Feasibility Study of PV-Wind-Fuel Cell Hybrid Power System for Electrification of a Rural Village in Ethiopia

As the energy consumption is increasing in an alarming rate and peoples and international communities are well aware of environmental protection, alternative (i.e., renewable and fuel cell based) distributed generation (DG) systems have attracted increased interest. Wind-based and photovoltaic(PV-) based power generation are two of the most promising renewable energy technologies. Fuel cell (FC) systems also show great potential in DG applications due to their fast technological development and the merits they have, such as high efficiency, zero or low emissions (of pollutant gases), and flexible modular structure. In this work, the techno-economic feasibility study (using HOMER) of emission-free hybrid power system of solar, wind, and fuel cell power source unit for a given rural village in Ethiopia called Nifasso (latitude of 9°58′40′′N and longitude of 39°50′3′′E with an estimated population of 1059) that can meet the electricity demand in a sustainable manner has been studied.-e main power for the hybrid system comes from the solar and wind energy while the fuel cell and rechargeable batteries are used as a secondary and primary energy back up units, respectively. We can say storage as primary and secondary based on the sequence of operation. Hence, when there is shortage, first the battery discharges to fulfill the load demand and if the battery reaches to its allowable minimum capacity, it will stop further discharging and the fuel cell will operate so as to convert the stored hydrogen into electricity. In the result, different feasible alternative solutions have been obtained with a narrow range of COE which are better than the previously studied PV-wind-Genset hybrid set ups.


Introduction
Most people in the rural villages use kerosene for lamp, diesel for water pumping and flour mills, fire wood for cooking, and dry cells for radio and tape recorders.Desertification of the land is getting worse and worse due to deforestation and backward agricultural practices.Hence, the communities that live in the rural villages are suffering from lack of electricity.erefore, women are forced to do their day-to-day domestic activities such as cooking, using fuel wood which leads to a rapid growth of deforestation; they travel long distances to fetch water; and they also use kerosene lamp at night.Additionally, due to lack of access to electricity, the communities in the rural villages are not able to benefit from social services such as clinics and schools sufficiently.erefore, village electrification is a vital step for improving the socioeconomic conditions of rural areas and crucial for the country's overall development.e villages' welfare is one of the main aims of the rural electrification program.Enormous benefits can be achieved in irrigation, food preservation, crop processing, agriculture, and rural small-scale industries [1,2].It creates employment opportunities for the villages' youth and promotes a better standard of life.Hence, availability of electricity reduces poverty and helps economic development by enhancing the health, education, and water supply (for drinking and irrigation) needs of the rural population [3][4][5].
Keeping in mind the above facts, the authors of this work believes that designing and implementing cost-effective renewable energy-based hybrid systems to supply electric loads is a best candidate solution.
Most feasibility studies in Ethiopia which have been conducted till now on the hybrid systems are PV/wind/Genset and PV/wind/hydro types.Hence, this work tries to look the other possibilities by incorporating fuel cell systems as secondary back-up units.But, several authors have studied the wind/PV/fuel cell, PV/fuel cell, and wind/fuel cell hybrid systems for different case studies in the world.For instance, Debnath et al. in [6] describe a hybrid power generation system suitable for remote area for agricultural application.
e hybrid system is studied using HOMER software.e load has a peak value of 13 kW with a 2.2% day-to-day and hour-to-hour variation.To satisfy this load demand, a hybrid PV/FC/battery/electrolyzer system with 80 kW PV and 10 kW FC has been suggested with a COE of 0.431$/kWh [6].

