Deviatoric Stress Evolution Laws and Control in Surrounding Rock of Soft Coal and Soft Roof Roadway under Intense Mining Conditions

Aiming at the problem of large deformation and instability failure and its control of soft coal and soft roof roadway under intense mining, laboratory experiments, theoretical calculations, Flac numerical simulation, borehole peeping, and pressure observation were used to study the deflection characteristics of the deviatoric stress of the gas tailgate and the distribution and failure characteristics of the plastic zone in the mining face considering the strain softening characteristics of the roof and coal of roadway, and then the truss anchor cable-control technology is proposed. +e results show the following: (1) +e intense mining influence on the working face will deflect the peak deviatoric stress zone (PDSZ) of the surrounding rock of the gas tailgate. +e influence distance of PDSZ is about 20m in advance and 60m in lag; the PDSZ at the gob side of the roadway is located in the range of 3–5.5m from the surface of the coal pillar, while the coal wall side is mainly located in the range of 3–4.5m at the shoulder corner and bottom corner of the solid coal. (2) +e intense mining in the working face caused the nonuniform expansion of the surrounding rock plastic area of the gas tailgate. +e two shoulder angles of the roadway and the bottom of the coal pillar have the largest damage range, and the maximum damage location is the side angle of the coal pillar (5m). Angle and bottom angle of coal pillar are the key points of support control. (3)+e plastic failure line of the surrounding rock of the gas tailgate is always between the inner and outer contours of the PDSZ, and the rockmass in the PDSZ is in a stable and unstable transition state, so the range of anchor cable support should be cross plastic failure line. (4) +e theoretical calculations and numerical simulation results agree well with the drilling peep results. Based on the deflection law of the PDSZ and the expansion characteristics of the plastic zone, a truss anchor cable supporting system with integrated locking and large-scale support function is proposed to jointly control the roof and the two sides, which effectively solves the problem of weak surrounding rock roadway under severe mining deformation control problems realizing safety and efficient production in coal mines under intense mining.


Introduction
e influence of mining is a major difficulty regarding the rock stability of the surrounding roadway in a mining area and is a popular research topic. Most roadways or chambers are unaffected by mining disturbances in the coal face [1]. Many roadways have achieved stability control of the surrounding rock during excavation. However, large deformations of the surrounding rock, serious floor heaving, and uncontrollable deformations of the surrounding rock still occur due to mining disturbances. e roadway is often seriously deformed and needs to be maintained and repaired frequently. us, the problem of roadway maintenance has affected the normal production and economic benefits of coal mines.
Experts and scholars have conducted several theoretical and experimental studies on the deformation and failure mechanism of the surrounding rock and the corresponding supporting control technology when under the influence of mining. Based on the engineering background of a multiroadway layout in a mining face, Kang et al. [2] analyzed the deformation and stress distribution characteristics of the surrounding rock of a retained roadway and determined that a deformation of this surrounding rock mostly occurs after the creation of a mining face. Wang et al. [3] studied the deformation and failure mechanism of the surrounding rock of a roadway under the influence of mining, and they considered that the advancement of an abutment pressure has a significant influence on the stress distribution of the surrounding rock. In addition, Li et al. [4] studied the failure characteristics of a dynamic long-span pressure mining roadway and found that the main cause of a support failure is the comprehensive effect of a complex surrounding rock environment. Moreover, Zhang et al. [5] established a mechanical model of a nonisobaric roadway and discussed the evolution mechanism of the fracturing in the surrounding rock of a roadway under a mining environment. Chen et al. [6] found that the asymmetric deformation of a roadway is caused by a change in the magnitude and direction of the stress field of the surrounding rock caused by mining stress. He and Zhang [7,8] analyzed the failure and instability mechanism of a roadway affected by mining in an adjacent large-scale fully mechanized caving face and put forward the use of high prestressed truss anchor cable support technology. According to the deformation characteristics of the large deformations in the soft surrounding rock, Yu and Liu [9] provided a set of critical technologies and their corresponding control principles. In addition, He et al. [10] proposed the design theory of a large nonlinear deformation of the surrounding rock, designed a coupled support method consisting of bolts and a metal mesh, and developed a new type of energy-absorbing anchor cable, characterized by a constant resistance and large deformation. Li et al. [11] analyzed the serious deformation occurring in the surrounding rock in a large section chamber, as well as the frequent failures of the bolt supports; subsequently, a new high-strength bolt grouting technology was proposed. Based on the deformation characteristics of loose and fractured rock masses and their influencing factors, Fangtian et al. [12] presented an entire support technology of section bolt grouting.
It is well known that the occurrence and development of plastic deformation are determined by deviatoric stress, which can control the failure of a rock mass and has an important significance regarding the influence of the plastic failure of a rock mass [13]. Using plastic mechanics and the Mohr-Coulomb theory, Ma et al. [14] obtained a formula for calculating the deviatoric stress of the surrounding rock of a circular roadway as well as a formula for the radius of a plastic zone. Based on the rock mechanics and a numerical simulation theory, Yu and Yuan [15,16] analyzed the distribution law of the deviatoric stress field and plastic zone during the process of deformation and failure of the surrounding rock of the roadway, aiming at the failure mechanism and stability control of the surrounding rock of the roadway. He and Xu [17,18] used the deviatoric stress theory to study the stress distribution of the roof support and floor under a coal pillar for a large cross-section cutting hole. Xie et al. [19,20] used a strain softening model to study the evolution law of deviatoric stress and the plastic zone of the surrounding rock of a gob-side retaining roadway. Li et al. [21] considered that adjusting the three-dimensional stress fields in the surrounding rock causes the majority of the principal deviatoric stress to concentrate on the filling body, causing the surrounding rock to fail.
In general, in the above studies, thorough analyses regarding the relationship between deformation and the failure characteristics of a roadway and the deviatoric stress were conducted. Based on the background of the gas tailgate in the 310101 working face of the Xinyuan coal mine, this paper mainly describes a study on the deflection of the PDSZ of the surrounding rock and failure rate of the plastic zone during the process of the working face. On this basis, the combined control technology of a roof truss anchor cable structure and a coal side anchor cable truss system is proposed, which effectively solves the control problem of a large deformation of the surrounding rock of a soft coal roadway under intense mining. Figure 1, the Xinyuan coal mine is situated northeast of Shouyang County, Jinzhong City, Shanxi Province, China, which is approximately 10.0 km from the center of Shouyang County. e 310101 working face, with an average depth of 500 m, is located in coal seam 3 of the first mining area in the Xinyuan coal mine, Shanxi Province, China. e average mining height is 4.0 m, and the average dip angle of the coal seam is 4°in the working face area. e coal seam is extremely soft (f � 0.2), and an endogenous fissure with one or two layers 0.02-0.1 m thick has developed. e immediate roof is mudstone, with an average thickness of 3.60 m. However, the thickness is unstable and reaches 10 m in local areas, whereas the seam floor is gray sandy mudstone, medium-to-thick layered, under a joint development with an average thickness of 4.50 m. Furthermore, a histogram of the regional coal and strata in the working face area is shown in Figure 2.

