Performance Analysis of Hydrodynamic Pressure Finger Seal by Wall Slip Effect

Hydrodynamic pressure finger seal1 is a kind of flexible noncontact dynamic sealing device with good application potential. It relies on the ultrathin dynamic pressure film effect produced by the rotation of finger boot and rotor to realize the design of noncontact and low leakage and is suitable for high-speed dynamic sealing parts. However, under the high-speed condition, there is a wall slip effect when the gas flows in the microchannel with a thickness of about 10 μm between the finger boot and rotor, which affects the stability of the dynamic pressure air film and also affects the change of the air film bearing capacity and the leakage rate of the finger seal.+erefore, based on the theory of microflow, the interstitial flow field model of finger seal under fluid dynamic pressure is established, and its slip effect under high speed is analyzed. +e results show that the slip ratio of the sealing medium temperature of 500°C and 0.1MPa conditions reached 27.28%. When considering the slip effect of the wall surface generated by the gas under shear driving, the gas film bearing capacity decreased and the leakage rate increased. When the pressure difference between the upper and lower reaches of the seal is 0.1MPa, and the rotor line speed is 400m/s, the gas film bearing capacity decreases by 17.39% after considering the slip effect of the wall surface, and the leakage rate increases by 14.06%. +e results provide an important reference for the structural design and leakage control of hydrodynamic finger seal.


Introduction
e hydrodynamic pressure finger seal is a new type of finger seal derived from the contact finger seal; meanwhile, the characteristic of low leakage of contact finger seal and long life of noncontact seal are also made [1,2]. Due to its characteristics of good sealing performance and low manufacturing cost, it has a wide application prospect in improving the performance of aero-engine [3].
In view of the excellent application prospect of hydrodynamic finger seal, many researchers have carried out a lot of research on fluid dynamic pressure finger, the effect of the stiffness of finger beam, the stiffness of air film, and the bearing capacity seal. By using finite element simulation and equivalent dynamic model, Marie [4] studied air film on the sealing performance of hydrodynamic finger seal and also analyzed the displacement transfer rate of hydrodynamic air film, providing an important idea for the theoretical design and study of hydrodynamic finger seal.
According to the temperature characteristic, such as hydrodynamic pressure under the effect of dynamic characteristics. Braun et al. [5] analyzed the thermal characteristics of hydrodynamic pressure of finger seal, finite element analysis method to analyze the different rotating speed and sealing medium environment temperature, hydrodynamic pressure finger seal leakage flow characteristics, and the method of equivalent dynamic hydrodynamic finger seal dynamic characteristics. For the hydrodynamic pressure of finger seal structure design, selection of materials and the temperature rising characteristic research provides an important reference. Temis et al. [6] also studied the adaptability of hydrodynamic finger seal to the dynamic adjustment of rotor by using fluidsolid coupling simulation method and equivalent method and studied the feasibility of the formation of dynamic pressure air film. Fleming [7] conducted a study on the effect of rotating speed and film thickness on the sealing performance of hydrodynamic finger seal and confirmed that the fluid film always exists in various operating conditions. Proctor et al. [8] studied the leakage, power consumption, and wear characteristics of hydrodynamic finger seal under static conditions and fixed linear velocity under the condition of 56.7 m/s by using the upstream and downstream pressure difference and conducted comparative analysis with brush seal and contact finger seal. Meanwhile, the structural design, theoretical analysis of dynamic characteristics, and performance simulation research in combination with the working characteristics of the hydrodynamic finger seal were also carried out [9][10][11][12][13][14][15].
