Cracking Mode Analysis of Crack Initiation in Rocks under Uniaxial Compression

Crack initiation is related to the behavior of the preexisting microcracks within a rock specimen, which suggests the specimen starts to fail. .e determination of crack initiation stress is important for identifying the elastic stage and related mechanical parameters. Uniaxial compression tests with acoustic emission monitoring were performed to study crack initiation for tight sandstone, loose sandstone, and granite. .e evolution of the cracking mode, i.e., the statistics of the cracking mode under compression, was obtained through modified acoustic emission parameter analysis. Based on the logarithm of the acoustic emission parameter (LAEP), a cracking mode analysis (CMA) method is proposed and used to determine the crack initiation stress. Results from the tests indicate that the crack initiation stress between the same rock specimens obtained by CMA is very close. .e mean ratio of crack initiation stress to compression strength is 0.45, 0.34, and 0.35 for tight sandstone, loose sandstone, and granite, respectively. According to the results of CMA, crack volumetric strain (CVS) method, and lateral strain response (LSR) method, there is no big difference among those methods in tight sandstone and loose sandstone. In granite, the results obtained by CMA are close to those obtained by CVS, but smaller than those obtained by LSR..eCMA interprets the initiation of cracks from the fracture behavior of microcracks and is an objective method to determine the initiation stress.


Introduction
Unlike metals, rocks usually contain many microcracks.As early as the 1920s, Griffith proposed that such microcracks were capable of influencing the mechanical properties of rocks subjected to applied loads [1].Under compression conditions, the failure process of the ultimate strength is currently divided into four stages: (1) crack closure stage, (2) elastic deformation stage, (3) crack stable growth stage, and (4) crack unstable growth stage [2,3].Many researchers have offered descriptions of the cracking modes during the process of rock failure [4,5].For rocks, the crack initiation stress is the first stress threshold for the stage division of the failure process and also plays a critical role in the determination of the mechanical parameters.Some studies have found that crack initiation in rock is closely related to spalling problems that occur during underground construction [6][7][8].
Since Brace first presented an approach to determine the crack initiation from volumetric strain in 1966, various crack initiation determination methods have been proposed [9].For example, Lajtai and Stacey suggested different crack initiation point determination methods based on the radial strain [10,11]; another crack initiation point determination method was proposed by Diederichs based on the variation in Poisson's ratio [12].Martin identified the volumetric strain of cracks according to differences between volumetric strain and elastic strain and then determined the crack initiation through the changes in the volumetric strain of the cracks (CVS) [13].However, these methods rely on the determination of both elasticity modulus and Poisson's ratio, and the parameters are affected by some subjective factors that induce errors [14].At present, the lateral strain response (LSR) method proposed by Nicksiar and Martin can determine such point in a simple and effective manner [15].e cumulative acoustic emission hit (CAEH) method has been developed for the determination of the crack initiation stress [16].Additionally, the influences of subjective factors can be excluded by using those two approaches to objectively identify the crack initiation point [17].
Many researchers believe that rock failure is closely related to the mechanical behavior of microcracks, but there has been a lack of effective observation methods.In the earliest studies of rock failure, the researchers used optical microscopes to observe microcrack morphology and structure [18].With advancements of the technologies, computed tomography (CT) and scanning electron microscopy have been introduced to study the internal damage processes of rock specimens under stress [19,20].Nevertheless, applications of these techniques have some limitations.Continuous monitoring cannot be easily realized, and a considerable amount of time is required to conduct postprocessing and obtain the final test results.In contrast, acoustic emission (AE) testing provides advantages without affecting the loading process [21].Acoustic emission is the transient elastic waves within a material, caused by the rapid release of localized stress energy [22].Many researches have used AE techniques under uniaxial/triaxial conditions to study the failure of brittleness materials [23][24][25].AE testing has also been applied to interpret the cracking modes of microcracks in laboratory tests [26][27][28].A cracking mode study based on a signal-based analysis needs multiple sensors and takes much time for postprocessing [29].Moreover, the analysis is often limited by the size of the rock specimens.A parametric AE analysis can be more convenient than signal-based analysis to identify cracking modes.Hence, a cracking mode analysis based on AE can be chosen to identify the crack initiation.
Although many methods for measuring crack initiation stress have been proposed and some models have been developed to interpret the crack initiation from volume change of microcracks, there is no accurate description of the fracture behavior of the microcracks.In this paper, the evolution of the cracking mode in the uniaxial compression test is studied by using AE parameters, and the crack initiation is interpreted from the fracture behavior of microcracks.An objective cracking determination method based on cracking mode analysis (CMA) is proposed, and its effectiveness is verified by comparing with the other method.
is proves that it is reasonable to analyze the failure process of rock from the microcracks fracturing process.And it also provides a new angle for the determination of the other characteristic points of rock damage under compression.

