Application of a Combined Homogenate and Ultrasonic Cavitation System for the Efficient Extraction of Flavonoids from Cinnamomum camphora Leaves and Evaluation of Their Antioxidant Activity In Vitro

A free-of-dust pollution extraction method combined-homogenate and ultrasonic cavitation system, namely, homogenate-combined ultrasonic cavitation synergistic extraction (HUCSE), was proposed for the efficient extraction of flavonoids from Cinnamomum camphora leaves. Response surface methodology of Box–Behnken design was employed to optimize the HUCSE process, and the optimum operation conditions attained with an extraction yield of 7.95 ± 0.27 mg/g were ethanol concentration 76%, homogenate/ultrasonic time 25 min, solvent-to-solid ratio 22 mL/g, and ultrasonic power 240 W. A second-order kinetic mathematical methodology was performed to depict the behaviors of HUCSE and heat reflux extraction method. The results suggested that the developed HUCSE is an efficient and green method for the extraction of C. camphora flavonoids or other plant natural products, where the obvious higher parameters of extraction capacity at saturation, second-order extraction rate constant, and original extraction rate were obtained when compared to the heat reflux method. The antioxidant activity assays in vitro showed that the C. camphora flavonoids possessed strong antioxidant activity and are promising to be applied as a natural alternative antioxidant.


Introduction
Natural products have gained great interest as natural alternatives to substitute the traditional synthetic compounds for health purposes as their remarkable health-promoting activity and consumer preference for the cleaning labels [1,2]. Specially, natural products even have been considered as an abundant source for drugs production, thanks to their chemical structures diversity that synthetic compounds cannot compare [3]. As an important member of plant natural products, flavonoids are commonly occurring in nature with variant phenolic structures [4]. Flavonoids are well known for their versatile health benefits that mainly ascribe to their antioxidant activity [5], anti-inflammatory activity [6,7], and antitumor activity [8][9][10].
Cinnamomum camphora is an evergreen tree, which is widely distributed in Southern China as a Chinese folk medicine for the cure of many diseases [11]. C. camphora is even extensively cultivated in Jiangxi province as a landscape tree species and an economic crop for the production of essential oil and camphor [12]. Many recent studies which highlighted the utilization of C. camphora are mainly on essential oils used for their antifungal and insecticidal activities [13][14][15], and the other bioactive compounds are rarely involved. Notably, previous studies demonstrated that flavonoids are indwelling in C. camphora leaves with remarkable antioxidant activity and antibacterial activity [16][17][18]. Moreover, a previous study suggested that scientific harvesting of C. camphora leaves at regular intervals facilitates C. camphora to grow vigorously [19], so it is an ideal source for the separation of flavonoids.
Generally, plant materials are ground to powders using mechanical disintegrators prior to the subsequent extraction process for sufficiently obtaining the target compounds.
Among the physical smashing ways, homogenate is an effective technique as it possesses many inherent merits (e.g., high-speed mechanical shearing effect, agitating, pulverization, and no powder pollution), which is conducive to the dissolution of plant bioactive compounds into extraction solvent [20,21]. Extraction of flavonoids is traditionally attained by techniques involving heating, boiling, or refluxing. However, these techniques have been pointed out to be subjected to the shortcomings of low extraction efficiency on account of hydrolyzing, ionizing, and oxidation reaction during the natural bioactive compounds extraction processes as well as large volume of solvent consumption and long extraction time consumption [21][22][23][24]. In this respect, an environmentally friendly process associated with the maximization of the target compounds yields with minimum degradation, resulting in the most effective constituent at a low cost would be ideal [25]. Innovative techniques on the basis of ultrasonic-assisted extraction have been employed to separate plant natural products and have showed great potential on obtaining high valuable target constituents [26][27][28][29]. e proposed principle of the ultrasonic-assisted extraction method is sonochemistry and mechanical effects induced by ultrasonic cavitation. For one thing, high strength ultrasonic waves can cause pressure fluctuations when they propagate through liquid medium which can instantaneously give rise to plenty of vacuum-filled cavitation bubbles [30]. ese bubbles are highly fragile and unstable and can implode abruptly within a few milliseconds. Accompanying with the collapse of cavitation bubbles, local temperature and pressure will increase, which favors for solvent circulation and penetration within the cellular plant materials as well as improving mass diffusion rate, thus enhancing the extraction performance [31]. In addition to the cavitation phenomena of sonochemistry, the mechanical effect generated by microstreaming and microturbulence facilitates cell walls breaking mechanically and hence promoting the release of target compounds from the plant materials into the extraction medium [32]. Apart from the merits in decreasing extraction time, saving energy, and improving the extraction yields, easy operation, and low cost, the remarkable benefit of ultrasonic-assisted extraction is that it is beneficial to thermolabile target compounds extraction with almost no degradation [33]. us, developing a reliable, highly efficient, and green extraction methodcombined homogenate and ultrasonic cavitation for obtaining C. camphora flavonoids is much necessary. e response surface method (RSM) is an efficient statistical optimization methodology which just needs a few numbers of experimental trials to investigate multiple variables and their interactive effects [34]. RSM is useful for optimizing complex procedures in which response values of interest are affected by various parameters, and the objective is to obtain the optimal conditions and the desired yield; thus, it has gained great interest to be widely employed in optimizing plant natural products extraction processes [35][36][37][38]. In this study, a simple, effective, and nodust pollution homogenate-combined ultrasonic cavitation synergistic extraction (HUCSE) method was proposed for the extraction of flavonoids from C. camphora leaves. An RSM-based Box-Behnken design (BBD) was applied to offer the optimal combination of ethanol concentration, homogenate/ultrasonic time, solvent-to-solid ratio, and ultrasonic power with which a maximum yield of C. camphora flavonoids can be attained by HUCSE and their antioxidant capability can be evaluated in vitro.

