A Study of Fractal Deep-Hole Blasting and Its Induced Stress Behavior of Hard Roof Strata in Bayangaole Coal Mine , China

+e phenomena of strong pressure occurrences have been observed many times in the #311103 working face of the Bayangaole Coal Mine. Deep-hole blasting measures were used to relieve the pressure in order to decrease the danger levels of these strong pressure occurrences on the working face. +e blasting layouts proposed in this study differed from the conventional blasting layouts of a “straight-line” design by instead utilizing “triangular-fractal” and “deep-shallow-fractal” for the purpose of successfully driving the explosive efficiency and enlarging the roof-blasting range. +e fractal dimension of the “triangular-fractal” blasting layout was calculated as 1.1274.+e fractal dimension of the “deep-shallow-fractal” was calculated to be 1.556.+e fractal dimensions of both improved layouts were found to be larger than that of the “straight-line” blasting layout (1.0). In addition, the Mises stress evolution and the changed trend of the effective stress and strain of the observation points around the hole of the three layouts are analyzed and compared by LS-DYNA numerical simulation software. +e results indicated that the “deep-shallowfractal” blasting layout had the most effective blasting effects, followed by the “triangular-fractal” blasting layout. It was determined that the traditional “straight-linear” blasting layout had the least effective blasting effects of the three examined layouts. In summary, the implementations of the improved fractal blasting layouts in this study were found to be conducive to the enhancement of the blasting effects.


Introduction
With the progress of the working face in the Bayangaole Coal Mine, the hard roof is suspended in the goaf area.Due to the large strength and thickness of the mine's roof, a large area pressure phenomenon had occurred on the working face [1,2] which brought serious hidden hazards to the mine production processes [3,4].erefore, it was necessary to take effective measures for roof weakening in order to prevent potential accidents in the mine.At the present time, the most widely used roof-weakening techniques mainly involve hydraulic and blast-fracturing technology [5][6][7][8][9].Blast-fracturing technology is used to expand the crack zones, thereby destroying the integrity of the rock masses.
is results in causing the roof areas to fall more easily.
Many research studies and explorations regarding coal and rock blasting in coal mines have been conducted in China and internationally.Paine and Please [10] studied the destructive mechanical effects of the detonation gas on cracks in hard roof of coal mine and proposed an improved model of fracture propagation by gas during rock blasting; Xie et al. [11][12][13] used the fractal theory to establish the theoretical relationship between the dissipative energy of fractured rock in hard roof and the fractal dimension value of the block; Song and Kim [14] studied the entire process of rock damage by numerical simulation and described the initiation and propagation of cracks through different mechanisms and processes; and Trivino and Mohanty [15] have assessed single-hole blast-induced damage in a granitic outcrop through both numerical simulations with a combined finite-discrete element method (FEM-DEM) and controlled experiments.Lu and Tao [16] theoretically examined the velocities of the crack propagations driven by the detonation gases.Zuo et al. [17] carried out fracture mechanics analyses of the first roof falling presplitting blasting mechanisms of working faces.Banadaki and Mohanty [18] studied the damage of stress wave to roof rock through numerical simulation.
At present, the roof blasting of the coal mine working face has made a lot of progress, but due to the complex geological environment of deep rock mass, the roof of different coal mine working faces has different properties, so the traditional roof blasting method cannot fully adapt to all kinds of roof blasting.e phenomenon of strong pressure has been found to have occurred 27 times in the #311103 working face of the Bayangaole Coal Mine.In order to reduce the risks of these strong pressure occurrences in the working face of the mine and improve the blasting effects of blast holes during the mining process, the mechanism of deep-hole blasting in thick and hard coal mine roof was studied.
en, the blasting behaviors of the different blasting layouts were optimized and analyzed based on the fractal theory presented in this study.
e blasting process was simulated using LS-DYNA numerical simulation software in order to discuss the stress and strain evolution laws of the different blasting layouts.e goal was to obtain the optimal blasting layout and provide theoretical guidance for similar thick and hard-roofed mining conditions during presplitting blasting processes.

