Abstract
Nanobiotechnology is a unique class of multiphase and recently become a branch of contemporary science and a paradigm shift in material research. One of the two main problems facing the field of nanomaterial synthesis is the discovery of new natural resources for the biological production of metal nanoparticles and the absence of knowledge about the chemical composition of bio-source required for synthesis and the chemical process or mechanism behind the production of metal nanoparticles presents the second difficulty. We reported template-free green synthesized copper oxide nanoparticles using Tribulus terrestris seed natural extract without any isolation process. XRD, TEM, SEM, UV–Vis, DLS, zeta potential, and BET evaluated the synthesized metal nanoparticle. The TEM analysis confirmed that the CuO NPs are well dispersed and almost round in shape with an average size of 58 nm. EDAX confirms that copper is the prominent metal present in the nanomaterial. The greener fabricated copper oxide nanoparticle was employed to degrade methyl orange dye, almost 84% of methyl orange was degraded within 120 min. The outcomes demonstrated the nanomaterial’s effective breakdown of contaminants, highlighting their potential for environmental rehabilitation. The electrochemical investigation of the CuO NPs was utilized for supercapacitor application. An appreciable value of specific capacitance is 369 F/g specific capacitances with 96.4% capacitance retention after 6000 cycles. Overall, the results of the current study show that the biologically produced copper oxide nanoparticles have intriguing uses as photocatalysts for treating water contaminants and are suitable for energy storage devices.
Similar content being viewed by others
Introduction
As a result, a tremendous amount of undesired man-made trash is dumped into the environment, causing serious environmental issues like pollution and causing severe ecological balance 1,2. So, nowadays researchers are looking to find new materials for a better environment. The basic criteria of the new material should satisfy multiple efficacies, with the properties of non-toxic, and environmentally safe and the preparation method should be eco-friendly and simple 3. The green synthesis method is one of the eco-friendly, safer methods due to the lessened usage of harsh chemicals 4,5,6. Plant-derived nanomaterials are a faster, straightforward, economical saver, and non-toxic technique than other methods. Intriguingly, the phytochemicals found in plant extracts—“terpenoids, alkaloids, phenols, tannins, flavonoids, saponins, secondary metabolites”, etc. would act as natural surfactants, reducing agents, capping agents, and stabilizing agents during the synthesis 1,3,7,8,9. There have been numerous reports of biogenic synthesis of different metal/metal oxide nanoparticles for various applications like energy storage, photocatalyst, medical engineering, drug delivery, sensing and tissue engineering, etc7,10,11 due to the high conductivity, large surface-to-volume ratio, plasmonic properties and so forth. The next generation of advanced technologies such as green nanotechnology, advanced materials and composites, and nanostructures for environmental remediation, wastewater treatment, renewable and clean energy production, and storage, addressing environmental issues, and electrochemical applications. Fabricating heterogeneous metal composites and engineered nanostructures has received more attention due to the good chemical stability in aqueous solution, desirable optical properties, and electrochemical properties. In the case of composites like SrTiO312, Nd2Sn2O713and CoFe2O4@SiO2@Dy2Ce2O7 14 for photocatalytic applications, and CeVO4/rGO 15 and Nd2Sn2O7 16 Zn3V3O8 17 for hydrogen storage and Pr2Ce2O7 18 and Pr6O1119 for electrochemical quantifications were synthesized. The other side is simple metal nanoparticles (Cu, Ni, Mn, Mg, V, Pt, Pd, Fe, Sn, and Ag), among all copper nanomaterials, have found appropriate applications due to their non-toxicity, availability, affordability, and ease of fabrication in the form of nanoscale materials. The current work focuses on the bioinspired synthesis of copper oxide nanoparticles (CuO NPs) utilizing the seed extract of Tribulus terrestris as a green reducer and surfactant in the biogenic synthesis of CuO NPs.
