Partially Replacing the Emulsified Asphalt in Cement Emulsified AsphaltMortars with Epoxy Emulsion:Mechanical Properties and Durability Study

Cement emulsified asphalt (CEA) mortars achieve insufficient bond strength with substrate cement concrete slab. To ameliorate problems emerging from this, the emulsified asphalt (EA) in CEAmortars was partly replaced by epoxy emulsion (EE) at contents of 0%, 10%, 20%, and 30%, yielding CEA mortars with enhanced properties. (e bond strength, mechanical strength, toughness, and durability (including drying shrinkage and erosion resistance) of modified CEA mortars were assessed. (e results showed that partial replacement of EA with EE improved the bond strength, mechanical strength, drying shrinkage, and erosion resistance of CEA mortars. A good correlation was found between the proportions of the EE replacement and the bond strength of CEA mortars. Partial replacement of EA with a small amount of EE exerted no significant effect on the toughness of CEA mortar. (e stronger network structure of CEA mortars containing EE improved the compactness, thus improving the performance of CEA mortars. Based on these findings, EE is suggested as partial replacement of EA for enhancing the properties of CEA mortars.


Introduction
Today, polymer-modified cement mortars are widely used in concrete structures as finishing or repair materials to prolong the service life of infrastructures [1,2]. It has been acknowledged that polymer-modified cement mortars not only maintain the properties of cement mortars but also utilize the properties of polymers. us, they obtain good bond strength, excellent toughness, and other desired properties [3]. Cement emulsified asphalt (CEA) mortars retain most of the characteristics of cement and asphalt, including long fatigue life, the low-temperature sensitivity of cement, and the high toughness of asphalt. Because of the above properties, CEA mortars are commonly applied in railway tracks as a bedding layer between the track slab and the concrete foundation to dissipate and reduce track vibrations generated by trains passing at high speeds. Additionally, CEA mortars are also used as repair materials for cement pavements or other cement infrastructures [4,5].
CEA mortars need to have good coordination deformation ability and interface bond strength with the concrete slab when used as a bedding layer between the track slab and the concrete foundation or as repair materials. However, researches by Liu et al. [6] and Peng et al. [7] indicated that CEA mortars do not yield sufficient interfacial bond strength with cement concrete. Measures to improve the bond strength of CEA mortars have received considerable attention. Liu et al. [8] pointed out that incorporation of stabilizers in CEA mortars increased the interfacial bonding strength. e debonding rate and gap width of CEA mortars with stabilizers decreased sharply. Peng et al. [7] investigated the interfacial bonding strength of two types of CEA mortars via pull-off tests and showed that the bonding strength of the CEA mortar with a high A/C ratio exceeded that with low A/C ratio. e bonding strength of CEA mortars was also enhanced by polymer latexes. Zhang et al. [9] showed that the addition of acrylate latexes and expansion agent improved the interlayer bonding of CEA mortar and concrete composite specimens. e reason for this improvement was the excellent bond performance of acrylate latexes and the enhanced mechanical interlock achieved by the expansion agent.
It has been suggested that polymer latexes may be used as a modifier for cement mortar and concrete to improve the adhesion and bond strength because of its excellent bonding properties and microstructure transformation of mortar and concrete [10][11][12]. Epoxy emulsion (EE), as common polymer latexes, has been widely applied to modify cement mortars or concrete. Xiao et al. [13] prepared a high-performance cement with EE and showed that the addition of EE slightly increased the mechanical properties and corruptness resistance of modified cement mortars. e reason is the formation of a three-dimensional structure in the cement hydration system, which bridges phases by EE. e dense structure of cement epoxy emulsion mortar (because of the cross-linking structure formed by cured epoxy resin with cement hydration products) also enhances erosion resistance [14]. Furthermore, Zheng et al. [15] investigated the hydration process of EE enhanced cement mortar and showed that the evolution of the modified cementbased paste can be divided into four stages based on the normalized heat flow. e bonding strength and bending ability of mortars were improved by the addition of epoxy resin. Studies by Pang et al. [16] and Zuo et al. [17] also showed that the mechanical strength and bond strength of cement epoxy emulsion mortar improved with increasing EE contents. Numerous attempts have been made to obtain EE-modified EA composite emulsions. Gu et al. [18] investigated the compatibility between the cured phase-inversion waterborne epoxy resin and EA, showing that increasing the content of waterborne epoxy resin improved the compatibility of the composite emulsion. Liu et al. [19] showed that the components and network microstructure of EE modified EA enhanced the cohesion property and viscoelasticity of this material. Li et al. [20] found that waterborne epoxy resin significantly increased the complex modulus of asphalt emulsion residues. Based on the above findings, it is clear that EE can be added to cement or EA, thus, enhancing their properties. CEA mortars mainly consist of cement and EA. However, attempts to utilize the advantages of EE to obtain reinforced CEA mortars with better bond strength, mechanical strength, and other properties remain inadequate to date. e bond strength and other properties of CEA mortars with partial replacement of EA by EE remain unclear.
In this study, part of EA in CEA mortars was replaced by EE with additions varying from 0% to 30% (at increments of 10%). e mechanical properties including bond strength, mechanical strength, toughness, anddurability including drying shrinkage and erosion resistance of modified CEA mortars wereinvestigated.