Engineering Conditions
e Bayangaole Coalfield is located in the southern section of the Hugierte exploration area, approximately 30 km west of the town Dabuchake in Wushen County.ere are 10 layers of coal deposits currently being mined in the coalfield, of which the 3-1 and 5-1 coal seams are minable within the entire area.e 3-1 coal seam has been determined to be stable.is seam has a thickness ranging from 3.09 to 7.00 m, with an average thickness of 5.74 m. e thickness increases gradually from north to south.e roof of the haulage roadway, and the return airway of the #311103 working face, was determined to be comprised of sandy mudstone measuring approximately 12.2 m; medium-grain sandstone measuring approximately 12.96 m; fine sandstone measuring approximately 3.74 m; and medium-grain sandstone measuring approximately 13.45 m, respectively.e stratigraphic structure of the areas is shown in Figure 1.
According to the blasting data provided by the Bayangaole Coal Mine, in the #311103 working face, strong pressure phenomena have been occurred 27 times, and the specific situations of "strong pressure phenomena" are listed in Table 1.It contains the location and date of the occurrence and the distance from the last strong pressure phenomenon.e phenomenon of strong pressure which had occurred within 50 m ahead of the #311103 working face was violent.erefore, blasting pressure relief measures were recommended to be utilized in the subsequent relevant areas in order to reduce the risks of strong pressure conditions on the working face of the mine.
In deep-hole blasting, there is a need to blast the key stratas.According to the key strata theory [19], the key strata of the 311103 working face roof rock layer is calculated by the following formula: Introducing the parameters of the roof rock layer into formula (1), the results are presented in Table 2. e two layers of the medium-grain sandstone above the #311103 working surface are calculated to be the key strata.erefore, the second layer of the medium-grain sandstone needs to be blasted in the deep-hole blasting process.Considering the difficulties in practical construction, the 45 °drilling angle is the easiest to implement, and the corresponding drilling depth is calculated to be about 45 m.
At the present time, blast-caving processes are often used to relieve pressure in hard and thick roof areas.However, long cantilever roofs will be formed behind the working face if caving is not in place, which potentially results in major hidden dangers for production and construction processes.Consequently, it is necessary to analyze the blasting mechanisms of the roof rock in mines, as well as predict the influence scope of the rock fragmentations, in order to determine the most effective blasting layout for the explosion of key strata in sandstone layers.
In order to calculate the theoretical blasthole spacing and the mechanical parameters of the medium-grain sandstone used in the simulation, it is necessary to conduct laboratory tests on the grain sandstone in the key layer of the roof.
In this research study, uniaxial compression and Brazilian splitting tests were carried out on the sandstone of the roof-blasting strata of the #311103 working face using a GCTS servohydraulic machine obtained from the laboratory of the China University of Mining and Technology (Beijing), as detailed in Figures 2-4.
e uniaxial compressive strength was obtained by taking the average value of the three specimens obtained with the GCTS.e tensile strength of the rock was indirectly obtained by the Brazilian splitting test method.e peak load of the three specimens was then converted into the maximum tensile stress of the specimen according to formula (2).e tensile strength of the sandstone was obtained by taking the mean value.
e peak loads of the three specimens in the Brazilian splitting test were separately substituted into formula (2) in order to determine the maximum tensile stress of the rock.
en, the tensile strength of the sandstone could be calculated by the mean value [20] as follows: where σ t represents the maximum tensile stress at the center of the specimen; P denotes the extreme pressure of the specimen's failure; d is the specimen's diameter; and t is the thickness of the specimen.e physical and mechanical parameters of the sandstone are shown in Table 3