For the production of copper oxide NPs, various techniques have been employed by different researchers for different purposes. These consist of wet electrodeposition20,21,22 and chemical deposition23,24, chemical reduction techniques (hydrothermal)19,20,21,22, and others. These techniques require high pressure and temperature, and the majority employ hazardous chemicals that are harmful to people and the environment 25,26. Moreover, different plant extracts have been used to synthesize CuO NPs namely, Moringa oleifera plant extract 27, Ficus benghalensis leaf extract 28, Clerodendrum phlomidis extract 29, sugarcane molasses 30, mimosa leaves extract 31 for energy storage applications. Commelina benghalensis leaf extract 32, Carica papaya extract 33, and lemon peel 34 for dye degradation. Furthermore, apart from common metal nanoparticles like Zn, Au, Ag, Pt, and Ni. The new composites and advanced nanostructures were also tried for photocatalytic applications namely the facial synthesis of Pr2Ce2O7 35, Nd2Sn2O7 13, and Dy2O3–SiO2 36 ZrO237, and Sn–Ln mixed-metal oxides38 to enhance the material properties for pollutant degradation. Preparation of advanced materials composites, and nanostructures via a simple and green method and investigation of their performances is another domain of material research for specific applications.
In this work, we used natural extracts from fresh T. terrestris seed to synthesize simple CuO NPs and studied their potential for electrochemical energy storage application and photocatalyst. These days, dangerous chemicals like organic dyes are the main source of contaminated water. Organic dyes are widely utilized as colorants in a variety of industries, including printing, textiles, paper, food, medicine, and cosmetics. Numerous industrial effluents and organic dyes are frequently dumped into water bodies without adequate treatment. The high toxicity, carcinogenicity, and non-biodegradability of these dyes and their derivatives lead to a host of issues, including skin disorders, liver and kidney failure, and poisoning of living organisms' neurological systems. Developing an economical and environmentally friendly substitute for the breakdown of organic dyes in wastewater is crucial as the existing techniques for eliminating harmful materials from water bodies are both expensive and ineffective 19,26,28.
On the other hand, Due to their intermittent nature, energy storage is one of the main challenges faced by the majority of renewable energy sources, including wind and solar power 39,40,41. Over the past few decades, a variety of electrochemical energy storage devices, including fuel cells, various types of batteries, supercapacitors, and hybrid systems, have been developed 41,42. Among all supercapacitors have quick charge and discharge, long cycle life, and higher power densities than batteries. They can be used in various devices, including power electronic devices, solar cells, and biomedical sensors. Bioresources and biowaste materials can also be utilized to create supercapacitor electrodes 43,44,45. Two types of SCs are distinguished by their mechanisms of charge storage: the electric double-layer capacitor (EDLC) and the Faradaic reversible redox reaction of the pseudocapacitor (PC). In comparison to other conventional capacitors and the EDLC, the PC has a high specific capacitance and energy density. As a result, recent research has concentrated on creating PC electrodes to improve the performance of SCs. Because of their low cost, earth abundance, multi-oxidation states, high conductivity, and good stability, transition metal oxides have been regarded as active PC materials. When compared to pure metals and their oxides, metal-doped metal oxide nanostructures were specifically mentioned as promising pseudocapacitive electrodes. Prior studies have unequivocally shown that Ca doped with CuO electrodes improves electrochemical SCs' endurance, capacitance, surface area, and conductivity 42. As a result, the novelty of this work combines the benefits of employing sustainable resources with those of green chemistry concepts. In addition, synthesized CuO NPs have been observed to satisfy the important parameters of ecological material for dual roles such as photocatalysts used to degrade methyl orange and green electrodes for energy storage applications with good results. and (Fig. 1). In short, the findings of our research work may be considered serious, talented, and novel, suggesting that copper oxide synthesis via green synthesis might be engaged as a cost-effective and efficient adsorbent for pollutant adsorption and has wonderful potential for wastewater treatment and has the ability to store the energy for future energy devices—“Green material for a greener environment (dye degradation) and green energy (supercapacitor)”.
Method and materials
Chemicals list
We utilized analytical grade (AR) chemicals: Copper sulfate, N-N-Methyl pyrrolidone, PVDF, Nickel foam, KOH, and methyl orange were purchased from Sigma Aldrich and Merck companies and used as purchased, and no further purifications.
