Multihazard Response Control of Base-Isolated Buildings under Bidirectional Dynamic Excitation

-e issues of safety and posthazard functionality of structures under multihazard scenarios are some of the significant challenges in the current dynamic and rapidly growing urban environment. In this paper, multistory base-isolated buildings are investigated under the independent multihazard scenario of earthquake and blast-induced ground motion (BIGM). Multistory building models equipped with five different types of isolation systems, namely, the laminated rubber bearing (LRB), lead-rubber bearing (N-Z system), pure friction (PF) system, friction pendulum system (FPS), and resilient-friction base isolator (R-FBI) are assessed under bidirectional multihazard excitations. -e suitability of the isolation systems and their key parameters in protecting multistory buildings is evaluated. Furthermore, the influence of the superstructure characteristics, such as the superstructure damping and the number of stories, is also assessed.-e effect of bidirectional hazards on fixed-base buildings is also presented for comparison. -e key response quantities of base-isolated buildings are presented and compared for different isolation systems. Parametric investigations are also conducted, and the trends of the response quantities are presented to study the influence of important parameters of isolation systems in protecting the buildings under the multihazard scenario of earthquake and BIGM. -e results of the investigation show that the behaviors of the buildings equipped with various isolation systems are different for the two hazards. Moreover, the influences of the key parameters of the isolation systems are found to be different for various hazards.-erefore, the selection of design parameters of isolation systems shall be made with due consideration of the influence of multiple hazards. Additionally, the influence of the properties of the superstructure, such as the number of stories and the damping of the superstructure, on the behavior of the base-isolated buildings under the multihazard loading, is presented.