Analysis of the Crushing Mechanism of the Deep-Hole
Blasting in Hard Roof.e effects of explosives on rock fragmentation mainly include the compression and tension processes of the blasting stress waves and the expansion processes following the detonation gases entering the rock cracks.For deep-hole blasting, the free surfaces of the roof areas cannot play the roles of reflection and stretching.As a result, the stress waves become reverberated and stretched by the joint surfaces and microcracks inside the rock masses.In this study, the damages caused to the rock due to stress waves are shown in Figure 5.Under the initial compression and tension of the stress waves, the preexisting fractures in the rock formed the initial cracks.
e detonation gases entered into the initial cracks, which then exerted vertical stresses resulting in further crack propagation.When the stress intensity factor K I at the crack tips reached the critical value of the rock fracture toughness K IC , the crack performed an "opening mode" propagation [21].K I could then be expressed as follows [22]: where P c is the quasi-static pressure of the explosive gases acting on the rock wall; a is the crack length in the rock mass; and Q denotes the stress intensity factor correction factor, which increased as the crack length a increased.It can be 4 Advances in Civil Engineering seen in formula (3) that, with the elongations of the fracture lengths, greater explosive gas pressure was generated and resulted in more opportunities for the propagation and extension of the fractures.e energy which had been produced by the explosion gradually dissipated in the form of stress waves and detonation gases.
e results of related studies have indicated that the fractures in the rock masses occurred when the instantaneous energy density on the fracture surface reached a critical value [23], and the critical energy density could then be calculated as follows: where σ denotes the stress waves acting on the rock mass; τ is the action time of the stress waves; C p is the wave velocity of the rock; and E represents the elastic modulus of the rock.As the action time, energy density, and intensity of the stress wave increased, the inclination of rock failure was more easily germinated.
From the perspective of fractures and energy, it was determined that improving the length and number of   Advances in Civil Engineering cracks in the fracture area at the initial stage of blasting, along with simultaneously slowing down the diffusion rate and attenuation of the stress waves, was beneficial to enhancing the blasting effects.

Analysis of the Influence Scope of the Deep-Hole Blasting in
Hard Roof.e deep-hole blasting of the roof was required to produce an increased number of cracks around the blast holes.ese cracks needed to penetrate between the adjacent blast holes in order to weaken the roof areas.en, by simultaneously considering the efficiency of the construction and economic factors, the crack zones generated by the adjacent blast holes were required to be in tangent with each other.e expressions of the blastholes intervals obtained from the Mises criterion were as follows [24]: where d denotes the blasthole intervals, m; σ R is the radial stress on the interface between the crushing zone and the crack zone, σ R � ����� � 2σ cd /B  ; ρ 0 and ρ represent the density of the explosives and rock mass, respectively, kg/m 3 ; D is the explosive velocity, m/s; C p denotes the longitudinal wave velocity, m/s; σ cd is the dynamic tensile strength of rock, MPa; α represents the load transmission attenuation index; β is the stress wave attenuation index; σ td is the dynamic uniaxial tensile strength of rock, MPa; b is the lateral stress coefficient; μ d denotes the rock dynamic Poisson's ratio, μ d � 0.8 μ; r b represents the radius of the blast hole; B denotes the property parameters of the explosives; K represents the decoupling coefficient; c is the adiabatic coefficient of the detonation products, which was generally set to 3; l e represents the charge axial coefficient; and n is the increment coefficient of the expanding detonation product colliding with the hole wall, which was generally set to 10.
According to the data of the Bayangaole Mine's working face, the density of the medium-grain sandstone was 2,130.8kg/m 3 ; C p was set to 3,300 m/s in the rock stratum; μ d was set to 0.178; and b was set to 0.126.e dynamic tensile strength of blasting σ td changed slightly with the loading strain rate, and σ td � σ t was set to 2.852 MPa. e dynamic compressive strength of the blasting σ cd varied with the loading strain rate, where σ cd � 1.8 and σ c � 79.1 MPa in this research study.Also, K � 1.3 adopted a continuous charge with l e � 1.
e parameter values were substituted into formula (5), and the crack zones were tangent with each other when the blasthole interval was 10.055 m.