Apparatuses.
e HUCSE apparatus was employed for C. camphora flavonoids extraction as described in our previous study [25], which is a self-assembling equipment comprising a Philips disintegrator (Guangdong, China) and a Biosafer250up handheld Sonifier cell disrupter (SaferCo. Ltd, China). e highest shearing speed and volume of the disintegrator are 10,000 r/min and 250 mL, respectively. e Sonifier cell disrupter power can be regulated freely with a range of 0-250 W.
e quantification of C. camphora flavonoids was conducted using the aluminum chloride colorimetric determination method according to Wang et al. [39] with slight modifications. 1 mL diluted rutin standard solution (prepared using 60% ethanol aqueous solution) or sample solutions were transferred into 10 mL volumetric flasks and 1 mL of AlCl 3 solution (5%) and 2 mL of CH3COONa solution (1 mol/L) were added, followed by adjustment to the scale with 60% ethanol aqueous solution.
e mixtures were placed for 20 min in atmospheric temperature and then detected at 400 nm against the mixture without coloration as a reference by a UV-Vis spectrophotometer (751-GW, Shanghai, China). e yields of the flavonoids were conveyed as milligram of rutin equivalents per gram of dry weight of C. camphora leaves based on the standard calibration curve. e calibration curve (y � 2.40x − 0.0645, where y is absorbance at 400 nm, x is the concentration value) ranged from 0 to 0.05 mg/ml (R 2 � 0.9963). All experiments were conducted three times, and the results were conveyed as mean ± SD.

HUCSE Process.
Dried C. camphora leaves were weighed and transferred into the HUCSE system accompanied with the addition of a definite volume of ethanol solution followed by treatment under the presetting conditions for flavonoids extraction. After each treatment, the suspension was centrifuged at 8,000 × g for 20 min to collect the crude extract solutions and then stored in a refrigerator prior to the analysis of flavonoids content by UV-Vis spectrophotometry. Each experiment trial was performed in triplicate for accuracy.

Experimental
Design. BBD, a member of RSM, is characterized with a spherical and revolving design. It comprises a central point, and the intermediate points circumscribed on the sphere at the cube edges [40]. Herein, a three levels of four parameters of BBD with a total of 29 experiment trails (24 factorial points and 5 replicates of the central points) was employed to investigate the independent and interactive influences of the four factors on the extraction yield of flavonoids, and the factors are ethanol concentration (A, %), homogenate/ultrasonic time (B, min), solvent-to-solid ratio (C, mL/g), and ultrasonic power (D, W). e scope and level of each factor as shown in Table 1 are gained based on the single factor experiments. All the experiment trials generated from Design-Expert software were performed in triplicate in randomized order, and the average value from three replicates of each experiment trial was recorded as the response value.
e Design-Expert (Version 8.0, Minneapolis, USA) software was employed for performing the model establishment, experimental design, analysis of data, and graph plotting. A quadratic equation was fitted to investigate the correlation between the determined values and the four independent variables as follows: where β 0 is presented as the constant; β i , β ii , and β ij are defined as the coefficients of linear, quadratic, and crossproduct, respectively. X i and X j are given as the independent factors at different levels.

