The Impact of Wheel Flat on Traction Drive System of Electric Locomotives

,


Introduction
The dynamic interaction between vehicles and tracks has intensified with the increase in train operating speeds and axle loads.As a result, the service environment for the wheels has deteriorated, leading to more severe wear and damage between the wheels and the track [1][2][3].Currently, wheel flat is one form of wheel wear in railway vehicles.Wheel flats refer to the damage caused by wheel sliding during conditions such as startup and braking when the wheels lock or experience low adhesion [4,5], as shown in Figure 1.Wheel flats can lead to significant impact loads and seriously reduce the service life of the wheels [5].In extreme cases, wheel flats can even cause derailment, posing a significant threat to the safety of railway vehicle operations.Hence, an accurate analysis of the impact of wheel flat on wheel-rail contact parameters and the drive system is urgently needed.In addition, accurate detection of wheel flat scars is also crucial.The automatic damage identification algorithm proposed by Mosleh et al. [6,7] can be used to detect wheel tread damage.
Domestic and international scholars have conducted extensive research on the wheel-rail impact issue caused by wheel flats through experimental research, theoretical research, and numerical simulation.Existing research mainly focuses on the influence of wheel flat scars on wheel-rail impact force, vehiclerail system dynamics, and transmission system vibration.
1.1.Wheel-Rail Impact Force.Wheel flat can directly cause a large vertical relative displacement between the wheel and the rail, resulting in a considerable impact.In [8], a simplified formula for calculating impact force was introduced based on the formula relating low joint impact force and flat impact velocity.Uzzal et al. [9,10] researched the characteristics of wheel-rail impact forces caused by individual wheel flats and multiple wheel flats and analyzed the impact of train speed, flat length, and vehicle suspension parameters on the wheel-rail forces.In [11], a non-Hertzian foundational theoretical model was established considering the actual dimensions of wheel flats, and the vibration impact caused by wheel flats was analyzed.Similarly, Baeza et al. [12] studied the wheel-rail impact force caused by wheel flats, considering both new and worn wheel flats using a non-Hertzian contact theory.The research findings indicate that within the 20-200 km/hr speed range, the maximum wheel-rail impact force caused by new wheel flats increases with increasing train speed.However, the rate of increase gradually diminishes.It is worth noting that in [13], a fullscale high-speed wheel-rail interface test rig was used to test the wheel-rail dynamic impact caused by the wheel flat, and the same conclusion was obtained.In [14], wheel flats were input into the wheel-rail system as uneven displacements at the wheel-rail interface, and the impact and vibration characteristics caused by wheel flats were studied.
1.2.Vehicle-Track System Dynamics.The severe impact between the wheel and rail caused by the wheel flat can be transmitted to the entire vehicle-track coupling dynamic system.Lin et al. [15] established a rigid-flexible coupled model of high-speed trains and a finite element model for flat damage contact.The impact of single-or double-wheel flats with different positional distributions on the wheel-rail dynamics was analyzed [15].In [16], the dynamic characteristics of the wheel-rail interaction under the influence of new and worn wheel flats in heavy freight trains were studied based on the vehicle-track coupled dynamics theory, and suggestions for the maximum allowable limits of the two types of wheel flats were proposed.Han et al. [17] conducted numerical simulations using a finite element explicit algorithm and considered the strain rate-related parameters of wheel-rail materials to investigate the wheel-rail impact response caused by wheel flats in high-speed trains.In [18,19], a 3D wheel flat model considering length, width, and depth was established, and the influence of wheel flat on the dynamic response of the vehicle-track system was analyzed.Wang et al. [20] found that wheel flats caused a significant increase in contact force, contact stress, frictional force, and vibration acceleration between the brake interfaces.Additionally, Ye et al.'s [21] research showed that wheel flats can cause or exacerbate wheel polygonal wear, and the vehicle operating speed and the length of the flats significantly impact wheel polygonal wear.
1.3.Vibration of the Traction Drive System.Yang et al. [22] developed a wheel-rail dynamics model equipped with a gear system and analyzed the time-domain and frequency-domain effects of wheel flats on the gear system under variable speed conditions.The study conducted by Wang et al. [23] found that wheel flats can cause high-frequency vibrations in longitudinal creep forces and gear mesh forces.Similarly, a vehicle-track dynamics model considering the dynamic coupling of the gear system was established, and the effects of wheel flats on wheel-rail forces and gear mesh forces were analyzed [24].The vibration impact of wheel flats on motor bearings was analyzed by combining the Miner linear damage theory and vehicletrack coupled dynamics [25].The results showed that the periodic impact forces and high contact forces caused by wheel flats would reduce the fatigue life of the motor.The study in [26] demonstrated that wheels with flats exhibit more pronounced dynamic characteristics under traction and braking conditions, while the characteristic changes under sliding conditions are not significant.
In summary, there have been many studies on wheel flat, as shown in Table 1.However, these studies have mainly focused on the mechanical aspects of the traction drive system.A complete traction drive system consists of rectifiers, inverters, motors, gearboxes, and wheelsets.The traction drive system is a complex electromechanical coupling model where the vibration impact caused by wheel flats can be propagated to the electrical components of the drive system.Additionally, the fluctuating torque output by the traction motor can exacerbate the dynamic response fluctuations of the wheel-rail system [3].Therefore, relying solely on mechanical vibrations is insufficient to accurately calculate the dynamic response of the wheel-rail system and the traction drive system.In order to address this issue, this study