eoretical Analysis of the Fractal Blasting Layout of Hard
Roof.During the process of the deep-hole blasting in the roof area, the fracture produced after the blasting was a fractal structure which had been formed by the fractal behavior of the evolution and agglomeration of the microcracks and joints.e relationship between the fractal dimension and the energy distribution and dissipation was determined to be as follows [17]: where a � lgE/lgr; b � 3 − lgC/lgr; C represents a material related constant; and r is the blasthole interval.By using formula (7), it was determined that the value of the fractal dimension was proportional to the dissipative energy density.en, with the increasing of the crack fractal dimensions following the blasting process, it was observed that the cracks which had been generated in the rock mass became more complex.e energy released from the explosion could be fully utilized, which led to more efficient blasting effects.
e fractal dimension of the self-similarity curve D f could be expressed as follows [25]: where N is the number of line segments with equal lengths in a fractal geometry and l/r is the similarity ratio, which refers to the ratio of the distance between the two ends of a geometric figure to the total length of these line segments.e fractal dimension characterized the irregular degree of the graph.As the fractal dimension D f increased, the formations of the cracks became more complex and developed fissures more easily.During the process of the blasting, the coal mine roof became weakened, which improved the fractal dimensions of the blast holes, and more cracks were generated after explosions.ese actions promoted the utilization rate of the blasting energy and attained the desired blasting results.

Calculation of the Fractal Dimensions in ree
Blasting Layouts

"Straight-Line" Blasting Layout of the Roof Areas (Original Layout).
In this layout, the blast holes were lined up in a straight line on the roof and were drilled into the rock above the coal seam at an elevation angle of 45 degrees.e lengths of the blast hole were 45 m, and the blast hole intervals were 10 m. e explosive loading position is shown in Figure 6. e length of the drug column was set at 8 m.
Since fractal geometry has self-similarity, l/r is the similarity ratio.In the "straight-line" blasting layout, three adjacent blast holes were regarded as a group of fractal graphics (Figure 7).
In the "straight-line" blasting layout, as well as the two fractal blasting layouts discussed later, three adjacent blast 6 Advances in Civil Engineering holes were regarded as a group of fractal graphics.e relevant parameters were obtained as follows: l � 20 m, r � 10 m, l/r � 2, and N � 2. en, the fractal dimension of the "straight-line" blasting layout was D f � 1.0.

"Triangular-Fractal" Blasting Layout of the Roof (Optimization Layout 1).
e blast holes in this layout were arranged in a double row dislocation (triangle) on the roof and had the same drilling lengths and angles as the "straight-line" blasting layout (Figure 8).It was considered that the blasthole position should be close to the angle of the wall and roof of the coal mine and reveal the fractal characteristics of the layout.Moreover, the row spacing was set at 2 m, and the blasthole intervals were set at 10 m. e length of the drug column was set to 8 m as in the straight-line layout.
In the "triangular-fractal" blasting layout, three adjacent blast holes were considered to be a group of fractal graphics (Figure 9).e relevant parameters were gained as follows: e length of the line segment r � ������� 10 2 + d 2

"Deep-Shallow-Fractal" Blasting Layout (Optimization Layout 2).
In this optimized layout, the blast holes were located in a straight line and drilled into the rock above the coal pillar at an elevation angle of 45 degrees, with the same angle as the "straight-line" blasting layout (Figure 10).e drilling lengths were alternately set as 45 m for the deep hole and 37 m for the shallow hole, with blasthole intervals of 10 m. e length of the drug column was set as 8 m.
In the "deep-shallow-fractal" blasting layout, three adjacent blast holes were defined as a group of fractal graphics (Figure 11).
In the "deep-shallow-fractal" blasting layout, N � 2 and r � 10 m were given, and the lengths of shallow and deep blast holes were 37 m and 45 m, respectively.Since the length of the drug column was 8 m, the midpoints of each drug column were taken as the calculating points.en, � 12.81 m, and l/r � 1.5613 were derived.e fractal dimension of the "deep-shallow-fractal" blasting layout is D f � 1.556.
e blasting layouts with larger fractal dimensions produced more cracks and thereby improved the blasting effects.e fractal dimensions of the three blasting layouts are shown in Table 4.