Conventional Extraction
Method. e conventional heat reflux method (HRE) was performed as the reference method to make a comparison with the proposed HUCSE [41]. HRE was carried out three times under a fixed operation power of 1 kW for 4 hours using an electric jacket. 10 g of dried C. camphora leaves powders (60 meshes of particle size) was weighted and placed into a glass flask, and then a definite volume of ethanol aqueous solution was added before subjecting to extraction by HRE. e other extraction conditions applied in HRE were the optimal conditions based on the results of the optimizing process for HUCSE. After the extraction, the mixture was transferred to certification and then analyzed by UV-Vis spectrophotometry as mentioned above.

Kinetic Model.
e second-order kinetic model offers an adequate 1 acceptable illustration with respect to the solidliquid extraction procedures [42] and has been used prominently in modeling extraction [43,44]. It generally divides the whole extraction process into two coinstantaneous stages: (1) at the beginning the extraction yield rises rapidly over time, and (2) the extraction yield decreases slowly with the increase in time till to the end of extraction [45]. e extraction kinetics for flavonoids from C. camphora leaves by HUCSE and HRE were investigated on the basis of the second-order kinetic model. e model parameters h, k, Y s , and Y t are defined as the original extraction rate (mg/g·min), second-order extraction rate constant (mg/g·mim), extraction capacity (mg/g) at saturation, and the extract yield (mg/ g) at any moment t (min), respectively. e dissolution rate of flavonoids contained in the solid transferring to solvent can be represented as Considering the boundary conditions from t � 0 to t and the corresponding Y t � 0 to Y t , the second-order model equation (1) can be integrated and rearranged into equation (2) as follows: Table 1: Box-Behnken design matrix and the actual and predicted values for the yields of C. camphora flavonoids.

Run
When equation (3) is linearized, it can be expressed as On arranging equation (3), the extraction rate can be calculated using equation (4): e initial extraction rate (h) can be denoted by equation On arranging equation (4), we get the following equation: e three second-order kinetic model parameters (h, k, and Y s ) can be calculated experimentally by the intercept and slope of the t/Y t versus t plot.

Antioxidant Activity Assays
2.8.1. DPPH Radical-Scavenging Assay. DPPH-scavenging test was performed to investigate the free radical-scavenging ability of C. camphora flavonoids based on Yang et al. [46]. A series of diluted sample solutions were blended with 3.9 mL 25 mg/mL of DPPH ethanol solution and then placed in dark for half an hour at ambient temperature. e mixed solution absorbance was detected at 517 nm. V C , BHT, and BHA were employed to replace the sample solution as positive control groups to make a comparison of C. camphora flavonoids. DPPH-scavenging capacity can be determined with the following equation: where A 0 and A 1 are denoted as the absorbance of the negative control group without sample solution and the tested groups, respectively.

Ferric-Reducing Antioxidant Power (FRAP).
According to the study of Benzie and Strain [47], the antioxidants in attendance can result in reducing of Fe 3+ -TPTZ into Fe 2+ -TPTZ. FRAP solution was comprised of 25 mL 300 mM of acetate buffer solution, 2.5 mL 10 mM of TPTZ, and 2.5 mL 20 mM of FeCl 3 solution and then subjected to incubation for 30 min around 37°C. e reaction was initiated through mixing 2.85 mL of FRAP solution with 0.15 mL of diluted sample solution and then placed the mixture in darkness for 30 min. After reaction, the absorbance of the mixture was detected at 593 nm using a spectrophotometer. Positive control groups were carried out as above steps by replacing sample solution by V C , BHT, and BHA. e ferric-reducing power of flavonoids was conveyed as μM trolox equivalents (TE)/g extracts.

Determination of Reducing
Power. e assay for the evaluation of reducing power was performed based on Oyaizu's study [48]. 1 mL of sample liquid, 2.5 mL 0.2 M of phosphate buffer (pH 6.6), and 2.5 mL 1% of K 3 Fe(CN) 6 solution were mixed and incubated at 50°C for 20 min and then 2.5 mL 10% of trichloroacetic acid was added, followed by centrifugation at 10,000 × g for 10 min. Aliquots of 2.5 mL of the upper layer were collected and then blended with 2.5 mL of deionized water and 0.5 mL 0.1% of FeCl 3 and then were detected at 707 nm. Positive control groups were carried out as mentioned above by replacing sample solution by V C , BHT, and BHA.