Geological Conditions of Mine Production. As shown in
An inclined comprehensive long-wall backward mechanized mining method is applied in the 310101 working face; that is, the width of the working face is 240 m, the length of the working face is 1,800 m, and the cycling progress is 0.8 m.
e mining roadway will continue to experience the mining influence of the working face for a long time to come. e Xinyuan coal mine is a high-gas mine, and to solve the problem of gas overruns on the working face and ensure production safety, a special gas drainage roadway is usually set up along the roof of the coal seam at a certain distance inside the tailgate, which is called the gas tailgate [22]. e gas tailgate of the 310101 working face is located 22 m from the tailgate and is retained for the next working face after mining in the 310101 working face, resulting in a lengthy period of deformation and destruction of the gas tailgate. e gas tailgate section has a rectangular shape with a width of 5 m and a height of 3 m. After excavating along the roof of coal seam 3, water leaching occurs in the local area of the roof of the gas tailgate, and the integrity of the surrounding rock is poor. e roof is easily damaged and can collapse through engineering disturbances and lateral pressure.

Severe Ground Pressure in the Soft Roadway under Intense
Mining. A severe ground pressure has occurred along the roadway located at coal seam 3 during the workface operations, as shown in Figure 3. In addition, numerous roof caving accidents have occurred in the 310201 gas tailgate and 310202 belt tailgate in the west wing of the first mining face of coal seam 3 during the production of the working face. e maximum roof caving height is more than 10 m, which blocks the entire section of the roadway, preventing ventilation and the ability to walk in the area. Collapses have occurred within a considerable range of the coal side; in addition, the expansion of the area without a collapse is obvious, and the overall displacement of the coal side has reached 1-2 m. e original support system of the roadway has been seriously damaged, such as a breakage of the roof bolts, a severe bending of the pallets, and W-band folding, whereas the roadway bolts are suspended owing to the collapse of the coal body, resulting in a large number of breakage failures of the roadway bolts. For a collapsed section of a secondary reuse belt roadway, the Xinyuan coal mine has required the excavation of a supplementary roadway with a length of 380 m to replace the collapsed section. After the collapse of the gas tailgate, the use of stacking, a supplementary anchor cable, and other reinforcement support measures have been adopted to strengthen the area and maintain its normal functionality.
Based on the characteristics of the strata pressure in the first mining face of the west side of the Xinyuan coal mine, we can see that the deformation and failure of the surrounding rock at the mining roadway are extremely critical during the production process of the working face. e support system has been damaged in several places, such as a bolt breakage and a warping of the W-band of the anchor cable.
e mining roadway is also being continuously renovated to maintain its normal functionality. However, in the tailgate located at the 310101 working face on the eastern wing, a malignant roof fall and a serious roof subsidence have occurred. e roof caving height of the roadway is 7-8 m, the roof caving length is more than 15 m, the roof subsidence of the roadway is more than 0.5 m, and the    Advances in Materials Science and Engineering convergence rate of the cross-section is 42%. Faced with a serious roof caving and roof subsidence in the eastern coal roadway where the mining influence is small, it is difficult to ensure the stability of the surrounding rock and avoid repeated renovations during the production process of the working face. Clearly, conventional comprehensive control technology measures cannot solve this problem. In combination with the deflection law of the PDSZ and the failure rate of the plastic zone of the gas tailgate during the mining process of the 310101 working face, a comprehensive control technology that employs a roof truss anchor cable structure and a coal side anchor cable truss system is proposed to solve the problem of controlling large deformations of the surrounding rock of the soft coal roadway and realize the safety and efficient production in coal mines under severe mining conditions.