At present, the research on hydrodynamic finger seal mainly focuses on the design of the finger beam line [16], the optimization of the axial structure of the finger seal [17], the construction of the equivalent dynamic model of the finger seal, and performance simulation analysis [18]. However, the study of hydrodynamic pressure finger seal leakage flow characteristics still needs to be further explored. Due to the slip phenomenon of the wall surface during the flow of gas in the microchannel with a thickness of about 10 μm between the finger boots and the rotor, the slip effect of gas flow in the microchannel was not considered in previous studies, and this microscale flow slippage phenomenon has an important influence on the parameters such as gas film bearing capacity and leakage rate of hydrodynamic pressure finger seal [19]. erefore, the analysis of leakage gap flow field characteristics of hydrodynamic finger seal, considering the wall slip effect on leakage flow, can enrich the design and engineering application of high-performance hydrodynamic finger seal and is of great significance for the improvement of aeroengine sealing technology. erefore, based on the microscale flow theory, a flow field model of hydrodynamic pressure finger seal leakage gap is established, and the flow slip characteristics of the microscale leakage channel seal medium are studied. In this paper, by simulating the flow state of the gas under the condition of wall slip, the difference between the gas film bearing capacity and the leakage volume under the condition of considering wall slip at a specific speed and the boundary condition without wall slip is analyzed, and the flow of the sealing medium in the leakage gap flow field driven by shear is simulated numerically. It provides theoretical guidance for calculating leakage performance of hydrodynamic finger seal under dynamic conditions and verifying the rationality of test results.

Hydrodynamic Pressure Finger Seal Structure
Characteristics and Working Principles e hydrodynamic finger seal consists of high-pressure finger plates, low-pressure finger plates with sealing boots, front and rear baffles, rivets, and other components, and its structure is shown in Figure 1. Different from the contact finger seal, the seal boot at the free end of the low-pressure finger plate adds an extended lengthening structure in the axial direction. When the rotor rotates at high speed, an action pressure film is formed between the low-pressure sealing boots and the rotor, and the low-pressure sealing boots are lifted to achieve noncontact between the seal and the rotor. At the same time, the action pressure film hinders the leakage of the seal medium in the leakage gap. e fluid dynamic pressure film formed by the rotor rotation can ensure the seal's low leakage and long-life characteristics, and the flexible finger beam sealed by the fluid dynamic pressure finger can adapt to the radial dynamic beating caused by the rotor due to vibration or thermal deformation. erefore, this hydrodynamic pressure finger seal is suitable for dynamic sealing conditions with demanding seal leakage level and high work life requirements, which makes it have good working performance and application prospects.

Leakage Flow Analysis of Hydrodynamic Pressure Finger
Seal. e sealing function of hydrodynamic pressure finger seal is mainly based on the action of the dynamic pressure gas film formed between the low-pressure seal boot and the rotor. Under high-speed conditions, the thickness of the gas film is only about 10 μm, and macroscopic fluid mechanics models and formulas may no longer be suitable for microscale flow. Since the characteristic scale of flow field is reduced to micron level, the flow characteristics of fluid show significant size effect compared with macroscopically. At this point, many physical quantities in the macroscopic state will change, and the flow speed on the surface of the channel will show a slip phenomenon, and the surface viscous shear stress will be reduced accordingly. At this point, the effect of the wall slip on the flow of gas sealed by the hydrodynamic pressure finger cannot be ignored. For this reason, the study refers to the study of wall velocity slip under the micronanometer gap flow field at home and abroad. Considering the influence of wall velocity slip, the leakage flow analysis of hydrodynamic pressure finger seal is presented [20,21].
In the microscale gas flow, K n (Knudsen) number is usually used to describe the degree of microscaling of the flow. K n number is a dimensionless number. Like the Re number and the M number, it has a very important position in the study of gas flow [22], and K n is calculated in the following equation: where λ is the mean molecular free path of the gas and L is the characteristic scale of the flow field. According to the size of K n number, the gas flow field can be divided as follows: (1) When K n ≤ 10 −3 , this field of flow belongs to the continuous medium area. Fluid motion can be simulated using the N-S equation plus nonslip boundary conditions. (2) When 10 -3 < K n ≤ 10 -1 , this field of flow belongs to the slip area. e fluid begins to deviate from the thermodynamic equilibrium, at which point the fluid can still be described by the N-S equation, but the boundary slip conditions need to be revised. (3) When 10 −1 < K n ≤ 10, this field of flow belongs to the transition area. At present, the flow problem in this research area is usually solved by Boltzmann equation, Monte Carlo method, and other methods. (4) When K n > 10, this field of flow belongs to the molecular free flow area. In the free molecular zone, air flow is usually described and analyzed using the point of view of particle motion.