Influence of Ethanol Concentrations.
Ethanol is a generally used extractant owing to its remarkable penetration capacity into the plant materials, relatively low boiling temperature (easily recycled) and cost, safety, and nontoxicity [49]. e proportion of ethanol is an important parameter as the extraction yields are largely dependent on the solubility of flavonoids in ethanol solution. Higher proportion of ethanol could result in the dissolution of some liposoluble constituents, but lower proportion of ethanol may bring in incomplete extraction. C. camphora leaves (1 g dry weight) were extracted by HUCSE at an ultrasonic power of 250 W for 20 min with various proportions of ethanol (0-100%), and the solvent-to-solid ratio was 20 mL/g. As shown in Figure 1(a), in the rise of ethanol concentration (from 0 to 75%), the extraction yield of C. camphora flavonoids showed an increasing tendency. However, an upward trend was observed in the extraction yield when the ethanol concentration was over 75%. So, 75-100% of ethanol concentration was applied for the following experiments as an apparent change of extraction yield was observed in this range.

Influence of Homogenate/Ultrasonic Time.
To obtain the appropriate homogenate/ultrasonic time, a series of experiments were conducted at different HUCSE times, and the results are presented in Figure 1(b). e extraction yield was very low at the first 10 min of HUCSE process, which indicated that the synergistic effect of homogenate and ultrasonic cavitation energy needs time to break down the structures of plant cell walls and thus promoting the target analytes released from plant materials into the solvent. It indicated the extraction yield of flavonoids enhanced dramatically with homogenate/ultrasonic time increasing from 10 to 20 min, while long homogenate/ultrasonic time did not result in apparent improvement, and thus 20 min was selected as the middle level. erefore, a range of 15-25 min homogenate/ ultrasonic time was determined for the latter experiments.

Influence of Solvent-to-Solid Ratio.
e solvent-tosolid ratio is a crucial factor in the extraction procedure, excessive volumes of the solvent could give rise to the tedious extraction process and needless waste, and minute volumes of solvent may result in the incomplete separation. Hence, different solvent-to-solid ratios from 12 to 28 mL/g with 4 mL/g intervals were studied to analyze their effects. As presented in Figure 1(c), the extraction yield of flavonoids enhanced apparently in the rise of solvent-to-solid ratio from 12 to 20 mL/g, and this is due to the higher solvent-tosolid ratio; the sample could contact solvent more sufficiently, and hence, the extraction yield were improved. With solvent to solids in the excess of 20 mL/g, high volumes of solvent did not trigger in the obvious improvement of the extraction yields. Hence, 20 mL/g was selected as the middle level, and 16-24 mL/g was selected as the suitable range of solvent-to-solid ratio for the further experiments.

Influence of Ultrasonic Power.
To analyze the effect of ultrasonic power on the extraction yield of flavonoids, tests were conducted at different ultrasonic powers (50,100,150,200, and 250 W) with 75% of ethanol concentration, 20 min of homogenate/ultrasonic time, and 20 mL/g of solvent-tosolid ratio, respectively. As shown in Figure 1(d), when ultrasonic irradiation power raised from 50 to 150 W, the extraction yield enhanced dramatically; this phenomenon was perhaps because the synergistic influence of the homogenate and ultrasonic cavitation triggered the processes of solvent permeating into the interior plant materials and the target compounds diffusing into solvent occurring more rapidly. Further increase of ultrasonic power just brought a slow improvement in extraction yields; an ultrasonic power around 200 W was sufficient for flavonoids extraction and therefore was chosen as the middle level. Hence, 150-250 W was identified as the suitable range of ultrasonic power. Journal of Analytical Methods in Chemistry 5

Experimental Design and
to determine optimal extraction conditions. e extraction yield was defined as the response. e design matrix, numbered, and actual forms at three levels (denoted by +1, 0, and -l) of four independent factors; the determined extraction yields by HUCSE process; and the predicted values generated from BBD are given in Table 1. Ethanol concentration (A), homogenate/ultrasonic time (B), solvent-tosolid ratio (C), and ultrasonic power (D) were studied as shown in Table 1. e quality of the developed model was further investigated using ANOVA analysis ( Table 2).

