Research on Permanent Magnet-Type Super-Low-Frequency Mechanical Antenna Communication

In the super-low-frequency (30 ∼ 300Hz) band communication, the traditional antenna covers a large area and has low radiation efficiency. *e excitation of electromagnetic waves by the mechanical motion of permanent magnets enables miniaturized technology for super-low-frequency communication. For this miniaturization technique, this paper proposes a super-lowfrequency communication architecture framework. *eoretical analysis and experimental verification of each unit module in the structural framework are carried out to achieve high-quality communication. For the radiation unit, permanent magnet parameters and communication distances are introduced to establish a rotating permanent magnet radiation power analysis model and to study the radiation characteristics of rotating permanent magnets. For the receiver unit, a sensitivity normalization characterization method based on the ratio of the coil thermal noise voltage to the induced voltage is proposed. Based on the sensitivity analysis model, a square coil was developed that meets the communication requirements of a mechanical antenna and an experimental platform was built. Experiments are conducted on the factors affecting radiated power and coil sensitivity, and 2FSK signal modulation communication experiments are conducted to verify the feasibility of the communication structure framework. *e volume of the mechanical antenna permanent magnets in the experiment is all below 10 cm, and the operating frequency is continuously adjustable from 0 to 250Hz. *e experimental results show that the near-field radiated power of a rotating permanent magnet is proportional to square of the volume of the rotating permanent magnet; the sensitivity of the coil is proportional to the number of turns and the area of the coil. By controlling the speed in real time, you can control the frequency of the signal and modulate it.


