Safety Management System Prototype/Framework of Deep Foundation Pit Based on BIM and IoT

,


Introduction
Urban development often requires the use of underground space. As a result, deep excavation pits for foundations have become more and more common in building construction. Underground space, which today may contain shopping malls, subways, parking lots, civil defence projects, and so on, provides the necessary services to promote social and economic stability. According to the safety regulations and rules [1] in China, deep foundation pit refers to all construction work including the excavation, support, and dewatering of foundation pits with excavation depths of 5 meters and above. A pit with a depth of less than 5 meters could also be considered a deep foundation pit if the surrounding environment is complicated. Due to the large amount of engineering, tight construction periods, low safety reserves, and high uncertainty of deep foundation pit engineering, safety accidents occur. e incidence of accidents in the construction industry remains high. Not only do they impact construction periods, they also cause huge economic losses and casualties.
At the same time, the safety management of deep foundation pits in the construction industry is relatively backward. Extensive research has been conducted on the causes of foundation pit accidents. Many of these accidents, according to Lin and Hadipriono [2], are a result of poor dewatering procedures, inadequate lateral bracings, poor workmanship during construction, poor consideration of soil pressures, and lack of monitoring. By analyzing deep slump failures and shallow slump failures in expansive soil, which underlie most of Hefei District, Zhang and Wu [3] realized that the frequent foundation pit accidents in that district were due to ignorance of the characteristics of expansive soil. Water inrushes and unchecked engineering geological data have also been identified as important causes of foundation pit accidents [4][5][6]. Hu et al. [7] identified design and construction factors such as insufficient embedded pile depths and insufficient anchor pull-out resistance as being responsible for foundation pit accidents. Having dynamic loads around deep foundation pits is also a factor in pit collapse [8]. In addition, Xu et al. [4] also identified several main risk events that can cause foundation pit accidents, including failure to follow engineering design, collapse of pit bracing structures, falling from a significant height due to a lack of edge protection, and collapse of the pit due to excavation. Leakage of the diaphragm wall, strut collapse, soil slide in the pit, and pit bottom upheaval are also identified as foundation pit accident causation factors [9]. A series of other factors have also been found to be indirectly responsible for foundation pit accidents. Qian and Lin [5] identified indirect causes of safety accidents in China which were also indirectly responsible for foundation pit accidents. ese causes included individual and departmental interests, safety inspections becoming a mere formality, malfunctions of governmental supervision, inadequate employment systems, and an ambiguous experts' system. Other indirect factors identified were attitudes to safety, inadequate construction site safety, market restrictions, and task unpredictability [10]. e development of Building Information Modeling (BIM) and communication technologies encourages the construction industry to enhance its management capabilities and modernization level. Technology can play an important role in identifying hazards on a construction site [11]. BIM has the features of integration, simulation, and visualization. It helps safety managers to identify and manage safety risks [12,13]. Communication technologies, such as radio frequency identification (RFID), ultra-wideband (UWB), and wireless sensor network (WSN), have also emerged as means by which construction sites are monitored [14]. Some of them have been used in recent years to enhance the safety performance of construction workers and equipment [15]. However, most studies of BIM related to construction safety focus on single application research such as fall hazard identification [16,17], workers training [18], and equipment layout planning [19]. Deep foundation pits are complex sites and regulated as being highly hazardous projects. Although real-time data collection by IoT technologies has been studied and applied in some construction practice, most data are shown in 2D site map rather than BIM platform. More importantly, the established real-time data prototype or frameworks could be further tested with more real-world cases. e interoperability among multiple technologies (e.g., BIM and wireless sensor), which allows information exchange during real-time data collection and processing, needs to be further studied [20].
Considering the safety need for addressing both precise position tracking and real-time on-site monitoring, this paper chose BIM and IoT technologies to create a construction Safety Management System of Deep Foundation Pits (SMSoDFP). e deep foundation pit was chosen as the study object to develop a prototype system framework for (1) identifying and visualizing the potential hazardous areas during design, (2) integrating the sensor data in BIM model during construction, and (3) providing early warnings and visualized tools in the BIM model according to the monitoring data in web platform. e structure of this paper is as follows. Section 2 proposes a system framework of Safety Management System of Deep Foundation Pits (SMSoDFP) according to the hazard identification and then describes the functional requirements of the safety system and the information that needs to be collected. Section 3 explains the operational principles of the safety management system. Section 4 presents a case study. Finally, possible implementation issues, conclusions, and recommendations for future research are presented in Section 5.