IET Electrical Systems in Transportation
employs an electromechanical coupling model to analyze the impact of wheel flats on both the electrical and mechanical aspects of the traction drive system.
The main contributions of this study are as follows: Considering the electromechanical coupling effect of the traction transmission system, a comprehensive analysis is conducted on the vibration impact of flat length, flat depth, and operating speed on the local dynamic response of the wheel-rail system.In addition, the influence of wheel flat scars on the electrical side rotor speed and motor torque fluctuations is also investigated.

Wheel Flat Impact Theory
In this section, it is assumed that the rail is rigid.In the case of an ideal wheel, the distance between the wheel center and the wheel-rail contact point is equal to the wheel radius.When analyzing the motion of a wheel with flats, it can be divided into low-speed and high-speed conditions [4].
In the low-speed scenario, depicted in Figure 2, the wheel undergoes a specific behavior as it rolls to point "a."It rotates around point "a" until the entire flat surface of the wheel aligns with the rail surface.At this juncture, the drop in the wheel center matches the depth of the flat spot, and point "b" of the wheel exerts a notable impact on the rail.Following this, the wheel rotates around point "b," ultimately restoring its normal rolling state.
In the high-speed scenario, as shown in Figure 3, after the wheel rolls to point "a," wheel-rail separation occurs.At this juncture, the normal force between the wheel and rail becomes zero.The wheel center undergoes a parabolic motion with a horizontal initial velocity of v under the effect of the wheel's self-weight and axle load.Eventually, the wheel's point "b" imparts a greater impact on the rail.
From the above analysis, it can be concluded that the impact characteristics of the wheel flat will inevitably change at a certain critical impact speed.The time for the wheel to rotate around point "a" by an angle α=2 is denoted as t 1 .The height corresponding to the wheel flat length is h.The time for the wheel center to drop h is denoted as t 2 .Assuming that the critical speed is v 0 , which should satisfy t 1 ¼ t 2 .t 1 and t 2 can be calculated respectively as follows [4]: where ω is the wheel rolling angular velocity, a 0 is the wheel drop acceleration in vertical direction.According Newton's second law, a 0 can be presented as follows: where F pszL is the vertical force of primary spring on the left side of the wheelset; F pszR is the vertical force of primary spring on the right side of the wheelset; m 2 denotes the primary unsprung mass of the wheelset; g is the acceleration due to gravity.According to the theory of multibody dynamics for locomotives, the vertical force exerted by primary springs can be expressed as the sum of the gravitational force corresponding to the primary unsprung mass and the prestress of primary sprung, which can be written as follows: where F spz is the superposition of F spzL and F spzR ; m 1 denotes the primary sprung mass of the wheelset; F pre is prestress of primary sprung.Calculating the wheel-rail impact force and impact velocity [9][10][11][12][13][14] The influence of flat length, depth, and vehicle speed on wheel-rail impact force The influence of wheel flat on the vehicle-track system dynamics [15][16][17][18][19][20] The influence of flat on wheel-rail contact response [21] The influence of flat on wheel wear The influence of wheel flat on traction drive system [22][23][24] The influence of flat on gear system [25] The influence of flat on traction motor [26] The influence of flat on wheel-rail impact under traction and braking conditions

