An Intersection Platoon Speed Control Model Considering Traffic Efficiency and Energy Consumption in CVIS

. This paper proposed an intersection platoon speed control model considering traﬃc eﬃciency and energy consumption in the cooperative vehicle-infrastructure systems (CVIS) environment. This model divides the control situation in detail according to the diﬀerent state of signal lights at the intersection and splits the platoon that cannot pass the intersection completely. The optimization model is established by taking the traﬃc delay and energy consumption of the platoon as the control objectives, and the model is solved by using a genetic algorithm (GA). Finally, the simulation platform is built by SUMO traﬃc simulation software, MATLAB, and Python to verify the model. The simulation results show that the total number of queued vehicles, the maximum number of queued vehicles, and the mean travel time of vehicles decreased by 77.81%, 33.33%, and 10.95%, respectively. Besides, the total fuel consumption is reduced by 19.95%, the total emissions of CO 2 , CO, HC, NO x , and PM x decreased by 19.96%, 58.55%, 51.33%, 23.81%, and 37.51%, respectively. It indicates that the proposed platoon speed control model can eﬀectively improve traﬃc eﬃciency while reducing energy consumption and pollutant emissions.


Introduction
With the rapid growth of car ownership, the existing urban traffic infrastructure construction level cannot meet the growing demand for traffic travel, and urban traffic problems are increasingly serious [1,2]. As the key node of urban road traffic, the traffic efficiency of the intersection is getting worse and worse [3]. In the traditional "go-stop" type transport operation mode, the collaboration between the vehicles is less, and the vehicle just passively accept intersection signal control, which leads to the vehicle in the process of the intersection of frequent deceleration or startstop, thus reducing the efficiency of intersection, increasing energy consumption and pollutant emissions of the vehicle at the same time, and causing traffic congestion, environmental pollution, and a series of problems [4,5].
Researchers have carried out a large number of studies on improving the efficiency of intersections. In the traditional sense, the improvement of intersection efficiency mostly focuses on the optimization of intersection signal control. Tan et al. [6] studied the continuous-time and discrete-time signal timing models for the classical isolated signalized intersection with only two one-way vehicle flows and proposed a gradient descent algorithm. Wu et al. [7] established a cellular automata model with greedy algorithm for the traffic control of intersections in autonomous vehicle environment. Jin et al. [8] proposed a multiobjective agent-based framework for road traffic controls to tackle the challenges of increasing traffic congestion and other negative impacts. Rafter et al. [9] proposed a new traffic signal control algorithm, multimode adaptive traffic signals (MATS), which combines information from existing fixed-time plans and loop detectors, and position data from connected vehicles to perform decentralized control on signalized intersections. Wu et al. [10] proposed a novel multiagent recurrent deep deterministic policy gradient (MARDDPG) algorithm based on deep deterministic policy gradient (DDPG) algorithm for traffic light control (TLC) in vehicle networks.
At present, with the rapid development of artificial intelligence and wireless communication technology, cooperative vehicle-infrastructure system (CVIS) is increasingly mature [11,12]. Vehicles are equipped with advanced sensors, controllers, actuators, and other devices and integrated vehicle positioning technology and modern communication technologies such as 5G to realize the transmission and sharing of traffic information between vehicles, roadside facilities, pedestrians, and the cloud. Under the environment of CVIS, the intersection control centre can obtain the information of surrounding vehicles and signal lights in real time and control the speed of intelligent vehicle through data fusion and data processing technology, so as to better improve the efficiency of the intersection [13][14][15]. In the research of speed control, Lee and Li [16] proposed an eco-driving advisory system (EDAS) that reduces CO 2 emissions and energy consumption by letting the vehicle continuously pass through multiple intersections with the minimum possibilities of stops. Mintsis et al. [17] used a detailed microscopic simulation model of a city network in essaloniki, Greece, as a test bed to evaluate the performance of dynamic eco-driving for different penetration rates of the dynamic eco-driving technology and varying traffic conditions. Yang et al. [18] conducted real-world vehicle driving measurements to directly study the effectiveness of SG-ITS in terms of driving behaviour, time savings, fuel consumption, and pollutant emissions by driving vehicles on the same routes with and without SG-ITS speed guidance. Considering the queuing effect and the driver's actual tracking error, Zhang et al. [19] proposed a vehicle queuing length estimation method based on V2I technology to predict the effective green time and developed a hierarchical GLOSA system. Shen et al. [20], considering the velocity plan and longitudinal dynamics control of the vehicle, proposed a control framework for connected and automated vehicles (CAVs), and the effectiveness of these converters was verified by the cosimulation of CarMaker-Simulink. Lin et al. [21] considered more realistic powertrain dynamics, including the engine and the transmission as well as aerodynamic resistance, rolling resistance, etc., explicitly describing dynamic behaviour and fuel characteristics at acceleration, deceleration, and constant speed. Wu et al. [22] simultaneously optimized signal timing and vehicle speed and dynamically adjusted vehicle arrival time through speed guidance.