Hazard Identification Based on FTA.
In addition to their particularity, deep foundation pits have characteristics similar to other building sites during construction. Besides excavation and dewatering engineering, deep foundation pit construction also involves many kinds of construction equipment and machinery, such as scaffolding, formwork, cranes, and trucks. According to the annual accident statistics report in the website of the Chinese Ministry of Housing and Urban-Rural Development, the most common accident types related to building construction also exist in the construction phase of deep foundation pits. ese accident types mainly include collapse, falling, mechanical injury, object strike, and adjacent environment damage.
Among the above five types of accidents, falling, mechanical injury, and object strike are common accidents which could happen in any building part. e other two types, collapse and adjacent environment damage, are closely related to the construction of deep foundation pit.
ere are many causation analysis methods in safety management theory by which accident hazards are identified, including Fault Tree Analysis (FTA), Analytic Hierarchy Process (AHP), Safety Check List (SCL), Job Safety Analysis (JSA), Systems-eoretic Accident Model and Process (STAMP), expert interviews, and statistical analysis. FTA is one typical and common method for hazard identification and accident causation mechanism analysis. It is a top-down, deductive failure analysis in which the undesired state of a system is analyzed using Boolean algebra to combine a series of lower-level events. By analyzing 100 accident cases related to deep foundation pits from the public report and news in China over the last five years, the accident FTAs of collapse and adjacent environment damage are drawn as Figures 1 and 2.
In the FTA of collapse accident (Figure 1), 12 factors caused collapse of deep foundation pit. All the 12 factors develop 9 AND gates and 3 OR gates.
e Boolean expression is shown in the following equation: According to this Boolean expression, we can find 26 groups of Least Cut Set and 4 groups of Least Path Set. By calculating the structure weight of the 12 factors, the importance sequence is . We can find that absence of proper monitoring equipment and untimely monitoring data process are the top two key factors which cause collapse of deep foundation pit. Similarly, FTA of adjacent environment damage ( Figure 2) shows that the top key factors are the monitoring problems including absence of proper monitoring equipment, untimely monitoring data or hazardous processing, and improper warning value of monitoring. us, the following Safety Management System of Deep Foundation Pits (SMSoDFP) will focus on the above factors related to monitoring problems by BIM and UWB technology.

Basic Framework of SMSoDFP.
By analyzing and designing the functional requirements, the basic framework of Safety Management System of Deep Foundation Pits (SMSoDFP) is proposed as shown in Figure 3. e basic database of monitoring deep foundation pits includes hazardous area information, structural monitoring point, and workers' position information. All the above safety monitoring information was mapped and linked to the element attributes of the BIM model. By the development in the Revit API (Application Program Interface) and JavaScript language, Revit model could be uploaded to web platform and on-site monitoring information could be visualized in the same web platform. It has the functions of visualizing hazardous areas, monitoring personnel position, and providing early warnings of structural deformation.
is macro SMSoDFP framework consists of three modules (shown in Figure 4) which realize the real-time automatic analysis, the early warning of structural deformation, and the unsafe behavior of personnel on the construction site of a deep foundation pit. e first of the three modules is the data collection module.
is module is used to collect the information related to site safety during the construction phase. is information is collected primarily through structural health monitoring techniques such as wireless sensing technology and real-time location technology. e data collection module sends all the information obtained to the data processing module. e second module is the safety BIM model creating module. By editing family parameter information and parameter expressions in Revit, safety rules can be expressed in BIM model. rough the condition setting of the "IF" function of Revit, the initial display can be effectively controlled; that is, the element colors could be displayed differently according to the degree of hazardous areas and structural deformation. e safety BIM model created by this module is passed to the data processing module for analysis. e last module is the function application module. It consists of two parts which are the data processing function and the user interface.
ere are four independent subfunctions in the data processing aspect: structural health monitoring, real-time positioning, wireless sensing, and model parameterization. e structural health monitoring is responsible for the real-time acquisition of data information on the deformation of the deep foundation pit's structure and correlates the obtained data information with the BIM safety information model. e real-time positioning is responsible for the real-time acquisition of position information pertaining to personnel, materials, and mechanical Advances in Civil Engineering equipment in the deep foundation pit construction site. is data is then shown in three-dimensional model. e wireless sensor is responsible for reading the tag information worn by on-site personnel and giving feedback information to the manager. e model parameterization setting is based on the real-time position information of the personnel machine and sets the parameter values of the relevant family members in the model, thereby realizing a visual display of the hazards, the hazardous area, and the monitoring point. In the UI of the web platform, it would realize both the BIM model and the real-time data display of hazards and hazardous areas, the position of personnel, and the automatic warning system related to structural deformation information.