Introduction
Earthquakes have been and remain to be one of the prominent threats to the safety and serviceability of civil engineering structures and infrastructure systems. Numerous strategies have been proposed, researched, and implemented for seismic protection of structures [1][2][3][4]. e use of structural response control strategies has been proven to be an effective approach. Base isolation is an effective strategy to protect structures, the inhabitants of the structures, and the contents housed within the structures against the undesirable effects of earthquakes. It reduces the earthquake force imparted on the superstructure by increasing the fundamental time period of the structure and dissipating the earthquake energy [5,6]. Various types of base isolation strategies, such as the elastomeric type bearings, sliding bearings, and rolling bearings, have been proposed [6]. Also, different active and semiactive seismic isolation strategies have attracted researchers' attention in recent years [7][8][9][10].
Structures, including those equipped with base isolation systems, are also likely to be subjected to other hazards in their service life, which necessitates the consideration of various types of loadings in the design of structures. Despite the significant socioeconomic impact caused by various natural and human-made hazards [11,12], such as blast, impact, earthquake, tsunami, and wind, less attention is devoted on research and development to understand the behavior of structures under multiple hazards and to devise design strategies thereof. Additionally, the risk associated with the reduced safety and serviceability of key infrastructures, categorized as lifeline structures, such as hospitals, bridges, power plants, data centers, and communication centers, is paramount. erefore, it is crucial to design structures, especially the critical infrastructures, by considering all the hazards likely to affect safety and serviceability. ere is limited research on the use of the multihazard approach in the performance assessment and design of structures. For instance, Messervey et al. [13], Gardoni and LaFave [12], Mahmoud and Chulahwat [14], Venanzi et al. [15], and Roy and Matsagar [16,17] have conducted studies on the multihazard protection of structures.
Although base isolation is an effective strategy to mitigate the adverse effects of earthquakes, its efficacy in protecting structures under multihazard loading is not explored adequately. Most of the studies on the base-isolated structures also focus on earthquake protection, and therefore, there are limited studies that are conducted on the performance assessment of base-isolated structures under other hazards, such as wind and blast. Some of the attempts to investigate the behavior of base-isolated structures under wind loading include the studies conducted by Henderson and Novak [18,19]. ey have conducted theoretical and experimental studies to assess the response of the baseisolated buildings under wind loading, wherein the theoretical and experimental results are compared. Chen and Ahmadi [20] have evaluated the sensitivity of structures isolated by the laminated rubber bearing (LRB), high damping rubber bearing (HDRB), and resilient-rubber bearing (R-FBI) to wind loading. Furthermore, Kareem [21] has studied the dynamic response of base-isolated buildings with passive dampers under wind loading. Later, Liang et al. [22] have assessed the habitability of base-isolated buildings under fluctuating wind load. Recently, a probabilistic investigation on the response of tall base-isolated buildings under wind loading has been reported by Feng and Chen [23]. e response of base-isolated structures under surface blast has been assessed by some researchers. Zhang and Phillips [24,25] have studied the performance of a multistory base-isolated building with and without passive supplemental dampers in suppressing the vibration response of the building exposed to blast loading. Also, Kangda and Bakre [26] have assessed the response of base-isolated structures subjected to surface blast and concluded that base isolation could be effective in mitigating the blast response quantities, such as the peak story displacement, story drift, and root mean square (RMS) absolute acceleration. e performance of baseisolated buildings under blast-induced ground motion (BIGM) has also captured attention in the recent times. Mondal et al. [27,28] have studied the response of buildings isolated by lead-rubber bearing (N-Z system) under BIGM. Further, the performance of a base isolation system equipped with shape-memory alloy in protecting buildings under BIGM has been studied by Mondal et al. [29]. Furthermore, the use of various base isolation systems in protecting buildings against blast-induced ground motions has been discussed by Mondal et al. [30]. e findings of the investigations reveal that base isolation can be beneficial to control the vibration response of buildings under blast-induced ground motions. e performance of base isolation strategies for the vibration response control of buildings under other nonseismic hazards, such as train-induced vibrations, has also been explored [31][32][33]. e available limited literature on the implementation of base isolation for the vibration response control of buildings under different types of excitations indicate the potential benefit of the strategy in mitigating the adverse effects of various types of hazards. Notwithstanding the vibration protection potential of base isolation systems, base-isolated buildings could be influenced differently under distinct types of hazards. erefore, it is necessary to consider the multihazard approach to satisfy safety and serviceability design requirements for base-isolated buildings that are likely to be subjected to different types of loading. However, there are no studies which investigate the behavior of baseisolated buildings subjected to both earthquakes and blast-induced ground motions. In addition, the influence of the key parameters of the base isolation systems on the efficacy of the response mitigation under the multihazard scenario of earthquake and BIGM has not been explored. erefore, it would be essential to investigate and unveil the performance of buildings equipped with the laminated rubber bearing (LRB), lead-rubber bearing (N-Z system), pure friction (PF) system, friction pendulum system (FPS), and resilient-friction base isolator (R-FBI) under the multihazard scenario of earthquake and blast-induced ground motion. Consequently, the behavior of buildings equipped with various base isolation systems is assessed under multihazard loading in this paper. e main objectives of this study include the following: (a) to assess the performance of base-isolated buildings under bidirectional near-fault (NF) earthquake ground motions, far-fault (FF) earthquake ground motions, and blast-induced ground motions (BIGMs), (b) to evaluate the effect of the characteristic parameters of the five base isolation systems, considered herein, on the behavior of base-isolated buildings under different hazards, and (c) to study the effect of the properties of the superstructure on the multihazard response of baseisolated buildings.

Modeling of a Base-Isolated Building under
Bidirectional Excitation e schematic diagram and idealized model of the baseisolated building considered in this investigation are depicted in Figure 1. e three-dimensional model of the base-isolated building portrayed in the figure shows the orientation of the building, the location of the isolators, the superstructure properties, and the base excitation. e mathematical modeling of the base-isolated building 2 Shock and Vibration under bidirectional base excitation is described as follows.