Brief Note on HOMER
Hybrid Optimization Model for Electric Renewables (HO-MER) software helps to find the least cost combination of components that meet a required load, based on an hourly analysis of the input variables, such as wind and solar data.For systems that meet the yearly load, the life-cycle cost is also estimated by the software.HOMER can be applied to a number of system designs: grid-connected or off-grid, stand-alone or distributed generation, and conventional or renewable technologies.e renewable technologies can be classified into three groups as power sources, storage, and loads [7].
In the category of power sources, the most common types are the following: photovoltaic (PV); wind turbine; hydropower; generators with different prime movers such as diesel, biogas, or coal-fired; electric utility grid; and microturbine or fuel cell.In the storage class, bank of batteries and hydrogen can be mentioned.With regard to loads, there are two types: primary and deferrable loads.e primary load is the electrical load that must be met at a specified time (e.g., lighting), and the deferrable load is the load that need not be met within a specified time but should be met within a certain time period (e.g., water pumping) [7].
e software is sufficiently intelligent to identify the proper timings of energy supplied to the components which are connected to the system.For systems which include batteries and a generator, the software can decide the times at which the batteries should be charged and when the generator should be operated.It also gives the deferrable load a lower priority than the primary load but a higher priority than charging the batteries.For this, there are two dispatch strategies that HOMER follows.A dispatch strategy is a set of rules by which the operation of the generator and the batteries is controlled whenever there is a shortage of energy from the renewable resources.ere are two types of dispatch strategy: load following and cycle charging.e load following strategy enables HOMER to serve the deferrable load under two conditions.ese are (a) when the storage tank is empty and (b) when the system produces excess electricity.Under a cycle charging strategy, the generator serves the deferrable load when it is able to produce more electricity than that needed by the primary load.If the storage tank is empty, then the deferrable load is considered a primary load and all the power sources serve the deferrable load as much as possible [7].
e software also provides a feature for carrying out sensitivity analysis, which enables the evaluation of the economic and technical feasibility of several technological options. is feature can also be used when there is doubt over the exact value of a certain input, such as the annual average wind speed, annual average solar radiation, diesel price, or the price of PV cells.Furthermore, when the data represent a range of applications, this feature can be used.
e sensitivity analysis performs energy balance calculations on hourly basis for a whole year (8,760 hours).It compares the electric load for each hour to the energy that the system can supply during that hour.While carrying out the sensitivity analysis, the optimization process is repeated for each input value in the range so that the effect that changes in the value have on the results can be examined [7].
Nonetheless, this is not as simple as it may seem; as the number of sensitivity variables increases, the computational time of the software also increases, which could be considered a limitation or a challenge to using the software.When using the sensitivity analysis feature of the software, several sizes of each component must be considered in order to meet the load and the computation time is dependent on how many of them are used.To minimize the computation time, an iterative process needs to be followed.is is done by first considering just a small number of sizes and/or variables over a relatively large range to decrease the initial running time.After each successive run, a greater number of options and variables are added within the range in order to increase the resolution.Indeed, this takes quite a long time and can be considered as a limitation of the software [7].
Furthermore, similar to the several sensitivity variables that can be input into the sensitivity table, there is another search space table to which can be applied different sizes and quantities of the different system components, such as the size of PV array, generator, inverter, and the quantities of batteries and wind turbines.Again, this further lengthens the computation time of the software, as the software tries each and every component size and quantity.As in the previous case, the simulation can first be run coarsely, by minimizing the number of variables within the range.e results are then refined by adding a greater number of variables within the range.It should also be noted that the greater the number of variables within a certain range supplied to HOMER, the better the result.However, attention needs to be paid to the computation time [7].
After running the simulation, the results are given as a list of feasible system configurations, sorted by life-cycle cost.From the results, the least-cost systems, which are displayed in the first few rows of the list, can be chosen for implementation.e designer can also scan for other feasible systems in the list and decide to take any particular setup by evaluating the pros and cons of the setup against cost, renewable resource contribution, future price trend of the components, and so on.Following on from this, the technology options, component costs, and available resources were input to the software.HOMER used the inputs 2 Journal of Electrical and Computer Engineering to provide different feasible system configurations, which were sorted according to their net present cost [7].