Function Requirement Analysis for SMSoDFP.
Traditional construction safety management has many shortcomings, such as ignoring preventive management and lacking initiatives for personnel. Accident prevention and early warning systems are weak in the construction industry. Yuan [21] conducted statistical analysis of China's deep foundation pit accidents and found out that construction work problems which revolved around the violation of regulations, poor construction quality, poor emergency responses, construction organization problems, and poor supervision accounted for 69.46% of accidents recorded. e development of modern information technology provides a new way to change this poor situation. Based on BIM and other communication technologies, the proposed SMSoDFP should include the following functions. e first one is visualizing the potential hazardous areas in the BIM model based on safety rules. e safety rules are identified based on the design drawings, safety technical specifications, and hazards identified based on FTA. ey are applied in order to calculate the area where safety accidents often occur to determine the location and scope of potential hazardous. For example, collapses will not harm personnel outside the foundation pit but may cause those in the pit to be buried alive. erefore, the safety rule related to foundation pit collapse area should extend a certain distance inward and outward according to the shape around the foundation pit. As shown in Figure 5, x i and y i are the four corner coordinates of the deep foundation, x i ± n and y i ± n are the inward and outward corner coordinates of potential collapse hazardous areas, and n is the distance (1.2 meters) which is presently the construction specification in China. e second function is collecting safety information automatically.
is information includes the location, attributes, and other information required by the system and is automatically collected through monitoring equipment and positioning technology. is reduces inefficiency caused by manual data collection. e deep foundation pit construction site is a complex system that is constantly changing. In order to improve the efficiency of safety management, a series of information must be collected, including personnel, materials, and information on attributes and mechanical position. Data on deformation, displacement, and axial force changes during construction are also of great importance. Wireless sensing technology, positioning technology, and structural health monitoring equipment automation will be used.
e third is visualizing safety monitoring information. All safety information collected including personnel, materials, machinery, and monitoring point locations on construction site should be shown in the BIM safety information model. is will help managers to quickly, comprehensively, and intuitively understand and grasp the construction environment of the deep foundation pit and the safety status of staff. is helps to develop a realistic safety management plan for real-time monitored site conditions. e fourth is automatic monitoring and early warning. is requirement includes two aspects: (1) automatic monitoring and early warning of personnel approaching hazardous areas and their unsafe behaviors on the construction site; (2) automatic monitoring and early warning of dramatic changes in data information such as deep foundation pit deformation. It could rely on the color display of monitoring points in the BIM safety information model and the monitoring point family link monitoring data curve in the BIM model. At the same time, through the 4D function of the BIM technology, it could realize automatic monitoring and early warning of dramatic changes in data such as deep foundation pit deformation. In the event of an error, the safety manager can get a warning right way.