Raw Materials
(1) Cement not only provides the mechanical strength needed for CEA mortars but also absorbs water in EA and EE during the hydration process [21][22][23]. (2) SBR cationic EA was used in the experiment, as shown in Figure 1(a). Its properties are shown in Table 2. e test methods of EA followed Chinese Standard JTG E20-2011. (3) e main properties of nonionic waterborne EE and curing agent purchased from the Junhua building materials factory (Shanxi, Taiyuan, China) are shown in Tables 3 and 4, respectively. e appearances of EE and the curing agent are shown in Figures 1(b) and 1(c), respectively. e test methods of waterborne EE and the curing agent followed Chinese Standard GB/ T 36797-2018. e type of epoxy resin with an epoxy value of 0.51 mol/100 g in the epoxy emulsion was E 51. e curing agent was an amine curing agent with an amine value of 320 mol/100 g. e ratio of EE to the curing agent was 1 : 1 when used for CEA mortars, which was chosen according to the experience informed by a laboratory test. (4) River sand with a particle size between 0.32 and 4.75 mm and a fineness modulus of 2.7 was used as fine aggregate. Tap water was used in the experiment. (5) Studies by Tan et al. [24] and Ouyang et al. [25] showed that the addition of additives can effectively improve the performance of cement mortar. To improve the fluidity of CEA mortar, a naphthalene water-reducing agent (FDN-2) with a water-reducing rate of 20% was used at proportions of 1.8% by mass of cement according to practical experience. e FDN-2 water-reducing agent compounded by the β-naphthalene sulfonate was obtained from Shandong Wanshan Chemical Co., Ltd. (Shandong, Jinan, China). As air was introduced into the cement mortar mixture during the mixing process, a defoamer was necessary to reduce small bubbles. us, tributyl phosphate (C 12 H 27 O 4 P) obtained from Shandong Xinheng Chemical Co., Ltd. (Shandong, Jinan, China) was used as a defoamer at a ratio of 0.1% by mass of cement according to practical experience. In the research of Buoso et al. [26], Vo and Plank [27], and Liu et al. [28], the tributyl phosphate was also applied as a defoamer for cement mortar.

Preparation of Cement Emulsified Asphalt Mortar
Samples. Because of their better fluidity and mechanical strength (as identified by previous laboratory tests), CEA mortars with 40% EA content (by mass of cement) were selected. To determine the proportions of EE to replace EA, the compatibility and distribution of EE and EA in composite emulsions after curing were characterized. Figure 2 shows the fluorescence microscopic (FM) images of composite emulsions where EA was replaced by different contents of EE. In the FM images, epoxy resin is shown in yellow, while asphalt appears black. e area of the yellow epoxy resin in the FM images increased with increasing EE proportions. At an EE dosage below 30%, the epoxy resin was evenly distributed in the asphalt and formed a structure with asphalt as a continuous phase and epoxy resin as a dispersed phase. At an EE dosage of 30%, the epoxy resin interacted with asphalt and formed a network structure. However, at an EE dosage of more than 30%, EA and EE composite emulsion after curing showed an agglomeration structure, which was not conducive to the formation of an asphalt-epoxy network structure. is indicates that EA and EE could mix well when the proportion of EE replacing EA is less than 30%.
us, in this study, the replacement ratio of EE repla-cingEA was determined as 0%, 10%, 20%, and 30%, respectively. en, four types of CEA mortars (i.e., I, II, III, and IV) were designed. e proportions of CEA mortars and their fluidity tested according to Chinese Standard GB/ T2419-2005 are presented in Table 5. All samples were designed with a water-cement ratio of 0.38 and a cement-sand ratio of 1 : 2. It should be noted that the water contained in EA, EE, and the curing agent is not included in Table 5. e required water was calculated by equation (1): where M water refers to the mass of water in Table 5 (g); M cement refers to the mass of cement (g); M EA refers to the     Advances in Materials Science and Engineering mass of EA (g); M EE refers to the mass of EE (g); M curingagent refers to the mass of curing agent (g). During mixing, cement, sand, and additives were poured into the stirring pot and were evenly stirred for 30 s. en, water, EA, EE, and curing agent were prestirred until uniformity and blended with the mix for 3-4 min. Finally, mortars were shaped by the corresponding mold.

