Design of a Circularly Polarized Z-Slot Antenna with Isotropic Pattern for the UHF RFID Reader of WSN

In an antenna for a UHF RFID reader of wireless sensor networks (WSN), receiver sensitivity in sensing multitags from remote distances is an important performance index. This study designed a dual structured Z-slot antenna with optimized receiver sensitivity to enhance the sensitivity to a circularly polarized antenna with an isotropic pattern for a UHF RFID. Through analysis of performance in the designed antenna, the following was verified: return loss ( S 11 ) was about −62.21 dB at 925.25 MHz, antenna gain was 7.36 dBi, and Δ P r , isotropic gain deviation, was 1.3 dB. Impedance matching was about 50.069 Ω at 925.25 MHz and VSWR was from 1.001 to 1.028. Through this research it was discovered that this can be applied to the design of all RFID readers of WSN. Based on the above results, it is suggested that a circularly polarized Z-slot antenna which can enhance receiver sensitivity over a wide range can be widely applied to UHF RFID readers of WSN.


Introduction
RFID is an electronic tag and detection system that confirms information on things and detects surrounding conditions as one of the several tasks.A variety of radio frequencies and techniques are used in RFID systems [1,2].
There have been a variety of studies in using the HF band (13.56 MHz), the UHF band (860 ∼ 960 MHz), and the ISM band (2.4 GHz) as the standard RFID frequency bands for WSN [3].As HF band RFID communication uses magnetic coupling, the receiver area of the antenna is very narrow and as the ISM band RFID is sensitive to the surrounding environment, the performance and sensitivity of the RFID system varies [1,2].However, the UHF band is the most outstanding for recognition rates and distance, and many tags can be recognized quickly using the radiation of electric waves.Also, as the signal is very stable in the surrounding environment and the tags and tag chips for this frequency can be produced at low prices, it is known that this is the most appropriate frequency for the realization of RFID technology and sensor networks [4,5].
However, for a plane polarized antenna in the UHF band, errors may occur due to reflection and the interference of signals when multipath signals from the RFID tag are detected, and to recognize tags, the location of the tag has to be in line with the polarized plane [6,7].That is, for the plane polarized antenna, as electronic waves are radiated in a linearly polarized way, it is hard to recognize many tags simultaneously according to the locations of tags and the directionality of tag antennas and multipaths can be causes of disruptions [8].To minimize errors due to multipath signals and gain high recognition rates regardless of the directions tag antennas face, a circularly polarized antenna is used.For a circularly polarized antenna, when two right-angled signals with different status and the same amplitude are polarized, electromagnetic waves are radiated circularly [9,10].This is more effective for recognizing several tags regardless of the locations of the tags and the directions of the antenna.That is, for a directional pattern antenna, gain is high but recognition ranges of tags are low [11].For an isotropic pattern, antenna gain is low but the recognition range of tags is wide, so studies to enhance receiver sensitivity with isotropic antenna over a wide range have been carried out [12][13][14][15].This study designed an isotropic antenna with high receiver sensitivity and an isotropic pattern for UHF RFID.To design and manufacture circularly polarized isotropic antennas, the signals of readers were divided into two signals of the same magnitude and an incidence difference of 90 ∘ .Electricity was supplied to a strip line with a length of /2.The radiation board was connected to the feeding point of the strip line to enhance receiver sensitivity and the Z-slot was designed in a section of the radiation board to enhance receiver sensitivity so that passive tags could be recognized over a wide range.
This study is composed of the following: Section 1 describes the design of circularly polarized antennas with an isotropic pattern for UHF RFID readers of WSN, Section 2 describes the design, manufacture, and simulation of the antennas for readers, Section 3 measures the parameters of the antennas manufactured and their performance, and Section 4 concludes the antennas designed.

Design and Simulation of an Antenna for Readers
We have designed and manufactured a circularly polarized antenna and Z-slot antenna with isotropic pattern.The processes are as follows.
2.1.Design and Manufacture of the Proposed Antenna.The block diagram of circularly polarized antennas for UHF RFID readers of WSN with an isotropic pattern is presented in Figure 1.For compatibility with different RFID readers a microstrip line was designed as shown in Figure 2. The inductance value ( 1 ) was adapted and impedance matching was 50 Ω.
As seen in Figure 2, a hybrid coupler with insertion loss of 0.16 dB and a status difference of 90 ∘ was used to give a status difference of 90 ∘ from the original signal.To divide signals into two right-angled linear signals with the same amplitude, two strip lines with a length of /2 were designed.We called the shape the dual structured antenna.The circularly polarized antenna designed was characterized by left-turn circular polarization (LHCP).For the PCB, a 1 mm thick FR4 epoxy substrate with a relative permittivity of 4.8 was used.To receive the minute power reflected from tags, two strip line feeding points with a length of /2 and a Z-slot radiation plate with cross section of 13.4 cm×13.4cm were used for a double antenna.
To achieve an isotropic pattern, the diagonal length of the radiation plate was /4 (80 mm), and length of each line () was 30 mm and the slot home span () was 6 mm as seen in Figure 3.