Information Need Analysis for SMSoDFP.
According to the function requirement analysis and the basic framework of SMSoDFP, there are four kinds of safety information which need to be collected: e first is the list of hazards for deep foundation pits, for instance, the edge of the pit, the wellhead, the tower  e second is the location information of personnel, materials, and machinery. e location information of personnel and construction machinery on construction site is a function based on time because this information changes over time. Real-time location information pertaining to personnel and machinery is imported into the BIM safety information model to automatically alert the objects when entering the hazardous area. e location information can be realized by real-time positioning equipment.
e third is the attribute information of the personnel on the construction site including name, gender, health status, operation type, violation situation, and construction area. Tags will be placed in each person's overalls or helmets to obtain the relevant attributes of the person by reading the tag information. Information on the wearing of protective equipment for personnel can be obtained through wireless sensing technology. e safety management system realizes individualized early warnings pertaining to the working conditions of the site personnel with different construction requirements in the hazardous area according to the jobs undertaken by the individual people. e fourth is the monitoring element position information and element deformation information of the deep foundation pit. is is important to ensure the safety of the deep foundation pit's structure and surrounding buildings. According to the characteristics of the project, combined with the existing safety monitoring specifications of the given pit, monitoring points are set in and around the engineering structure. e structural health monitoring equipment is used for real-time monitoring of the groundwater level, support, horizontal and vertical displacement of the foundation, support axial forces, and so on. e monitoring information is imported into the BIM safety information model, and the 4D function is used to realize real-time monitoring of displacement and deformation during deep foundation pit construction. By setting the function (IF) conditional statement of the family function in the BIM software, the color change of different monitoring points of the deep foundation pit  (x 4 + n, y 4 + n) (x 3 + n, y 3 + n) e on-site monitoring information can be mapped to the attributes in the IFC standard in the web platform (as shown in Figure 6). Data information in the SQL Serverbased deep foundation pit monitoring information database can be put together with the lightweight BIM model, which can be generated and uploaded from Revit model by Revit API in the IFC standard (Figure 7). e lightweight BIM model can then be used to monitor information changes in the deep foundation pit.

System Principle
ere are three major functional objectives in the construction Safety Management System of Deep Foundation Pits: visualization and automatic warnings of hazardous areas, personnel monitoring, and real-time monitoring of structural deformation. e implementation principle for the safety management system for the construction site is analyzed as follows.

Principle Analysis for Visualization of Hazardous Area.
In order to realize the automatic warning function pertaining to personnel entering hazardous areas, this study uses the relevant attributes of the deep foundation pit engineering BIM safety information model to integrate the hazards information of the deep foundation pit. Hazardous areas can be divided into two categories: hazards that can be identified at the design stage which have a relatively fixed position, such as a hole's edge. e other type of hazardous areas is generated during the construction process due to the operation of the construction machine. Table 1 provides a summary while Figure 8 shows the basic flow that identifies and creates Revit elements of hazardous area in different colors.

Principle for Personnel Position Monitoring.
Based on the visualization of hazards and hazardous areas in the BIM safety information model of deep foundation pits, it is necessary to use positioning technology to obtain the position information of the personnel in real time and to warn personnel entering the hazardous area automatically. ere are many common position-tracking technologies including GPS location, infrared positioning, RFID, WiFi, Bluetooth, Zigbee, and ultra-wideband (UWB) technologies. All these position-tracking technologies can be categorized into active (such as UWB) and passive types (such as WiFi, RFID, and Zigbee). ey are compared in terms of their characteristics in Table 2. Active type technologies use algorithm of AOA (angle of arrival), TDOA (time difference of arrival), and TOA (time of arrival). e active type has high positioning accuracy and is not easily disturbed, while the passive type is easily affected by obstacles such as water and metal due to the strength of the signal, and its position results exhibit more deviation and lower accuracy.
Given the complex environment of the construction site and the high accuracy requirements needed for safety management, the UWB position-tracking technology using the TDOA algorithm was chosen as the technology by which the location information of personnel in real time is collected in this SMSoDFP prototype test. During the test, one label was placed on the helmets of personnel to read their individual attribute information. An antenna was placed on the edge of each hazardous area of the deep foundation pit construction site according to the danger source, and when someone entered the area wearing a helmet with the label, the alarm sounded.
rough the specific API of Revit software, the real-time position of the person could be displayed in a 3D mode manner; this was important so that the manager could intuitively grasp the scene where the person wearing the helmet was and efficiently manage their safety while they were in the deep foundation pit construction site. e functional realization of the automatic warning required the use of the BIM safety information model, the real-time positioning system, and a wireless sensing system. By reading the tag information the real-time positioning system transmitted the data to the BIM model. rough the secondary development of BIM software and the API interface, the position and movement path of the person were displayed in real time in the BIM model.