Tribulus terrestris assisted synthesis of CuO
The CuO-NPs were synthesized by a traditional bio-reduction process by T. terrestris seed collected from Javadhu Hills, Eastern Ghats, Tamil Nadu, India. The appropriate permissions for collecting plant specimens were obtained from the administration affiliated with the Government of Tamil Nadu, India. Since it is a wild species flowers have been collected for our research and field study under the permission of competent authority of the State Forest Department, Govt. of Tamil Nadu. According to IUCN’s Red List Categories and Criteria, globally T. terrestris comes under the Least Concern (LC) category. We confirm that the collection of plant material complied with relevant institutional, national, and international guidelines and legislation.
20 g of T. terrestris seed was ground to form a powder by using mortar and pestle. ~ 2 g of T. terrestris seed powder was added into 50 ml of 0.2 M CuSO4 solution, stirred for 10 min, and heated in the hot plate at 60 °C for 1 h. The formation of CuO–NPs can be confirmed by color transformation to dark brown. The prepared solution was decanted and washed residue to remove gross by 50% alcohol and H2O followed by drying at 80 °C in a hot air oven.
Material characterizations
High-resolution transmission electron microscopy (HR-TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) was performed in FEI TECNAI T20G2. Field emission scanning electron microscopy with Energy-dispersive X-ray spectroscopy was carried out in SU 8000, Hitachi, Tokyo, Japan. X-ray Diffraction (XRD) patterns were recorded at room temperature by JEOL JDX 8030. X-ray photoelectron spectroscopy (XPS) was carried out at Axis ultra DLD spectrometer (Kratos Co., UK) with a monochromatic Al-Kα X-ray source (1486.6 eV). The surface phenomenon was studied by atomic force microscope (INNOVA, USA), and the surface area analysis by Gemini VII 2.00. UV–Visible spectroscopy (UV–Vis) was carried out in JASCO V-560 and the photoluminescence by LABRAM (HR800) to study the optical properties of the extract and synthesized CuO-NP with diffuse reflectance. Fourier transforms infrared (FT-IR) spectroscopy was carried out in JASCO 440 plus. TGA-50 HIMADZU recorded thermogravimetric analysis. The zeta potential of the synthesized CuO NPs was analyzed by a 90-plus particle size analyzer (DR-525, Brookhaven Instruments Corporation, USA).
Electrochemical characterization
All electrochemical characterizations were analyzed in CHI660E, USA. For electrochemical measurements, Ni foam is a working electrode, Platinum wire is the auxiliary electrode, and Ag/AgCl is the reference electrode. 0.5 ml of N-N-Methyl pyrrolidone (NMP), the solution was mixed with 1 mg of bio-synthesized CuO–NPs, and 10% PVDF binder and made as a paste. The slurry paste was painted on the pre-cleaned Ni foam (1 × 1 cm) and dried for 2 h at 25 °C and 3 M KOH solution as an electrolyte. The CV experiment was tested between the potential window of 0–0.65 V at various scan rates. The GCD curves were analyzed in the voltage range of 0 to 0.6 V at different current densities. Furthermore, EIS in the frequency of 0.001 kHz with a 5 mV amplitude was analyzed. The specific capacitances were calculated using a formula (1).
whereas i = constant current, m = mass of active materials (mg) on the electrode surface, ∆t = galvanostatic discharge time in sec, and ∆v = applied potential window in volts.
Photocatalytic activity of CuO NPs
The synthesized CuO NPs were used as a catalyst against methylene orange. A Heber multi-lamp photoreactor HML MP 88 with medium-pressure mercury vapor lamps (8W) was used for irradiation. As much as 100 mL of methylene orange solution (2.0 × 10–5 M) was mixed in a beaker containing 100 mg of synthesized CuO NPs. During the experiment, the mixture was continuously stirred and samples were collected every hour. UV–Vis spectrophotometer was used to observe the variation in dye absorption within the range of the 400–800 nm range. The outcome of the experiment was expressed as the percentage of degradation efficiency. Degradation efficiency (%) = initial absorbance(C0)- final absorbance(C)/initial absorbance(C0) X 100. Also, the obtained results are compared with recently synthesized CuO NPs by various methods.