Simulated Results for Radiation Pattern Characteristics.
We used the ADS (advanced design system) 2004A of Agilent company for simulating the manufactured antenna.The simulation direction of the designed circular polarization antenna is as shown in Figure 4.The simulation result presented that it had high power density at 0360 ∘ direction to -, -, and -axis (isotropic pattern) as shown in Figure 5.

Parameter Measurement of the Designed Antenna and Performance Analysis
We measure and analyze the performance of the designed antenna as shown in the following.

Measurement of Return Loss (𝑆 11
).If there are unmatched impedance points in the transmission system, power reflection occurs there and part of the input power is reflected.
Here, the ratio of the input power to reflected power is the return loss.Measurement results for the return loss ( 11 ) of the designed UHF RFID reader of WSN are presented in Figure 6 and as shown in Table 1, the return loss decreased at 925.25 MHz to −62.21 dB.
The wideband of the return loss of −10 dB was between 720.25 MHz and 1.12 GHz and the wideband of the axis rate of 3 dB was within 1.2 dB.

Measurement of the Impedance Matching Parameter.
As a result of measuring the matching parameters of the designed antenna, matching was carried out with 50.069Ω at 925.25 MHz as shown in Figure 7 and VSWR was from 1.001 to 1.028.It was discovered that this is compatible with different RFID readers of WSN.The impedance of the designed antenna is presented in Table 2.    in Figure 8, and a horn antenna was used as a standard for comparison.The two antennas had a separation distance of 2.36 m.For the standard, a BBHA-9120-D made by SCHWARZBECK was used and the parameters are as presented in Table 3.The equation defined by H. T. Friis which describes this wave behavior in "free space, " called the Friis Transmission Equation, is [16][17][18] as follows: where   represents received power level,   represents transmit power level,  represents transmit wave length,   represents gain of the transmit antenna,   represents gain of the receive antenna, and  represents separation distance between antennas.It is convenient to express Friis formula in terms of  2 21 =   /  and dB: where the path loss is defined as ) . (

Measurements of Antenna Radiation Pattern and the
Gain Parameter.To measure the radiation pattern and antenna gain according to the directions of the designed antenna, the standard antenna and the designed antenna were rotated horizontally and vertically and the pattern and gain were measured in the four different aspects.Figure 9 presents the results of the test where the standard antenna was set horizontally and the designed antenna was set in front.The antenna gain was 5.28 dBi and Δ  , a deviation of isotropic gain, was 3.2 dB.
Figure 10 presents the results of the test where the standard antenna was set vertically and the designed antenna was set in front.The antenna gain was 5.83 dBi and Δ  , the deviation in isotropic gain, was 7.2 dB.
Figure 11 presents the results of the test where the standard antenna was set horizontally and the designed antenna was turned at 90 ∘ .The antenna gain was 7.36 dBi and Δ  , a deviation of isotropic gain, was 1.3 dB.
Figure 12 presents the results of the test where the standard antenna was set vertically and the designed antenna was turned to 90 ∘ .The antenna gain was 7.46 dBi and Δ  , a deviation of isotropic gain, was 16.4 dB.
Table 4 presents the results of comparing the antenna gains measured and the deviations of the isotropic gains under the four different test environments.The gain of the antenna manufactured through a Z-slot formed on the radiation plate was about 7.36 dBi.The largest gain is a little low, but the deviation in isotropic gain was 1.3 dB, which indicates that the radiation pattern is superior.the length of the side line (), and the slot span (), varied as seen in Table 5. Figure 13 is the designed antenna radiation plate.
Figure 14 shows the results of the test where the standard antenna with an unsatisfactory radiation pattern was set vertically and the designed antenna was set in front to measure the radiated power according to the Z-slot parameters.Figure 15 shows the results of the test where the standard antenna was set vertically and the designed antenna was turned to 90 ∘ .As a result of measuring the radiated power according to the Z-slot parameters, the larger the slot span was, the bigger the radiation gain was.When the slot span was larger than 6 mm resonance point, Δ  was higher.This indicates that the radiation pattern is not satisfactory.As a result of the measurements, when the diagonal length was /4, , the line length, was 3/32 (30 mm), and , the slot span, was 6 mm, the isotropic pattern was the most satisfactory.