IET Electrical Systems in Transportation
When , critical speed v 0 can be expressed as follows: where r is the radius of the wheel.According to Zhai [27], when the vehicle speed is less than the critical speed, the wheel impact speed can be calculated as follows: where γ is the coefficient for converting the rotational inertia of wheels into reciprocating inertia, L f is the length of the wheel flat.When the vehicle speed is larger than the critical speed, the wheel impact speed can be calculated as follows: 3. Electromechanical Coupling Model In the modal analysis of the wheelset, it is assumed that the wheel and gear are rigidly attached to the axle without considering their relative motion.An 8-node and 6-hexahedral element discretization is employed for the wheelset.The wheelset is assumed to have free boundary conditions, and the Lanczos method is used to calculate its modal characteristics.Figure 5 shows the mode shapes and natural frequencies of the first 8order modes of the flexible wheelset.As the wheel flat mainly induces vertical vibration impacts between the wheel and rail, the first bending mode may be excited, resulting the presence

IET Electrical Systems in Transportation
of vertical oscillation components around 82 Hz in the wheel-rail contact parameters.
The track system model is simplified as a double-mass (rail pad and sleeper), three-layer (rail-sleeper-ballast) springdamping model; the detailed modeling parameters are shown in Table 3. Equivalent spring-damping units are used to connect these components of the track system.The accuracy of the vehicle-track coupling dynamics model has been verified in the authors' previous work [3].The wheel-rail coupling subsystem mainly consists of the normal contact and tangential contact models.The Hertz contact theory is used to simulate the normal contact for the wheel-rail system [29], while the FASTSIM algorithm is responsible for the tangential contact [30][31][32].
The primary function of this subsystem is to calculate the wheel-rail normal forces, creep forces, and size of the contact patch.In the Hertz contact theory, the contact patch between the wheel and rail is equivalent to an ellipse and can be represented as follows [29]: where a and b denote the long half-axis and short half-axis of the ellipse, respectively, A and B denote longitudinal and lateral relative curvature; P denotes wheel-rail normal force; G * is determined by the materials of the wheel and rail, and can be represented as follows: where v r and E r are Poisson's ratio and elastic modulus of rail material, respectively, v w and E w are Poisson's ratio and elastic modulus of wheel material, respectively.The main function of Hertzian theory is to solve the distribution of normal force, which can be expressed as follows [31]: Wheel-rail creepage is an important parameter for evaluating wheel-rail contact performance.According to Yang et al. [22], when the wheel-rail contact is in a full sliding state, the calculation of the wheel-rail creepage needs to consider the relative vibration speed between the wheel and the rail.The wheel-rail creep force can be expressed as follows: where μ denotes the friction coefficient between the wheel and rail, which can be calculated as follows: where a μ ; b μ ; x μ ; y μ are the key parameters that affect the friction coefficient.v slip represents the relative slip speed between wheel and rail, which can be calculated by wheel angular velocity ω and vehicle forward velocity v. Thus, relative slip speed v slip can be expressed as follows [33]: where r is the wheel radius.
The main objective of this paper is to investigate the impact of wheel flats on the vibration of the traction drive system.Therefore, it is necessary to incorporate the initial defect of the wheel into the locomotive-track coupling dynamics model.According to Li et al. [34], the wheel flat can be described using a cosine function, which can be represented as follows: where D f is the depth of the wheel flat, L f is the length of the wheel flat.The relationship between the length and depth of wheel flat can be expressed as follows: 3.2.Electric Traction Drive System.The electric traction drive system, as the power source for locomotive operation [35][36][37][38], mainly consists of rectifiers, DC links, inverters, and traction motors [39][40][41][42], as shown in Figure 6.Singlephase 25 kV AC power from the traction grid is converted to DC 1,800 V power through the rectifier [43][44][45].In this system, the speed control method for the motor is variable frequency control [46][47][48].Therefore, the DC power is converted to three-phase AC power with variable amplitude and frequency through the inverter, which is then supplied to the asynchronous motor.A Simulink model of the electric traction system is constructed, with specific modeling parameters shown in Table 4.The rectifier adopts transient current control [49,50], while the inverter-motor system uses indirect field-oriented vector control [41,51,52].

Coupling of Electrical and Mechanical Parts of Traction
Drive System.The traction motor converts electrical energy from the electric traction drive system into mechanical energy in the form of electromagnetic torque, which is then transmitted to the gearbox to drive the wheels and propel the vehicle [53,54].Therefore, the traction motor itself is an electromechanical coupling module.By establishing a closed-loop feedback between the electric traction drive system model in Simulink and the locomotive-track coupled dynamics model in SIMPACK, the electrical side and mechanical side of the drive system are coupled together.Specifically, the torque output from the motor in Simulink is applied to the motor shaft in SIMPACK, while the rotor speed output from SIMPACK is fed back to the motor control system in Simulink.The transfer of these parameters is facilitated through the interface SIMAT between Simulink and SIMPACK, ensuring real-time interaction and closed-loop feedback between the electrical and mechanical systems, as shown in Figure 7.