Most of the above studies are carried out on the speed control of vehicles traveling alone. Platoon can maintain a smaller distance between vehicles than if the vehicles were traveling alone on the road, thus allowing the road to accommodate more vehicles, increasing the capacity and the throughput of the road [23]. At the same time, platoon can reduce the resistance of each vehicle, so as to reduce the energy consumption of vehicles. e wireless communication between vehicles in the CVIS environment improves the safety of platoon [24][25][26]. At present, most of the researches on the platoon are focused on the control and stability of a single platoon. Some scholars also consider the actual road intersection environment and study the platoon in terms of improving the traffic efficiency of the intersection. Ma et al. [27] proposed ecological cooperative adaptive cruise control (Eco-CACC) based on V2X communication, combining the advantages of eco-driving and car following to minimize the energy consumption of connected automated vehicle platoon. Feng et al. [28] transformed the problem of intersection capacity maximization into how to minimize the intersection arrival time of vehicles in the green phase, and designed a composite trajectory planning strategy architecture for platoon trajectory optimization. Faraj et al. [29] proposed an effective and complete platoon-based speed optimization scheme to minimize idle time near signalized intersection. Wang et al. [30] considered longitudinal safety and designed a intersection platoon control algorithm, which takes maximizing the efficiency of the intersection capacity within a given green time as the main priority and minimizing emissions as the second priority. Bisht and Shet [31] prioritized platoons according to their proximity to intersection and designed and evaluated an intersection platoon collaboration algorithm based on V2X communication. However, there are fewer studies on the combination of platoon and intersection speed control, and most of them do not consider the impact of platoons that fail to pass the intersection and need to slow down and stop. erefore, in order to improve the operation efficiency of intersections and reduce energy consumption, this paper combines the platoon and speed control under the CVIS environment. First of all, on the basis of defining the intersection speed control area, taking the travel delay of the platoon as the control target, the overall speed control of the platoon is carried out, so that more platoons can pass the intersection during the green light. At the same time, considering the platoon that cannot pass the intersection to carry on the split control, so that as many vehicles in the platoon as possible through the intersection and with the minimum energy consumption as the control target to guide the vehicles that cannot pass through the intersection to slow down and stop. Based on this, an optimization model considering traffic efficiency and energy consumption is established and solved by genetic algorithm (GA) that has better convergence and faster solving speed compared to traditional optimization methods. e organizational structure of this paper is as follows: Section 2 introduces the intersection scenario and the assumptions of the research content. Section 3 introduces the methodology of the intersection platoon speed control model considering traffic efficiency and energy consumption in CVIS proposed in this paper. Section 4 uses SUMO, MATLAB, and Python to design a comparative simulation experiment. Section 5 discusses and analyses the experimental results. Finally, the conclusion and research perspectives are drawn in Section 6.

Problem Statement and Assumptions
is paper studies a typical symmetrical signal intersection with four entrance lanes. As shown in Figure 1, each entrance lane includes three directions: left turning, straight going, and right turning. e four entrance roads and four exit roads of the intersection are represented by E1-E8, respectively. erefore, without considering the turn back of vehicles, the traffic flow of the intersection is the following 12 direction: Mathematical Problems in Engineering e intersection adopts a fixed period signal control scheme, with a period duration of C, according to the flow direction of traffic flow, and it is divided into the following four phases (as shown in Table 1): west-east straight travel (WES), west-east left turn (WEL), north-south straight travel (NSS), and north-south left turn (NSL). Since the right turning vehicle has little influence on the traffic flow of the intersection, the research in this paper does not consider the impact of right turning. e control range of the intersection control centre is the road L meters away from the intersection stop line on each entrance road. When the platoon reaches the control range, the platoon realizes the intersection traffic information interaction through vehicle-tovehicle and vehicle-to-road communication and adjusts the speed.
In order to specify the research object, the research of this paper is also based on the following basic assumptions: (1) the vehicles running on the road are all intelligent connected vehicles that can realize vehicle-tovehicle and vehicle-to-infrastructure communication. e vehicles arrive at the intersection in the form of a platoon, and the platoon will drive according to the speed calculated by the control center. (2) e intersection control center can obtain all kinds of traffic operation information at the intersection, and the packet loss or delay of communication between vehicles and between vehicles and infrastructures is ignored. (3) e road surface is flat, and the influence of slope on vehicles is ignored. (4) ere is no position conflict with the side platoons when each platoon passes through an intersection.