Principle for Structural Deformation Monitoring and
Early Warning. In this study, the structural health monitoring equipment is used to monitor the axial force variations, the displacement changes, the groundwater levels, and the surrounding environment in the construction of deep foundation pits in real time. At the same time, BIM is used to realize the visualization of structural deformations and the automatic warning function during deep foundation pit construction.
According to the characteristics of deep foundation pit engineering, each component is treated as a kind of family in the process of model creation. It is necessary to complete the parametric family creation of models such as the earthwork model, the support model, and the trestle floor of deep foundation pit engineering. According to the positional relationship of each component plane in the design drawing, the component family is reasonably placed, and the BIM model of the deep foundation pit is initially formed. Construction machinery models (such as excavators, earth moving machines, tower cranes) and construction facility models (such as construction enclosures, material processing production areas) in the BIM model of deep foundation pits should be created. Reasonable site planning before the implementation of the project improves space utilization and reduces the occurrence of space conflicts and secondary handling events. At the same time, the hazards and the corresponding hazardous area are represented by different colors, and relevant precontrol measures are given to form a deep foundation pit structure monitoring model.
Deep foundation pit construction is a dynamic and complex process, and there are many projects to be monitored; therefore, there is a huge amount of data information. In order to improve safety management, it is necessary to ensure the real-time acquisition of various data information on the site and to realize the rapid processing of this data information. e overall framework of the deep foundation pit structure deformation monitoring and early warning system is divided into the sensing layer, the transport layer, the model layer, the data processing layer, the application layer, and the user layer (as shown in Figure 9).
In the process of structural deformation monitoring with regard to deep foundation pits, each time the BIM model acquires a monitoring value, it will compare it with its corresponding alarm value. Once the monitoring data exceeds the alarm value, it will sound an automatic early warning (as shown in Figure 10). e implementation principle of the automatic positioning of the monitoring points which are out of the alarm value is shown in Figure 11. Among them, the ID number automatically assigned to each primitive by Revit software in the BIM model is used to distinguish different primitives. When the monitoring data of a monitoring point exceeds its alarm value, the system automatically obtains its monitoring point ID and the corresponding sensor's ID. e software can then traverse the function of the model primitives to traverse the Element ID corresponding to all sensor primitives in the deep foundation pit model. By comparing the Sensor ID corresponding to the alarm value monitoring point with the Element ID of all the sensor elements in the model, the monitoring points with the same ID number are found and highlighted by the Element.ID method.

Case Description and Site Experiment Design.
A case study of a deep foundation pit project in Shanghai is presented to demonstrate the system. e China State Construction Engineering Corp (CSCEC) is the principal contractor of the project. e site layout is shown in Figure 12. e foundation pit is 20 m long and 13 m wide at the maximum. Its area is almost 240,000 square meters. e underground area has two floors, its foundation pit has been excavated to a depth of 10.05 m, and the deepest pit depth is 13.2 m.
rough the support of CSCEC, the contractor permitted the researchers to carry out a SMSoDFP prototype experiment and shared their foundation construction monitor data for comparison purposes. Table 3 shows the monitoring plan of the foundation contractor. All the data processing by the contractor was performed manually, and the monitoring result is not in real time. is case experiment took monitoring task of items 2 and 7 listed in Table 3 as the request by the contractor so that it would not disturb their construction. e contractor also agreed to make workers position test in specific safety area of its site. All the experiment equipment including deformation monitoring and UWB position tracking is shown in Table 4.
According to the SMSoDFP framework, the experiment collected information of both the UWB tag position and the monitoring elements' deformation. All collected data was imported automatically into a lightweight BIM model using the JavaScript API platform. After data processing based on the safety rule, the SMSoDFP prototype was verified. It has three functions: the visualization of hazardous areas, realtime monitoring of personnel, and real-time monitoring of structural deformation and automatic alarms. e effectiveness and feasibility of the system in performing such tasks were also demonstrated.