Bond Strength Test.
As applied by Qiao et al. [29], the flexural bond strength test was used to characterize the bond strength between the repair mortar and the OPC mortar/concrete. is method was also used to evaluate the bond performance of CEA mortars containing EE according to the Chinese standard JC/T 2381-2016. A 40 mm × 40 mm × 160 mm beam consisted of half of CEA mortars and the other half of OPC mortars. e part with OPC mortar was first formed and cured under standard conditions for 28 d. en, CEA mortar was poured beside OPC mortars, and the samples were placed under standard conditions for a further 3, 7, and 28 d. Figure 3 presents the specimen preparation and testing process of the bond strength test. e results were obtained by dividing the maximum force by the bond area. Two specimens were formed in each group, and the average value was taken.

Mechanical Strength Test.
e flexural strength and compressive strength of CEA mortars at 3 d, 7 d, and 28 d were tested to characterize the mechanical strength of CEA mortars according to Chinese Standard DL/T5126-2001. Prism specimens with a size of 40 mm × 40 mm × 160 mm were used for the flexural strength tests. e blocks that had broken after the flexural strength test were used for the compressive strength test. ree specimens were formed in each group, and the average value was taken.

Toughness Test.
e toughness of CEA mortars was characterized by fracture toughness and impact toughness. e ratio of compressive strength to flexural strength (RCF), a convenient and direct reflection of the fracture toughness of the materials, was determined based on the obtained compressive and flexural strengths [30]. e impact toughness used to reflect the toughness of the cement mortar was evaluated by a self-made dropweight test. is self-made drop-weight test was designed in reference to the drop-weight test recommended by the American Concrete Institute Committee 554 (ACI Committee 544) [31]. A 300 mm × 300 mm × 50 mm mold was used to form OPC mortar, which was placed under standard conditions with a relative humidity of 95% and a temperature of 20 ± 2°C for 28 d. en, CEA mortars with   Figure 4 presents the specimen preparation and testing process of self-made drop-weight test. A steel ball with a mass of 1.835 kg and a diameter of 63.5 mm fell freely from 200 mm to the surface of the specimen. e impact energy absorbed by the specimen, used to reflect the impact resistance, was calculated by equations (2) and (3) according to ACI Committee 544.
ree specimens were formed in each group, and the average value was taken.
where W refers to whole impact energy absorbed by the specimen during the failure process (N·m); ΔW refers to the impact energy absorbed by the specimen after initial cracking (N·m); Δn � n 2 − n 1 ; n 1 refers to the number of impacts until initial cracking occurred; n 2 refers to the number of impacts until specimen failure occurred. Moreover, g refers to the acceleration of gravity (9.8 N/kg); m refers to the mass of the steel ball (1.835 kg); h refers to the drop height of the steel ball (200 mm).

Drying Shrinkage
Test. e drying shrinkage of CEA mortars was tested at 3, 7, 14, 21, 28, and 56 d according to Chinese Standard JC-T603-2004. Prism specimens with a size of 25 mm × 25 mm × 280 mm were used for drying shrinkage tests. Because of the small variation of drying shrinkage of cement mortar, one specimen was tested in each group. e drying shrinkage value of CEA mortars was calculated by equation (4): where S i refers to the drying shrinkage value of the specimen for i days (%); L 0 refers to the initial measurement length of the specimen (mm); L i refers to the measurement length of the specimen after i days (mm); and 250 refers to the effective length of the specimen (mm).

Erosion Resistance Test.
Prism specimens with a size of 40 mm × 40 mm × 160 mm were immersed in erosion solutions (acid solution with 1% hydrochloric acid content or sulfate solution with 5% sulfate content) for 60 d [32]. e mass loss and mechanical strength loss of specimens were calculated by equations (5) and (6), respectively. ree specimens were formed in each group, and the average value was taken: where Δm refers to the mass loss (%); m 0 refers to the dry mass of specimens without immersion (g); m 60 refers to the dry mass of specimens immersed in acid solution or sulfate solution for 60 d (g); ΔR refers to the mechanical strength loss (%); R w refers to the mechanical strength of specimens immersed in water for 60 d (MPa); R 60 refers to the mechanical strength of specimens immersed in acid solution or sulfate solution for 60 d (MPa).