Simulation Analysis of the Deep-Hole Optimized Blasting Layouts for Hard Roof
In order to select the most effective blasting layout, the processes of the three blasting layouts were simulated using LS-DYNA.e Mises stress nephogram, an equivalent stress Advances in Civil Engineering map of the observation points, and the strain maps obtained from the simulation were analyzed, and a comparison was made.

Blasting Simulation Constitutive Model.
In Part 2, deephole blasting is believed to be conducted at the key strata.Two layers of the medium-grain sandstone are calculated as key strata.In order to effectively relieve the pressure on the top roof, the blasthole needs to be driven into the second layer of the key strata for blasting.e purpose of this simulation is mainly to study the influence of different blasting layouts on the blasting effects of the key layer, so only the key strata rock is simulated.e relevant parameters of the medium-grain sandstone applied in the simulation are listed in Table 5.
A coupling charge structure was used in this study's simulation process, and a JWL constitutive equation [26] was applied to express the explosion effects, as shown in the following equation: where A and B are the explosive parameters, GPa; R 1 , R 2 , and ω are the explosive parameters; P is the pressure, MPa; E 0 denotes the internal energy of the detonation product; and V is the relative volume of the detonation product, m 3 .e values of the specific parameters (s) are listed in Table 6.
In addition to the relevant blasting parameters in Table 6, the property of the explosive itself has a significant impact on blasting.e simulated explosive has a density of 1.3 g/cm 3 , a detonation speed of 4000 m/s, and a detonation pressure PCJ of 9.9 GPa.

Selection of Monitoring Points in the Numerical Model.
In view of the actual length of the roadway, large number of holes, and processing capacity of computer, this study selected three adjacent holes as the research simulation objects.
e size of the model was 80 m × 80 m × 30 m. ree observation points were utilized in each of the blasting layouts in order to monitor the processes of the stress and strain variations during the explosion.Figure 12 shows the positions of the monitoring points for the "straight-line," "triangular-fractal," and "deep-shallowfractal" blasting layouts.Advances in Civil Engineering