Analysis of the Radiation Pattern according to the Radiation Plate.
To analyze radiation patterns according to the presence of the Z-slot on the radiation plate, the radiation pattern was measured with the standard antenna set vertically and the designed antenna turned 90 ∘ .As a result, it was discovered that the maximum antenna gain without a Z-slot was about 9.09 dBi and Δ  was about 24 dB.In the case when there is a Z-slot on the plate, the maximum antenna gain was about 7.36 dBi and Δ  was about 1.3 dB.Therefore, the maximum antenna gain was about 1.73 dBi and Δ  , a deviation of isotropic gain, was about 22 dB.Therefore, it was discovered that the isotropic pattern was superior when the Z-slot was designed on the radiation plate and the receiver sensitivity of passive tags in the wide range of the antenna for the RFID reader of WSN was superior (Figure 16).6 shows the electric characteristics of the designed antenna with the RFID antenna.The known antenna was more than 21 cm 2 in size while the designed antenna is only about 13.4 cm 2 .However, the antenna gain was the same as that of the known antenna, 5.28 ∼ 7.36 dBi, although its size is smaller.The VSWR of the designed antenna was 1.028, higher than that of the known antenna.The tag recognition distance of the known antenna was about 3 m in a narrow range while that of the designed antenna was about 3 m in a wider range.

Conclusion
This study designed a dual structured and circularly polarized Z-slot antenna for UHF RFID readers of WSN with an isotropic pattern.
To recognize many tags at a remote distance at the same time without errors, the designed antenna had an insertion loss of 0.16 dB and used a hybrid coupler with a status difference of 90 ∘ so there was a status difference of 90 ∘ from the original signal.Also, to separate signals into two rightangled linear signals of the same amplitude, there were two strip lines with a length of /2.The designed dual antenna had a left-turn circularly polarized pattern and to receive the minute amount of power returned from the tags, it was designed to have strip line feeding points of length of /2 and a Z-slot radiation plate with a cross section of 13.4 cm × 13.4 cm.As a result of the test of the designed antenna, the return loss was about −62.213 dB at 925.5 MHz and the antenna gain was 7.36 dBi.Impedance matching was 50.069Ω at 925.25 MHz and the VSWR was from 1.001 to 1.028, which indicates that it can be used for different RFID readers of WSN.
The designed antenna was half the size of the known antenna, but it had an isotropic radiation pattern as good as and with the same electrical characteristics as the known one and recognized passive tags over a wide range.Such a dual structured and circularly polarized Z-slot antenna with an isotropic pattern can contribute to enhanced receiver sensitivity through maximizing antenna efficiency and to the development of antennas for UHF RFID readers of WSN with respect to compatibility with other systems.

2 InternationalFigure 1 :
Figure 1: Composition of antennas for the UHF RFID reader of WSN designed.

Figure 9 :
Figure 9: Radiation pattern for the antenna gain 1 (the standard antenna: horizontal and the designed antenna: frontal).

Figure 10 :
Figure 10: Radiation pattern for the antenna gain 2 (the standard antenna: vertical and the designed antenna: frontal).

Figure 11 :
Figure 11: Radiation pattern for the antenna gain 3 (the standard antenna: horizontal and the designed antenna: turned 90 ∘ ).

Figure 12 :
Figure 12: Radiation pattern for the antenna gain 4 (the standard antenna: vertical and the designed antenna: turned 90 ∘ ).

Table 1 :
Return loss ( 11 ) of the designed antenna.
3.3.Test Environment and Radiation Pattern Measurements3.3.1.Test Environment for Antenna Radiation Pattern.The designed antenna radiation pattern was measured by an absorber system.To measure performance, the circularly polarized Z-slot antenna was placed as a target, as seen

Table 3 :
Parameters of the standard antenna.

Table 4 :
Measured antenna gains and the deviations of the isotropic gains under the four different test environments.
3.3.3.Radiation Pattern Comparison according to the Z-SlotPlate Parameters.The design parameters of the Z-slot formed on the antenna radiation plate, that is, the diagonal length (),

Table 5 :
Design parameters of the Z-slot radiation plate.