Analysis of Simulation Results
From the locomotive wheel out-of-roundness experiments, it is known that wheel flats exhibit various patterns.In order to fully investigate the impact of wheel flats on the traction drive system, this paper adopts a controlled variable method to consider the effects of different lengths and depths of flats.
Additionally, this study takes into account the impact of wheel flats on the drive system under different locomotive operating speeds.Specifically, three simulations are conducted: Due to the presence of initial wheel defects (flats), there will be instability in the locomotive-track coupled dynamics during the initial stage of operation.Therefore, the dynamic model undergoes free uniform linear motion from 0 to 10 s.After 10 s, the mechanical and electrical parts of the traction drive system are coupled.It is worth noting that this approach is employed for all subsequent simulations in this paper.Key data from the electrical and mechanical sides of the traction drive system are obtained, such as the wheel-rail normal force, creepage ratio, contact patch characteristics, rotor speed, and torque, as shown in Figures 9-16.
From Figure 9(a), it can be observed that as the flat depth increases, there is an increasing fluctuation in the wheel-rail normal force.Figure 10 shows the wheel-rail normal force with and without torque excitation.When the wheel rolls over the flat, there is a significant impact between the wheel and the rail, which then gradually attenuates.Comparing Figures 10(a) and 10(b), it can be seen that without torque excitation, the wheel-rail normal force essentially attenuates to a stable state.However, in the presence of torque excitation, the normal force first attenuates and then continues to exhibit small-amplitude oscillations.The fast Fourier transform (FFT) [55] analysis of the normal force reveals that the main fluctuation frequency is 90 Hz, which is attributed to the vibration impact caused by the wheel flat exciting the first bending mode of the flexible wheel (as seen in Figure 5).
The longitudinal creepage, lateral creepage, and spin creepage between the wheel and rail are shown in Figures 11-13,  Figure 14 illustrates the size of the contact patch between the wheel and rail.It can be observed that an increase in the depth of the wheel flat leads to a larger contact patch.This result corresponds to the wheel-rail normal force shown in Figure 9. Due to the wheel-rail vibration impact caused by the flat, when the normal force reaches the peak value, the size of the contact patch between the wheel and rail also IET Electrical Systems in Transportation reaches the peak value.Accordingly, the frequency of the contact patch size fluctuations aligns with that of the normal force.
Figure 15 presents the rotor angular velocity of the motor.It can be observed that variations in the depth of the wheel flat have a relatively small impact on the fluctuation of the rotor speed.When the depth of the flat increases, there is a slight increase in the fluctuation of the rotor speed.From Figure 15(b), it can be seen that the frequency of the rotor speed fluctuations is also around 90 Hz.Comparing the dynamic parameters shown in Figures 9-15, it can be concluded that the vibration impact caused by the wheel flat primarily manifests in the vertical direction and has a relatively minor influence on the rotor rotation.

IET Electrical Systems in Transportation
The motor torque from the electric traction drive system is shown in Figure 16.It can be seen that variations in the depth of the wheel flat have a minimal impact on the torque.As the depth of the wheel flat increases, the torque remains consistent in both the time domain and frequency domain.The transient current mentioned in Section 2.1 of the electric traction drive system, which is responsible for the invertermotor.Field-oriented vector control is developed based on PI control.PI control has a certain degree of disturbance rejection capability.Therefore, despite the fluctuations in rotor speed feedback to the electric traction transmission system caused by the wheel flat depth variation, the motor torque output can remain unchanged.