Simulation Analysis of the Stress.
In numerical blasting simulations, the Mises stress is generally used to describe the complex stress variations during rock blasting and to characterize the blasting e ects on the rock.e blasting e ects can be measured by analyzing the stress scope in the Mises stress nephogram, as well as the Mises stress density in the blasting area and the decay rate of the stress wave.e processes of the Mises stress evolution of the three blasting layouts are shown in Figures 13-15.
As can be seen in Figures 13-15, the Mises stress range of the three schemes became reduced with the changes in the blasting times, and the strength of the stress had also gradually decreased.is was due to the fact that the energy generated by the explosive which was used in the three blasting layouts had destructive e ects on the rock mass.
is led to rock fractures or the formation of cracks which then consumed most of the energy.At that point, the weaker stress waves were gradually transmitted to the far ends, resulting in the energy from the blasting to be further dissipated.
e analysis results demonstrate that the stress concentration area (warm tone area) range and amplitude of the "deep-shallow-fractal" blasting layout were the largest.Also, the stress wave decay rate in the deep-shallow-fractal layout was observed to be the slowest, followed by that of the "trianglefractal" blasting layout.Meanwhile, the "straight-line" blasting layout scheme displayed the smallest stress concentration area and amplitude, along with the fastest decay rate of the stress wave.It was concluded from the perspective of the Mises stress that the larger the fractal dimension of the blasting layout scheme, the slower the decay rate of the blasting energy.erefore, it was determined that the process was able to make full use of the energy applied to the rock, which was conducive to the expectations of the formation and expansion of cracks in the rock mass.
Figure 16 shows the variations of the equivalent stress over time for the three monitoring points.In this study, by   Advances in Civil Engineering comparing the peak values of the equivalent stress at the monitoring points and the speed of the decay rate, the resulting damages at the di erent positions in the blasting area could be accurately judged.
Figure 16 displays the equivalent stress variation trends of the three monitoring points.Following the explosion, the equivalent stress of the monitoring points rapidly increased to the peak value.en, the equivalent stress rapidly decreased and continuously oscillated.With the action of the blasting, the equivalent stress of the monitoring points gradually decreased and nally reached a zero value.Graphs (a), (b), and (c) represent the three monitoring points with   e differences in the stress peaks at the monitoring points were not obvious.e stress peaks of the three types of placement schemes at #1 monitoring points were all approaching 38 MPa. e peak values of the three kinds of blasting layout schemes in the #2 monitoring points were all close to 32 MPa and at the #3 monitoring points were all close to 28 MPa.ese results indicated that the closer the hole was to the monitoring point, the greater the peak value of the stress would be.e peak stress of the three monitoring points was found to be less than the tensile strength of the rock mass, which indicated that the diameter of the broken zone of the rock mass was less than 1 m.Also, the formation of the cracked area and the penetration of the fractures between the adjacent holes required a greater reflection of the tensile stress wave.
It was observed that after the first peak of the stress wave, the stress wave of the "straight-line" blasting layout decayed rapidly and tended to finally approach a zero value.Meanwhile, for the other two schemes, when their stress wave values attenuated to half of their peak value, a stress rebound phenomenon occurs.
en, their stress wave gradually decayed once again and eventually reached a zero value.In the middle and late stages of the blasting process, the equivalent stress of the three schemes was constantly oscillating, and stress rebound phenomena occurred.e stress rebound phenomena of the "deep-shallow-fractal" blasting layout was the most conspicuous, followed by the "triangle-fractal" blasting layout.However, the phenomena of the stress rebound of the "straight-line" blasting layout were not obvious.ese findings indicated that the stress wave of the blasting layouts with high fractal dimensions would be continuously reflected in the rock fractures and thereby have sustained effects on the rock mass instead of spreading toward the far end.is would contribute to the desired expansion of the crack zone and the formations of penetrating cracks between the adjacent blast holes.
In this study, by combining the Mises stress nephogram and the equivalent stress nephogram of the monitoring point, it was found that the larger the fractal dimension of the blasting layout was, the larger the stress concentration zone of the blasting stress wave would be, and the longer the duration would be. is would also result in more obvious monitoring point stress rebound phenomena.erefore, the fractal blasting layout could potentially improve the fractal dimensions of the blasting, as well as increase the crack zone, and enhance the possibility of crack extenuations in multiple directions.Furthermore, the increases in the fractal dimensions of the blasting layout could result in increasingly complex initial cracks, which would have reflective and tensile effects similar to the free surfaces, and cause the cracks to expand further.After the crack expansion, the blasting gas would enter the initial fractures and further expand them.In this way, the new complex fractures would have the continuous oscillating tensile action of the stress waves. is would prevent the stress waves from diffusing outward and result in the energy fully acting within the fractures, thereby prolonging the effects of the stress waves.