Visualization of Hazardous Area Test.
e color simulation module includes two subfunction modules: the hierarchical display of the hazardous area and the color simulation of the structural deformation point. e classification of the hazardous area comprehensively identified the existing hazards in the BIM model based on the identified list of hazards in the construction site. It automatically arranged safety protection facilities at locations such as the edge of the hole to reduce the occurrence of accidents. e color deformation function of the structural deformation point was based on the monitoring information obtained by the structural deformation monitoring equipment during the construction of the deep foundation pit.
is helped the construction site managers to quickly, comprehensively, and intuitively understand the on-site environmental status of the deep foundation pit and formulate a feasible safety management plan for the real-time monitored site conditions. Hazardous area is displayed in different colors according to the hazardous level in Revit (as shown in Figure 13). After being uploaded to the web platform, the lightweight BIM model is shown in Figure 14. e red color represents a Class I hazardous area (set within 0.3 m from the hazards), indicating that there is a high probability of an accident. Yellow indicates a Class II hazardous area (set within 0.5 m from the hazards and indicating a greater likelihood of an accident). Green represents a Class III hazardous area (set to the edge of the hazardous area and indicating the presence of a hazardous area). e color simulation of the structural deformation point was based on the real-time structural monitoring data of the

Personnel Position Monitoring
Test. e experiment installed wireless sensors in the northwest corner, southwest corner, and southeast corner of the foundation pit, and all the collected data was transmitted to the computer. is formed a complete staff positioning network. e range  Foundation pit support e inspection is qualified, and the lack of the latest safety inspection record is regarded as a hazardous area Scaffold e inspection is qualified, and the lack of the latest safety inspection record is regarded as a hazardous area

Falling from a height
Manual digging pile hole 1 m from the edge of the orifice e edge of the hole 0.6 m from the edge of the hole Scaffolding formwork Coverage of formwork collapse Tower crane use e range of the circle is centred on the hanging object, and the instantaneous reaction distance of the person is the radius

Object strike
Support erection e inspection is qualified, and the lack of the latest safety inspection record is regarded as a hazardous area Scaffolding e inspection is qualified, and the lack of the latest safety inspection record is regarded as a hazardous area Tower crane use Plane projection area Tower crane Detecting tower crane speed, with overspeed being considered unsafe area Formwork Demolishing area

Mechanical injury
Crane Plane projection area Concrete pumps Work area and moving route Other moving equipment or machine Work area and moving route

Adjacent environment damage
Crane e maximum range of the circle centred on the hanging object Support system Retaining structure or other support element covered by the triangle (as shown in Figure 15) is the range in which the entire network could collect tag data. By comparing the position of the worker tracked by the wireless sensor with their actual position, it was found that the system could monitor the real-time position data of the worker. e position of the label tracked on the computer was compared with the actual position of the label (as shown in Figure 16), where the green line indicates the true motion path and the broken line indicates the motion path tracked by the system. It can be seen that, due to the need to measure the entry of personnel into the hazardous area, an experiment was conducted in which the person gradually approached the base point (as shown in Figure 17). e upper right corner indicates the time when the person was close to the base point, and the lower left corner indicates the distance (in millimeters) of the person from the base point. It was found through this experiment that the position of the tag was not easily tracked when it is in a particularly concealed place such as a stairway. ere was, therefore, a need to place more receivers in the monitoring area to ensure the accurate tracking of the tag. rough this test, it was shown that the UWB system can track the position of the tags. As per the UWB provider (brand: Decawave) instructions, the level of accuracy is related to both the movement speed and the position of the tag. e slower the movement speed of the tag, the more accurate the positioning. When the location of the tag is lost, there is a need to place more anchors in the monitoring area   to ensure monitoring accuracy. Finally, the data collected by the system will drive the movement of the personnel in the model, visualize the movement of the personnel, and monitor the movement of the construction personnel.