Damage Range of Roadway Surrounding Rock.
After the excavation of the gas tailgate, the plastic surroundings of the shallow surrounding rocks are deformed and destroyed under the pressure of the overlying strata, the surrounding rocks are extruded into the roadway, and finally a natural balance arch is formed in a certain depth, as shown in Figure 4. e range and stress of surrounding rock failure area are important basis for roadway support. erefore, the elastoplastic theory is used to determine the range and stress of surrounding rock failure. According to the theory of natural balance arch, the rock mass above the natural balance arch is stable, and the area within the balance arch is the surrounding rock damage area. e damage range of the surrounding rock of the roadway is determined by equations (1)∼ (2) Depth of coal roadway coal seam damage C is as follows: In the formula, K is extrusion stress concentration factor around the roadway, according to the numerical simulation of the peak stress of the two sides; take K � 2.3; c is overburden bulk density, 25 kN/m 3 ; H is burial depth of the roadway, 500 m; and B is characterized mining. e dimensionless parameter of the influence degree is 1.4 under the influence of multiple mining; f y is coal seam hardness coefficient, 0.9; h is roadway height, 3 m; and φ is coal seam friction angle, 28°. It can be calculated that C � 1.83 m; that is, the damage depth of the side of the gas tailgate is 1.83 m. Destruction depth of roof rock layer b is as follows: In the formula, a is semicolumn distance of roadway, 2.25 m; α is inclination of coal seam, 3°; k y is stability coefficient of rock to be anchored; mudstone roof is generally taken as 0.5; and f n is hardness coefficient of anchored rock, 4.3. It can be calculated that b � 2 m; that is, the roof failure depth of the gas tailgate is 2 m.

Width of Roadway Coal Side Plastic Zone.
After the excavation of the roadway, the two sides of roadway were continuously damaged during the stress rebalance distribution of the surrounding rock until the boundary of the elastic stress zone, as shown in Figure 5. According to the theory of limit equilibrium zone, the width x 0 of the coal   Advances in Materials Science and Engineering tunnel plastic zone of the roadway can be obtained by the following formula: where x 0 is the width of the limit equilibrium zone; h is the height of the roadway, 3 m; k is the stress concentration factor at the peak of the stress, 2.3; c is the average bulk density of the overlying rock layer on the roadway, 25 kN/m 3 ; H is burial depth of the roadway 500 m; λ is the lateral pressure coefficient of the area; P is the resistance of the support body to the coal support; the two sides of the roadway are supported by bolts, taking 0.243 MPa; and internal friction angle at the coal seam interface is 27°: After calculation, x 0 � 4.78 m.

Significance of Deviatoric Stress and Establishment of
Numerical Simulation. At present, the ground pressure theory of the roadway mostly focuses on the influence of the surrounding rock stability, which is caused by gravity stress and the abutment pressure. However, theoretical studies and engineering practice [18] have shown that the failure and deformation of the surrounding rock are not the result of a certain role of the vertical or horizontal stress, but the result of multiple stresses acting together. According to the geotechnical plasticity mechanics [13], the state of stress at any point in the surrounding rock of the roadway can be decomposed into the sum of the spherical and deviatoric stresses. e state of stress at any point in the surrounding rock of the roadway can be expressed through multiple forms, and a special characteristic among all of the descriptions, namely, three principal stresses σ i (i � 1, 2, 3) arranged in vertical pairs, is found: where σ 1 − P indicates the principal deviatoric stress, which is recorded as σ′. is is an essential source of the deformation and failure of the surrounding rock. In this study, σ′ is used as an index to analyze the stability of the surrounding rock, and its value can be obtained through the following equation: To solve the problem of a gas overrun in the coal face, a gas tailgate is equipped in the 310101 working face for gas drainage and also functions as an air return in the next working face, which indicates that the gas tailgate will be affected by severe mining during the processing of the 310101 working face. In addition, the surrounding rock of the roadway is soft, which will create a strong deformation and failure in the surrounding rock of the roadway. To better study the essential causes of a large deformation and roof caving of a gas tailgate under severe mining, FLAC 3D numerical software was used to simulate and analyze the evolution law of the deviatoric stress of the surrounding rock of the gas tailgate in the 310101 working face. e simulation object is working face 310101 of the Xinyuan coal mine, and the model size is 350 m × 200 m × 90 m, as shown in Figure 6. Mohr-Coulomb model is adopted for each stratum in the model, and strain softening model [23,24] is adopted for soft coal and soft roof. e characteristics of strain softening of soft coal and soft roof are not the same in each mining area, so in order to carry out numerical calculation accurately, it is necessary to do specific experiments to obtain the characteristic parameters of strain softening of soft coal and soft roof and carry out numerical calculation verification. e characteristic parameters of strain softening of soft coal and soft roof are embedded in the fish statement and calculated in FLAC 3D . e lateral boundary of the model is fixed along the horizontal direction. e boundary of the floor of the model is fixed along the vertical direction. In order to verify the rationality of the strain softening model, a standard cylindrical numerical specimen with a height of 100 mm and a diameter of 50 mm was established in FLAC 3D . A constant velocity was applied on the top of the specimen, and the stress-strain curves of the standard test specimen of coal and roof mudstone in the simulation and laboratory test are shown in Figure 7. e results show that curves in laboratory test and simulation agree well, verifying the rationality of the strain softening model. e parameters of cohesion and friction angle of coal body and roof mudstone with plastic strain are determined through laboratory test (Table 1).