RSM Model.
e model suitability was verified by the coefficient of determination (R 2 � 0.9903), the adjusted coefficient of determination (adjusted R 2 � 0.9754), and the coefficient of variation (C.V � 1.26%), which revealed that more than 99% of the obtained actual values can be interpreted by the selected model, and the model accuracy and generic availability are capable. e predicted R 2 of 0.9516 was corresponded well with the adjusted R 2 . e adequacy precision estimated the signal-to-noise ratio, and a ratio higher than 4 is generally desirable. e adequacy precision of 38.78 revealed that the developed model could be employed to handle the design space. e significance of all the coefficients was examined by F-test coupled with the P-value (Table 2). e developed regression model for the optimization of HUCSE was extremely significant as evidenced by the F-value (101.79) and a very low P-value (<0.0001) as shown in Table 2. e value of "lack of fit" (0.3111) was insignificant for the developed model, which further affirmed its correctness.

Effect of Process Variables on Extraction Yield.
Statistical analysis regarding the regression model for the extraction of C. camphora flavonoids suggested that the interactive influences of HUCSE process was extremely significant affected by the ethanol concentration, homogenate/ ultrasonic time, and solvent-to-solid ratio and ultrasonic power, in both linear and quadratic manners. e interaction of solvent-to-solid ratio versus ultrasonic power, homogenate/ ultrasonic time versus ultrasonic power, and ethanol concentration versus solvent-to-solid ratio or ultrasonic power showed extremely significant, highly significant, and significant influences on the extraction process, respectively. Nevertheless, the interaction effects between homogenate/ ultrasonic time to ethanol concentration and solvent-tosolid ratio were statistically insignificant. By using multiple regression analysis on the determined values, the empirical relationship between the extraction yield and four factors in natural values was represented using a polynomial equation:

Optimization of the HUCSE Procedure.
e regression polynomial equation can be delineated by both the threedimensional response surface and the two-dimensional contour graphs generated from BBD. ese graphs offered a way to visualize the connection between response values and detailed experimental levels of four factors and the interactive effects between two test factors on the extraction yield in HUCSE process. e contour plot shapes can reflect the statistical significance of mutual interactions between the factors, with which a circular contour graph indicates that the interactive effect between the factors are insignificant, while an elliptical contour graph suggests that the interactive effect between the factors are significant [50]. e connection between independent and dependent factors was depicted in three-dimensional response surface and two-dimensional contour graphs provided by the developed model for extraction yield; two independent factors were plotted in a three-dimensional surface graph, while the other two factors were maintained at level zero. e threedimensional response surface and contour graphs illustrating a significant interactive effect of the two factors are presented in Figure 2. Figure 2(a) shows the reciprocal interaction of ethanol concentration and solvent-to-solid ratio on the yield of flavonoids when homogenate/ultrasonic time and ultrasonic power were fixed at 20 min and 200 W, respectively. It was observed that ethanol concentration demonstrated a quadratic influence, while the solvent-to-solid ratio showed a linear influence on the extraction yield. e extraction yield originally improved with an increase in these two factors and then declined with an increase in ethanol concentration. Figure 2(b) shows that the reciprocal interaction of ethanol concentration and solvent-to-solid ratio on HUCSE process. Ethanol concentration revealed a quadratic effect, while the solvent-to-solid ratio showed a linear influence on extraction yield. Figure 2(c) shows the reciprocal interaction of homogenate/ultrasonic time and ultrasonic power on HUCSE process when ethanol concentration and solvent-tosolid ratio were fixed at 75% and 20 mL/g, respectively. e variations of extraction yield were highly significant with an increase in both homogenate/ultrasonic time and ultrasonic power. Likewise, Figure 2(d) shows the interactive effect of solvent-to-solid ratio and ultrasonic power on the extraction yield when ethanol concentration and homogenate/ ultrasonic time were fixed at 75% and 20 min, respectively. e reciprocal interaction between solvent-tosolid ratio and ultrasonic power were extremely significant and showed a linear effect on the extraction yield.

Optimization of HUCSE and Verification.
As for the BBD optimization process, which needs less experiment trials to be performed for a three-level factorial than other experiment designs to illustrate the significant factors, the possible interactive effects between the variables studied on the extraction yield of target compounds to attain the optimal operation conditions and the satisfied response [51]. By superimposing or overlaying critical response contours on a contour plot, the best compromise can be visually searched. Meanwhile, the function of point prediction allows entering levels for each factor or component into the current model. e software calculates the expected responses and associated interval estimates based on the prediction equation that is shown in the ANOVA output. e optimum HUCSE conditions with a theoretical extraction yield of 8.09 mg/g (ethanol concentration 76%, homogenate/ ultrasonic time 25 min, solvent-to-solid ratio 22 mL/g, and ultrasonic power 243 W) for the flavonoids extraction were predicted by BBD of the RSM optimization approach. e abovementioned conditions with slight modifications (ultrasonic power 240 W) were applied to verify experimentally and attain the real extraction yield of flavonoids by HUCSE process.
e average extraction yield of flavonoids was 7.95 ± 0.27 mg/g (n � 3), which was in good accordance with the predicted response by the model equation and further confirmed that the developed response model was capable for the HUCSE process optimization.