Uniaxial Compression Tests.
e test evaluated the specimens from three rock types: tight sandstone, loose sandstone, and granite.
e basic properties of the rock specimens are presented in Table 1.While the tight sandstone specimens were acquired from coring at 3000 m underground, the loose sandstone and granite specimens were obtained from outcrops.Following the recommended standard of the International Society for Rock Mechanics (ISRM), the specimens were processed into cylindrical shapes with diameters of 25 mm and lengths twice the diameter, as presented in Table 1.
e deviations between parallel top and bottom surfaces of any specimen were not allowed to exceed 2.5%.
During the uniaxial compression test, an AE acquisition instrument and two 7.8 mm diameter sensors were used to collect the AE waveform signals; the resonant frequency of the sensors is 150 kHz.e signal preamplifier of the AE monitoring system was 40 dB, and the corresponding signal sampling frequency was 5 MHz.After an ambient noise test, the measurement threshold value was set to 35 dB. e results of the three-point bending test show that, in the size range of the tested samples, the effect of the distortion on the AE parameters is not significant to the result of the cracking mode analysis (see Supplementary Test S1 in Supplementary File S1 online).
As shown in Figure 1, the radial and axial directions of the test were measured by linear variable differential transformers (LVDTs).A copper sleeve was bonded to a specimen surface that had been polished, and ultrasound couplant was then applied onto the surface of the AE sensor so that it could be mounted inside the copper sleeve.To diminish the disturbances from the friction generated between the specimen ends and compression plates on the test results, both ends of the specimen were lubricated with petrolatum.e uniaxial compression test was performed by a triaxial servo compression test system.e designed confining pressure was 200 MPa.e maximum axial load was 10000 kN, and the test ranges of the axial and radial deformations were from −2 mm to 2 mm.e signals such as the confining pressure, axial load, displacement, and strain were collected and controlled by the DOLI automatic data acquisition and control system.During the entire test process, displacement was employed to maintain the loading speed of 0.02 mm/s.

Cracking Mode Classification Based on Modified Parametric AE Analysis.
During the process of rock failure, numerous microcracks are activated, consequently generating many AE signals due to the release of strain energy.e parameters of the AE signals vary with the cracking modes.Both average frequency (AF) and rise time over the maximum amplitude (RA) can be used as indexes to study the cracking mode through the differences between longitudinal and transverse wave velocities and the influence of different cracking modes on the frequency [30].By referring to the recommended testing standard of concrete materials stipulated in the International Union of Laboratories and Experts in Construction Materials, Systems and Structures (RILEM), RA and AF can be defined as follows: RA is the rise time over the maximum amplitude and AF is the ratio of AE ringdown-counts over the duration of the signal [31].e rise time (RT) is the duration from the onset time of the signals until the moment that the amplitude peaks.After the AE parameters have been treated with a moving average of per 0.1 second, they are distributed within an AF-RA coordinate plane.Subsequently, the cracking modes of the microcrack events can be determined according to the relative positions of the cracking mode classification lines (CMCLs) and AE parameters [32].
To study how the evolution of the cracking mode changes during rock loading, it is necessary to consider the variations in the AE parameters in the time domain.e AF-RA-time three-dimensional coordinate system based on the parametric AE analysis is too complex to be analyzed.

Advances in Civil Engineering
Moreover, the existing method can only divide the cracking mode into two types, tensile-mixed and shear, and results for the same cracking mode are not easily compared.To solve this problem, we propose a parameter called the logarithm of the AE parameter (LAEP) (Equation ( 1)).For various microcracks with dissimilar cracking modes, the ratio of AF to RA may vary considerably.To better describe the trend of the differences in this ratio, the AF/RA ratio is processed logarithmically: LAEP � log 10 AF RA  . ( During uniaxial compression testing, crack initiation occurred and was followed by propagation and interconnection as the load increased.In addition, many AE signals were generated during this process.e characteristics of these AE signals changed due to the differences in the focal mechanisms.Although the CMCL value for each specimen is not easy to determine, a decrease in the LAEP suggests that the cracking mode has a shear failure trend, while an increase in the LAEP suggests that the cracking mode has a tensile or mixed mode trend.In addition, it can be inferred that not only the CMCL values may vary, but the upper and lower limits of the corresponding LAEP values may also change due to the differences in the compositions and microstructures of the rock types.
Combine with Ohno's research [33], the distribution of the LAEP values is divided into two parts that correspond to different fracture behaviors, as shown in Figure 2. When stress is applied normally to the microcrack, the microcrack cannot be activated, and there is no AE signal.With a change in the stress, compression-shear failure occurs along the microcracks, and the LAEP increases gradually from a minimum value.When the LAEP is above the CMCL, the tensile-shear failure will occur.In addition, the maximum value of the LAEP is obtained when pure mode I fracturing occurs.
e cracking mode analysis based on LAEP can be used to not only distinguish fracture behaviors but also perform an analytical investigation on the mechanical responses of rocks during the whole loading process.