Analysis of the Deflection of PDSZ in Gas Tailgate.
e properties of the surrounding rock of the roadway deteriorate under the stress of a mining disturbance during the processing of the 310101 working face because both sides of the gas tailgate are soft and the bearing capacity of the retained coal pillars up to the roof is limited. As the working face continuously advances, a periodic fracture and caving are formed in the main roof strata above the stope. e fractured main roof touches the falling gangue in the gob and gradually begins to stabilize under the load-bearing effect of the gangue, whereas the stress of the surrounding rock of the roadway will reach a new static equilibrium under the combined action of the pillar support force and the stress of the mining disturbance [25][26][27]. e shallow surrounding rock of the gas tailgate undergoes dilatation and deformation under the excavation unloading. e deviatoric stress of the shallow surrounding rock is low and develops in the deep rock stratum. e deviatoric stress deflects until stabilizing, whereas the rock mass is weakened by the mining disturbance.
To better understand the deflection law of the PDSZ with the advance of the 310101 mining face, in this study, the deviatoric stress evolution law of surrounding rock of gas  tailgate during the mining process is analyzed from two aspects. ① When the working face advances to a different distance, a comparative analysis of the deviatoric stress of the surrounding rock is conducted at the same position as the gas tailgate. ② A comparison of the deviatoric stress of the surrounding rock is also conducted under different positions of the gas tailgate when the working face advances to a certain distance. e evolution characteristics of the deviatoric stress field with the advancement of the working face are comprehensively obtained. Figure 8, along the face advancing direction, the PDSZ in the surrounding rock of the gas tailgate deflects with the advancement of the working face. A deflection of the PDSZ in the surrounding rock of the gas tailgate occurs throughout the entire mining process. Before the working face advances 60 m, the distribution of the deviatoric stress in the surrounding rock of the roadway does not significantly change.

Nephogram of the Deviatoric Stress Distribution of the Same Cross-Section (y � 80 m) in the Gas Tailgate at Different Advancement Positions of the Working Face. From
e PDSZ is at the center of the roadway floor. e deviatoric stress field has a symmetrical annular distribution, and the value of the deviatoric stress is low within the area of 1.5-2 m near the surface of the roadway, whereas a high deviatoric stress distribution area is formed within a certain range of a deep roadway, which indicates that the surrounding rock of the roadway is slightly disturbed by the mining of the working face at this time, and the roadway remains consistently in a state of stability. When the working face advances 60-140 m, the distribution of high deviatoric stress in the surrounding rock of the roadway changes, and the high deviatoric stress of the roof necks at the shoulders of both sides, transforming from an annular stress area to a U-shaped high deviatoric stress area. e degree of deflection of the PDSZ of the roadway surrounding the rock increases with the distance of the coalface advancement, whereas the degree of deflection of the peak deviatoric zone of a coal pillar wall no longer changes during the 100-140 m mining process; in addition, the PDSZ gradually appears on the side of the solid coal, and the distribution range of the peak stress zone continues to deflect vertically downward with the advancement of the working face. When the mining face reaches 140 m, an asymmetric "sandwich" peak in the deviatoric stress zone is formed on both sides of the roadway and the variation of the peak stress zone tends to be stable. e peak in the deviatoric stress zone at the gob side of the roadway is located within the range of 3-5.5 m from the surface of the coal pillar with a large distribution, whereas the coal wall side is mainly located within the range of 3-4.5 m at the shoulder and bottom corners of the solid coal, and the shoulder angle distribution range is larger than that of the bottom corner. As the working face continues to advance, the distribution form of the peak in the deviatoric stress zone of the surrounding rock on both sides of the roadway no longer changes significantly. Only a strip of an increased deviatoric stress zone is formed on the upper part of the coal pillar, which obliquely runs the entire width. at is, the deviatoric stress field of the surrounding rock of the gas tailgate basically reaches a state of stability when the advancement distance of the working face is 140 m because the outer side of the coal pillar is under unidirectional or bidirectional compression, and the mechanical property of the coal pillar is poor. Under roof subsidence, a plastic failure easily occurs, shifting the high deviatoric stress of the coal pillar side to the solid coal side and allowing the deviatoric stress of the surrounding rock of the roadway to reach a new static level under the combined action of the support force of the coal pillar and the disturbance stress of the mining.

