin Pro 2021 was used to simultaneously calculate the linear regression equation and correlation. e degree of association (linear relationship) between two variables is determined using correlation analysis. It is all about how strong the relationship between variables is. e sample correlation coefficient "r" is a measure of the strength of the linear relationship between the sample observations. Pearson's correlation coefficient (r) is unit free; it ranges between −1 and 1. Hence, −1 is a negative relationship, 0 is the weaker or no relationship, and 1 is a positive linear relationship [21].

Density and Compressive Strength.
It is drafted as a linear equation with two variables (X and Y). For three cube specimens, X is the average density of concrete. Under various BLA additions, Y represents the average compressive strength of concrete. e sample correlation coefficient is a measurement of the strength of the linear relationship between the experimental results. Figure 4 shows that the compressive strength of concrete increases with curing age as the density of the concrete increases. It demonstrates that the compressive strength and density of concrete are directly proportional variables. e 28th-day compressive strength has a significant positive correlation (0.960) as related to the 28th-day concrete density, as shown in Figure 5. In line with this, as stated in the previous sections, Pearson's correlation coefficient (r) is between −1 and +1. Based on this, the correlation coefficient is +0.960, which is a nearly positive one, arguing that the 28th-day compressive strength and 28th-day density have a direct relationship.
According to Figure 6, the compressive strength of concrete increases as the density decreases for the control mix, 5% BLA replacement, and 10% BLA replacement but decreases for the other mixes as the density decreases on the 56th-day curing age of concrete. On the 56th day of curing, Table 4 shows that the compressive strength of concrete decreases as the density of the concrete decreases. It demonstrates that concrete compressive strength and density are proportional variables for 15% and 20% BLA replacement. e coefficient of correlation between the 56th-day compressive strength and the 56th concrete density is 0.343. is result agreed with the previous regression analysis. Referring to Figure 6, the compressive strength of concrete increases as density decreases for the control mix, 5% BLA replacement, and 10% BLA replacement at the 56th-day curing age. is explains why there is less correlation between compressive strength and density at the 56th-day curing age.

Water Absorption and Compressive Strength.
e sample correlation coefficient is a measurement of the strength of the linear relationship between the experimental outcome and the sample correlation coefficient. e average of all mix compressive strength and water absorption value at the 28th-day curing age was used to calculate the correlation. e formula is a two-variable linear equation (X and Y). For three cube samples, X represents the average water absorption of curing concrete on the 28th day, and Y represents the average compressive strength of concrete at various BLA replacement levels.
e regression graph of Figure 7 demonstrates that the compressive strength of concrete decreases as the water absorption of the concrete increases. It demonstrates that the compressive strength and water absorption of concrete are inversely proportional variables. e 28th-day compressive strength has a significant negative correlation (−0.931) with the 28th-day water absorption (%). is correlation analysis shows that water absorption and concrete compressive strength had a negatively strong relationship. Accordingly, Advances in Civil Engineering this study proved that as water absorption percent increases the compressive strength decreases.

Water Absorption and Density of Concrete.
e correlation was calculated using the average of all mix density and water absorption values at the 28th-day curing age. e formula is a two-variable linear equation (X and Y). For three cube samples, the average water absorption of 28th-day cured concrete is X and Y represents the average density of concrete at various BLA replacement levels.
According to the regression analysis illustrated in Figure 5, the density of concrete decreases as the water absorption of the concrete increases. It indicates that concrete water absorption and density are inversely proportional variables. Referring to Figure 5, the 28th-day concrete density has a substantial negative connection (−0.892) with the 28th-day water absorption percentage. According to this correlation finding, there is a negative link between water absorption and concrete density. As a result, the study demonstrated that as the percentage of water absorption increases, the density decreases.

Conclusions
BLA was utilized as a cement-substituting material on concrete production based on experimental investigation, from which the following conclusion was derived. e workability of concrete decreases as the BLA replacement amount increases, but the setting time, water percentage for consistency, and soundness of cement paste all increase. On the 28th day, the compressive strength of concrete made with partial replacement of cement by up to 10% attains the target mean strength (33.5 MPa), and there are 1.84% and 0.12% enhancements in compressive strength values for 5% and 10% replacements compared to the control mix on the 56th day, while the density reduced as the BLA replacement increased. e water absorption of the BLA-blended concrete was lower than the reference at 5% and 10% BLA content, and the BLA-blended concrete showed significant sulfate attack resistance, particularly when compared to the reference. Based on the study of compressive strength and durability (water absorption and sulfate attack), 10% replacement of cement by BLA is the optimum percentage for obtaining maximum strength values.

Data Availability
e experimental data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest
e authors declare that there are no conflicts of interest.