Introduction
Super-low-frequency (SLF) electromagnetic waves (30 Hz∼300 Hz) have excellent seawater penetration and diffraction capabilities, low path loss in water and soil, and strong anti-interference ability. erefore, super-low-frequency electromagnetic waves are used in the submarine command, mine emergency, earthquake prediction, and penetration. Terrestrial communications and other fields have colossal application potential [1]. In recent years, it has received widespread attention and is also an effective means to realize submarine communication [2].
In practical applications, the existing transmitting antennas are all electrically small antennas (ESAs), which rely on the oscillating current in the conductor to excite electromagnetic waves. ESA is an antenna whose size is small compared to the wavelength of electromagnetic waves in the frequency band in which it works, and generally its size satisfies (l/λ) ≤ (1/2π) [3,4]. Nowadays, there are mainly three kinds of common electric small antennas, which are electric oscillator-type antenna, magnetic oscillator-type antenna and combination-type antenna. ey are achieved through the integrated use of composite structural materials, multipoint feeds, coaxial chokes, and other technologies [5,6]. e bandwidth and gain of the antenna can be increased by these techniques.
Due to the length of the electric small antenna is much smaller than the working wavelength, its equivalent resistance is often very small, and its reactance part dominates in its impedance, making the change of frequency has a great impact on the antenna input impedance. Chu et al. [7,8] gave a theoretical limit of ESA based on the radiation quality factor Q rad : the smaller the antenna size, the larger the Q rad , and the lower the antenna radiation power and radiation efficiency under certain radiation power conditions. Due to the abovementioned theoretical limitations, the radiation performance of ESA is directly limited by the antenna size, so that existing low-frequency electromagnetic transmission systems have problems such as bulky antennas, complex equipment, low radiation efficiency, massive transmission power, and energy consumption.
To address these issues, in February 2016, the Defense Advanced Research Projects Agency (DARPA) first proposed the concept and project idea of a "mechanical antenna" (MA) to replace the traditional ESA that relies on oscillating current excitation [9,10]. e MA excites and emits super-low-frequency electromagnetic waves by driving an electric dipole or magnetic dipole. MA has opened up a new possible way for the radiation of super-low-frequency electromagnetic waves [11,12].
Motivated by related projects, several universities and research institutes at home and abroad have conducted preliminary research and exploration of mechanical antennas. Under the same conditions, electrets have higher radiation efficiency than permanent magnets. However, there are technical difficulties in generating a stable, continuous, and high-density static charge on the electret. erefore, many researchers have chosen rotating permanent magnets as the mechanical antenna transmitting module. e study [13] presented a patent describing a novel antenna for generating low-frequency electromagnetic waves from rotating permanent magnets. In 2017, Madanayake proposed an underwater positioning system consisting of at least three mechanical antennas as reference points and a multidimensional vector magnetometer on the uncrewed underwater vehicle (UUV) as a receiver. Madanayake et al. derived the formula for the magnetic field of a mechanically rotating dipole by assuming that the magnetic field generated by a time-varying dipole has the same spatial distribution as that generated by a static dipole [14] but did not study it experimentally. In 2017, Huang concluded that the spin magnet system is not subject to the Chu Harrington limit in ULF communication and obtained the electromagnetic field formula for the far field [15]. However, the spin permanent magnet, as an ULF mechanical antenna radiation unit with an extremely long wavelength, is more relevant for the near field. In 2018, Gong et al. derived the formula for the electromagnetic field of a rotating permanent magnet in space [16]. Chen et al. discussed the radiation of electric dipoles for this particular motion of uniform rotation [17], which were well deduced from their theory, but not further studied in conjunction with practical situations or simulations. e "mechanical antenna" project consists of two technical fields (TA1 and TA2), which are divided into three phases (Phase 1∼Phase 3) to reduce the difficulty of realization. e time-varying magnetic field strength during steady-state operation of the three phases of TA1 is 1∼100 fT@1 km, while the magnetic field strength signal of the fT level is very weak. Highly sensitive magnetic sensors are required for reception. In the field of magnetic sensor technology today, there are mainly magnetic induction coils, optical pump magnetometers, proton (nucleon) spin-in magnetometers, and superconducting quantum interference magnetometers with resolutions up to the pT level [18,19]. Magnetic induction coils are used in mechanical antenna receiving units because of their simple structure, low power consumption, stable performance, and high resolution [20]. Domestic and international scholars have done a lot of beneficial research for the establishment of an accurate mathematical model for the transmission characteristic analysis of magnetic induction coils in the super-low-frequency domain. ey mainly focus on the accurate calculation of the equivalent electrical characteristics parameters (equivalent resistance R, equivalent inductance L, and equivalent capacitance C), the signal-to-noise ratio of the coil, and its feasibility in the low-frequency field.
In order to accurately calculate the equivalent inductance, resistance, and capacitance of the coil, many scholars have done a lot of beneficial research. Zhang established the transfer function of the coil based on the theoretical model of the equivalent circuit of the coil, improved the computational model of the equivalent capacitance, predicted the characteristics of the coil such as resonant frequency, transfer function, and sensitivity, and verified the accuracy of the model through experiments [21], but the study of the parameters of the equivalent electrical characteristics mainly focused on the high-frequency spectral band and did not discuss in detail in the super-low-frequency domain. For the study of methods to improve the signal-to-noise ratio of coils, Slawomir Tumanski analyzed the principle and characteristics of different winding methods of coils and proposed a coil design and parameter optimization method that takes into account both signal-to-noise ratio and sensitivity [22]. To address the feasibility of coils in the lowfrequency domain, Burch et al. designed a receiver consisting of a three-axis orthogonal coil and a 24 bit acoustic frequency data recording card, and analyzed the positioning effect of the receiver both theoretically and experimentally, demonstrating that it is feasible and practical at frequencies below 500 Hz and at distances greater than 100 m [23].
In this work, based on a new signal generation and radio transmission mechanism, a mechanical antenna structure is proposed, which mainly includes a signal transmitting module and a signal receiving module. Based on the signal transmitting module, an analytical model of the rotating permanent magnet radiation power is established. Based on the signal receiving module, a coil is selected as a magnetic sensor to receive the signal based on the radiation intensity of the radiated field source. For coil magnetic sensors, a sensitivity normalized characterization method based on the ratio of the coil-induced electric potential force to the thermal noise voltage is proposed. In this paper, a prototype SLF communication principle is developed based on the coil sensitivity model and radiated power model. e correctness of the analytical model and the feasibility of 2FSK communication are verified by conducting experiments with the developed prototype.