Nephogram of the Deviatoric Stress Distribution of the Surrounding Rock at Different Positions of the Gas Tailgate When the Working Face is at a Certain Position.
Considering the deviatoric stress distribution nephogram of the surrounding rock at different positions of the gas tailgate when the working face is at a certain position (y � 40, 80, and 160 m), the typical characteristics of the deviatoric stress field at different evolution stages are obtained, as shown in Figure 9. When the working face progresses at 40 m, as shown in Figure 9(a), the distribution of the deviatoric stress field in the surrounding rock of the roadway does not change, and only the deviatoric stress in the coal pillar expands horizontally toward the direction of the goaf with an increase in the lagging mining distance; however, the deviatoric stress distribution form in a coal pillar of the advanced mining remains almost unchanged. is indicates that the 22 m pillar has a certain bearing capacity for the roof during the initial stage of the working face mining, while effectively weakening the advancing influence of the working face mining on the gas tailgate. When progressing at 80 m, as shown in Figure 9(b), the PDSZ of the surrounding rock in the gas tailgate shows an obvious advancement distribution, whereas the deflection trend stops at 20 m ahead of the working face, and the deviatoric stress distribution remains unchanged as the advancement distance continues to increase, which indicates that the degree of disturbance of the surrounding rock in the gas tailgate is gradually weakened by the mining in advance of the working face and tends to maintain the stability of the initial excavation. Similar to the influence of the advanced mining of the working face, the PDSZ shows an obvious deflection phenomenon behind the working face. e degree of deflection and range of distribution of the PDSZ increase with an increase in the lag mining distance, the concentration of deviatoric stress gradually appears in the shoulder of the coal pillar in the gas tailgate, and the degree of stress concentration increases with the distance from the working face. As shown in Figure 9(c), the distribution form of the deviatoric stress field in the surrounding rock of the roadway changes dramatically under the influence of lag mining pressure after mining. e lateral side of the high stress zone at the shoulder corner of the roadway continues until it connects with the high stress zone at the goaf side. e range of distribution of the PDSZ in the surrounding rock of the gas tailgate increases significantly and transfers with an increase in the lag mining distance, although there is no significant change in the PDSZ of the goaf side behind the working face. Only the PDSZ of the solid coal side transfers with the increase in the lag mining. When the lag mining is at 60 m, an asymmetric "sandwich" peak in the deviatoric stress zone is formed on both sides of the roadway. is indicates that the bearing capacity of the coal pillar up to the roof is limited and that the deviatoric stress of the coal pillar reaches the ultimate bearing state after mining of the working face. With an increase in the lag mining distance, the distribution form of the PDSZ no longer changes. Only the high deviatoric stress zone at the shoulder corner of the coal pillar necks with an increase in the lag mining distance, which indicates that the deviatoric stress field of the surrounding rock reaches a stable state at a 60 m lag from the mining face. From the above analysis, we can see the following. (1) Considering the deviatoric stress distribution nephogram of the same cross-section (y � 80 m) in the gas tailgate at different advancement positions of the working face, the PDSZ of the surrounding rock in the gas tailgate rotates clockwise with the increase in the advancing distance of working face, and the deflection of the deviatoric stress peak zone on both sides of the roadway tends to be stable when the advancing distance of the working face is 140 m. Among them, the PDSZ at the gob side of the roadway is located within the range of 3-5.5 m from the surface of the coal pillar with a large distribution, whereas the coal wall side is mainly located within the range of 3-4.5 m at the shoulder and bottom corners of the solid coal, and the distribution range of the shoulder corner is larger than that of the bottom corner.   Advances in Materials Science and Engineering the mining face, and the distribution form of the PDSZ on both sides of the roadway no longer changes to a significant degree.