Load Estimation
Deciding on the load is one of the most important steps in the design of a hybrid system [8][9][10].Primary load, which must be met immediately, and deferrable load, which must be met within a certain time, are both considered in this work.Electric load in the rural villages of Ethiopia can be assumed to be composed of lighting; radio and television, water pumps, health post, and primary schools load [7,11].e work indicated in [12] considered only lighting, radio, and television as community loads.Another study in Ethiopia [13] assumes additional electricity demand for cooking and for flour mills to the load together with the load considered in [7].In this paper, barbers, shops, and church loads are incorporated additionally.
e daily power demand and energy need for the community of 289 households are estimated by considering basic domestic appliances such as television (70 W), CFLs of 11 W and 15 W for lighting, radio/tape (5 W), VCD/DVD player (15 W), refrigerator (70 W), "electric mitad" (2.5 kW), cell phone (2.5 W), and stove (1.5 kW).e primary school consists of 8 classrooms, a director office, teacher's staff room, toilets, and a guard house.Each classroom is assumed to be installed with four 15 W CFLs (compact fluorescent lamps); one 15 W CFL is suggested for the teacher's staff room; one 15 W CFL is assumed for the director office; two 11 W CFLs are allowed for the toilet; one 11 W CFL for the guard house, and additional 4 CFLs (of 15 W) for external lighting are also considered.Evening classes are conducted from 18:00 to 21:00.Additionally, four computers (LCD desktop type of 200 W), one in the director office and three in the teacher's staff room; one printer (360 W); one photocopy machine (1000 W); tape/radio (5 W); one GSM wireless telephone (2 W); and two ceiling fan (80 W, each one in the director office and one in the teacher's staff room) are proposed.
For the health centers, having 3 rooms, 15 W CFL per room, one 15 W CFL for external lighting, one 11 W for the toilet, and one 11 W CFL for guard house are considered.When we come to the appliances used, it is based on the typical category I rural health clinic presented in [14].Accordingly, basic small health post clinical equipment's such as vaccine refrigerator (134 W), a 15 W capacity microscope, a 135 W capacity centrifuge, a 2 kW water heater, a 400 W incubator, a 75 W television, a GSM wireless telephone (2 W), and three ceiling fans (each of 80 W in each room) are suggested.
For the community, two flour milling machines of 12.5 kW capacity each working from 9:00 to 12:00 and 14:00 to 18:00 with four 15 W CFLs for internal lighting (from 18: 00 to 20:00) and two 15 W CFLs for external lighting (from 18:00 to 6:00) are assumed.
For the church, six 15 W CFLs in the internal lighting, one 15 W CFL in the "Bethlehem," one 15 W CFL in the office, four 11 W CFLs in the "meeting hall," four 15 W CFLs for the external lighting, and one 11 W for the guard house are assumed.Besides these, a GSM wireless telephone of 2 W is proposed.
ere are a total of three shops assumed, and each shop is expected to have a radio/tape of 5 W and 15 W CFL. e CFLs are supposed to operate from 18:00 to 21:00.
In the community, two barbers are considered each having two hair clipping machines of 12 W. Additionally, one 15 W CFL for lighting between 18:00 and 21:00 is suggested for each.
e total primary load in weekend is expected to be less than weekdays.Because, some loads such as milling machines, school loads, and clinics will not operate.Hence, by considering some load reduction in weekends, the 24-hour load trend curve indicated in Figure 1 was obtained.
Water pumping system is required for households, schools, and health care centers.A minimum of 100 liters of water per day per family and 2400 liters/day for each pair of one health center and one primary school is suggested [7,13].erefore, to accomplish this, we need to have three 1.528 kW of 40.416 l/m capacity (a total need of 4.584 kW) water pumps so as to pump water for the community which operates for four hours with the energy demand of 18.336 kWh.Again, we need to have one 1.119 kW of 20 l/m capacity water pump for the school and clinic that operates for two hours with the energy demand of 2.238 kWh.Hence, the total peak deferrable load is 5.703 kW, which needs 20.574 kWh energy.
A water storage capacity of 4 days is suggested requiring a storage capacity of 73.344 kWh for the community and 8.952 kWh for primary school and health centers.Hence, the total storage capacity is equal to 82.296 kWh.e storage capacities can be obtained by multiplying number of days with energy demand of each water pump [15,16].
Up to 30% deferrable load reduction can be expected in the rainy season [7,12,17].15% load decrease for June, January, and September while 30% for July and August are assumed [13,15].ere are no classes in July and August (annual break) and in January (semester break).With these assumptions, the monthly power consumption and energy demand of the water pumps are indicated in Figure 2.