Combined with the actual working conditions of the hydrodynamic pressure finger seal, the minimum characteristic scale of the flow field is 0.00635 mm, and the average free path calculation of the gas molecule is shown in the following formula: where d represents the diameter of the gas molecule and n represents the density of the number of molecules. According to Boltzmann's theory, the ideal gas state equation for the sealed medium in the leakage gap can be constructed as shown in the following: where P represents the working pressure of the gas. In this article, the actual working pressure is 0.1 × 10 6 Pa, k represents the Boltzmann constant, and k � 1.3806505 × 10 −23 J/K. Formula (3) is brought into formula (2), and the average free path calculation formula (4) of the gas molecule is reduced: According to the actual operating state of fluid dynamic pressure, the temperature T � 773 K and the air molecular diameter d � 3.46 × 10 −10 m are taken. According to formula (4), the average free path of the gas molecule is calculated to be λ � 2.0065 × 10 −7 m.
According to the K n value calculation formula (1), K n � 0.03159 is obtained. Obviously, 10 −3 < K n ≤ 10 −1 , so it can be seen that the range of K n number is in the slip region. At this point, although the collision frequency between gas molecules is still much higher than the collision frequency between gas molecules and solid wall surfaces, the microscale effect cannot be ignored. In the slip zone, the thin effect gradually begins to appear, and the fluid begins to deviate from the thermodynamic equilibrium. At this time, the fluid can still be described by the N-S equation, but the boundary slip conditions need to be revised.
By analyzing the characteristics of the watersheds in the hydrodynamic pressure finger seal leak channel, it is shown that the boundary condition of the nonslip wall surface may no longer be applicable to the calculation when the gas flows in the hydrodynamic pressure finger seal tiny leakage channel. At the same time, the slip effect of the wall surface at the microscale downstream solid coupling interface is verified. e slip boundary condition of the wall surface becomes an unnegligible factor affecting the leakage flow characteristics, which affects the overall working stability and reliability of the hydrodynamic pressure finger seal system. is effect is particularly important for the clearance flow under extreme conditions such as high shear and heavy loads.

Slip Effect of Hydrodynamic Finger Seal.
For the slip law of the wall, Navier first proposed the simple slip model formula (5) and considered the velocity of the fluid medium near the wall as a simple function of the velocity gradient, as shown in the following: In the abovementioned formula, w represents the wall boundary, β represents the slip length parameter, and u slip represents the wall slip speed. Since then, the slip boundary condition model of the wall surface has been called the Navier slip model. e Navier slip model has been validated by experiments and molecular dynamics simulations and has been used in research to consider the slip phenomenon of the wall surface. However, when applying the Navier slip model, there is no strict distinction between liquid and gas.
For the gas slip law, Maxwell proposed the slip equation (6) for thin gas kinematics: where δ is the interface momentum adjustment coefficient, which represents the ratio of the number of molecules reflected by the gas molecule at the solid wall surface, and λ represents the average free path of the gas molecule. e Maxwell slip model formula is the slip condition of the wall surface of the gas. e slip model of the gas is often used in ultra-high-speed microscale analysis. Because the rotor moves at speed v relative to the sealing boot, the sealed boot is fixed, and the motion of the rotor drives the flow of gas. erefore, the established shear flow model is shown in Figure 2.
From the N-S equation, it can be obtained that the control equation is In the above equation, u is the velocity component of the rotor that drives the gas, μ is the hydrodynamic viscosity, and the pressure gradient dp/dx is the constant value.
Integration of equation (7) can be obtained as follows: Considering the slip boundary conditions on the wall, the boundary conditions in formulae (8) and (9) are shown in the following formula: where L s represents the slip length of the fluid in the gap and can be obtained from the following: where δ is the interface momentum adjustment coefficient, which represents the proportion of molecules reflected by gas molecules at the solid wall surface. In general, the value range is 0.1 to 0.2 and here is 0.1 computation [23,24]. λ represents the average free path of gas molecules. Bringing the boundary conditional formula (10) into equations (8) and (9), the integral constants c 1 , c 2 calculations can be obtained as shown in the following: e slip velocity formula (14) can be obtained by bringing the obtained integral constants c 1 , c 2 into equation (9): When the flow is only caused by the rotation of the rotor, the pressure gradient dp/dx is zero in the channel which simplifies as follows: e slip speed of the rotor and the rotor speed in the channel are shown in the following: where h is the clearance height and L s is the slip length parameter.