Comparison of Extraction Methods and Kinetic Study.
Extraction kinetic modeling was employed to make a comparison of the inherent behaviors of concern on heating and mass transfer during HUCSE and HRE procedures for C. camphora flavonoids extraction. e variations of flavonoids extraction yield with changing the treatment time in the procedures of HUCSE and HRE were depicted as presented in Figure 3. HUCSE process obviously saves the extraction time to reach the extraction equilibrium which just spends around one-tenth of the time of HRE. A desirable extraction yield of 7.95 ± 0.14 mg/g was acquired in 25 min by HUCSE, while 240 min of extraction time was consumed by HRE with a maximum extraction yield of 7.72 ± 0.22 mg/g. e parameters of Y s (extraction capacity at saturation) and k (second-order extraction rate constant) ( Table 3) were obtained by fitting the second-order kinetic model and plotting graphs (Figure 3) of t/Y t versus t to the actual experimental results. As shown in Table 3, particularly high R 2 (0.9995 for HUCSE and 0.9984 for HRE) denoted that the second-order kinetic mathematical model was adequate for fitting the HUCSE processes of flavonoids. e parameter Y s was applied to determine the extraction efficiency of HUCSE compared to that of HRE; it was observed that HUCSE (Y s � 14.95 mg/g) was more efficient for the extraction of flavonoids than traditional HRE (Y s � 13.05 mg/g). Meanwhile, the proposed HUCSE possessed apparently higher original extraction rate (h) and the second-order extraction rate constant (k) for flavonoids separation in comparison to HRE. ese results all declared that HUCSE is an efficient technique for the extraction of C. camphor flavonoids. It can be concluded that the synergistic effects of the homogenate and ultrasonic cavitation are the main reason that the proposed HUCSE method can dramatically shorten the extraction time and improve the extraction efficiency. A similar result was also observed in our previous study [25].

Antioxidant Activity.
Scavenging activity on DPPH-free radicals is an important indicator on the investigation of antioxidant activity of bioactive compounds [52]. Figure 4(a) reveals the DPPH-scavenging activity of extractant and the control sets with varying concentrations. It was observed a      dose dependence manner of C. camphor flavonoids on scavenging DPPH radicals. Compared to the positive control sets of V C , BHT, and BHA, C. camphor flavonoids revealed relatively low DPPH radical-savaging activity at low concentrations, notably with a further increase of concentration, flavonoids showed approximately similar DPPH radicalsavaging activity as Vc. FRAP test was performed in the present study to evaluate the antioxidant ability of C. camphor flavonoids. As presented in Figure 4(b), linear correlations between the concentrations of extracts or the commercial antioxidants and trolox were observed. Compared to BHA, flavonoids showed a slightly lower reducing ability, while it is adverse to these of VC and BHT and displayed much higher reducing ability at the same concentrations. As shown in Figure 4(c), reducing power assay showed that all four tested compounds exhibited a concentration-dependent tendency on the reducing power. Even if flavonoids enjoyed a little bit lower reducing power than that of VC, BHT, and BHA, the reducing power improved dramatically with the increase of concentration and was very close to that of the three commercial antioxidants. is tendency corresponded well with the results of DPPH radical-scavenging activity. In summary, it can be concluded that C. camphor flavonoids showed great potential as a natural antioxidant to substitute the traditional synthetic antioxidants based on the above results.

Conclusion
In this study, HUCSE technique was developed with the merit of no-dust pollution for the efficient extraction of C. camphora flavonoids. BBD was employed to optimize the HUCSE process; the optimal operation conditions were attained and validated, and the results showed that the improved HUCSE method is adequate for the extraction of flavonoids. e second-order kinetic model was performed to investigate the extraction kinetics of HUCSE and HRE of flavonoids, and the kinetic parameters were obtained and analyzed. HUCSE, compared with traditional HRE, enjoyed the higher efficiency for flavonoids extraction and could be extended to isolate other bioactive compounds from plant materials. Additionally, C. camphora flavonoids had remarkable antioxidant ability compared to the commercial antioxidants.

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest
e authors have no conflicts of interests to declare.