Governing Equations of Motion.
e governing equations of motion of the base-isolated building, subjected to ground acceleration, are derived under the assumption that the superstructure remains in the elastic range. Furthermore, it is considered that the floors are infinitely rigid, the beams and columns are axially inextensible, the building is symmetric in both X and Y directions, and the torsional response of the building is neglected. Accordingly, two degrees of freedom, lateral displacements in X and Y directions, at each floor and base mass levels are considered in the formulation of the equations of motion. e matrix form of the governing equations of motion of the base-isolated building under bidirectional base excitation is given as where M, C, and K, respectively, are the mass, damping, and stiffness matrices of the base-isolated building. ese structural property matrices are given as where M s � diag[m 1 , m 2 , . . . , m j , . . . , m N ] is the superstructure mass matrix of size N; N is the number of stories; m j is the mass of the j th floor; m b is the base mass; C sx and K sx , respectively, are the damping and the stiffness matrices of the superstructure in the X direction; C sy and K sy , respectively, are the damping and the stiffness matrices of the superstructure in the Y direction; c 1x and c 1y are the damping constants of the first story of the building in X and Y directions, respectively; k 1x and k 1y are the stiffnesses of the first story of the building in X and Y directions, respectively; r b � 1, 0, 0, . . . , 0 { } is a row vector of size N; 0 � 0, 0, . . . , 0 { } is a row vector of size N; and 0 is a null matrix of size N × N.
Furthermore, the vectors of displacements, velocities, and accelerations of the base-isolated building, X, _ X, and € X, respectively, the vector of the restoring forces in the isolator, f, the vector of ground accelerations, € U g , and the matrix of influence coefficients, r, are given as follows.
where x b and y b , respectively, are the displacements of the base mass relative to the ground in X and Y directions; _ x b and _ y b , respectively, are the velocities of the base mass relative to the ground in X and Y directions; € x b and € y b , respectively, are the accelerations of the base mass relative to the ground in X and Y directions; X s � x 1 , x 2 , . . . , x N T and Y s � y 1 , y 2 , . . . , y N } T , respectively, are the vectors of floor displacements in X and Y directions; _ X s and _ Y s , respectively, are the vectors of floor velocities in X and Y directions; € X s and € Y s , respectively, are the vectors of floor accelerations in X and Y directions; f bx and f by , respectively, are the X and Y components of the force acting on the base isolators; € x g and € y g are the ground accelerations in X and Y directions, respectively; and r � 1, 1, . . . , 1 { } T is a column vector of influence coefficients of size N. e solution of the governing equations of motion is obtained numerically using state-space formulation.

Mathematical Modeling of Base Isolators under Bidirectional Excitation.
In this study, the multihazard response of multistory buildings isolated by elastomeric and sliding bearings are studied. Two elastomeric bearings, the laminated rubber bearing (LRB) and lead-rubber bearing (N-Z system), are used; whereas, the three types of sliding bearings investigated are the pure friction (PF) system, friction pendulum system (FPS), and resilient-friction base isolator (R-FBI). e mathematical modeling of the base isolation bearings is realized by considering their characteristic parameters. e LRB is mathematically represented using the isolation time period (T b ) and the isolation damping ratio (ξ b ), whereas the N-Z system is modeled using the isolation time period (T b ), the isolation damping ratio (ξ b ), the yield displacement (q), and normalized yield strength (F 0 ). e PF system is characterized using the friction coefficient (μ b ), and the isolation time period (T b ) and the friction coefficient (μ b ) are used to model the FPS. Furthermore, the isolation time period (T b ), the friction coefficient (μ b ), and the isolation damping ratio (ξ b ) are used to model the R-FBI. e LRB is a linear isolation system, and the restoring forces of the bearing in X and Y directions can be obtained as where is the angular frequency of the isolation system; and M t � m b + N j�1 m j is the total mass of the base-isolated building. e N-Z system, PF system, FPS, and R-FBI are nonlinear isolators, and their force-deformation behaviors are mathematically modeled with and without considering the bidirectional interaction. e restoring forces in the isolation system acting in X and Y directions, respectively, can be obtained as where k i � F y /q is the initial stiffness of the isolator and α � k b /k i is the postyield to preyield stiffness ratio of the isolator. Furthermore, the nondimensional hysteretic displacement components, h x and h y , are evaluated using a set of nonlinear differential equations proposed by Wen [34,35] and Park et al. [36], respectively, for hysteretic behavior without and with bidirectional interaction. Without accounting for the bidirectional interaction, the values of h x and h y can be obtained using the following equations: On the contrary, considering the bidirectional interaction, h x and h y can be evaluated based on the following equation: where n � 2 is a parameter used to characterize the smoothness of the nonlinear force-deformation curve of the  respectively, are given as 1, 0.5, and 0.5 for the N-Z system [37]; whereas, the values of A, β, and τ, respectively, are given as 1, 0.1, and 0.9 for the PF system, FPS, and R-FBI [38]. Also, the value of the yield displacement, q, is taken as 2.5 cm for the N-Z system [39], whereas q � 0.25 mm is used for sliding isolation systems. Additionally, the damping ratio of the PF system, the postyield stiffness of the PF system, and the damping ratio of the FPS are taken as 0. e yield strength of the N-Z system is evaluated as F y � F 0 W t , where F 0 and W t , respectively, are the normalized yield strength of the isolation bearing and the total weight of the base-isolated building. e yield strength of the PF system, FPS, and R-FBI is evaluated as F y � μ b W t , where μ b is the friction coefficient of the isolation system.