Mechanical Antenna Communication
Model System 2.1. Mechanical Antenna Structure. Super-low-frequency mechanical antennas generate signals through the mechanical vibration of permanent magnets or electrets to transmit superlow-frequency radio waves. e electrets or permanent magnets are the core radiating components of the mechanical antenna. Electret and permanent magnet can be equivalent to electric dipole and magnetic dipole, respectively. According to Coulombʼs law, an electret is equivalent to a collection of charges, which can be equated to an energized coil; a permanent magnet is equivalent to a collection of magnetic dipoles, which can be equated to two charged planes. e mechanical antenna field source model is selected by comparing the ability of the two equivalent models to produce magnetic field strengths. e model parameters of permanent magnet and energized coil are shown in Table 1.
e model of permanent magnet and the energized coil are shown in Figure 1.
e magnetization intensity of permanent magnet is M � 1.1 × 10 6 A/m, and the calculation formula of magnetic field intensity H is where N is the number of turns of the excitation coil; I is the excitation current; and L is the effective magnetic circuit length of the excitation coil. According to formula (1), an excitation coil with a wire diameter of 12AWG and a number of turns of 330 applying an excitation current of 100 A can radiate a magnetic field strength of H � 1.1 × 10 6 A/m. However, the 12AWG coil can withstand the maximum current of 14.9 A. erefore, eight energized coils of the same size would be required to apply a current of 12.5 A to radiate a magnetic field strength of H � 1.1 × 10 6 A/m. erefore, in this paper, permanent magnets are chosen as the radiating unit of the super-lowfrequency mechanical antenna.
To better control the drive motor and receive communication signals, a mechanical antenna structure is proposed as shown in Figure 2, which mainly includes a signal transmitting module and a signal receiving module. e signal transmitting module is mainly composed of radiation field source (permanent magnet), drive motor, power converter, controller, and signal generator. e signal generator sends the signals required for communication to the inverter and power converter. e inverter outputs signals to control the speed of the drive motor.
e drive motor drives the permanent magnet to generate a time-varying magnetic field, which radiates electromagnetic waves. e signal receiving module is mainly composed of a magnetic sensor and a preamplifier. e magnetic sensor receives the time-varying magnetic field signal and processes the signal through the preamplifier to obtain the communication signal and complete the mechanical antenna communication.

Information Loading Module and Its Speed Control
Method. Unlike high-frequency carrier systems, super-low-frequency carrier communication systems typically have a narrower bandwidth but are less susceptible to outside interference. As a super-low-frequency communication navigation transmitter system, the modulation methods used are mainly divided into amplitude modulation, frequency modulation, and phase modulation. However, due to the extremely long operating wavelength of SLF communication systems, which usually operate in non-far-field regions, amplitude modulation information is complex and not easily demodulated. Phase modulation requires precise control of the motorʼs rotational attitude at different times.
is is difficult to achieve for super-high-speed motors running at 10,000 rpm or more. erefore, frequency modulation is used for SLF mechanical antenna communication modulation.
Frequency modulation currently uses constant envelope modulation methods such as FSK and MSK. Mechanical antennas load the information by changing the state of the rotational motion of the field source. erefore, the frequency parameters need to be mapped to the rotational state of the field source to generate the input parameters of the rotating servo system.
In order to realize the information loading of FSK, this paper proposes an information loading method based on the field source rotation speed n control, which maps the frequency modulation to the control of the average rotation speed n. Taking 2FSK as an example, Figure 3 is based on n control and shows a schematic diagram of generating corresponding control signals based on code data.

Energy Conversion of Mechanical Antenna.
e rotation servo system of the mechanical antenna converts the input electric power P in into the rotating torque of the field source, the electromagnetic energy radiated by the field source, and the useless power loss. Loss of useless power includes resistive loss, mechanical friction loss, and dielectric loss. Resistive loss includes motor copper loss, controller and power converter loss, etc. Mechanical friction loss includes  overcoming friction caused by bearings, wind resistance, etc. Dielectric loss includes two parts, namely: (1) eddy current and hysteresis loss of the motor core; (2) near-field energy storage where a rotating field source generates a timevarying magnetic field. erefore, the mechanical power output by the permanent magnet synchronous motor can be expressed as where P R is resistive loss; p Ω is mechanical friction loss; P m 1 is eddy current and hysteresis loss of the motor core; P m 2 is the dielectric loss of the time-varying electromagnetic field generated by the rotation of the field source; and P rad is the radiated power.
According to the above energy conversion relationship, the radiation efficiency of the mechanical antenna can be defined as

Research on Magnetic Field Distribution Characteristics and Magnetic Reception Technology
At present, magnetic reception technology is basically used for super-low-frequency electromagnetic communication. e development of a prototype mechanical antenna to meet the communication needs is the key to this study. In this study, the radiation intensity of rotating permanent magnets and the reception performance of magnetic sensors directly affect the communication distance. erefore, it is crucial to study the time-varying magnetic field characteristics radiated by rotating permanent magnets as well as the magnetic sensor sensitivity. A theoretical reference is provided for the development of a high-performance mechanical antenna communication model.