According to the slip model equation of the Navier wall surface and the slip equation of the thin gas kinematics proposed by Maxwell, the slip parameter L s can be obtained. Based on the above calculation, the average free path of the gas molecule is λ � 2.0065 × 10 −7 m. e slip parameter L s � 3.81235 × 10 −6 m. e ratio of rotor slip speed and rotor speed in the channel is 0.7272. e slip rate can be obtained according to the slip rate formula: where V w is the wall rotor speed, and V f is the speed at which the wall surface drives the gas molecules in the gap flow field. e slip rate can be calculated as s � 27.28%. e calculated slip rate can be used as the boundary condition for hydrodynamic pressure finger seal leakage calculation.

Calculation Model of Hydrodynamic Finger Seal.
Hydrodynamic pressure finger seal leakage performance analysis is realized by analyzing the fluid region between finger seal and seal rotor. Considering that hydrodynamic pressure finger seal has cyclic symmetry characteristics on the structure, in the analysis model, only one cyclic unit was selected, and the leakage gap between the high-pressure and low-pressure finger boots and the rotor was used as the fluid analysis area to reduce the calculation amount. e region of the fluid is shown in Figure 3. e hydrodynamic pressure finger seal is made up of two interlaced pieces of low-pressure finger and high-pressure finger. As shown in Figure 4, for the intuitive display, a distance is drawn between the two. Among them, the gap between the two high-pressure finger beams in the highpressure seal sheet and the three areas of the two cuneiform gas membranes between the high-pressure finger boots and the external surface of the rotor constitute the first half of the flow domain. e two gaps formed between a finger beam in a low-pressure finger seal and a finger beam in the front and rear, and the cuneiform gas membrane between the lowpressure finger boot and the outer surface of the rotor constitutes the latter half of the flow domain. erefore, the stream domain can be divided into six parts. e hydrodynamic pressure finger seal flow area calculation model is shown in Figure 4, and the corresponding finger seal structure parameters are shown in Table 1.
e simulation analysis is completed through the Ansys Workbench 15.0 CFX (Computational Fluid Dynamics X) fluid analysis module. e inlet of the air flow between the high-pressure boots and the rotor in figure b is set as the open boundary condition of Opening 1. According to the pressure of sealing medium, it is set as the pressure boundary condition. In the figure, the two-way straight arrow indicates that airflow can be in or out. e central region is the upper surface of the airflow layer between high-and low-pressure boots and rotor, and it is the interface surface of fluid-solid coupling, which is set as interface boundary condition. e inner area is the outlet of airflow, and the open boundary condition is set as Opening 2.
e pressure boundary condition is given according to the pressure of the leaking low-pressure chamber. e area on both sides is set as the boundary condition of symmetry, which is the circumferential circular symmetrical wall surface of leakage clearance. e lower surface of the air layer between the high and lowpressure boots and the rotor is in contact with the rotor, which is set as the condition of moving wall, and the moving speed takes into account the effect of slip rate.

Analysis of Grid Independence.
In order to eliminate the influence of mesh quality on the calculation results and reduce the calculation time and complexity, this paper analyzes the mesh quality independence of hydrodynamic pressure finger seal fluid structure coupling. e number of meshes can be controlled by adjusting the related parameters such as element sizing and relation. Taking the number of grids in solid domain and fluid domain as variables and the leakage amount of hydrodynamic finger seal as analysis target, the influence of different grid numbers on the leakage amount is analyzed comparatively.