Structural Deformation Monitoring and Early Warning
Test. e real-time display function of the structural deformation monitoring data is realized by reading the data in the monitoring data subtable of the deep foundation pit engineering SQL Server database. At the same time, the data is also displayed in the drawing area in the form of data curves. e manager can visually grasp the monitoring status of the deep foundation pit by viewing the data curve. In the experiment, the data collected by both displacement and clinometer is not significant  changes for the reason of short time or good construction quality. e following is the analysis of the data collected by surface strain gauge. In this project, the design strength of the deep foundation pit supporting concrete was C35, and the section size was 800 mm * 1000 mm. According to the requirements of the code, the warning value of the foundation pit support structure was 70%-80% of the design value. e calculated alarm value was 19600 kN-22100 kN. erefore, this article set the warning value to 20000 kN. When the monitoring value exceeds the warning value, the manager is reminded in the form of a pop-up warning. e real-time monitoring data curve for deep foundation pit deformation was controlled by the MSChart plug-in. e realization of the automatic early warning function includes two parts: the pop-up window warning and the automatic positioning for the alarm value. When the monitoring data of a certain monitoring point exceeds the alarm value, the system will pop up prompt tags window, and it will show the history monitoring data when doubleclicking the prompt tags (as shown in Figure 18). is system also could connect the monitoring camera in construction site. e camera video can pop up when clicking the camera element in BIM model (as shown in Figure 19). Besides, it could draw the simulation of deformation field based on the collected data of giving deformation monitoring point. Figure 20 shows the deformation simulation according to the value of displacement meters placed in construction site.    14 Advances in Civil Engineering

Discussion and Conclusion
In this research, a system framework prototype was proposed for the safety management of deep foundation pits based on BIM and IoT. is prototype system has proven to be feasible and effective within the limits set by the experiment.
e contractor who supported this experiment made the following comments and suggestions: Firstly, the proposed system framework has great potential value for on-site safety management. It is the main controlling factor for on-site safety management of deep foundation pits and strengthens on-site realtime monitoring at the construction site, rationally arranging safety protection measures, strictly monitoring personnel positions to avoid entering hazardous areas, and rationally carrying out construction organization design. Secondly, BIM is one of the most important technologies for the modernization of the construction industry. BIM has also been vigorously promoted by the Chinese government in recent years. e proposed SMSoDFP prototype gives more application ideas for construction management, especially with regard to visualization hazardous area and the combination of that data with other information technologies such as position tracking and deformation monitoring.
irdly, the SMSoDFP has many merits for improving contractor capabilities with regard to construction safety management. For example, the hazard identification FTA could help with safety education and  training. e visualization of hazardous areas could also be better for the quality of construction planning and the effective disclosure of safety matters. e best thing that arose from the experiment was that the system can show monitoring sensor location and collected data in real time in the BIM model. Even though the early warning depends on the threshold values, the history curve could be very helpful in understanding the status of construction and as a means by which changes in next phase are predicted.
On the other hand, the contractor also gave many suggestions with regard to areas in which the SMSoDFP still needed to improve its effectiveness if it was going to be a practical application within constructions sites. For example, while it was good that position tracking by the UWB could provide real-time 3D coordinates, there remained the case that it was easy to lose the tag signal in the complex environment. Although this problem could be relieved by increasing anchor quantity, this is an obstacle to its application. For structural deformation monitoring, the contractor hoped that the system could provide more kinds of commercial graphics other than only showing the data via the curve.
In general, the prototype of SMSoDFP could be helpful in hazardous area identification in deep foundation pits sites, as it provides rich on-site information, timely updates, feedback, storage, and processing. e visualization of hazardous areas can help on-site technicians to make technical disclosures, which helps managers to understand situations in a convenient manner. e system realizes the real-time positioning of construction site personnel and real-time monitoring of deep foundation pit structure and produces automatic alarms.
is makes it easy for field managers to react when they have problems. When a danger is about to occur, the reaction time of the personnel involved can be reduced, thereby lowering the accident rate. is can significantly improve the level of safety management. In order to improve the level of safety management within deep foundation pit construction, a framework of SMSoDFP was established based on combination of BIM and IoT. rough carrying out site experiment, the three functions of visualization, personnel monitoring, and structural deformation monitoring were tested and found to be feasible and effective within the limits of the experiment. In future, research that includes a detailed hazardous database should be carried out-building on that contained herein-so that big data and artificial intelligence (AI) could be incorporated into broader considerations of construction safety. At the same time, further study combining BIM and other information communication technologies, such as image recognition, UAV-assisted aerial photogrammetry for site work, big data technology, and IoT supported by 6G wireless network, needs to be undertaken in order to improve construction safety at a management level.

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.

Disclosure
Wenhan Fan, Jianliang Zhou, and Jianming Zhou are joint first authors.

Conflicts of Interest
e authors declare no conflicts of interest.

Authors' Contributions
Wenhan Fan, Jianliang Zhou, and Jianming Zhou contributed equally to this work.