Magnetic Field Distribution and Attenuation
Characteristics of Rotating Permanent Magnets

Physical Model of Rotating Permanent
Magnet. e physical model of the rotating permanent magnet is shown in Figure 4, assuming that the dimensions of the permanent magnet are l, w, and h. In an infinite uniform medium, the permanent magnet takes the geometric center as the origin and moves at a constant rotation around the z-axis with   e angle between the direction of magnetization and the y-axis where the rotation begins is ϕ 0 .
According to the ampere current model, the uniformly magnetized permanent magnet is equivalent to the ampere current on its surface. e direction of the current is shown in the direction of the arrow in Figure 4, and the equivalent surface current density is given: where M is the equivalent surface current density constant and n is the unit vector of the magnetization direction of the permanent magnet itself. In Figure 4, the surface currents are distributed on rectangular polar surfaces parallel to the direction of magnetization (the four faces labeled 1, 2, 3, and 4 in Figure 4), and there are no surface currents on the other faces.

Magnetic Field Distribution and Attenuation
Characteristics.
e equivalent current of a rotating permanent magnet is distributed only at its surface, and the retarded potential A (r, t) is as follows: where μ is the magnetic permeability of the transmission medium; R is the distance between field point r and source point r9; c is the speed of light; Ω(t) is the integral domain (four sides of 1, 2, 3, and 4 marked in Figure 4); and J (r9, For the permanent magnets shown in Figure 4, the retarded potential A (r, t) can be deduced as follows: where B 0 � μM and V are the remanence and volume of the permanent magnet, respectively; k � ω/c is wave number. Based on the retarded potential A (r, t) and the ampere current model, the equations of magnetic induction intensity B (r, t) and the electric field E (r, t) of rotating permanent magnet at r are obtained: where θ is the polar pole angle, which is the angle between the connecting direction of the test point and the origin and the positive direction of the z-axis; ϕ is the azimuthal angle, which is the angle between the connection direction of the test point and the origin and the positive x-axis direction; η � ��� μ/ε is the wave impedance of the transmission medium, where ε is the dielectric constant of the medium.
In the near field, kr ⟶ 0. From equations (7) and (8), the magnetic and electric field strengths in the near-field region can be expressed as follows: International Journal of Antennas and Propagation In the near field, the magnetic field strength B near produced by the rotating permanent magnet has three components simultaneously r, θ, and φ. e magnitude of the magnetic field strength is proportional to the remanence of the permanent magnet and decays in the third power of the communication distance r. e phase difference between the magnetic field intensity and the electric field intensity is π/2 in the near region, so the near-area field is a quasi-static field.
In the far field, kr ≫ 1. From equations (7) and (8), the magnetic sand electric field strengths in the far-field region can be expressed as follows: In the far field, the magnetic field strength B far produced by the rotating permanent magnet has two components simultaneously θ and φ. In the far-field region, both the magnetic and electric field strength amplitudes decay with 1/ r and are in phase. us, the far field is a spherical wave, with energy radiating out completely.
For a lossless medium, the radiation energy flow S of a rotating permanent magnet can be expressed as follows: In terms of the relationship between radiated power and energy flow density, the radiated power of a rotating permanent magnet can be expressed as follows: From equation (13), the radiated power of the timevarying magnetic field generated by a rotating permanent magnet in the near field is proportional to the square of the residual magnetism and volume of the permanent magnet, and inversely proportional to the quartic of the communication distance. From equation (14), the radiated power of the time-varying magnetic field generated by the rotating permanent magnet in the far field is proportional to the square of the residual magnetism of the permanent magnet and the volume of the permanent magnet and is independent of the communication distance. (9), a permanent magnet of material NdFeB, grade N52, remanence of 1.38 T, and size ϕ100 × 200 mm produces a timevarying magnetic field strength of 125 fT at 1 km by rotational motion. erefore, the resolution of the magnetic sensor in the mechanical antenna communication receiving unit needs to be 125 fT/ �� � Hz √ and the detectable magnetic field range needs to be less than 125 fT.