Numerical Study
Base-isolated buildings are studied under bidirectional multihazard excitations. e buildings are isolated using five types of base isolation systems, and the behavior of the isolated buildings is assessed under near-fault (NF) earthquakes, far-fault (FF) earthquakes, and blast-induced ground motion (BIGM). e schematic diagram and the idealized model of the base-isolated building studied in this paper are portrayed in Figures 1(a) and 1(b). e masses of all the floors of the building and the base mass are considered to be equal (m j � m b � m). Also, the lateral stiffnesses of all stories are equal for both X and Y directions. e Rayleigh method is used to construct the damping matrix of the superstructure where the damping ratio of the superstructure (ξ s ) is considered to be 5%. Five building models having different number of stories are studied. e different values of the number of stories of the five buildings are 1, 2, 4, 6, and 8; whereas the fundamental time period (T) values for fixedbase buildings are 0.1 s, 0.2 s, 0.4 s, 0.6 s, and 0.8 s, respectively. Furthermore, the story height (H) of 3.5 m is considered for all the buildings. A summary of the properties of the superstructure and five base isolation systems used in this study is presented in Table 1.
In numerical investigations, the performances of the buildings equipped with five base isolation systems are assessed by studying different response quantities under NF earthquakes, FF earthquakes, and BIGMs. e response quantities, in X and Y directions, that are evaluated and studied include the absolute top floor accelerations ( € x N and € y N , respectively); top floor displacements (x N and y N , respectively), relative to the ground; isolator displacements (x b and y b , respectively), relative to the ground; normalized base shears (V n x and V n y , respectively); total superstructure drift ratio (Δ x total and Δ y total , respectively); and maximum interstory drift ratio (Max(Δ x j ) and Max(Δ y j ), respectively). e total superstructure drift ratio is obtained as the ratio of the total drift of the superstructure to the total height of the superstructure. Furthermore, the maximum interstory drift ratio is obtained as the maximum of the peak values of the interstory drift ratios of all the stories of the building. In addition, resultant top floor acceleration , and resultant maximum interstory drift ratio (Max(Δ σ j )) are also studied.

Bidirectional Multihazard Condition Considered in the
Study. e current study focuses on the investigation of the multihazard behavior of base-isolated buildings under bidirectional base excitations of different types. e near-fault (NF) earthquake ground motions, far-fault (FF) earthquake ground motions, and blast-induced ground motions (BIGMs) are imparted on buildings isolated using various   Table 2 provides the date of the event, the recording station, the closest distance to rupture plane, the peak ground acceleration (PGA) in gravitation acceleration (g) unit, and other relevant details of the earthquake ground motion data. In the table, the two components of each of the six earthquake events are presented, which are applied as base excitations in the X direction ( € x g ) and Y direction ( € y g ) simultaneously. e extent of ground vibration due to blast is influenced by various parameters, such as the type of the explosive, the weight of the explosive, the type of the ground medium, and the distance to the charge. In this study, the blast-induced ground motion is represented mathematically using the function proposed by Carvalho and Battista [40]. e exponentially decaying BIGM acceleration, € U g (t), that is imparted on the base-isolated buildings with an angle of attack (θ) measured from the X-axis (Figure 1(c)) can be evaluated as where t is the time instant; t d � R/C p is the arrival time; R is the distance to the charge; _ u g � 0.3607(Q/V) 0.2872 (R/Q (1/3) ) −1.3375 is the peak particle velocity (PPV) [41]; C p � ��� E/ρ is the velocity of wave propagation through the soil medium; E and ρ, respectively, are Young's modulus and the average density of the soil medium; V is the charge chamber volume in m 3 ; and Q is the weight of the equivalent trinitrotoluene (TNT) charge in kg.
e values of C p , R, and V used in this study are 5280 m/s, 50 m, and 1000 m 3 , respectively, whereas the TNT charge weight (Q) values of 50 t, 75 t, and 100 t are considered to evaluate BIGM acceleration. Additionally, the obtained BIGM acceleration is applied to the base-isolated buildings with angle of attack (θ) values of 0°, 15°, 30°, and 45°. For BIGM acceleration acting with an angle of attack θ from the X-axis, the X component of BIGM can be obtained as . e time histories of the near-fault earthquakes, far-fault earthquakes, and BIGMs used in the study are presented in Figure 2, whereas the Fourier spectra of the three types of excitations are given in Figure 3.