Analysis of the Evolution of Plastic Zone in Gas Tailgate.
After the influence of the mining of the 310101 working face on the gas tailgate, the deviatoric stress field of the surrounding rock of the roadway will tend to deflect toward the goaf along with the mining in the working face. Under a high deviatoric stress, the surrounding rock of the roadway will produce a certain range of the plastic zone, and the deflection of the deviatoric stress field will directly affect the expansion and development of the plastic zone of the surrounding rock. A plastic failure of the surrounding rock forms in the middle section (y � 80 m) of the gas tailgate along the advancing direction of the working face at different mining distances, as shown in Figure 10(a). It can be seen that the main failures of the surrounding rock at the bottom corner of the coal pillar and the shallow shoulder corner of the coal wall are tensile and shear failures, whereas the other parts of the rock mass are mainly subjected to a single shear failure. e plastic failure zone of the surrounding rock of the roadway is small and uniform with an elliptical distribution at the initial stage of mining. With the advancement of the working face, the damage range of the plastic zone is evidently not coordinated with the development. When the advancing distance of the working face is 140 m, the range of change of the plastic zone reaches the maximum value and tends to reach stability. e distribution form of the plastic zone changes from elliptic to irregular, whereas the depths of the plastic zone of the roof and floor remain unchanged throughout the mining process, and the rock mass in the rest of the surrounding rock of the roadway shows an obvious nonuniform failure. Statistical curves of the plastic failure rate of the surrounding rock of the roadway varying with the mining distance of the working face are shown in Figure 10(b). e ratio of the change in the range of the plastic zone and the initial range is defined as the failure rate coefficient, which is recorded as η.
According to the failure coefficient curve of the surrounding rock of the roadway, the failure of the plastic zone of the surrounding rock of the gas tailgate can be roughly divided into three categories under intense mining: the failure rate of the shoulder corner of the roadway and the bottom corner of coal pillar is the fastest, the failure rates of the two sides and the bottom corner of the coal wall are the second fastest, and the failure rates of the roof and floor are the slowest. For a type-I failure rate curve, the failure rates of the left-bottom and right shoulder corners are much higher   floor are as high as 4 m, which means the failure of the plastic zone of the roof and floor is mainly related to the property of the surrounding rock of the roadway. According to the above analysis and drilling peep [28], the failure rate of the plastic zone and the deflection law of the PDSZ maintain a synchronous and coordinated relationship with the advancement of the working face. e failure range of the plastic zone is stable with the stability of the PDSZ, which indicates that the PDSZ dominates the growth rate and development of the plastic zone. e relationship between the distribution of the deviatoric stress and the range of the plastic zone is more intuitive, as shown in Figure 11. e maximum depth of the plastic failure of the surrounding rock of the gas tailgate is 5 m, which is less than the outline of the PDSZ (5.5 m), but larger than the inner outline of the PDSZ (3 m). e plastic failure line remains between the inner and outer outlines of the PDSZ. A plastic failure occurs in the rock mass within the inner edge of the PDSZ and extends outward to the plastic failure line. erefore, the rock mass in the range of layered deviatoric stress isosurface within and outside the PDSZ is in the state of elastic-plastic deformation, and the rock mass is in the transitional state of stability and instability. To achieve the stability of the surrounding rock of the gas tailgate, it is necessary to control the stability of the unstable rock mass.

Control Mechanism and Technology of Surrounding Soft Coal Roadway under
Intense Mining e above analysis shows that the gas tailgate in the 310101 working face belongs to a soft coal roadway, with a developed crevice and low strength of the surrounding rock, which are vulnerable to deformation and destroyed by disturbances during an engineering project. It is inevitable that a large range of fragmentation zones and plastic zones of the surrounding rock will be formed within a short time after excavation of the roadway. In addition, the PDSZ of the surrounding rock of the roadway deflects to the side of the goaf with an increase in the advancing distance of the working face, and the maximum depth of the plastic failure of the surrounding rock of the roadway is approximately 5 m under a high deviatoric stress. However, the strength and length of the anchor bolt (cable) in the original support are too low to ensure that the anchorage foundation of each part of the anchor bolt (cable) is within the elastic zone. e broken surrounding rock is strongly extruded toward the free surface, resulting in a large convergence deformation of the surrounding rock, and even a roof caving and collapse.
e support system is seriously damaged, which results in an instability of the entire section of the roadway and its continued use, as is shown in Figure 12.
erefore, a comprehensive control technology that employs a truss structure of the roof with a strong bolt system (Figure 13(a)), a multianchor cable-steel beam system (Figure 13(b)), a high prestressed anchor cable truss system, (Figure 13(c)), and a coal side anchor cable-channel steel truss system (Figure 14) is proposed.