Materials and Methods
In this paper, the intersection platoon speed control model considering traffic efficiency and energy consumption in CVIS includes three parts: determination method of control area, platoon overall speed control strategy, and platoon split speed control strategy, as shown in Figure 2.  (a) e length of the control area is defined according to the information of the platoon scale, the maximum and minimum speed limit of the vehicles, and the maximum acceleration and deceleration of the vehicles, so as to achieve the optimal control effect. (b) is model divides and analyses the state of traffic lights at the intersection in detail and gives the judgment conditions and constraint conditions of each situation. Taking the minimum travel delay as the control goal, the platoon overall speed control strategy is constructed. (c) e platoon split control strategy is built, and the basis of the platoon split is given. For the platoon that needs to slow down and stop at the intersection, the control function of the energy consumption of the platoon is built according to the VSP vehicle fuel consumption model, and the control goal is to minimize the energy consumption.

Determination Method of the Control Area.
In this paper, the intersection speed control area is defined. e shortest range of speed control area is to ensure that no matter what speed the platoon enters the control area, it has enough time to adjust its speed. erefore, the length of the speed control area of the platoon should not be less than the distance for the whole platoon to adjust its speed, namely, where v max is the maximum speed limit of vehicles on the road; v min is the minimum speed limit of vehicles on the road; a max is the absolute value of the maximum acceleration of vehicles on the road; d max is the absolute value of the maximum deceleration of vehicles on the road. To ensure that the platoon can pass the intersection as soon as possible and reduce the interference to downstream platoons, the longest control range is that even if the platoon enters the intersection control area at the beginning of the current green light at the minimum speed, the platoon can still completely pass the intersection at the end of the next green light, namely, where G is the green light duration of the signal light; L pmax is the maximum length of the platoon on the road and can be calculated using equations (3) and (4): where L p,i,j is the length of the jth platoon arriving at the intersection control area in the ith traffic flow direction; N i,j is the platoon scale of the jth platoon arriving at the intersection control area in the ith traffic flow direction; l is the length of the vehicles in the platoon; ∆l is the spacing between vehicles in the platoon. From the above analysis, it can be seen that the defined range of the length L of the intersection speed control area is as follows:

Platoon Overall Speed Control Strategy.
In the CVIS environment, through wireless communication between vehicles and between vehicles and infrastructures, when the platoon reaches the speed control area of the intersection, the control centre of the intersection obtains the traffic information such as the position, speed, scale of the platoon, and the current phase of the signal light at the intersection and builds an optimization model to calculate the optimal speed of the platoon through the obtained traffic information, so as to control the overall speed of the platoon.

Construction of Control Function.
e purpose of platoon overall speed control is to improve the operational efficiency of transport system, the operational efficiency of the transport system can be expressed by the travel delay of the platoon, and the travel delay of the platoon can be expressed as the difference between the time it takes for the platoon to actually arrive at the intersection and the time it takes for the platoon to arrive at the intersection at free flow speed. In this study, in order to avoid road traffic flow have great speed fluctuation, the platoon reaches the intersection stop line at a uniform speed after the platoon is adjusted to the optimal speed. en, the actual time of the platoon arriving at the intersection stop line includes the time of speed adjustment and the time of the platoon driving at uniform speed. en, the calculation equation of the travel delay of the platoon is as follows: where v 0,i,j is the initial speed of the jth platoon arriving at the intersection speed control area in the ith traffic flow direction; v t,i,j is the optimized speed of the jth platoon arriving at the intersection speed control area in the ith traffic flow direction; a i,j is the acceleration used to adjust the speed of the jth platoon arriving at the intersection speed control area in the ith traffic flow direction; v f is the speed of free flow on the road. erefore, the control goal of the platoon overall speed control strategy is to minimize the travel delay of the platoon, namely,