Effect of Bidirectional Interaction.
e two components of the considered earthquake ground motions and BIGMs are applied to the building as base excitations acting in X and Y directions simultaneously. e resultant response quantity can then be evaluated as ψ r � where ψ r is the resultant value of any response quantity, ψ X is the value of the response quantity in the X direction, and ψ Y is the value of the response quantity in the Y direction.
For the linear base isolation system, laminated rubber bearing (LRB), the response of the building under bidirectional excitations can be obtained by evaluating the response of the building under the two components of the excitations applied in X and Y directions without special consideration of the bidirectional interaction at the isolation level. However, this approach may lead to incorrect results for the buildings isolated by nonlinear base isolation systems. When buildings isolated by nonlinear base isolators are subjected to bidirectional excitations, the force that is acting on the base isolators is derived from the excitations acting in both X and Y directions. erefore, when the resultant force in the isolator equals the yield force, the postyield behavior of the isolation system is activated. e X and Y components of the yield strength of the isolator are influenced by relative magnitudes of the isolator forces in X and Y directions. e relationship between the normalized yield strength (F 0 ), the normalized yield strength in the X direction (F X 0 ), and the normalized yield strength in the Y direction (F Y 0 ) is given as e graphical representation of relationship between F X 0 , F Y 0 , and F 0 is depicted in Figure 4, as a function of the angle (direction) of the resultant isolator force measured from the X-axis (φ).

Shock and Vibration
If the response of the building is evaluated independently for excitations acting in X and Y directions, it results in neglecting the effect of the bidirectional interaction. For example, the response of a four-story building with a fixed-base fundamental time period (T) of 0.4 s and a superstructure damping ratio (ξ s ) of 0.05 isolated by the FPS is presented in Figures 5 and 6. In Figure 5, the time histories of the top floor acceleration of the four-story building isolated by the FPS (T b � 2.5 s and μ b � 0.1) with and without the consideration of bidirectional interaction are presented. Furthermore, the forcedeformation plots of the FPS, with and without the consideration of bidirectional interaction under (a) LP1989, (b) LP1989F, and (c) BIGM, Q � 75 t and θ � 30°, are shown in Figure 6. e time history plots and the force-deformation behavior depicted in Figures 5 and 6 show that the response obtained with and without the consideration of the bidirectional interaction are significantly different.
erefore, a detailed comparative study is conducted for determining the degree to which the values of the different response quantities of base-isolated buildings are influenced due to the bidirectional interaction. e response quantities of the buildings isolated by the N-Z system, PF system, FPS, and R-FBI are studied under various bidirectional base excitations with and without the consideration of the bidirectional interaction. e percentage variation between the response quantities of the building with and without the consideration of the bidirectional interaction is evaluated as