Proposed Cracking Mode Analysis (CMA)
Method and Verification

Cracking Mode of Microcracks under Compression.
Due to the influences of various diagenetic conditions, there exist many pores and microcracks in rocks.Considering that the tensile strength of a rock material is generally far less than its compressive strength, tensile failure will preferentially occur in the pore structure under compression.
Compared with this pore structure failure, microcracks are considerably more complicated.Hence, the mechanical behavior of a single crack under triaxial compression needs to be studied.e microcracks will be closed first when rock is under compression.As shown in Figure 3, the stress state along a closed fracture plane will be discussed below by taking a twoprincipal-stress state microelement in the sample.
Under the action of stresses perpendicular to the fracture plane, the stress of the friction generated on this plane can be denoted as e effective shear stress of this plane is τ ef � τ xy − τ n .
For a closed fracture plane under compression, only mode II fracturing is assumed, and the stress intensity factor at the crack tips is expressed as . When K II � K IIC , the crack begins to propagate; the following equation can be established for the critical condition: e function must satisfy the condition of 0 . σ c is the critical shear stress of the crack, and f is the coefficient of friction.K IIC is the mode II fracture toughness and is usually a material constant.
At the microscopic scale, the differences in the microcrack lengths are small enough and can be approximated as a constant value.Here, the stress of the friction on the crack surface is assumed to be uniform; then, f is only associated with the material and is also a constant.So through equation ( 4), we can get the curves between critical shear stress and crack dip at different stress ratios as shown in Figure 4, and σ c is normalized.Figure 4 reveals that as k increases from negative to positive, the minimum value of σ c , which is the critical shear stress of the microcrack, also increases.When k is negative and the microelement is under a lateral tensile stress, the stress-fracture dip curves are asymmetrical; however, if k is positive, which indicates that the microelement is under a lateral compressed stress, these curves are symmetric.With a continued increase in stress, shearing occurs along the microcracks at successive angles.e curves in Figure 4 clearly show two limit values of the microcrack fracture dip, β min and β max , signifying that, theoretically, no mode II fracturing occurs along microcracks with dips outside of this range, no matter the stress magnitude.During the loading of a uniaxial compression test, the initiation of many microcracks with dip angles between β min and β max occurs as the stress σ increases.When shear failure occurs along nearly all the microcracks within the range [β min , β max ] and σ reaches a certain value, crack initiation begins.
Additionally, Figure 4 indicates that when k > 0, the critical stress is infinite and the dip angle approaches β min .In this case, mode II fractures are less likely to be activated.However, the cracks usually show strong instability, and tensile fractures may also form because of the decrease in the fracture dip β. e probable causes of such a phenomenon are described as follows.When β is sufficiently low, the microcracks cannot be considered closed.And there is no friction between the fracture planes; in this case, microcrack opening often increases with additional tensile stress, which can cause mode I fracturing.
e critical stress will reach a minimum when the microcracks are at a certain angle.At this moment, zσ/zβ � 0 and z 2 σ/z 2 β > 0. erefore, an expression for the initial crack angle can be acquired: As shown in Figure 5, the initial angle β σ−min monotonically changes with f, which is the friction coefficient of the fracture plane and is independent of the stress ratio k.Advances in Civil Engineering erefore, variations in f affect β σ−min without changing the functional relationship between σ and initial angle.e dip range [β min , β max ] of cracks in specimens from the same rock should be the same, and the crack initiation stress should be well determined, provided that the crack initiation stress is related to only the material.