Control Situation Division.
According to the signal light state when the platoon reaches the control area of the intersection, the control situation is divided in detail. e signal light status when the platoon reaches the control area is divided into green and red. Based on the remaining signal light duration and other information, the judgment conditions and the restriction conditions that the platoon can pass the intersection without stopping are given on the basis of calculation and analysis of each situation.
(1) Calculation of Relevant Important Parameters. In order to facilitate the description and the construction of the strategy, the important parameters needed in the strategy are firstly calculated: (1) e maximum time required of a platoon to reach the stop line at the intersection e maximum time required of a platoon to reach the stop line at the intersection is the time required by the platoon to slow down to the minimum speed and maintain the minimum speed to reach the stop line at the intersection at a uniform speed. e calculation equation is as follows: (2) e minimum time required for all vehicles in a platoon to pass the intersection e minimum time required for all vehicles in a platoon to pass the intersection is the time required for the platoon to accelerate to the maximum speed at the maximum acceleration and maintain the maximum speed to uniformly pass the intersection. e calculation equation is as follows: (3) e maximum time required for all vehicles in a platoon to pass the intersection In order to ensure the traffic efficiency of the intersection, in this paper, for the platoon that decelerates through the intersection, after the first vehicle in the platoon reaches the stop line of the intersection, the platoon immediately recovers to the initial speed with the maximum acceleration. erefore, the maximum time required for all vehicles in a platoon to pass the intersection is the time required for the platoon to slow down to the minimum speed and maintain the minimum speed to reach the stop line at the intersection and then accelerate to the initial speed so that all vehicles in the platoon completely pass the intersection. e calculation equation is as follows:

Mathematical Problems in Engineering
(2) Platoon Speed Control under Green Light Situation. Suppose that T 0,i,j is the time when the jth platoon arrives at the intersection control area in the ith traffic flow direction, and T g,i,j is the end time of the current green phase when the jth platoon arrives at the intersection control area in the ith traffic flow direction. When the platoon arrives at the intersection control area and the intersection signal light is green, the speed control of the platoon can be divided into the following three situations: (1) Uniform passage situation When T g,i,j − T 0,i,j ≥ (L + L p,i,j )/v 0,i,j , it indicates that if the platoon keeps the current speed after arriving at the intersection control area, the signal light is still green when arriving at the intersection, and the remaining green time is long, which can make all the vehicles in the platoon pass the intersection. At this time, in order to avoid the large speed fluctuation of the platoon, the platoon should adopt uniform speed control strategy to make the vehicles in the platoon keep the current speed. (2) Accelerated passage situation When t min ≤ T g,i,j − T 0,i,j < (L + L p,i,j )/v 0,i,j , it indicates that if the platoon keeps the current speed after arriving at the intersection control area, there will be two situations: one is that the signal light will turn red when the platoon reaches the stop line at the intersection, so that none of the vehicles in the platoon can pass the intersection; the other is that the signal light is still green when the platoon reaches the stop line at the intersection, but the remaining green time is short, so only some vehicles in the platoon can pass the intersection. But in both cases, if the platoon accelerates with maximum acceleration and reaches the maximum speed limit on the road, it can pass the intersection in the remaining green time. erefore, in order to avoid unnecessary start-stop and parking waiting of vehicles in the platoon, the platoon should pass the intersection at the current green phase as much as possible, so the acceleration control strategy should be adopted for the platoon, as shown in Figure 3, the constraint is shown in the following equation: (3) Cannot passage situation When 0 < T g,i,j − T 0,i,j < t min , it indicates that if the platoon keeps the current speed after reaching the control area of the intersection, the signal light will turn red when it reaches the stop line of the intersection, or it will still be green but the remaining time is very short, which can only make part of the vehicles in the platoon pass the intersection or make all the vehicles in the platoon unable to pass the intersection. In addition, even if the platoon speeds up to the maximum speed with maximum acceleration, it cannot completely pass the intersection in the current green phase. At this time, it is necessary to turn to the platoon split stage.