As shown in Figure 5, when the number of grids in solid domain and fluid domain is lower than a certain value, the leakage corresponding to different number of grids varies greatly. When the total number of grids is 51600, the leakage is 2.62 × 10 −5 kg/s. When the number of meshes exceeds this value, with the increase of the number of meshes, the change of leakage value is very small. erefore, as long as the number of selected grids exceeds the above values, the calculation results are independent of the grid. Figure 6 shows the grid under the current settings.

Verification of the Simulation Method.
In [25], the noncontact finger seal with herringbone groove structure on the rotor surface has been tested in a very tight dynamic and static state, and the detailed and credible test data are given. In order to verify the accuracy of the numerical model in this paper, the same numerical model as that in [25] is established, and the two-way fluid structure coupling calculation is carried out under the same boundary conditions as the experimental values. Finally, the calculation results are compared with the test data. e leakage characteristic test parameters in [25] are given in the form of flow factors, which are defined as follows: where _ m is the mass flow through the whole flow field and the unit of it is kg/s; T avg is the average temperature of the finger seal inlet and the unit of it is k; P u is the finger seal inlet pressure and the unit of it is MPa; D seal is the outer diameter of the rotor corresponding to the finger seal and the unit of it is m. erefore, the unit of flow factor is kg·K 1/2 /(MPa·m·s). In this paper, a group of dynamic test data is selected to compare with the numerical simulation results, as shown in Figure 7. When the temperature is 300 K and the rotating speed is 5000 r/min and the pressure difference is 13.8 kPa, 34 kPa, 69 kPa, 103 kPa, 138 kPa, 176 kPa, 207 kPa, and 241 kPa, respectively, the flow factors calculated by simulation are consistent with the overall trend of the test results in [25].
It can be seen from Figure 7 that when the pressure difference is 103 kPa, the change rate of flow factor is large, and the curve begins to become gentle and gradually keeps consistent with the change rate of simulation results. is is due to the uncontrollable factors such as assembly state and leakage channel in the test, which lead to the difference between the initial low-pressure difference and the highpressure difference. When the pressure difference exceeds 69 kPa, the simulation result is smaller than the test result. e reason analysis is as follows. First, the leakage in the  actual test includes three channels, and the simulation model mainly considers two channels: finger boot gap and finger gap leakage. Second, the leakage caused by temperature effect, rotor vibration, and other uncontrollable factors will increase in the test process. e simulation value is about 80% of the test value, which is also consistent with the previous saying that the leakage path of finger seal is mainly the leakage between finger boots and finger pieces, thus verifying the accuracy and reliability of the numerical method and simulation model.

Results and Discussion
When the pressure difference in the upper and lower reaches of the seal is 0.1 MPa, the ambient temperature is 500°C, and the rotor surface line speeds v are 100 m/s, 200 m/s, 300 m/s, and 400 m/s, respectively, the slip effect of the wall surface is considered, and the simulation analysis is passed. Hydrodynamic pressure finger seal leaks within the same channel pressure distribution cloud diagram as shown in Figure 8, and seal medium leakage flow cloud diagram is shown in Figure 9.
In Figures 8(a) is is not conducive to the formation of fluid dynamic pressure film between the finger boots and the rotor, resulting in a decrease in the pressure in the leakage gap channel, and with the increase of speed, this change trend is more and more obvious. Figures 9(a), 9(c), 9(e), and 9(g) shows that when the pressure difference between the upper and lower reaches of the seal is 0.1 MPa, the ambient temperature is 500°C, and the rotor surface line speeds are 100 m/s, 200 m/s, 300 m/s, and 400 m/s. Regardless of the calculation results of velocity field streamline distribution of the sealing medium that avoids slippage, Figures 9(b), 9(d), 9(f ), and 9(h) calculated results of leakage velocity field streamline distribution when the wall slip effect is considered. As can be seen from Figure 9, the sealing medium flows from the end of the highpressure cavity into the leakage channel and flows out from the end of the low-pressure finger boot. As the speed of the rotor surface line increases, the streamline direction gradually tends to level. is is due to the effect of the upstream and downstream pressure differences. Under the action, the seal medium flows from the high-pressure cavity to the lowpressure cavity along the leakage channel. Under the influence of the rotor's circumferential high-speed rotation effect, the leakage fluid is affected by the circumferential shear flow effect due to the presence of the adhesive force of the seal medium, and the higher the speed, the more obvious the effect. erefore, it shows that the downstream streamline tends to level under the condition of ultra-high speed; that is, it tends to be consistent with the circular motion of the rotor. e velocity field calculation in Figure 9 also shows that when the rotor surface line speeds are 100 m/s, 200 m/s, 300 m/s, and 400 m/s, after considering the wall slip effect, the maximum velocity of the sealing medium in the circumferential leakage flow is reduced by 1.8 m/s, 40.1 m/s, 81.8 m/s, and 109.1 m/s. is is because the circumferential velocity of the sealing medium is related to the formation of the dynamic air film in the leakage gap. e greater the circumferential speed, the better the dynamic pressure effect. erefore, considering the slip of the wall surface, because the speed of the sealing medium along the circumferential motion decreases, it is not conducive to the formation of dynamic pressure gas film, which reduces the sealing effect. is is also very consistent with the stress reduction in Figure 8.