Mechanism of bioreduction
The major constitution of T. terrestris seed is kaempferol, astragalin, tribuloside, kaempferol 3-rutinoside, rutin, quercetin, harmane, coumaroyl-tyramine, ferulic acid, caffeoyl-tyramine, feruloyl-octopamine, coumaroyl-quinic acid 46. Those phytonutrients play an important role in the Bioreduction process and will act as capping agents to reduce metal ions into nanometal oxides (Mechanism 1)9,47
Results and discussion
Exploring optical properties of Biosynthesized CuO NPs
UV–Vis spectroscopy
The optical property of the synthesized CuO-NPs and seed extract is shown in Fig. 2a. The copper salt complexes are formed when the ions are reduced to form nanoparticles which were caused by the phytonutrients in the seed extracts. We utilized UV–Vis spectroscopy to analyze the color change in the produced solutions within the 200–800 nm range. Because of CuO NPs’ core electrons’ interband transition, For the production of CuO NPs, the broad peak center at 290 nm was observed and showed a drastic change from the T. terrestris seed extract. A significant absorbance peak between 250 and 300 nm was found by Sankar et al.33, which suggests the production of CuO NPs and the bandgap of 3.1 eV obtained from the Tauc’s plot.
Photoluminescence
The PL spectra dictate the important parameters of electronic energy transfer in nanoparticles and it varies based on the size and shape of the NPs, and additionally the excitation wavelength determination of the emission peak. At the excitation level of 390 nm and RT, PL spectra of as-synthesized CuO NPs were depicted in Fig. 2b. Normally, CuO is a p-type semiconductor, and the peaks vary due to the oxygen holes, surface defects, interstitial ion effect, and electron recombination between the donor and acceptor region of the nanoparticle. CuO Nps exhibited broad violet luminescence at 390 nm and the emission peaks were found at 390 nm and a feeble peak at 475 nm due to the band-edge emission and artifact 48.
Exploring surface properties and structural composition of Biosynthesized CuO NPs
FT-IR spectrum of CuONPs and seed extract
FT-IR spectra of synthesized CuO–NPs and the T. terrestris seed extract are depicted in Fig. 3a. The Cuo–NPs and T. terrestris seed extract show the different functional groups due to the bio-reduction process of CuO and the presence of flavonoids, and polyphenols in T. terrestris seeds. The bands at 3424 and 3221 cm−1 can be assigned as O–H stretching in the carboxylic moiety (–COOH) and the hydroxyl group. The peak of 2921, 2841, and 2902 cm−1 shows the C–H stretching of alkane, 1762 and 1645 cm−1 resembles weak C=O stretching compared with seed extract has strong stretching vibrations at 1535, 1340, and 984 cm−1 represents N–H, C–N, C=C due to the polyphenols, flavonoids, terpenoids, and tannic acid and fails to show intense M–O bond whereas, the synthesized CuO-NPs shows the fine high intense band at 616, 543 cm−1 due to the formation of Cu–O bond34,49 with T. terrestris seeds extract, this confirms the formation of copper oxide nanoparticle and Bioreduction process.
XRD of CuO NPs
The crystalline phase and structural information of T. terrestris-assisted CuO NPs were investigated by the XRD patterns as shown in Fig. 3b. The interplanar spacing (d) for the corresponding peaks can be calculated using Brass’s law, nλ = 2dsinθ. The XRD diffraction peaks of CuO at 2θ = 29.89°, 33.56°, 36.97°, 47.57°, 51.88°, 57.44°, 60.85, 65.35, and 74.61° assigned as (110), (002), (111), (200), (202), (002), (113) and (004)25,50. The peaks of the CuO NPs (monoclinic phase) match JCPDS card No. 01-080-1268 with an average crystallite size of 58.7 nm calculated using Debye–Scherrer’s equation.