Microstructure
Analysis. Scanning electron microscopy (SEM, S4800) was adopted to observe the microstructure and morphology of several mortars. Samples were broken into small particles and put into anhydrous ethanol to terminate the hydration reaction. A layer of Au powder was plated on the surface of small particle samples. After vacuum treatment, the morphology was observed by SEM.

Results and Discussion
3.1. Bond Strength. Figure 5 presents the flexural bond strength of four types of CEA mortars after 3, 7, and 28 d of curing. e polymer emulsions in CEA mortars tended to penetrate the micropores on the surface of OPC mortar, where they formed a tack coat between CEA mortar and OPC mortar [7]. Larger amounts of polymer emulsions with good flowability permeated into the interface between CEA mortar and OPC mortar at the early ages of CEA mortars. However, the amounts of emulsions permeating into the interface decreased with the gradual hardening of CEA mortars. Figure 5 shows is can be mainly attributed to the good bonding property of EE. Moreover, the active groups in EE could react with Al 3+ or Ca 2+ in cement hydration products and form chemical bridge bonds, which stretched across the interface between CEA mortar and OPC mortar [16,33].
us, partial replacement of EA by EE improves the bond strength of CEA mortars.
To establish the relationship between the proportions of EE replacing EA and the flexural bond strength of CEA mortars, a linear regression was conducted by Origin-Pro 2016 ( Figure 6). A good correlation was found between the proportions of EE replacing EA and the flexural bond strength of CEA mortars. e correlation coefficient R 2 between replacement proportions and flexural bond strength at ages of 3, 7, and 28 d were 0.983, 0.988, and 0.993, respectively. is also indicated that the proportions of EE replacing EA could reflect the bond strength of CEA mortars containing EE.

Mechanical Strength.
e mechanical strength of cement mortars, including flexural strength and compressive strength, reflects the ability of materials to resist stress and strain. Figure 7 presents the flexural strength and compressive strength of four types of CEA mortars after 3, 7, and 28 d of curing.
In Figure 7(a), the flexural strength of CEA mortar-I was the lowest among the four types of CEA mortars, merely reaching 3.4, 4.0, and 5.4 MPa at ages of 3, 7, and 28 d, respectively. is is mainly because EA (with low modulus) lowered the mechanical strength of CEA mortars [34,35]. With increasing proportions of EE replacing EA, the flexural strength of CEA mortars also increased. In comparison with CEA mortar-I, the flexural strength of CEA mortar-IV increased to 4.1, 4.9, and 6.6 MPa at ages of 3, 7, and 28 d, respectively. e variations of compressive strength of CEA mortars with the proportions of EE replacing EA were similar to those observed for flexural strength (Figure 7(b)). e compressive strength of CEA mortar-IV increased to the maximum among all four types of CEA mortars at ages of 3, 7, and 28 d. e content of EA lowering mechanical strength decreased with increasing proportions of EE replacing EA. Moreover, a stronger and denser network structure was formed in CEA mortars because EE (with good bond performance) integrated asphalt and hydration products [16].
us, as a partial replacement of EA, EE improved the mechanical strength of CEA mortars.