(3) Platoon Speed Control under Red Light Situation.
Suppose that T r,i,j is the end time of the current red light phase when the jth platoon in the ith traffic flow direction arrives at the intersection control area; T g,i,j,1 is the end time of the green phase when the jth platoon in the ith traffic flow direction arrives at the intersection control area under red light situation; t q is the queuing dissipation time at the current intersection, where H is the queue length at the current intersection, v q is the dissipation speed of the queue at the current intersection, and t l is the start-up loss time of the vehicle. en, when the platoon reaches the intersection control area and the intersection signal light is red, the speed control of the platoon can be divided into the following four situations: (1) Cannot passage situation When T r,i,j − T 0,i,j + t q > t max , it indicates that if the platoon keeps the current speed after reaching the control area of the intersection, there will be two situations when it reaches the intersection: one is that the signal light will still be red, the other is that the signal light will turn green but there are long queue lengths at the intersection. And, even if the platoon slows down to the minimum speed limit with maximum deceleration, the platoon still unable to pass the intersection. At this point, it is necessary to turn into the platoon split stage. (2) Decelerated passage situation When L/v 0,i,j < T r,i,j − T 0,i,j + t q ≤ t max and T g,i,j,1 − T 0,i,j ≥ t max1 , it indicates that if the platoon keeps the current speed after reaching the control area of the intersection, there will be two situations when it reaches the intersection: one is that the signal light will still be red, the other is that the signal light will turn green and there are queuing vehicles at the intersection. But if the vehicles in the platoon slow down to the minimum speed limit with maximum deceleration, they can pass the intersection within the next green time. erefore, the deceleration control strategy should be adopted for the platoon, as shown in Figure 4, and the constraints are shown in equations (12) and (13):

6
Mathematical Problems in Engineering (3) Uniform passage situation When 0 < T r,i,j − T 0,i,j + t q ≤ L/v 0,i,j and T g,i,j,1 − T 0,i,j ≥ (L + L p,i,j )/v 0,i,j , it indicates that if the platoon keeps the current speed after reaching the control area of the intersection, the signal light will turn green and queues at the intersection have dissipated when arriving at the intersection, and the remaining green time is long, which can make all the vehicles in the platoon pass the intersection. At this time, the platoon should adopt uniform speed control strategy to make the vehicles in the platoon keep the current speed. (4) Accelerated passage situation When 0 < T r,i,j − T 0,i,j + t q ≤ L/v 0,i,j and t min < T g,i,j,1 − T 0,i,j ≤ (L + L p,i,j )/v 0,i,j , it indicates that if the platoon keeps the current speed after reaching the control area of the intersection, the signal light will be green, but the rest of the green time can only make the platoon some of the vehicles reach the intersection. If the platoon speeds up to the maximum speed with maximum acceleration, it can completely pass the intersection in the green phase.
erefore, acceleration control strategy should be adopted for the platoon, as shown in Figure 5, and the constraints are shown in equations (14) and (15): To sum up, the flow chart of control situation division is shown in Figure 6:

Constraints
(2) Acceleration constraint: where T Ni,j−1,i,j−1 is the time when the last vehicle of the j−1th platoon in the ith traffic flow direction reaches the intersection stop line and T 1,i,j is the time when the first vehicle of the jth platoon in the ith traffic flow direction reaches the intersection stop line.