Raman spectra
Previous analysis has demonstrated that CuO with a monoclinic structure has a space group symmetry of C2h6 and that the Raman active is attributed to three zone-center optical phonon modes of Ag and 2Bg. The three peaks, 271 cm−1, 342 cm−1, and 608 cm−1, respectively, correspond to the Ag, Bg(1), and Bg(2) modes of the copper oxide single crystal (Fig. 3c). The Raman active's peaks have widened and happened downshift in comparison to the Raman spectra of the CuO single crystal. The quantum confinement effect of the CuO nanoparticles is primarily responsible for the broadenings and blue shifts of the Raman peaks. CuO has 4 atoms in its primitive cell that give rise to 12 phonon branches. These consist of 3 acoustic modes (Au + 2Bu) and 9 zone-center optical phonon modes (4Au + 5Bu + Ag + 2Bg). However, only 3 symmetry modes (Ag + 2Bg) are Raman active. They are positioned at the peaks of 298 (Ag), 345 (Ag), and 632 cm−1 (Ag). The remaining 6 are IR-active (3Au + 3Bu). Only the oxygen atoms shift in the Ag and Bg Raman modes. They shift perpendicular to the b-axis in the case of the Bg modes. During the infrared active modes, both the O and Cu atoms are in motion. For the Au modes, the induced dipole moment is parallel to the b-axis. But for the Bu modes, it is perpendicular49,50.
XPS
XPS is the preferable technique to analyze the chemical composition and electronic nature of the synthesized material by distinction on binding energies Fig. 4. shows the survey spectrum of CuO and the elements of Cu, C, and O were noticed. The Survey spectra (Fig. 4a) of CuO exhibit binding energy peaks corresponding to carbon (Fig. 4b), oxygen (Fig. 4c), and copper (Fig. 4d). By deconvoluting the Carbon peak into three distinct peaks, we identified C–C, C–O–C, and C=O bonds present in the T. terrestris Seeds, supported by evidence from FT-IR analysis. The appearance of C–O–C and C=O peaks at 290 eV and 293 eV, respectively, suggests the presence of hydroxyl and carboxyl groups from the seed extract. In the high-resolution XPS spectrum of the Cu 2p region, two peaks located at binding energies of 915 eV and 952 eV, were found as Cu 2p3/2 and Cu 2p1/2, respectively. Additionally, two shake-up satellite peaks were observed at binding energies of 930 and 965 eV, providing evidence of an open 3d9 shell characteristic of the Cu+ state. Furthermore, the (Fig. 4c) O1s binding energy at 531 eV closely resembles that of O2− in CuO, confirming the formation of metal–oxygen (M–O) bonds in CuO. Overall, the XPS results validate the presence of specific chemical bonds and provide essential insights into the composition and electronic states within the CuO material 25,49,51.
Exploring morphology investigation of Biosynthesized CuO NPs
Zeta potential
The zeta potential of T. terrestris-assisted CuO NPs indicates the degree of repulsion between opposite, same-charged particles in the dispersion in terms of the magnitude of charges and is found to be − 29.2 mV (Fig. 5a) it demonstrates quite a stability of CuO NPs at ambient temperature. A solution or dispersion can resist aggregation when the absolute value of the particle zeta potential in the solution is high. If attraction prevails over repulsion due to low zeta potential absolute values of the particles in a solution, the dispersion breaks down and flocculates. It is commonly accepted that a threshold of either + 30 or 30 mV marks the basic boundary between stable and unstable suspensions. Typically, Stable particles have zeta potentials of at least + 30 mV, primarily based on fabricated nanomaterials52.
Dynamic light scattering
DLS analysis was carried out to calculate the particle size (Fig. 5b). The CuO NPs created in the bio-reduction process utilizing plant leaf extract were widely distributed in the solution, according to the particle size analysis, and the particles made from the solution were substantially disseminated in the mixture, with sizes of 58.96 nm. The DLS approach, which measures the hydrodynamic radius, highly coincides with the XRD calculated size. Furthermore, the Polydispersity Index was found to be 0.532 which suggests that CuO–NPs are also highly monodispersed49.