Toughness.
e RCF, which conveniently and directly reflects the fracture toughness of materials, was determined based on the obtained compressive strengths and flexural strengths in Section 3.2. Figure 8 presents the RCF of four types of CEA mortars after 28 d of curing. Lower RCF values indicate better fracture toughness. e RCF of CEA mortars decreased slightly with increasing proportions of EE replacing EA. e RCF of CEA mortar-I reached 6.56. Compared with CEA mortar-I, the RCF of CEA mortars-II, III, and IV decreased to 6.48, 6.40, and 6.21, respectively. However, the decreases in RCF were small. e RCF of CEA mortar-IV only decreased by 5.3% compared with that of CEA mortar-I. is indicates that the partial replacement of  To further study the toughness of CEA mortars containing EE, a self-made drop-weight test apparatus was employed to reflect the impact toughness of CEA mortars after 28 d of curing. Figure 9 presents the results of the selfmade drop-weight test. e higher value of impact energy absorbed by the specimens (W) indicates better impact toughness. e W of CEA mortars increased slightly with increasing proportions of EE replacing EA. However, the increases of W were small. e RCF of CEA mortar-IV was highest among all four types of CEA mortars, which only increased by 8.5% compared with that of CEA mortar-I. is indicates that the partial replacement of EA by EE has no obvious effect on the impact toughness of CEA mortars. e evenly dispersed EA membranes were interwoven with cement hydration products and distributed throughout microcracks contained in cement mortars [36,37]. is provided sufficient toughness for CEA mortars to resist crack propagation. ough epoxy resin could form a cross-  Advances in Materials Science and Engineering linking structure with cement hydration products, the brittleness of EE after curing offset the weak cross-linking structure formed by a small amount of EE [17]. us, partial replacement of EA by EE achieves no obvious improvement effect on the toughness of CEA mortars. Interestingly, the impact energy absorbed by specimens after initial cracking (ΔW) decreased with increasing proportions of EE replacing EA. Cured epoxy resin, with its large brittleness, weakened the ability of CEA mortars to continue absorbing energy once cement mortars cracked [16].
is suggests that a large amount of EE may have adverse effects on the toughness of CEA mortars. Figure 10 presents the drying shrinkage of CEA mortars at 3, 7, 14, 21, 28, and 56 d. With increasing curing age, the drying shrinkage for four types of CEA mortars increased. e changing trends of drying shrinkage for four types of CEA mortars were similar. Moreover, the variation rules of drying shrinkage with curing ages for CEA mortars were consistent with the results of Rutherford et al. [38]. e drying shrinkage of CEA mortars increased greatly within 28 d (particularly within the first 7 d) and increased slowly from 28 d to 56 d. is was mainly because of the rapid hydration process, which consumed considerable water in CEA mortars at early ages [38]. It can also be speculated that the hydration process had been completed after 28 d, which could effectively relieve the drying shrinkage of CEA mortars from 28 d to 56 d.

Drying Shrinkage.
Furthermore, the drying shrinkage of CEA mortars decreased with increasing proportions of EE replacing EA. e drying shrinkage of CEA mortar-IV was lowest among the four types of CEA mortars, regardless of the curing age.
is indicates that EE, as a partial replacement of EA, played a role in reducing the drying shrinkage of CEA mortars. is may be because EE, with the preferable bond strength, wrapped around the surface of hydration products, resulting in a stronger interlaced network structure in CEA mortar.
is plays the role of a microfiber, thus restricting particle movement in CEA mortars [38]. Figure 11(a) presents the mass loss and mechanical strength loss of CEA mortars immersed in the acid solution for 60 d. e acid in solution reacts with Ca(OH) 2 in cement mortar, resulting in a decrease of mass and mechanical strength of the CEA mortars [39]. erefore, a smaller value of mass loss and mechanical strength loss indicates better erosion resistance of CEA mortars. e mass loss and mechanical strength loss (flexural strength loss and compressive strength loss) of CEA mortars decreased with increasing proportions of EE replacing EA. e mass loss of CEA mortar-I reached 0.3%. Compared with CEA mortar-I, the mass loss of CEA mortar-IV decreased by 33.3%. In addition, the flexural strength loss and compressive strength loss of CEA mortar-I reached 10.5% and 10.1%, respectively. Compared with CEA mortar-I, the flexural strength loss and compressive strength loss of CEA mortar-IV decreased to 8.2% and 7.4%, respectively. is indicates that EE addition could further improve the erosion resistance of CEA mortars to the acid solution.

Erosion Resistance.
Sulfate in the sulfate solution reacts with calcium aluminate hydrate (CAH) in cement mortars to form ettringite with a volume of about 2.5 times than that of CAH [40]. e internal structure of CEA mortars is destroyed, and the mechanical strength decreases because of the expansion stress caused by ettringite. However, the ettringite attached to the surface of cement mortars will increase their mass. A negative mass loss, as shown in Figure 11(b), indicates an increasing mass of CEA mortars immersed in a sulfate solution. With increasing replacement content of EA by EE, the increase in the mass and the loss of mechanical strength decreased. is indicates that the partial replacement of EA by EE could also further improve the erosion resistance of CEA mortars to the sulfate solution. is is mainly because of the filling of voids in CEA mortars by epoxy resin and the integration of asphalt and hydration products. Moreover,  3.6. Microstructure Analysis. e microstructure of CEA mortar-I (without EE) and CEA mortar-IV (with EE) was characterized by SEM. As presented in Figure 12, asphalt and cement hydration products overlap (Figure 12(a)), forming a stable cement-asphalt structure at the age of 28 d (Figure 12(b)). Moreover, in Figure 12(c), epoxy resin filled the voids in CEA mortars and integrated both asphalt and hydration products to form a strong and dense network structure. With the curing of epoxy resin, CEA mortar formed a stronger, continuously cross-linked network structure at the age of 28 d (Figure 12(d)). It can be inferred that EE plays an important role in improving the performance of CEA mortars with the partial replacement of EA by EE.
e stronger network structure formed in the CEA mortars containing EE can improve the compactness, thus improving the mechanical properties and durability of CEA mortars.