Platoon Split Speed Control Strategy.
In order to maximize the throughput of the intersection, improve the operation efficiency of the traffic, and make more vehicles can pass the intersection without stopping during the green time, for the platoon that cannot pass the intersection through the platoon overall speed control strategy, the platoon split speed control strategy is transferred to, as shown in Figure 7. In this paper, the platoon split speed control strategy considers the following two situations: (a) For the platoon that still cannot pass the intersection through the acceleration control strategy, the platoon split speed control is carried out. First, the number of vehicles that can pass the intersection is calculated if the platoon accelerates to the maximum speed limit of the road with the maximum acceleration, and then the platoon is divided into P 1 and P 2 . erefore, the number of vehicles in platoon P 1 and P 2 is calculated as shown in equations (20) and (21): where N 1 are the number of vehicles in the split platoon P 1 ; N 2 are the number of vehicles in the split platoon P 2 ; and Gr is the remaining green duration. For P 1 , since the platoon accelerates to its maximum speed at maximum acceleration, it can pass the intersection at the current green time, it still accelerates through the intersection according to the platoon overall speed control strategy in Section 3.2, taking the minimum travel delay as the control objective function, and the constraints are the same as those in Section 3.2. For platoon P 2 , as the platoon is no longer able to pass the intersection, the platoon is controlled to slow down and stop with the control objective of minimum fuel consumption. (b) For the platoon that still cannot pass the intersection through the deceleration control strategy, the platoon has slowed down to the minimum speed limit and still cannot pass the intersection, so the platoon should be controlled to slow down and stop at the minimum fuel consumption.
In this study, for the control of the platoon with the minimum fuel consumption and stop, by VSP fuel consumption model to build the platoon's energy consumption model. VSP fuel consumption model is a fuel consumption model based on the specific power of the vehicle, which takes into account rolling resistance and aerodynamic drag as well as changes in the kinetic and potential energy of the vehicle [32]. e basic driving behaviour during the deceleration and stop process of the platoon is regarded as the process of driving at a uniform speed for a period of time and then slowing down and stopping, so the fuel consumption of the process can be calculated by the following equation: where t 1 is the time of the platoon moving at uniform speed; t 2 is the time of uniform deceleration movement of the platoon; VSP can be calculated using the following equation: where ε i is the "mass factor," which is the equivalent translational mass of the rotating components (wheels, gears, shafts, etc.) of the powertrain, the suffix i indicates that is gear-dependent.; grade is the vertical rise/slope length; g is the acceleration of gravity; C R is the coefficient of rolling resistance Mathematical Problems in Engineering 9 (dimensionless); C D is the drag coefficient (dimensionless); A is the frontal area of the vehicle; ρ a is ambient air density (1.207 kg/m 3 at 20°C � 68°F); v w is the headwind into the vehicle, m is the mass of the vehicle.
Since the vehicles studied in this paper are all light vehicles, the calculation equation of VSP can be simplified as follows [33]: where A � 0.156461, B � 0.002002, C � 0.000493, and m � 1.4788. erefore, the control function of platoon energy consumption built based on VSP model in this paper is shown as follows: e constraint conditions are In equation (26), L q is the distance between the lead vehicle of the platoon that needs to slow down and the stop line of the intersection when the platoon reaches the control area of the intersection.

Simulation Experiment
In this study, the proposed control model is verified by using SUMO, MATLAB, and Python, and the overall flow of the simulation is shown in Figure 8. SUMO is used to build a typical intersection simulation environment, and the number of lanes, signal light cycle, signal light phase, traffic flow, and so on are set. e total cycle time of the signal light is 88 s, in which the west-east straight travel phase is 29 s, the west-east left turn phase is 15 s, the north-south straight travel phase is 25 s, and the north-south left turn phase is 19 s, as shown in Figure 9. e input traffic flow of each lane at the intersection and other simulation parameters are shown in Table 2, and the input vehicles are randomly formed into the platoon. At the same time, the minGap parameter between vehicles is set to 1.5 m to ensure the traffic safety during the operation of the platoon. e carfollowing model during the operation of the platoon adopts the improved Krauss model [34]. e Traci interface of SUMO software is used to realize the interaction with Python. When the platoon reaches the control area of the intersection; various traffic information of the platoon and the signal light is obtained. In MATLAB, the optimization solution model is established through the genetic algorithm (GA), and the optimal solution is obtained through selection, crossover, mutation, and other operations based on the theory of biological evolution. e traffic information such as the speed and remaining time of signal light when the platoon enters the control area of the intersection is taken as input variables, and the optimal speed and acceleration values of the platoon were obtained, which were input into the SUMO software.
Since the model in this paper does not involve the change of signal light phase order, the speed control and result analysis are only carried out for the platoon running in the straight lane at the west entrance. In order to make a comparative analysis with the proposed intersection platoon speed control model, a comparative experiment was carried out in the case of no intersection platoon speed control. In the same intersection simulation environment, the two experiments were simulated with 3,600 steps in SUMO, and the platoon trajectory, the traffic efficiency information (number of queued vehicles at intersection, mean travel time), energy consumption, and emissions information (fuel, CO 2 , CO, HC, NO x , and PM x ) of the platoon were obtained.

Results and Discussion
is paper discusses and analyses the experimental results from the following three aspects: Figures 10-15 shows the comparison of platoon trajectory. It can be seen from the platoon trajectory of the platoon under various working conditions that, through the speed control model of the platoon in this paper, the platoon can make as many vehicles in the platoon pass through the intersection without stopping by accelerating, decelerating, and splitting, thus reducing the start-stop and idle speed of vehicles and thus increasing the throughput of the intersection. At the same time, it can be seen from the platoon trajectory diagram that decelerates and stops that the paper takes the minimum fuel consumption as the control objective to control the vehicle to decelerate in advance, which makes the platoon trajectory smoother and the speed fluctuation smaller.