HOMER Model of the Hybrid System
In this work, a hybrid system based on hydrogen technology is considered which needs a hydrogen producing unit (electrolyzer), a hydrogen storing unit (storage tanks), and a hydrogen utilizing unit (PEM fuel cell).However, the system is based on intermittent energy sources and is likely to experience large minutely, hourly, and daily fluctuations in energy input.us, it should be emphasized that the main purpose of the hydrogen storage system is to store energy over a long period of time (hour to hour and season to season).Other small short-term energy storage such as a battery must also be included to supply power during transient load conditions.Figure 3 shows the model and the hybrid setup in HOMER.

Resource Inputs.
e monthly average wind speed for the study area obtained from [18] and National Journal of Electrical and Computer Engineering Meteorological Service of Ethiopia were fed into HOMER.Figure 4 shows the average wind resource profile of each month at 10 m above the surface of the earth.
e probability density function of the wind speed synthesized by HOMER is also given in Figure 5. e software estimates a Weibull k � 1.87 and c � 3.39 m/s.
In a similar way, the solar energy potential for the study area was fed into HOMER, and this is shown in Figure 6.
is figure also shows the clearness index which HOMER generates for the analysis.e clearness index is the fraction of solar radiation transmitted through the atmosphere which strikes the surface of the earth, and hence, it is a measure of the clearness of the atmosphere.It is a dimensionless number between 0 and 1, defined as the surface radiation divided by the extraterrestrial radiation [7,16,19].
Many literatures reported that typical values for the monthly average clearness index range from 0.25 (a very cloudy month) to 0.75 (a very sunny month) [7,20].And this fact can be seen clearly in Figure 6.Note also that, in Figure 6, clearness index falls in between 0.4 and 0.8, which is the indication of the availability of a relatively strong solar potential in the study area.
e monthly temperature variation which is fed into the HOMER software is indicated in Figure 7. HOMER uses the ambient temperature to calculate the PV cell temperature and to consider temperature effect in the PV system.

Summary of Additional Inputs for Simulation.
e capital, replacement, and operational and maintenance cost of each component in the hybrid system are given in Table 1.
e table also contains the components' average operational life year and the size and/or quantities considered in the erefore, as the software searches the optimum system combination, it uses the input values summarized in the table.Besides this input values, sensitivity variables are also defined for PV and FC costs.

Optimization Results
. Figure 8 shows some optimization results (which are part of the numerous alternative solutions from rank 1 up to 26) that are the possible configurations able to feed the system total load.Despite the numerous alternatives with equal renewable fraction, the choice of optimal system type is restricted by the varying nature of initial capital, net present cost, excess electricity, and COE of each set up.Accordingly, the one which is marked in blue color (the fifth rank) in which fuel cell operates for 2,731 hours/year is the best optimum PV-wind-fuel cell hybrid system configuration.Because, from rank 1 up to rank 4, the system configurations are PV only and PV-fuel cell types with small changes in COE and NPC from the selected one.Moreover, in the fifth rank, due to the availability of all power sources (PV, wind, and fuel cell), the reliability of the hybrid system will also be improved with only small addition of cost.
A hybrid power system containing PV, wind, and fuel cell power sources marked in blue color in Figure 8 can be summarized by Table 2.
As it can be seen clearly in the fifth rank that is marked in blue in Figure 8, the capacity shortage is reported as 0.01 which is nearly zero.Furthermore, the system report shows that there is an excess electricity of 43,460 kWh/yr (18.9%). is excess electricity is not discouraging as it can be used to serve the load growth that might come in near future.Besides this, this excess electricity can be utilized as a compensation for the losses in the distribution network.
Figure 9 shows the detailed net present cost share by each component of the optimal hybrid set-up supported by a bar graph.Hence, the net present cost share of each component in decreasing order can be recognized as PV, battery, wind turbine, converter, electrolyzer, hydrogen tank, and fuel cell.
Figure 10 displays the monthly average electricity production by each power unit.Hence, as it can be seen clearly, most of the electricity production is being shared by the PV followed by the wind turbine.But, the power production share by the fuel cell, even though it is significant, is small as compared with the PV and wind turbine power unit outputs.
is is also presented in Table 3. e monthly average hydrogen production by the electrolyzer is given in Figure 11.Recall that an electrolyzer converts the excess electricity into hydrogen by the electrolysis of water.As the simulation result reports that the total hydrogen production and total hydrogen consumption were found to be 684 kg/yr and 670 kg/yr, respectively.Besides this, the hydrogen tank autonomy (expressed in hours) which is defined as the ratio of the energy capacity of the hydrogen tank to the electric load was reported as 32.