Simulation Analysis of Blasting Strain Area.
It is known that strain will occur when blasting actions affect rock masses, and the rock masses become damaged as the strain reaches its limit.In order to compare the blast effects of the different blasting layouts examined in this study, the magnitudes of the strain values around the blast holes (warm tone depth) and the geometric characteristics of the observed effective strain regions were also taken into consideration.
e effect dimensions of the "triangle-fractal" and "deepshallow-fractal" blasting layouts were a vertical-hole surface and a parallel-hole surface, respectively.In order to intuitively compare the effects of the different blasting layout schemes on strain regions, the two types of fractal blasting layout schemes were compared with the traditional "straight-line" blasting scheme.It was observed that the "straight-line" and "triangle-fractal" blasting layouts could be compared by the angle of the vertical-hole section (Figure 17(a)).e "straight-line" blasting layout and "deepshallow-fractal" blasting layout could be compared with the angle of the parallel-hole section (Figure 17(b)).e strain ranges of the three schemes were found to gradually increase with the blasting times, and the strain value in the area between adjacent blastings holes also gradually increased (warm tone region).In this study, by comparing the strain regions of the "straight-line" and "triangle-fractal" blasting layouts, it could be seen that there was a high strain region in the "triangle-fractal" characterized by a zigzag-shape line.Meanwhile, the high-strain region of the "straight-line" layout was a line shape.In addition, the "triangle-fractal" arrangement displayed large strains in the middle of two distant holes.
ese results indicated that the fracture bifurcation displayed by the "triangular-fractal" scheme was more likely to be bene cial to the crack propagation.It was also found that the e ective strain range of the "triangle-fractal" blasting layout was larger than that of the "straight-line" blasting layout, and the blasting e ects were superior.
In this study's comparison of the "deep-shallow-fractal" and "straight-line" blasting layouts, it was found that the highstrain region formed by the "deep-shallow-fractal" blasting layout was also in a zigzag-shape line.A larger strain region had also been formed between two distant points in the "deepshallow-fractal" blasting layout.ese ndings indicated that the "deep-shallow-fractal " blasting layout had better energy utilization e ects and that the stress waves and exploding gases had acted more fully on the rock mass.
In accordance with the simulation results of the stress and strain, it was found that the larger the fractal dimension was, the slower the attenuation speed of the stress wave would be,

12
Advances in Civil Engineering and the more obvious the changes in the strain values would be. is was observed to be helpful in the breakage of the rock mass and the penetrations of the resulting fractures.erefore, the entire weakening e ects of the blasting on the coal mine's roof areas could be e ectively improved.

Conclusions
(1) e mechanism of the deep-hole roof blasting and crushing in the Bayangaole Coal Mine were analyzed in this study.e e ectiveness range of the explosives was theoretically analyzed, and the reasonable distance between the adjacent holes was determined to be about 10 m. (2) While conducting an optimization analysis of the layout of the blasting holes based on a fractal theory, this study proposed two optimization blasting layouts: "deep-shallow-fractal" and "triangle-fractal" blasting layouts.e results showed that the fractal dimensions of the traditional "straight-line," "triangle-fractal," and "deep-shallow-fractal" blasting layouts were 1.0, 1.274, and 1.556, respectively.It was determined that the larger the fractal dimensions were, the more the cracking bifurcation opportunities would be created, which resulted in increased quantities of fractures, as well as higher complexity in the fracture areas.
(3) In this study, LS-DYNA software was used to simulate the laws of the stress and strain evolutions in the three blasting layout schemes.e results showed that the "deep-shallow-fractal" blasting layout had the most e ective blasting e ects, followed by the "triangle-fractal" blasting layout.However, the "straight-line" blasting layout was found to have the least e ective performance in the simulation.Also, the simulation results veri ed that, from the perspective of the stress and strain values, the larger the value of the fractal dimension was, the higher the blast energy utilization rate would be, and the more e ective the roof-blasting process would be.

Data Availability
e gures and tables data used to support the ndings of this study are included within the article.

Figure 5 :
Figure 5: e e ect of stress wave on rocks.

Table 1 :
#311103 working face strong pressure phenomena statistical table.

Table 2 :
#311103 working face key strata calculation statistics table.

Table 3 :
Physical and mechanical parameters of sandstone.

Table 4 :
Fractal dimensions of the di erent blasting layouts.