Crack Initiation Determination by CMA Method.
As mentioned above, shear failure of microcrack under compressive stress occurs sequentially with a certain range of microcrack dip angles.Such a process is not completed until all those microcracks have been activated.In this case, the microcracks inside the rock can be considered fully initiated, corresponding to crack initiation.erefore, it may be feasible to distinguish different rock failure stages by analyzing the cracking modes of microcracks during compressing.e cracking mode analysis is based on the analysis of LAEP.As the uniaxial compression increases, shearing successively occurs along the closed microcracks within a range of dip angles because of differences in the stress states of the fracture planes; the corresponding LAEP thus gradually decreases.After the LAEP and the corresponding cracking mode were analyzed, the variations in the LAEP during loading were utilized to study the internal microcrack responses of the rocks and the impacts of these responses on the mechanical behaviors of the specimens.
Figure 6 shows the time-varying LAEP distribution and variations in stress for the three rock types.
e figure provides three representative test results, while the results of all ten rock specimens can be found in Supplementary Figures S2 to S4 in Supplementary File S1. Figure 6(a) shows that the LAEP values of the tight sandstone vary from 0 to 4. During the early stage of loading, the LAEP distribution is relatively concentrated; it fell slightly within a short time period, which was followed by an upward trend.is indicates that, in this stage, the microcracks are gradually closed, and the cracking mode changes from tensile to shear.With the increase in loading, the distribution of LAEP is more disperse, and the lower envelope of LAEP appears to decrease first and then increase.Generally, the macrocracks of the rock are assumed to form when the ultimate strength is reached; then, the friction between fracture planes begins to play a dominant role.Hence, the AE signals are mainly generated by shear slip after the stress has reached the ultimate strength.at is the main reason the distribution of the LAEP value is more concentrated and obviously decreases after the ultimate strength when the stress is close to the ultimate strength.In Figure 6(b), the distribution of the LAEP for the loose sandstone is more disperse and greater than that of the tight sandstone, ranging from 0 to 6. Due to the existence of a large number of pores in the loose sandstone, tensile failure caused by pore failure occurs during loading.Despite the strength limit, LAEP still has a higher value.Although the load is close to the ultimate strength, there still exists a large value of LAEP.Similar to those tight sandstones, the lower envelope of LAEP also appears to decrease first and then increase.Figure 6(c) shows that the distribution of LAEP in granite samples is more concentrated, ranging from 1.5 to 3.5.Overall, the variation characteristics are similar to those of loose sandstone, but the minimum of the lower envelope appears earlier.
Whatever the rock type is, a comparison of the diagrams in Figures 6(a)-6(c) shows that the variations in the LAEP envelope tend to first decrease and then increase.Additionally, the minimum envelope value is sometimes recorded during the early stage of loading.Considering that such cases always happen when the rock is in an unstable loading stage, these minima may be caused by friction at the sample faces.Without regarding the minimum envelope values at the beginning, the lowest point of the envelope during the loading process also signifies that microcracks shearing has nearly finished in the rock.e stress that corresponds to the lowest point of the LAEP envelope is the crack initiation stress.After crack initiation, the tensile cracks parallel to the direction of the maximum stress form at or near both ends of the microcracks.e propagation of these tensile cracks corresponds to a stable propagation stage.
According to the above analysis, the changes in the LAEP are consistent with the mode of the microcrack failure within the rock.e LAEP is correlated with the stress state of the microcracks because the lowest point of the LAEP envelope corresponds to the sufficient occurrence of microcrack shear failure within the rock.
e effective shear stress on a microcrack plane during mode II fracturing is defined as , where K IIC refers to the roughness constant of the mode II fracture.Furthermore, assuming that the crack length is finite, τ c is also a specified value at the time of crack shearing.erefore, no matter how σ changes, the shear strength of the crack τ c remains unchanged and, thus, does not impact the changes in the LAEP during the test.
As previously described, as σ increases, the microcracks under compression successively shear according to the dip angles.For microcracks of an identical length, mode II fracturing occurs when τ ef reaches τ c on the fracture plane.
e effective stress along the fracture plane can be expressed as τ ef � τ xy − τ n .Although the shear strengths of the cracks are identical when mode II fracturing occurs, equations ( 2) and ( 3) indicate that τ xy and τ n will vary with the crack dip angles and applied stress.Furthermore, considering τ n � τ xy − τ c � fσ n , the LAEP is inferred to be associated with τ n : LAEP ∝ 1/τ n .In other words, the LAEP may be affected by the force of friction along the cracks and the stress applied normal to the fracture plane.To determine the specific functional relationships, these parameters need to be further theoretically and experimentally studied.