Roof High Prestressed Strong Supporting Technology.
A surrounding rock fractured zone is formed in the shallow part of the gas tailgate of the 310101 working face when affected by the mining and roadway excavation. A strong bolt control system has been successfully applied under many complex conditions, such as multiple mining effects, soft and fractured surrounding rock, and a large span of roadway [9,[29][30][31]. Super strong thread steel bolts with a superior mechanical property, high prestressing, and a timely support can significantly improve the residual strength of the broken surrounding rock and form a large effective compressive stress zone in the roof, indirectly restraining the expansion of the plastic and broken zones into the deep roof. Consequently, this significantly improves the integrity and overall load-bearing capacity of the shallow surrounding rock of the roadway and promotes the formation of a prestressed load-bearing structure composed of a support and surrounding rock, as shown in Figure 13(a).
us, based on engineering practice and a numerical simulation, super strong thread steel bolts of Φ � 20 mm × 2,500 mm are used, with seven bolts arranged in each row. Considering that the plastic zone of the shoulder angle of the roadway has the fastest failure rate, the distance between two bolts near the two sides of the roadway is 700 mm, and the distance between the other bolts is 800 mm. e bolts for each of the sidewalls of the roadway are set at 200 mm away from the sidewalls, the angle between the bolt for each of the sidewalls of the roadway and the vertical direction is 20°, and the other bolts are arranged vertically. e line space of the strong thread steel bolts is determined to be 800 mm, and the diamond metal mesh, specified as 1,100 mm × 2,800 mm in size, is used along with a Φ 14 mm steel ladder beam and a steel bearing plate.
A multianchor cable-steel beam system is the key to ensuring the stability of the roof. It consists of W-steel tape and several single anchor cables connected with the W-steel tape and anchored to the depth of the roof, forming a prestressed bearing structure of multianchor cables in a steel beam support. e single anchor cable crosses the plastic failure line and connects the prestressed bearing structure formed by the shallow bolt support with a deep stability of the rock stratum of the roof. An inclined arrangement of the anchor cables near the side of the shoulder is adopted to weaken the expansion    Figure 14: Principle of cable-channel steel truss system with coal side anchor.
Advances in Materials Science and Engineering 13 rate of the plastic zone at the shoulder corner of the roadway. e anchor cables are joined by W-steel tape with a high tensile strength to form an integral bearing structure and jointly resist the deformation of the surrounding rock and improve the stability of the prestressed bearing structure. In the design of the anchor cable parameters, the anchor cable should cross the failure line of the plastic zone, and the anchor cable foundation should be located as far as possible above the deeply stable rock stratum of the roof, as shown in Figure 13(b). us, based on engineering practice, a numerical simulation, and a theoretical analysis, steel strand cables composed of 19 steel wires, specified as Φ � 17.8 mm × L9500 mm in size, are used to strengthen the support, with five cables arranged in each row. e row and line spacing of the steel strand cables is determined to be 1,100 mm × 2,400 mm, and the angle between the cables, set at 300 mm away from the sidewalls, and the vertical direction is 20°. e W-steel tape, specified as 5,000 mm × 220 mm × 4 mm in size, is used for linking the cables and operates in coordination with the steel bearing plate.
Owing to the large span of the roadway and the weak mudstone in the roof, a roof caving is prone to occur under intense mining. erefore, it is necessary to take effective measures to prevent a roof caving based on the above support to ensure the safety of the roadway roof. e cable truss system is a new support structure developed to solve the problem of a large deformation and easy roof caving of the roadway under complex geological conditions [32]. e cable truss system consists of a long anchor cable and a special locking device. e anchor foundation is placed in deeply stable compressive rock strata in the two shoulders of the roadway. e two inclined anchor cables are connected by a special connector and form an outward inclined groove in the active support structure after prestressing, as shown in Figure 13(c). e prestressed cable truss system exerts a high pretension from the horizontal and vertical directions, realizing a three-dimensional compression of the surrounding rock. During the process of roof subsidence of the roadway, the cable truss system is gradually blocked, the pressure of the shallow surrounding rock is strengthened, and the support and surrounding rock are jointly loaded, preventing a large deformation of the surrounding rock of the roadway and providing a new means for the support of a large deformation roadway. us, based on engineering practice, a numerical simulation, and a theoretical analysis, a highstrength and highly elongated prestressed steel strand composed of 19 high-strength steel wires of Φ 17.8 × 9,500 mm in size is adopted for the cable truss system, the pretightening force of which can reach no lower than 160 kN. e angle between the cables, which is set at 1,300 mm from the sidewalls, and the vertical direction is 20°. e cable truss system is connected by a lock matched with 17.8 mm steel wires and a special cable truss connector.

Control Technology of Cable-Channel Steel Truss of Coal
Side Anchor. Because the outer side of the coal pillar is under unidirectional compression and the coal body is poor, a plastic failure easily occurs under roof subsidence.
erefore, a strong bolt support system should still be used on both sides of the gas tailgate. Considering the weak and broken deformation of the coal body at the side and to further control the expansion deformation of the surrounding rock of the crevices, a 3,000 mm length bolt is selected to form a large bolt support structure. Consequently, this significantly improves the stress of the surrounding rock within the peak deviator stress zone, delaying the transfer of a high deviator stress to the side of the solid coal as far as possible and weakening the shear failure from a high deviator stress of the coal mass, as shown in Figure 14.
us, based on engineering practice, a numerical simulation, and a theoretical analysis, super strong thread steel bolts of Φ20 mm × 3,000 mm in size are used, with a row and line spacing of 800 mm × 800 mm. e angle between the bolt, which is set at 300 mm away from the roof, and the vertical direction is 20°. e diamond metal mesh, specified as 2,600 × 1,100 mm in size, is used along with steel and wooden bearing plates.
According to the numerical simulation, it can be seen that the PDSZ gradually deflects toward the coal pillar side and the solid coal side with an advancement of the working face, and the rock mass in the PDSZ is in a transition between stability and instability. To realize the stability of the surrounding rock of the roadway, it is necessary to control the stability of the unstable rock mass in the PDSZ. erefore, a truss anchor cable is used to strengthen the support of the roadway side. e shear deformation of the surrounding rock at the corner of the roadway can be effectively controlled by an inclined anchor cable crossing the PDSZ. e cable truss system is composed of anchor cables connected by channel steel, which can form a continuous compressive stress zone on the shallow surrounding rock of the roadway side. is changes the support mode and structure and enhances the self-supporting ability of the coal mass on the roadway side.
us, based on engineering practice, a numerical simulation, and a theoretical analysis, a high-strength and highly elongated prestressed steel strand composed of 19 high-strength steel wires of Φ17.8 × 5,300 mm in size and a 1.8 m long number 14 steel channel is adopted for the cable-steel channel truss system. e angle between the cables, which is set at 800 mm away from the roof, and the vertical direction is 20°, and the angle between the cables, which is set at 1,000 mm away from the floor, and the vertical direction is 5°. e line spacing of the steel strand cables is determined to be 2,400 mm.