Magnetic Sensor Model.
Today, the detectable range and resolution of standard magnetic sensors are shown in Table 2. From Table 2, it can be seen that the optimal magnetic sensors for the super-low-frequency time-varying magnetic field measurements are superconducting quantum interferometers and coils. Because of its simple structure, convenient construction, and stable performance, the coil has low requirements for SLF communication environment. It is convenient to build antenna communication structure. erefore, in this study, the coil is selected as the SLF mechanical antenna signal receiving module.
According to the law of electromagnetic induction, the coil will generate an induced electric potential of the same frequency in the time-varying magnetic field of the transmitting antenna. e coil acts as a magnetic sensor, and its most sensitive direction is the normal direction. erefore, the mechanical antenna communication system uses a threeaxis orthogonal square coil for signal reception. e timevarying magnetic field in any direction in space is determined by detecting the time-varying magnetic field in the X, Y, and Z directions with a three-axis orthogonal coil.

Normalized Sensitivity Model of Magnetic Sensor
Sensitivity. e super-low-frequency mechanical antenna adopts a three-axis orthogonal square coil magnetic signal receiving technology. e ability to develop a coil that meets the communication requirements is the key to this research. In a time-varying magnetic field, the induced voltage of the coil represents the average value of the detection signal, and the thermal noise voltage represents the minimum value of the detection signal. erefore, in this study, the coil sensitivity was characterized by the equivalent ratio of antenna thermal noise voltage and time-varying magnetic field-induced voltage. e sensitivity normalization model is developed to provide the theoretical basis for the design of high-performance magnetic sensor coils.
(1) Time-Varying Magnetic Field-Induced Voltage. According to the principle of equivalent distribution of the electrical characteristic parameters of the coil, the equivalent resonance circuit model of the air-core coil is shown in Figure 5. In the figure, U is the output-induced voltage of the coil; R is the equivalent resistance of the coil, that is, the resistance of the wires that constitute the coil; L is the equivalent inductance of the induction coil, which represents the inherent characteristics of the coil itself and has nothing to do with the current; C is the equivalent capacitance of the coil, mainly the capacitance existing between the turns of the coil. e time-varying magnetic field generated by a rotating permanent magnet is a sinusoidal signal whose output-induced voltage can be expressed as follows: where N is the number of turns of the coil; A is the area of the single-turn coil; ω is the rotation angular velocity of the permanent magnet; f is the operating frequency of the rotating permanent magnet; θ is the angle between the incident direction of the time-varying magnetic field and the axis of the coil. When the coil axis is horizontal, θ only indicates the position of the receiver coil, and its value is 0°. erefore, the cos (θ) in the formula (15) can be ignored. It can be seen from equation (15) that the number of coil turns N, the coil area A, and the working frequency f are all proportional to the induction electromotive force of the coil.
(2) ermal Noise Voltage. In the SLF domain, the wavelength (10 3 km∼10 4 km) of the electromagnetic wave is much larger than the width of the coil. erefore, the winding capacitance and surface skin effect of the coil can be ignored. e magnetic induction coil is equivalent to an inductive device consisting of a resistor and an inductor. Its equivalent circuit is shown in Figure 6. It consists of equivalent resistance R and equivalent inductance L.
According to the definition of resistance, the coil resistance can be expressed as follows: where ρ is coil resistivity; d is the wire diameter; N is the number of turns of the coil; and A is the cross-sectional area of the coil.
According to Biot-Savart Law, the inductance L of coils of different shapes can be expressed as follows: where c 1 and c 2 are coil shape coefficients, and coil coefficients of different shapes are shown in Table 3.
In the super-low-frequency domain, the wavelength of electromagnetic waves (4000 km at 75 Hz) is much larger than the edge length of the coil, so the radiation resistance of the coil is negligible compared to the coil resistance. erefore, the minimum value of the detection signal is limited by the thermal noise generated by the coil resistance R a . e RMS (root mean square) thermal noise voltage V Nt across the coil resistance R a can be expressed as where K is Boltzmann constant, K � 1.38 × 10 − 23 ws/K; T is the absolute temperature of the conductor (K); Δf is the noise bandwidth of the measurement system. e unit to the RMS thermal noise voltage is V · �� � Hz √ . It can be seen from formula (18) that the main influencing factors of the coil thermal noise voltage are the coil resistance R and the noise bandwidth Δf.