The Impact of Wheel Flat Length on Traction Drive
System.According to the simulation settings in Test 2, the electromechanical coupling model established in Section 3 was operated to obtain the mechanical and electrical parameters of the traction drive system.The temporal and spectral characteristics of the wheel-rail normal force are shown in Figure 17.When the flat length is 0.05 m, the vibration impact between the wheel and rail is exceptionally large.The minimum value of IET Electrical Systems in Transportation the normal force has already reached zero, indicating the occurrence of wheel-rail separation.It is worth noting that the spectral characteristics of the normal force at the flat length of 0.05 m are different from the other cases.In other cases, the frequency of the normal force fluctuation is mainly centered around 90 Hz.However, when L f = 0.05 m, the frequency of the normal force fluctuation is mainly centered around 270 Hz, which is close to the second-order umbrella mode of the flexible wheelset (as can be seen in Figure 5).This indicates that the second-order umbrella mode of the wheelset is excited in this case.In Figure 18, it can be observed that as the wavelength of the flat decreases, the vibration impact of the normal force becomes more pronounced, and simultaneously, the rate of vibration attenuation slows down.IET Electrical Systems in Transportation and spin creep is mainly centered around 90 Hz.However, when L f = 0.05 m, the fluctuation frequency of the spin creep is mainly centered around 275 Hz, but there is also a significant component at 90 Hz.The temporal and spectral characteristics of the wheel-rail contact patch size are shown in Figure 22.Similar to the analysis in Section 4.1, the fluctuation characteristics of the contact patch size correspond to those in the normal force.As the flat length increases, the fluctuation of the contact patch size decreases.Except for the case with a flat length of 0.05 m, the fluctuation frequency is mainly centered around 90 Hz.
The temporal and spectral characteristics of the motor rotor angular velocity are shown in Figure 23.Except for the case with a flat length of 0.05 m, the fluctuation of the motor rotor speed is not sensitive to changes in the wheel flat length, and its main fluctuation frequency is mainly centered around 90 Hz.In the extreme case of L f = 0.05 m, the rotor speed exhibits larger fluctuations, but it is important to note that its main fluctuation  IET Electrical Systems in Transportation frequency still remains centered around 90 Hz. Figure 24 presents the temporal and spectral characteristics of the motor torque.It can be seen that due to the anti-interference characteristics of the PI control, the motor output torque is not significantly affected by changes in the wheel flat depth. of the traction drive system.Figure 25 shows the wheel-rail normal force at the speed range of 60-100 km/hr.It can be observed that as the locomotive speed increases, the wheel flats can cause larger fluctuations in the normal force.From the spectral characteristics of the normal force in Figure 25(a), it can be seen that the main frequency of the fluctuation is around 90 Hz.However, it should be noted that as the locomotive speed increases, the components at 168 and 275 Hz gradually increase, which correspond to the first-order and second-order umbrella modes of the wheelset, as shown in 12 IET Electrical Systems in Transportation Figure 2. Figure 26 shows the temporal characteristics of the wheel-rail normal force within the time span of 2.1-2.7 s at different speed levels.To clearly display the oscillation period of the normal force, we have shifted the normal force along the vertical axis for each speed.As the wheel rolling speed increases, the oscillation period of the normal force becomes shorter.This means that the normal force has not completely reached a steady state before the next impact occurs.This is the reason why the fluctuation of the normal force increases as the locomotive speed increases.The longitudinal, lateral, and spin creepage of the wheelrail contact at different speeds are shown in Figures 27-29  IET Electrical Systems in Transportation the contact patch size increases with the locomotive speed.From Figure 30(b), it can be seen that the fluctuation of the contact patch size contains components at 90, 168, and 275 Hz, which is similar to the normal force.As the locomotive operates at different speeds, the rotor speed of the motor also varies.To compare the rotor fluctuations at different speeds more clearly, the measured rotor speed waveform is subtracted by its mean value, as shown in Figure 31.The rotor speed fluctuations are not sensitive to changes in locomotive speed.When the locomotive speed increases from the range of 60 to 90 km/hr, the rotor speed fluctuations remain relatively unchanged.However, when the locomotive operates at 100 km/hr, there is a significant increase in rotor speed fluctuations.The fluctuation frequency of the rotor speed is mainly centered around 90 Hz.
Since the resistance experienced by the locomotive is related to the running speed, the required traction torque output from the motor varies at different speed levels.To depict the variation in torque fluctuations more clearly, the waveform of the motor output torque at different running speeds is subtracted by its mean value, as shown in Figure 32.When the locomotive operates in the range of 60-90 km/hr, the torque fluctuations slowly increase with the locomotive speed.However, when the locomotive speed reaches 100 km/hr, there is a significant increase in torque fluctuations.It is worth noting that there are distinct differences in torque fluctuations before and after applying torque excitations.The torque mainly contains fluctuations at 90 Hz.