In order to analyze the influence of slippage on the sealing performance of hydrodynamic finger under different pressure differences, the change of sealing medium in the leakage channel of hydrodynamic finger seal was studied by simulation analysis when the temperature was 500°C, and the upstream and downstream pressure differences were 0.1 MPa, 0.2 MPa, and 0.3 MPa, respectively. As shown in Table 2, the value of slip ratio under different pressure difference conditions is calculated by theoretical formula. Figures 10 and 11 are the simulation results of gas film bearing capacity and leakage rate of hydrodynamic finger seal under different rotating speed and pressure difference conditions, respectively.   As can be seen from Figure 10, when the rotor line speed is fixed, the bearing capacity of the air film shows a gradual increase with the increase of the pressure difference between the upper and lower reaches of the seal. However, compared with the slip of the wall surface, considering the slip, the bearing capacity of the dynamic pressure film in the leakage gap appears to decrease, and this trend is more obvious with the increase of rotor surface line speed and upstream and downstream pressure difference. It can be seen that when the pressure difference between the upper and lower reaches of the seal is 0.1 MPa and the rotor line speeds are 100 m/s, 200 m/s, 300 m/s, and 400 m/s. Taking into account the displacement slip rate of the leakage channel, the bearing capacity of the gas film was reduced by 5.81%, 10.71%, 14.78%, and 17.39%, and the reduction was reduced as the pressure difference between the upper and lower reaches of the seal increased. e decreases were 1.45%, 2.79%, 3.76%, and 6.49%, respectively, when the pressure difference between the upper and lower reaches of the seal was 0.3 MPa.
is phenomenon shows that the higher the rotor speed, the more obvious the wall slip effect of the sealing medium in the microleakage channel and the more obvious the effect of the hydrodynamic finger seal performance on the wall slip under the pressure difference conditions of the same seal. However,    it also shows that the effect of pressure flow effect exceeds that of shear flow effect when the pressure difference between the upper and lower reaches of the hydrodynamic finger seal increases to a certain value. erefore, when the hydrodynamic finger seal is applied to the low-pressure differential high speed, the impact of the wall slip in the design cannot be ignored. When the pressure difference between the upper and lower reaches of the seal increases to a certain extent, the impact of the slip effect can be considered according to the comprehensive impact.
It can be seen from Figure 11 that the leakage rate of the hydrodynamic finger seal decreases gradually with the increase of the speed and increases gradually with the increase of the pressure difference between the upper and lower reaches of the seal. is is due to the pressure flow effect and shear flow effect, and the reason is obvious. At the same time, the results also show that the leakage rate of hydrodynamic pressure finger seal increases under the same working conditions compared with the calculation results without considering the slip conditions of the wall surface. And this trend is more significant with the increase of rotor surface line speed. It can be seen from the figure that, under the pressure 0.1 MPa and the maximum speed of 400 m/s, the leakage of the hydrodynamic finger seal increased by 14.06% as considering the slip conditions of the wall surface. In addition, under the same speed conditions, the pressure difference between the upper and lower reaches of the seal is 0.2 MPa and 0.3 MPa, and the leakage volume increases by 4.78% and 3.92%, respectively, which is consistent with the analysis results of the gas film bearing capacity, and it confirms that the low-pressure difference is high under the conditions of rotation speed. us, it is necessary to consider the slip effect of the wall in the design of hydrodynamic finger seal.