(3) Sensitivity of Magnetic Induction Coil.
e magnetic induction coil sensitivity S is defined as the field equivalent of the noise density, which is the equivalent ratio of the coilinduced electromotive force to the thermal noise voltage. In other words, the magnetic induction coil sensitivity is the magnetic field equivalent of the thermal noise in a 1 Hz bandwidth. Let the RMS thermal noise voltage of the 1 Hz bandwidth be equal to the output voltage to obtain the magnetic field intensity of the magnetic induction coil measurement signal. erefore, the sensitivity of a magnetic induction coil can be expressed as It can be seen from equation (19) that the sensitivity of the receiving antenna increases with increasing frequency. However, frequency is an external factor that affects the sensitivity of the receiving antenna. In mechanical antenna communication, the presence of bandwidth can change the sensitivity of the same structural coil. In order to study the factors influencing the variation of coil sensitivity in the  International Journal of Antennas and Propagation same structure during communication, the coil sensitivity calculations were normalized with a normalization factor of 1/f. erefore, the normalized formula for coil sensitivity can be organized into equation (20), which has units of T/ �� � Hz √ : . (20) From equations (16) and (20), the relationship between the geometric parameters and sensitivity of the magnetic induction coil can be expressed as follows: From equation (21), the factors that affect the sensitivity of the magnetic induction coil are the parameters of the coil itself. ere is a correlation between coil sensitivity S and its turns N, cross-sectional area A, and wire diameter d.
erefore, the coil sensitivity can be improved by increasing the number of turns, the cross-sectional area, and the wire diameter within the allowable coil size. erefore, the design accuracy of the geometric parameters of the magnetic induction coil is directly related to the accuracy of the sensitivity of the coil model.

Simulation Analysis of Radiation Field Attenuation Characteristics
Super-low-frequency mechanical antennas are long-distance communication devices whose communication media are mainly air, soil, and seawater. In order to better study its propagation characteristics, this paper uses the simulation software Ansoft to simulate the attenuation characteristics of the radiation field in different media. e simulation model is shown in Figure 7. e parameters related to the transmission medium and the permanent magnet in the simulation model are shown in Table 4. e simulation results are processed to obtain the radiation intensity at the corresponding detection points in different propagation media. e simulation results are processed to derive the distance-dependent curves of the magnetic induction intensity of rotating permanent magnets in the three propagating media, as shown in Figure 8. e propagation characteristic curve was fitted using Matlab for the transmission medium of air, and the results are shown in Figure 8.
It can be seen from Figure 8 that the radiation signal of the rotating permanent magnet has the least propagation loss in air, followed by soil, and the greatest propagation loss in seawater. In air and soil, the time-varying magnetic field generated by rotating permanent magnets had essentially the same trend. It is assumed that the minimum magnetic induction strength that can be detected by the receiving antenna is 1 nT. When the rotating permanent magnet operates at a frequency of 75 Hz, the maximum communication distance is 147.5 m in air, 145 m in soil, and 73 m in seawater. In fact, some SLF receivers can detect signals with a magnetic susceptibility of less than 1 nT. erefore, the communication distance will be longer. From the fitted curve of the propagation medium being air, it is known that the magnetic susceptibility is inversely proportional to the cube of the propagation distance. It is proved that the mathematical model of the rotating permanent magnet is correct.

Principle Prototype Development and Experimental
Based on the mechanical antenna communication structure and magnetic induction coil, the principle prototype shown in Figure 9 was constructed. e principle prototype is composed of three main parts: the radiation unit, the propagation path, and the receiving unit. e mechanical antenna radiation unit transmits signals through a signal generator. e frequency converter receives signals from the signal generator to control the motor speed. e motor drives a permanent magnet that generates a time-varying magnetic field, which radiates electromagnetic waves. Electromagnetic waves propagate in the air or on the ground and are received by magnetic sensors. e mechanical antenna receiving unit receives the signal via a three-axis orthogonal coil. e coil receives the signal and transmits it to an oscilloscope, which converts the analog signal into a digital signal. en, the digital signal is sent to the upper computer, and the upper computer performs Fourier transform on the signal to obtain the transmission signal information of the radiation unit, thereby completing the communication.
Based on the mechanical antenna communication principle prototype, experiments are conducted on the rotating permanent magnet radiation power, coil sensitivity, and 2FSK communication. A three-axis orthogonal square coil with an impedance of 1 Ω-1 mH is developed as the mechanical antenna receiving unit. e driving motor speed is 0∼15,000 r/min, corresponding to the emitted electromagnetic wave is 0∼250 Hz and continuously adjustable.