Sensitivity Analysis Result.
Figure 12 shows sensitivity of the optimal system type under the imposed price variation of sensitive components.e PV capital cost multiplier on the Y axis and FC capital cost multiplier on the X axis are considered as sensitivity variables.In the graph, the total net present costs (NPCs) of the most cost-effective systems are also displayed.

Conclusions
In short, this work addressed a techno-economic analysis of PV/wind/FC hybrid power system preceded by community load estimation and resource collection.

Journal of Electrical and Computer Engineering
Regarding the potential of the resources, it is observed that, the wind energy potential of the site is of class 1 type according to the US Department of Energy (DOE) wind mapping.Such wind energy potential, although it may not be sufficient for a large independent wind farm, is a viable preference if incorporated into other energy conversion systems such as PV and others [7].e data sources for solar energy also confirmed the availability of huge potential of solar energy at the site.
e result of techno-economic feasibility study shows that there are numerous alternative feasible hybrid set ups with 100% contribution by the renewable resources and narrow range of COE (0.310$/kWh to 0.328$/kWh).Accordingly, the community electric demand can be satisfied by a hybrid system power source containing 110 kW PV, one PGE 20/25 wind turbine, a 40 kW converter, 120 Surrette  S6CS25P batteries, a 5 kW fuel cell, a 25 kW electrolyzer, and a 15 kg hydrogen tank. is hybrid system needs $465,100 initial capital, $6,215 for operation and maintenance, and $544,550 total NPC over the 25 life-year horizon.With these economics, the COE of the selected hybrid system was found to be 0.313$/kWh.Neglecting other factors, in terms of COE, the result obtained in this study is comparable and even may be better than what previously studied PV-wind-Genset hybrid set up showed.For instance, in [7,13], the range of COEs reported are 0.322$/kWh to 0.518$/kWh and 0.302$/kWh to 0.392$/kWh, respectively.But, the renewable fraction in both researches is poor-being too less than unity.Moreover, due to Genset package, there is a considerably high level of emission to the atmosphere such as CO 2 , CO, unburned HC,   Hence, a hybrid PV-wind-fuel cell power system can be considered as a good choice in this regard.

Data Availability
e wind speed and solar radiation data used in this study were obtained from NASA website and National Meteorological Service of Ethiopia.e cost data for each hybrid system component can be found in IRENA (International Renewable Energy Agency) cost release report.ese data can also be obtained from the corresponding author upon request.

Figure 8 :
Figure 8: Some of the optimization results.

Figure 12 :
Figure12: Sensitivity of the optimal system type for PV and FC capital multiplier variations.

Table 2 :
System architecture and cost summary.

Table 1 :
Summary of additional inputs for HOMER simulation.

Table 3 :
Electric power production and consumption.
2 , NO X , and particulate matter (smoke, soot, and liquid droplets) emitted per unit fuel consumed by the generator.