Engineering Practice
6.1. Support Parameters. According to the above theoretical analysis, numerical simulation, and engineering practice, the parameters of the gas tailgate in the 310101 working face are determined, as shown in Figure 15. e actual roof support design was as follows: super strong thread steel bolts of Φ 20 mm × 2,500 mm in are used, with seven bolts arranged in each row. e line spacing of the strong thread steel bolts is determined to be 800 mm, and a diamond metal mesh specified as 1,100 mm × 2,800 mm in size is used along with a Φ 14 mm steel ladder beam and a steel bearing plate. Steel strand cables composed of 19 steel wires specified as Φ 17.8 mm × L9500 mm in size are then used to strengthen the support, with five cables arranged in each row. e row and line spacing of the steel strand cables is determined to be 1,100 mm × 2,400 mm. e W-steel tape specified as 5,000 mm × 220 mm × 4 mm in size is used for linking the cables and operates in coordination with the steel bearing plate. In addition, a high-strength and highelongation prestressed steel strand composed of 19 highstrength steel wires of Φ17.8 × 9,500 mm in size is adopted for the cable truss system, the pretightening force of which can be no lower than 160 kN. e cable truss system is connected by a lock matched with 17.8 mm steel wires and a special cable truss connector.
For the coal side support, super strong thread steel bolts of Φ 20 mm × 3,000 mm in size are used, with four bolts arranged in each row. e row and line spacing of the strong thread steel bolts is determined to be 800 mm × 800 mm. In addition, an anchor cable-channel steel truss support system is adopted with a high-strength elongation prestressed anchor cable specified as Φ 17.8 mm × 5,300 mm in size using 1.8 m long number 14 channel steel, and the row space of the anchor cables is determined to be 2,400 mm.  the surface displacement of the gas tailgate is monitored using cross point methods; the monitoring data before and after mining are shown in Figure 16. Before mining, the convergence of the surrounding rock of the gas tailgate is extremely small, the maximum displacement of the roof to floor of the gas tailgate is no more than 100 mm, and the maximum displacement of the two sides of gas tailgate is no more than 140 mm. After mining, the maximum displacement of the roof to floor of the gas tailgate is no more than 310 mm, the maximum displacement of the two sides of the gas tailgate is no more than 160 mm, the roof separation of the gas tailgate is 15 mm, and the roof is in a stable state.

Support
After adopting the above-mentioned combined control technology, the problem of a large-area roof caving of the mining face has been effectively solved. e effective control of the gas tailgate not only provides the basic conditions for ventilation and gas control, but can also help excavate a smaller section of roadway, which resolves the situation of the excavation seriously replacing the out-of-balance state, reducing the loss of exploitable resources of the coal mine and significantly increasing the economic and technical benefits of the enterprise. e output of working face is increased from 1.2 to 1.8 Mt/a, which effectively solves the difficult problem of coal resource mining under severe conditions and realizes the safe and efficient production of the coal mine.

Conclusion
In this paper, it is concluded that the peak stress of the partial stress of the weak surrounding rock of the gas tailgate under the influence of strong mining will be significantly deflected, and the plastic zone will expand nonuniformly.
e key control area of the anchor cable and the anchorage range of the anchor cable were verified by theoretical calculations, drilling peeping, and field practice.
(1) e strain softening model is used to numerically calculate that the strong mining influence on the working face will cause the peak stress zone of the surrounding rock of the gas tailgate to deflect. e PDSZ at the gob side of the roadway is located in the range of 3-5.5 m from the surface of the coal pillar, while the coal wall side is mainly located in the range of 3-4.5 m at the shoulder corner and bottom corner of the solid coal. e peak area of the partial stress is the key control area. (2) Strong mining in the working face causes the plastic area of the surrounding rock of the gas tailgate to expand nonuniformly. e solid coal shoulder angle, coal pillar side shoulder angle, and coal pillar side bottom angle have the largest deformation and damage and the damage ranges are 4 m, 4.5 m, and 5 m, respectively. ese three areas are the focus of support control. (3) e plastic failure line of the surrounding rock of the gas tailgate is always between the inner and outer contours of the peak stress zone, and the rock mass in the peak stress zone is in a stable and unstable transition state. e support range of the anchor cable should cross the plastic failure line of the surrounding rock of the gas tailgate. (4) A truss anchor cable support system with integrated locking and large-scale support function is proposed to jointly control the roof and the two sides of the surrounding rock of the weak roadway in strong mining. e maximum deformations of the roadway and the two sides of the roadway are 310 mm and 160 mm, respectively, and the control effect is good.

Data Availability
All data supporting the conclusions draw by this study can be obtained from the corresponding author upon request.

Conflicts of Interest
e authors declare that there are no conflicts of interest.

Roof-to-floor convergence
Rib-to-rib convergence

16
Advances in Materials Science and Engineering