Radiation Power Influence Experiment.
According to the communication principle model diagram of the mechanical antenna shown in Figure 9 and radiation power model (13), the super-low-frequency mechanical antenna experimental platform shown in Figure 10 is built to study the influence of the permanent magnet volume on the radiation power. e     International Journal of Antennas and Propagation driving motor speed is 3600 rad/min, and the corresponding electromagnetic wave radiation frequency is 60 Hz. e permanent magnet adopts 4 types of radially magnetized permanent magnets as shown in Table 5, and their timevarying magnetic field signals are measured, respectively. In this work, the time-varying magnetic field signals of 4 kinds of permanent magnets were analyzed to calculate their timevarying magnetic field magnetic induction intensity values, and their radiant power was calculated by combining equations (7) and (13). e permanent magnet model, timevarying magnetic field magnetic induction intensity, and radiation power are shown in Table 5. e radiant power generated by the rotating permanent magnet is fitted to the data with equation (13) using MATLAB to obtain the experimental fitting curve and experimental points as shown in Figure 11.
In this experiment, the four permanent magnets have the same material and magnetization capacity. In Figure 11, the experimental fitting curve is obtained by fitting the experimental points. e fitting curve equation is a unary quadratic function whose intercept is not zero. e relative error between the equation coefficient of the fitted curve and the theoretical value is 16.4%. e reason for the nonzero intercept of the equation is the error between the actual volume of the permanent magnet and the experimentally measured volume. e equation of the fitted curve is approximately the same as the radiated power resolution model, which shows that the radiated power of a rotating permanent magnet is proportional to the square of its volume. erefore, its theoretical analytical model is reliable. Some factors that affect the communication distance of the mechanical antenna are as follows: the volume of the permanent magnet and the remanence of the permanent magnet. Figure 12, this paper builds a prototype coil sensitivity experiment based on a prototype mechanical antenna model. In Figure 12, a is the signal generator and frequency converter, and b is the motor and permanent magnet, which constitute the radiation unit; c is a three-axis orthogonal coil, and d is an oscilloscope, which constitute a receiving unit. In the radiation unit, a time-varying magnetic field is generated by a motor-driven permanent magnet, which forms electromagnetic waves. e frequency of electromagnetic waves is 75 Hz. e communication distance is set as 6 m. Radiation unit selected axially magnetized permanent magnet, which the material is N48, the remanence is 1.1 T, and the size is 90 × ϕ8 mm. According to equation (6), the theoretical value of time-varying magnetic field strength generated at 6 m on the rotating permanent magnet is 1.03μT. e receiving unit adopts copper wire with diameter of 1 mm.

Coil Sensitivity Influence Experiment. As shown in
In this paper, the effects of coil turns and cross-sectional area on sensitivity are analyzed by the single-factor method. Make the coil impedance 1Ω mH and design coils 1, 2, and 3 according to equations (16) and (17). To study the effect of coil cross-sectional area on coil sensitivity, design coils 1 and 3, and change only the coil cross-sectional area A, while keeping other parameters unchanged. To study the effect of coil turns on coil sensitivity, design coils 2 and 3, and change only the coil turns N, while keeping other parameters unchanged.
e detailed geometry of the coil is shown in Table 6. e time-varying magnetic field is measured using coil 1, coil 2, and coil 3, respectively, and the induced voltage at 6 m is obtained in the time domain, and the frequency domain is obtained by FFT transformation of the time domain as shown in Figure 13. e RMS value of the induced voltage is shown in Table 7 in the time domain diagram, and the frequency domain diagram shows that the operating frequency of the time-varying magnetic field is 75 Hz, which is     the same as the rotation frequency of the motor. From equation (15), the RMS value of the induced voltage of each coil was transformed into the RMS value of the time-varying magnetic field strength and compared with the theoretical value, and the results are shown in Table 7. From the comparison between the experimental and theoretical values of coil 1 and coil 3 in Table 7, it can be seen that when the cross-sectional area of the coil increases from 0.36 m 2 to 2.82 m 2 , the measurement error of the same timevarying magnetic field decreases by 6.8%. By comparing the experimental and theoretical values of coils 2 and 3, the number of coil turns increased from 11 to 21, and the timevarying magnetic field measurement error of the same target environment was reduced by 3.89%. erefore, the coil sensitivity can be improved by increasing the coil crosssectional area and turns. e measurement error of all three coils is less than 10%, which proves that the normalized analytical model of coil sensitivity is correct and can be used for the design of different models of magnetic induction coils for super-low-frequency mechanical antennas.