Properties of Cement Emulsified Asphalt Mortars versus
Standard values. As mentioned in Section 1, CEA mortars can be used as repairing materials for cement pavement or cement infrastructures. us, CEA mortars must meet the minimum requirements for repairing materials. Table 6 presents the basic requirements for CEA mortars according to Chinese standard JC/T 2381-2016 e Repairing Mortar, and the obtained test results. e properties of all types of CEA mortars in the test, including flexural bond strength, mechanical strength, toughness, RCF, and drying shrinkage, met the requirements of the standard values. e exception is the flexural strength of CEA mortar-I, which only reached 5.4 MPa at 28 d, remaining below the minimum requirement of 6.0 MPa. is is mainly because of EA, which lowers the mechanical strength of CEA mortars because of its low modulus [34,35].
In addition, a comparison of the test results of CEA mortars-I, II, III, and IV with standard values shows that the partial replacement of EA by EE played a role in enhancing the properties of CEA mortars. Equations (7) and (8) were applied to quantify the improvement degree on the properties of CEA mortars compared with standard values. e results are presented in Figure 13.
where Degree i refers to the improvement degree of CEA mortars for flexural bond strength, flexural strength, and compressive strength (%); Degree j refers to the degree of improvement of CEA mortars for RCF and drying shrinkage (%); V requirementsi and V requirementsj refer to the standard values; and V testi and V testj refer to the test values of CEA mortars. Figure 13 shows that the improvement degree on the properties of CEA mortars increased with increasing the proportion of EE replacing EA. Moreover, the partial replacement of EA by EE exerted the most significant improvement effect on the bond strength of CEA mortars. e bond strength of CEA mortar-IV was enhanced by 115% compared with the standard value. However, the partial replacement of EA by EE had almost no enhancement effect on the toughness of CEA mortars. In summary, when EA was partially replaced by EE, the improvement degree on the properties of CEA mortars ranked as follows: bond strength > compressive strength > compressive strength > drying shrinkage > toughness.

Conclusions
In this study, EA in CEA mortar was partly replaced by EE with additions varying from 0% to 30% (at increments of 10%). e properties of resulting CEA mortars (I, II, III, and IV) were investigated. e following conclusions could be drawn: (1) EE as partial replacement of EA improves the mechanical strength and bond strength of CEA mortars. e mechanical strength and bond strength of CEA mortar-IV increased maximally among all four types of CEA mortars at ages of 3, 7, and 28 d. A good correlation was found between the proportions of EE replacing the EE and the bond strength of CEA mortar.
(2) e partial replacement of EA by EE had no apparent improvement effect on the toughness of CEA mortars. Compared with CEA mortar-I, the RCF of the CEA mortar-IV merely decreased by 5.3%, and the impact energy absorbed by CEA mortar-IV merely increased by 8.3%. Moreover, the impact energy absorbed by specimens after initial cracking decreased with increasing proportions of EE replacing EA. (3) e EE as a partial replacement of EA played a role in improving the drying shrinkage and the erosion resistance of CEA mortars. e drying shrinkage of CEA mortar-IV was lowest among the four types of CEA mortars. e mass loss and mechanical strength loss of CEA mortar-IV immersed in erosion solution were also lowest among the four types of CEA mortars. (4) EE and EA mix well and form a network interpenetrating structure at proportions of EE replacing EA below 30%. e stronger network structure formed in the CEA mortars containing EE improved the compactness and bonding performance between the components of CEA mortars, thus improving the performance of CEA mortars.
Based on the above properties, the partial replacement of EA by EE is suggested to enhance the properties of CEA mortars.

Future Work
In the future work, the hardening mechanism and microstructure of CEA mortars containing EE will be studied. Moreover, the reaction principle of EE in CEA mortars will be further assessed.

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest
e authors declare that there no conflicts of interest regarding the publication of this article.

Acknowledgments is work was supported by the Western Transportation Construction
Science and Technique Program (2013318J09230) and the Natural Science Foundation of Qinghai Province (no. 2020-ZJ-736).