Shock and Vibration
where Δψ is the percentage difference in a response quantity; ψ NoInt is the peak value of the resultant response quantity when the bidirectional interaction is not considered; and ψ Int is the peak value of the resultant response quantity when the bidirectional interaction is considered. e values of Δψ corresponding to the resultant top floor acceleration, resultant isolator displacement, and resultant base shear of the four-story building equipped with four nonlinear isolators under NF earthquakes, FF earthquakes, and BIGMs are presented in Figure 7. It is shown in the figure that, for all cases, the resultant top floor acceleration and the resultant base shear are overestimated if the bidirectional interaction is neglected. On the contrary, the neglection of the bidirectional interaction is observed to result in the underestimation of the resultant isolator displacement response. e underestimation and overestimation of the response quantities arise because of the modeling approach that neglects the bidirectional interaction. When the bidirectional interaction is neglected, the isolation system is modeled in a way such that the postyield behavior is exhibited at a larger value of the normalized resultant isolator force than that of the case where the bidirectional interaction is considered. is results in the modeling of the isolation system with increased initial stiffness and reduced flexibility under bidirectional excitations. Consequently, a smaller value of resultant isolator displacement and larger values of resultant top floor acceleration and resultant base shear are obtained for the case where the bidirectional interaction is not considered. e extent of the overestimation and underestimation of the response quantities varies depending on the excitation and the isolation system. For NF earthquake ground motions, the neglection of the bidirectional interaction results in the overestimation of the resultant top floor acceleration and the resultant base shear by up to 44.5% and 31.9%, respectively. On the contrary, the resultant isolator displacement is underestimated by up to 32%. For FF earthquakes, the neglection of the bidirectional interaction resulted in the overestimation of the resultant top floor acceleration and the resultant base shear by up to 31.6% and 33.5%, respectively. Also, the resultant isolator displacement is underestimated by up to 81.2%. e resultant top floor acceleration and the resultant base shear are overestimated by up to 29.3% due to the neglection of the bidirectional interaction for the base-isolated buildings exposed to BIGMs. Furthermore, the resultant isolator displacement is underestimated by up to 27.6%. Consequently, it can be concluded that, when the bidirectional interaction is neglected, the resultant top floor acceleration and resultant base shear are overestimated, and the resultant isolator displacement is underestimated considerably under all three types of excitations.
is influences the multihazard response of the base-isolated buildings significantly. erefore, the bidirectional interaction should be considered to capture the behavior of base-isolated buildings under bidirectional NF earthquakes, FF earthquakes, and BIGMs with adequate accuracy.

Multihazard Response of Base-Isolated Buildings under
Bidirectional Excitations. Four-story base-isolated buildings are studied under NF earthquakes, FF earthquakes, and BIGMs to understand the effect of the various base isolation systems on the behavior of the buildings under multihazard loading. e base-isolated buildings are subjected to bidirectional excitations, and their response quantities in X and 0°6 0°3 0°0°F igure 4: e relationship between the normalized yield strength of the isolator (F 0 ) and its components in X and Y directions (F X 0 and F Y 0 , respectively) for different directions (angle, φ, measured from the X-axis) of the resultant isolator force.
Y directions and the resultant response quantities are investigated considering the bidirectional interaction. e bidirectional response of the base-isolated building under BIGMs with different values of equivalent TNT charge weight (Q) and the angle of attack (θ) is also presented. e influence of Q on the response quantities is observed from the results obtained for BIGMs with a 30°angle of attack and equivalent TNT charge weight (Q) values of 50 t, 75 t, and 100 t. As expected, the response quantities are observed to be more for the higher value of TNT charge weight. In addition, the influence of the angle of attack is studied by taking BIGMs with 75 t equivalent 10 Shock and Vibration TNT charge weight and angle of attack (θ) values of 0°, 15°, 30°, and 45°. As the angle of attack increases, the response in the Y direction is observed to be increasing and the same in the X direction is observed to be decreasing. is is primarily because the building is symmetrical about X and Y axes, and the component of BIGM along the Y direction increases with an increasing angle of attack. e results presented in Figure 8 show that the top floor acceleration and isolator displacement response   To investigate the behavior of the base-isolated buildings further, under the multihazard scenario of earthquake and BIGM, the top floor acceleration, top floor displacement, isolator displacement, normalized base shear, total superstructure drift ratio, and maximum interstory drift ratio are evaluated under bidirectional NF earthquakes, FF earthquakes, and BIGMs. e X, Y, and resultant components of the response quantities are assessed for the buildings equipped with the N-Z system, LRB, PF system, FPS, and