Conclusions
Based on the electromechanical coupling system of the electric traction drive system and the locomotive-track coupling dynamics system, this study investigated the impact of wheel flats on the locomotive traction drive system.The following important conclusions can be drawn: (1) Wheel flats can excite the first-order bending mode of the wheel-rail system, leading to significant fluctuations in the dynamic responses of the wheel-rail system and rotor speed, primarily at a frequency of 90 Hz.(2) The wheel-rail normal force, creepage, and contact patch area are significantly influenced by changes in

16
IET Electrical Systems in Transportation the depth of wheel flats.As the depth of the flats increases, the magnitude of these parameters' fluctuations also increases.However, the rotor speed and torque are not significantly affected by changes in the depth of wheel flats.
(3) The wheel-rail normal force, creepage, contact patch area, and rotor speed are sensitive to changes in the length of wheel flats.Smaller flat lengths result in larger fluctuations in these parameters.Again, the torque is not significantly affected by changes in the length of wheel flats.When the flat length reaches 0.05 m, the wheel-rail system experiences severe vibrations, leading to wheel-rail separation.(4) With increasing locomotive speed, the impact of wheel flats on electrical and mechanical parameters becomes more significant.When the locomotive speed reaches 100 km/hr, there is a noticeable increase in torque fluctuations.

FIGURE 2 :
FIGURE 2: The motion characteristics of a wheel with flats at low speeds.

FIGURE 3 :
FIGURE 3: The motion characteristics of a wheel with flats at high speeds.

3. 1 .
Locomotive-Track Coupling Dynamics Model.The locomotive-track coupled dynamics model mainly consists of three parts: the locomotive dynamics model, the track subsystem model, and the wheel-rail coupling subsystem model, as shown in Figure 4. Based on the vehicle dynamics theory [24, 28] and the actual locomotive parameters listed in Table 2, a detailed locomotive dynamics model is established in SIMPACK.The model includes one body, two bogies, six wheelsets, and six motors.The motor suspension in this locomotive is axle-hung, so only the vertical and pitch degrees of freedom of the motors are considered, while the other components are considered to have 6 degrees of freedom.The wheelsets are treated as flexible bodies, and their modal analysis results are shown in Figure 5.

) 4 . 2 × 10 2
Mass moment of inertia of motor (kg • m 2 ) 2 × 10 2 Stiffness of primary suspension (N/m) 3.14 × 10 6 Stiffness of secondary suspension (N/m) 2.14 × 10 6 Stiffness of suspension connecting motor and bogie frame (N/m) 1.0 × 10 10 Stiffness of axle-hung bearing supporting motor on wheel axle (N/m) 1.0 × 10 10 Damping coefficient of primary suspension (N s/m) 5 × 10 4 Damping coefficient of suspension connecting motor and bogie frame (N s/m) 9 × 10 4 Damping coefficient of secondary suspension (N s/m) 1.0 × 10 3 Damping coefficient of axle-hung bearing supporting motor on wheel axle (N s/m) 1.0 × 10 3 Semi-longitudinal distance between bogies (m) 5.03 Semi-longitudinal distance between wheelsets in bogie (m) 1.3 The longitudinal distance between bogie center and hung position of motor on bogie (m) 0.374 Longitudinal distance between pinion center and hung position of motor on bogie (m) 0.35 Distance between centers of pinion and gear (m

FIGURE 5 :
FIGURE 5: Modal analysis results of flexible wheelset.

Test 1 :
The locomotive operates at a speed of 70 km/hr, with a flat depth of 0.24 mm.The range of the flat lengths is from 0.05 to 0.35 m, with an interval of 0.1 m, as shown in Figure8(a).Test 2: The locomotive operates at a speed of 70 km/hr, with a flat length of 0.25 m.The range of flat depths is from 0.18 to 0.36 mm, with an interval of 0.06 mm, as shown in Figure8(b).Test 3: The flat length is 0.25 m, and the flat depth is 0.24 mm.The locomotive operates at a speed range of 60-100 km/hr.4.1.The Impact of Wheel Flat Depth on Traction Drive System.According to the simulation settings in Test 1, the electromechanical coupling model established in Section 3 is operated.

FIGURE 7 :
FIGURE 7: Diagram of the electromechanical coupling model.

4. 3 .
Impact of Wheel Flats on the Traction Drive System at Different Speeds.Based on the simulation settings in Test 3, the electromechanical coupling model established in Part 3 is operated to obtain the mechanical and electrical parameters

TABLE 1 :
Classification of wheel flat research.

TABLE 2 :
Parameters of the vehicle system.Mass moment of inertia of car body (kg • m 2 ) 1.434 × 10 6 Mass moment of inertia of bogie frame (kg • m 2 ) 1.311 × 10 4 Mass moment of inertia of wheelset (kg • m 2

TABLE 3 :
Parameters of track system.

TABLE 4 :
Modeling parameters of electric traction drive system.