Comparison and Verification.
e mechanical parameters and crack initiation stress measured under uniaxial compression for the three rock types are listed in Table 2. "CMA" in the table represents that the crack initiation stresses are calculated using the CMA method described above.e crack initiation stresses, determined by the CVS method proposed by Martin [13] in 1993 and the LSR [15] method, are also presented in Table 2. Figure 7 shows those different methods for determining crack initiation stress of rocks under uniaxial compression.e "Stress ratio" in the table denotes the ratio of the crack initiation stress to the compression strength.e mean value of the stress ratio is the ratio of the mean crack initiation stress to the mean compression strength.
In Table 2, due to the difference in the coring depth, the mechanical parameters of tight sandstones vary in both elastic modulus and ultimate strength.However, significant differences in the elastic modulus among the three types of rock can be observed.e loose sandstone has the highest degree of porosity, and its mean elastic modulus is the lowest, 5.4 GPa.
e granite has the highest mean elastic modulus, 40.4 GPa. e compressive strength is consistent with the elastic modulus.e highest is granite, 116.4 MPa, followed by tight sandstone, 85.6 MPa. e lowest is loose sandstone, 32.5 MPa.In addition, the strength of the loose sandstone specimens shows some difference between specimens D and E and specimens F and G.Such differences may be caused by variations in the coring direction.Specimens D and E were cored perpendicular to the sedimentation direction, while specimens F and G were cored parallel to the sedimentation direction.
As shown in Figure 8, comparing the initiation stress of different rock types calculated by using the CMA method, it has great difference, but the minor differences between stress ratios of different rock types.ose ratios are 0.34, 0.45, and 0.35 for tight sandstone, loose sandstone, and granite, respectively.And then, we compare the results obtained by different methods.For tight sandstones, there is little difference in the mean value of the crack initiation stress calculated by different methods, which is maintained at approximately 40% of the ultimate strength.For loose sandstone, the mean value of the crack initiation stress  Advances in Civil Engineering calculated by the CVS method is slightly higher, but it is not more than 40% of the ultimate strength.For granite, the result of the LSR method is obviously higher than that of the other two methods, reaching approximately 50% of the strength limit.
A more intuitive comparison among the results obtained from these three methods is shown in Figure 8. e results of all three methods are similar for the crack initiation stresses of the tight and loose sandstones.As mentioned before, for granite, the results of the LSR method are clearly different from the results achieved by using the CMA method and CVS method.Such a difference may exist because the mineral constituents and internal structures of the rock types are distinct, which requires further study and determination.e abovementioned results verify not only the validity of the microcrack model but also the feasibility of using the LAEP to determine the crack initiation points.

Conclusions
Failure of rocks under compression is of great importance for building and underground construction.However, the initiation and subsequent propagation of the cracks are important to the damage and failure of a material.In this paper, the cracking mode of microcracks initiation within rocks under uniaxial compression is studied theoretically and experimentally.eoretical analyzes show that not all the closed microcracks will be activated by shear during the compressing process of rock specimens.Shear slip of the microcracks occurs in sequence when the microcracks dip varies in a certain range.If these microcracks are completely activated by shear, the crack initiation begins.At this point, the critical stress of shear failure reaches the maximum.After that, the microcracks begin a stable tensile propagation stage.
A modified parametric AE analysis method was proposed in this paper to analyze the cracking mode evolution of microcracks during the uniaxial compression tests.e key of this method is to propose a new parameter LAEP that is sensitive to the fracture mode.e test results reveal that successive crack shearing is accompanied by a gradual decrease of LAEP, which ultimately reaches a minimum.In conjunction with the theoretical analysis, the minimum value in the envelope of LAEP in fact corresponds to the crack initiation point.
Although the compressive strength and crack initiation stress of three rock types are quite different, the ratio of crack initiation stress to compressive strength is very close.ose ratios are 0.34, 0.45, and 0.35 for tight sandstone, loose sandstone, and granite, respectively.By comparing the results of the CMA method with CVS and LSR methods, the validity of this method is verified.is study demonstrates the feasibility of interpreting crack initiation from a microperspective, and a new CMA method has been developed for objective determination of the crack initiation stress.

Figure 3 :
Figure 3: Internal stress state of the rocks near the microcrack.

Figure 4 :
Figure 4: Relation between critical shear stress and crack dip at different stress ratios.

Figure 2 :
Figure 2: e definition of the parameter LAEP.

Figure 5 :
Figure 5: Relationship between friction coefficient and initial angle of crack formation.

Table 1 :
Basic properties of the rock specimens.

Table 2 :
Comparisons of the results used for determining the crack initiation stress.