12
Shock and Vibration   .. e average values of the response quantities obtained under IV1979, LP1989, and NR1994 earthquake ground motions are taken to obtain representative trends for the NF earthquake case. Similarly, the average values of the response quantities obtained under IV1979F, LP1989F, and NR1994F earthquake ground motions are taken to obtain representative trends for the FF earthquake case. e average response trends are obtained for the buildings isolated by the five base isolation systems under NF and FF earthquakes, which are then compared with the response trends obtained for the base-isolated buildings subjected to BIGM. e comparison of the performance of the N-Z system (T b � 2.5 s and q � 2.5 cm) under NF earthquake, FF earthquake, and BIGM is depicted in Figure 9 for the four-story building (T � 0.4 s and ξ s � 0.05). e effect of the normalized yield strength (F 0 ) of the N-Z system on the resultant top floor acceleration (€ σ N ), resultant top floor displacement (σ N ), resultant isolator displacement (σ b ), resultant normalized base shear (V n σ ), resultant total superstructure drift ratio (Δ σ total ), and resultant maximum interstory drift ratio (Max(Δ σ j )) is presented. e trends of the six response quantities obtained for the N-Z system with different isolation damping ratio e influence of the isolation damping ratio on the response quantities of the four-story base-isolated building for the three types of excitations is depicted in Figure 10. e trends of the resultant top floor acceleration, resultant top floor displacement, resultant isolator displacement, resultant normalized base shear, resultant total superstructure drift ratio, and resultant maximum interstory drift ratio observed under earthquake excitation, for an increase in the isolation damping ratio, are similar. e values of the six response quantities reduce with an increase in the isolation damping ratio both under NF and FF earthquakes. For the building subjected to BIGM, the resultant normalized base shear, resultant total superstructure drift ratio, and resultant maximum interstory drift ratio show a relatively flat trend with an increase in the isolation damping ratio. On the contrary, an increase in the isolation damping ratio results in the reduction of the igure 8: e response of a four-story building isolated by the N-Z system under NF earthquakes, FF earthquakes, and BIGMs. resultant top floor displacement and resultant isolator displacement, whereas the resultant top floor acceleration increases with an increase in the isolation damping ratio.

Response of the Building Isolated by the PF System.
e performance of the PF system under NF earthquake, FF earthquake, and BIGM is evaluated by varying the friction coefficient of the isolation system (μ b ) from 0.025 to 0.25. e influence of the friction coefficient of the isolation system on the response quantities of the fourstory base-isolated building under the three types of excitations is presented in Figure 11. e results plotted in the figure show that the trends of the six response quantities are similar for NF earthquakes, FF earthquakes, and BIGMs. For all the three types of excitations, the top floor displacement and isolator displacement show a decreasing trend for an increase in the friction coefficient. Moreover, as the friction coefficient of the PF system increases, the top floor acceleration, base shear, total superstructure drift ratio, and maximum interstory drift ratio increase. Also, the comparison of the residual resultant isolator displacements of the building equipped with the PF system to that of the other isolation systems is presented in Table 3. Because the pure friction system lacks restoring capacity, the building isolated by the PF system is observed to be prone to large residual displacements under the three types of excitations.

Response of the Building Isolated by the FPS.
e behavior of the four-story building isolated by the FPS under the independent multihazard scenario of earthquake and BIGM is presented in Figure 12  friction coefficient values beyond 0.05, the trends are reversed, and the three response quantities increase with an increase in μ b . Moreover, an increase in μ b results in a consistent increment of the resultant normalized base shear, resultant total superstructure drift ratio, and resultant maximum interstory drift ratio of the base-isolated building under BIGM.