Communication Experiment.
Antenna communication is through the coupling between the transmitting antenna and receiving antenna to complete the exchange and transmission of information.
e modulation of the transmission signal has good penetration and stability in air and various media, and the signal is not easily distorted. 2FSK modulation is a binary digital frequency modulation, and the modulation method is shown in Figure 3. is study builds an experimental platform as shown in Figure 12 to simulate the signal modulation of 2FSK for wireless communication experiments. e transmission signal is selected as a square wave signal as shown in Figure 14(a). Rotation frequencies of 60 Hz and 200 Hz correspond to input voltages of 0.5 V and 1.6 V, respectively. When the motor receives the input square wave signal, it drives the permanent magnet to rotate to form a radiation field, and the waveform diagram is shown in Figure 14(b). From 0 to 2.00 s, the input voltage of the motor is 1.6 V, and the radiation field frequency of the permanent magnet is 200 Hz. From 2.00 to 4.00 s, the input voltage of the motor is 0.5 V, and the radiation field frequency of the permanent magnet is 60 Hz. erefore, the modulation rate is 70 Hz/s. e two waveforms correspond to the symbols 1 and 0 of the modulated signal. e waveform is processed by the short-time Fourier transform to obtain the time-frequency domain as shown in Figure 14(c).
As shown in Figure 14, the input signal waveform of the mechanical antenna communication system is almost identical to the time-frequency domain of the output signal. It can be seen from Figure 14(c) that the graph of the short-  time Fourier transform has a certain slope when the frequency changes abruptly. Due to the transient nature of the speed of the drive motor, there is a process (Δt) of changing the frequency in the time-frequency domain diagram at the time of shear, making the frequency change at the slash. e frequency rise process time is 0.102 s, and the frequency fall process time is 0.205 s. e total change process is Δt � 0.307 s, so the bit-error rate of the source in the 2FSK communication system is 7.68%. e experimental results are the same with the preset condition trends and values, which verifies the effectiveness and feasibility of the rotating permanent magnet-based super-low-frequency mechanical antenna communication method described in this paper from the practical application level.

Conclusions
Traditional SLF antennas are bulky, power-consuming, and inefficient. is paper introduces a mechanical antenna with a rotating permanent magnet as a radiation element and a triaxial orthogonal coil as a receiving element. For radiation unit, a mathematical model based on rotating permanent magnet and radiation power is established. For the receiving unit, a mathematical model based on the dimension parameters and sensitivity of the square coil is established.
According to the analysis of theory, simulation, and experimental results, some characteristics of the mechanical antenna communication mechanism are obtained as follows: (1) For the radiating element of a mechanical antenna, the near-field radiated power is proportional to the square volume of the permanent magnet. Increasing the volume of the permanent magnet can increase the radiated power, thus increasing the communication distance. In addition, the modulation of the 2FSK signal can be realized by real-time control of the motor speed. e modulation rate is 70 Hz/s, and the bit-error rate is 7.68% during communication.
From above, the mechanical antenna subverts the excitation of ultra-low-frequency electromagnetic waves. However, compared with the existing ESA technology, the mechanical antenna cannot significantly increase the effective radiated power under the same dipole moment condition. Now, mechanical antenna is difficult to replace the existing high-power transmitter. At present, the research on mechanical antenna at home and abroad mainly focuses on radiation excitation, realization mode, and experimental verification.

Data Availability
e data used to support the findings of this study are included within the article.

Conflicts of Interest
e authors declare that they have no conflicts of interest.