e simulation results show that the film bearing capacity is decreased to the maximum value while leakage rate is increased to the maximum at the speed of 400 m/s and pressure of 0.1 MPa. In order to further study and analyze the effect of wall slip on sealing performance at different temperatures, Figures 12 and 13 give the variation of film bearing capacity and leakage rate under typical temperature conditions. It can be seen from Figure 12 that the gas film bearing capacity shows a trend of decreasing and increasing with the increase of temperature, and the change trend of slip or not considering the wall surface shows the same, and 200°C is the turning point of the change trend. e results also show that the film bearing capacity decreases by more than 12.51% when slip on the wall is considered, and the maximum difference reaches 17.39% at 500°C as the temperature increases.
e results of the calculation in Figure 13 show that, with the increase of temperature, the leakage rate of the wall surface considering the slip or not shows an increasing trend, but considering the slip ratio of the wall surface, the leakage rate is higher than considering the slip of the wall surface. e difference between the wall slip and no wall slip also shows a tendency to reduce first and then increase, and the increase in the value of 500°C reached a maximum of 14.06%, which is related to the reduction in the bearing capacity of the gas film after the slip of the wall and the change in the size of the leakage channel. e results of the  analysis in Figures 12 and 13 show that, with the increasing influence of temperature on wall slip, the impact of wall slip effect needs to be considered when designing finger seal under high temperature application conditions, in order to design more accurate finger seal performance. In order to further analyze the effect of thermal effect and boundary slip on the sealing properties of finger, the displacement calculation results of the inner surface of finger boots are given as shown in Figure 14. Considering the slip effect of the wall surface, the temperature has a consistent trend of influence on the leakage gap of the finger seal. With the increase of temperature, the deformation of the finger seal boot shows the trend of first decreasing and then increasing. However, considering the boundary slip, the deformation value of the finger seal boots under the same temperature conditions is greatly reduced, which also shows that it is necessary to consider the impact of wall slip. At the same time, the results show that 200°C is a turning point in the trend of change. When the temperature changes between 25°C and 200°C, as the temperature increases, it is affected by the thermal deformation effect, and the leakage gap of the finger seal appears to decrease.

Conclusions
In this paper, the flow field model of hydrodynamic pressure finger seal gap is established based on the theory of microflow, and the slip effect of fluid seal is analyzed by CFX simulation; the key conclusions are summarized as follows.
(1) e hydrodynamic pressure finger seal leakage channel has microscale leakage flow characteristics. When the pressure difference is 0.1 MPa, the rotor line speed is 400 m/s, and the ambient temperature is 500°C and the slip rate has reached 27.28%. erefore, it is significant to consider the impact of the wall slip effect in the design of hydrodynamic pressure finger seal under high-speed conditions. (2) After considering the slip effect of the wall surface, the bearing capacity of the film decreases under the same working conditions, and the decrease is more obvious with the increase of the rotating speed. Under the above conditions, the bearing capacity of the gas film decreases by 17.39% compared with that without considering the slip, but the reduction value decreases with the increase of the pressure difference between the upper and lower reaches of the seal. It is explained that when hydrodynamic pressure finger seal is applied to low-pressure difference and high speed, it is necessary to consider wall slip in performance design. (3) Considering the wall slip effect, the leakage rate of hydrodynamic finger seal increases under the same working condition, and the increasing range is more obvious with the increase of rotating speed. Under the above conditions, the leakage rate increases by 14.06% compared with that without considering slip, which shows that the effect of wall slip in the design of hydrodynamic finger seal cannot be ignored, and it needs to be considered in the performance design.

Data Availability
e indispensable data used to support the findings of this study are included within the article. More detailed data are available from the corresponding author upon request.

Conflicts of Interest
e authors declare no conflicts of interest.