Response of the Building Isolated by the R-FBI.
e performance of the four-story building equipped with the R-FBI under NF earthquake, FF earthquake, and BIGM is portrayed in Figure 13. e isolation time period (T b ) of the R-FBI is taken as 2.5 s; the isolation damping ratio (ξ b ) values of 0.05, 0.075, 0.1, 0.125, and 0.15 are considered; and the coefficient of friction of the isolation system (μ b ) is varied from 0.025 to 0.2. e overall behavior of the building isolated by the R-FBI is similar to that of the building equipped with the FPS, except for a small difference in the trends of the resultant normalized base shear, resultant total superstructure drift ratio, and resultant maximum interstory drift ratio under FF earthquakes. For the building equipped with the R-FBI subjected to FF earthquakes, an increase in the friction coefficient of the isolation system results in a consistent increment of the resultant normalized base shear, resultant total superstructure drift ratio, and resultant maximum interstory drift ratio.
For the building subjected to NF earthquakes, the top floor displacement, isolator displacement, normalized base shear, total superstructure drift ratio, and maximum interstory drift ratio are influenced significantly by the damping ratio of the R-FBI. For small values of the friction coefficient of the isolator, a larger isolation damping ratio results in smaller values of the five response quantities. However, as the friction coefficient of the R-FBI increases, the influence of the damping ratio of the isolation system diminishes. Moreover, the effect of the damping ratio of the R-FBI on the top floor acceleration is less under NF earthquakes, irrespective of the value of the friction coefficient. Under FF earthquakes, the top floor acceleration, normalized base shear, total    influence on the values of the isolator displacements of the buildings isolated by the LRB, N-Z system, PF system, FPS, and R-FBI under three types of excitations. e influence of the relative flexibility of the superstructure in X and Y directions is also studied. e ratio of the lateral stiffness of the columns of each story of the building in the Y direction to that of the X direction (k j,Y /k j,X ) values of 1, 1.2, 1.4, 1.6, and 1.8 is considered. A four-story base-isolated building with a fixed-base fundamental time period of 0.4 s, in the X direction, is studied by using the different values of k j,Y /k j,X , under the multihazard scenario of earthquakes (NF earthquake and FF earthquake) and BIGMs. e trends of the resultant top floor acceleration and resultant isolator displacement of four-story base-isolated buildings with different values of k j,Y /k j,X are depicted in Figure 15. e figure shows that the values of the resultant isolator displacements are not influenced significantly by k j,Y /k j,X for the buildings isolated by the LRB, N-Z system, PF system, FPS, and R-FBI under three types of excitations. Also, a larger value of k j,Y /k j,X is observed to result in a reduced value of resultant top floor acceleration, especially for the buildings subjected to BIGM. However, the trends of the resultant top floor acceleration and the resultant isolator displacement obtained for different values of k j,Y /k j,X are the same. erefore, it can be concluded that the relative flexibility of the superstructure in X and Y directions does not influence the behavior of the symmetrical building under NF earthquakes, FF earthquakes, and BIGMs. e effect of the damping of the superstructure is evaluated by investigating the response of the four-story base-isolated building considering ξ s values of 2%, 3.5%, 5%, 6.5%, and 8%. It may be worth mentioning that small structural damping ratio (i.e., 2% or 3.5%) may not be feasible for fixed-base multistory buildings when nonlinear deformation is considered. However, for base-isolated buildings, small values of superstructure damping can reasonably be considered because the superstructure is prominently expected to behave elastically. e resultant top floor acceleration and resultant isolator displacement of the building isolated by the LRB, N-Z system, PF system, FPS, and R-FBI, under NF earthquake, FF earthquake, and BIGM, are obtained, and the trends are plotted in Figure 16. It is observed that superstructure damping does not affect the trends of the resultant top floor acceleration and resultant isolator displacement of the buildings isolated by four base isolation systems. Additionally, it is observed that the superstructure damping ratio does not influence the value of the isolator displacement for the buildings isolated by five base isolation systems under all three types of dynamic base excitations. However, although the trends of the top floor acceleration are the same, the results presented in Figure 16 show that a larger superstructure damping ratio typically results in a smaller value of top floor acceleration. erefore, based on the observations, it can be concluded that the superstructure characteristics have less influence on the behavior of the base-isolated buildings under the multihazard loading scenario of earthquakes (NF earthquakes and FF earthquakes) and BIGMs, as compared to the properties of the base isolators.

Conclusions
is study presents an investigation of the behavior of multistory buildings isolated by various types of elastomeric and sliding base isolation systems under multihazard loading. e multihazard scenario of earthquakes (near-fault and far-fault earthquake) and blast-induced ground motion (BIGM) is considered, wherein the bidirectional effects of the hazards are taken into account. e influence of the selection of different values of the parameters of isolators on the key response quantities of the buildings, such as the top floor acceleration, top floor displacement, isolator displacement, base shear, interstory drift ratio, and total superstructure drift ratio, are assessed under the multihazard scenario. Furthermore, the influence of the properties of the superstructure (superstructure flexibility and superstructure damping ratio) on the behavior of the baseisolated buildings under multihazard loading is assessed. Based on the findings of the extensive numerical studies, it is concluded that base-isolated buildings behave differently under the near-fault earthquake, far-fault earthquake, and blast-induced ground motion. Consequently, the design of the isolation systems and the selection of suitable parameters thereof shall be done cautiously, accounting for the effects of both types of hazards considered on the buildings. e specific conclusions of the study are listed as follows: (1) Although the base isolation technology can help in protecting buildings from three types of dynamic base excitations (NF earthquakes, FF earthquakes, and BIGMs), the base-isolated buildings behave differently under different multiple hazards. (2) e response quantities of the base-isolated buildings obtained with and without the consideration of bidirectional interaction are significantly different. e resultant isolator displacement is

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest
e authors declare that they have no conflicts of interest.