Traffic Efficiency Analysis.
As can be seen from Table 3, the total number of queued vehicles at the intersection decreased by 77.81%, and the maximum number of queued vehicles decreased by 33.33%. And, after speed control is implemented, the number of vehicles in queue is reduced in most cases as shown in Figure 16. Causing a decline in the number of queuing vehicles for two reasons, on the one hand, most of the platoon can undertake speed adjustment in advance by the platoon speed control model proposed in this paper and make as many vehicles through the intersection during the green light, thus reducing the intersection driveway lined up and vehicle parking waiting, reduce traffic congestion; on the other hand, as shown in Figure 15, take an example of the speed trajectory of a platoon that needs to slow down and stop; the speed trajectory graph of the platoon slowing down and stopping at the intersection shows that, as the platoon split speed control strategy controls the platoon that cannot cross the intersection at the green light time, slowing down and stopping with minimum fuel consumption makes the platoon slow down earlier, which to some extent also leads to a reduction in the number of vehicles queuing at the intersection and controls the platoon to slow down earlier; the speed trajectory of the vehicle is smoother and the speed fluctuation is smaller.
Meanwhile, the mean travel time of vehicles is reduced by 10.95%. As can be seen from the broken line in Figure 17, in most cases, the mean travel time curve with platoon speed control is below or near the mean travel time curve without platoon speed control and is relatively stable. erefore, it can be seen that, on the basis of ensuring the stability of traffic operation, the speed control strategy proposed in this paper can reduce the average traffic time and improve the efficiency of traffic operation.

Analysis of Energy Consumption and Pollutant Emissions.
In terms of energy consumption and pollutant emissions, it can be seen from Figure 18 that, after the proposed platoon speed control, the total fuel consumption is reduced by 19.95%, and the total emissions of CO 2 , CO, HC, NO x , and PM x are reduced by 19.96%, 58.55%, 51.33%, 23.81%, and 37.51%, respectively. On the one hand, the overall speed control strategy proposed in this paper reduces the start-stop and idle speed of vehicles near the intersection. On the other hand, the proposed platoon split speed control strategy has carried out speed optimization treatment with minimum fuel consumption as the control objective for the platoon that fails to pass the intersection. is indicates that the speed control strategy   proposed in this paper is effective in reducing energy consumption and pollutant emissions during traffic operation.
In conclusion, compared with no intersection platoon speed control, the intersection speed control model proposed in this paper can reduce the number of queued vehicles and travel time while effectively reducing the energy consumption and total pollutant emissions in the process of traffic operation and ensure the energy saving and high efficiency in the process of traffic operation. Platoon trajectory without speed control

Conclusions
In this paper, an intersection platoon speed control model considering traffic efficiency and energy consumption is proposed to improve traffic efficiency and reduce energy consumption and pollution gas emissions during traffic operation. Firstly, this paper constructs the platoon overall speed control strategy. On the basis of defining the speed control area of the intersection, the state of the signal light when the platoon arrives at the control area is divided in detail. Meanwhile, the judgment conditions of each situation and the corresponding restrictions that make the platoon pass the intersection without stopping are given. For the platoons that cannot pass the intersection in the green phase through the overall speed control strategy, a platoon split speed control strategy is constructed in order to allow as many vehicles as possible to pass the intersection and to minimize the fuel consumption of vehicles that cannot pass the intersection. e model is solved and verified by SUMO, MATLAB, and Python. Simulation results show that, compared with the no platoon speed control, under the intersection platoon speed control model considering traffic efficiency and energy consumption proposed in this paper, the total number of queued vehicles at the intersection decreased by 77.81%, the maximum number of queued vehicles decreased by 33.33%, and the mean travel time of vehicles is reduced by 10.95%. e total fuel consumption is saved by 19.95%, and the total emissions of CO 2 , CO, HC, NO x , and PM x are reduced by 19.96%, 58.55%, 51.33%, 23.81%, and 37.51%, respectively. is indicates that the optimal control effect of the platoon speed control model proposed in this paper is good, which can ensure the traffic efficiency and reduce the energy consumption and pollution gas emissions in the process of traffic operation. For future work, we plan to further consider the traffic signal factors on the basis of the platoon speed control model proposed in this paper, so as to better improve the operational efficiency of traffic and environmental protection.

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.