SEM, TEM, and EDAX analysis of synthesized CuO NPs
To visualize the synthesized CuO NPs morphology and size, TEM (Fig. 6a,b) and SEM images were captured under an ambient atmosphere as shown in the figures it is clear from the image the synthesized CuONPs are spherical with an average size of ~ 59 nm and coincide with XRD crystalline size. From the SEM image (Fig. 5c, the accumulation in the synthesized CuONPs discloses diverse dimensions. Furthermore, elemental conformation was confirmed by EDX (Fig. 5d) merged with SEM to track the elements in synthesized NPs, the weight and atomic percentage of the elements present are shown in the EDS spectra of the copper oxide nanoparticles. The peaks of copper (84.3%) and oxygen (15.6%) are dominating in the absence of other contaminants. Eventually, the peak at 8.0 keV, dictates the formation of CuONPs. There were no other gross in the synthesized CuONPs. The presence of intermediate points within the concentration circles observed in the CuO nanoparticles, as revealed by the selected area electron diffraction (SAED), suggests that the nanoparticles are crystalline. Furthermore, the pattern closely matches the XRD pattern depicted in Fig. 6c, providing additional evidence of the nanoparticles' crystallinity.
BET
The CuONPs sample was used for the BET test to measure pore size, surface area, and pore volume. An illustration of a type IV isotherm nature with the H-3 hysteresis loop according to IUPAC classification, Fig. 6d (pore size distribution is inset) showed that CuONPs have a mesoporous structure. According to the BET data, the CuONPs created in this experiment have substantially smaller pores and more surface area than was expected. Additionally, the produced CuONPs' N2 adsorption isotherm displayed a BET surface specific area (SSA) of 32 m2/g, a pore size is 3–50 nm and a pore volume is 0.137 cm−3/g.
Photocatalytic activity of MO
The photocatalytic experiment was conducted under three conditions: without the photocatalyst under light (Blank), with the photocatalyst in the dark (Dark), and with the photocatalyst under direct light. In this study, a concentration of 10 mg/L of methyl orange (MO) was selected as a model pollutant. It was found that the MO solution had a pH of 7.01. A Heber Multi lamp photoreactor HML MP 88 with medium-pressure mercury vapor lamps (8 W) was used for irradiation. In the experiment, we added 100 mg of CuO nanoparticles, synthesized using biological methods, to a 100 ml solution of methyl orange dye. Methyl orange dye has a chromophoric group, which gives it a maximum absorption at 464 nm. As shown in Fig. 6a, the dye's absorption reduces with increasing exposure to UV light, reaching a minimum after 120 min. The degradation efficiency is obtained 84.23% by using a photocatalyst. Here, we can see the cleavage of the chromophoric group (Mechanism 3) 53,54. Deamination from MO causes a blue shift from 464 to 440 nm as shown in Fig. 7a. Figure 7b shows a plot of dye concentration (C/CO) over time. A photocatalytic reaction (Mechanism 2a and b) produced sufficient hydroxyl radicals to degrade 84.23% of MO under UV light after 120 min. To confirm the efficiency of mineralization, COD values were used to evaluate the degradation part. We measured COD values before and after the photocatalytic treatment. A 120-min UV illumination significantly reduced COD values to 350 mg/l from 5020 mg/l. The degradation efficiency of bio-synthesized CuO nanoparticles is confirmed by the decreasing value of COD. Table 1 compares the various methods synthesized CuONPs for dye degradation of MO and Table 2 discusses the photodegradation efficiency of MO solutions on CuO nanoparticles obtained from different reaction conditions. TOF is one of the empirical parameters for the catalytic performance and is calculated using the below formula (2) and found to be TOF = 20.256 µ/min55,56.
Mechanism 2b of photocatalytic degradation of methyl orange dye.
CuO NPs green electrode for energy storage:
The electrochemical test was tested in a 3 M KOH as an electrolyte solution by a traditional 3-electrode system. Figure 8a shows the cyclic voltammetry of Ni foam loaded with 1 mg of biosynthesized CuO NPs modified-electrode at various scan rate ranges from 10 to 100 mV s−1 in the potential range of 0–0.65 V. The gradually increasing current value is noted while increasing the scan rate (Fig. 8b). The permanent faradic redox current responses were noticed generally Ni foam has a low current response compared to CuO NPs loaded Ni foam. The CuO NPs exhibited the largest integral area under the cyclic voltammetry curve and the highest current density in both anodic and cathodic peaks. The GCD was also examined in a three-electrode system using the same procedure described above. Figure 8c displays the recorded GCD curves of CuO NPs at 1 to 5 A/g. By reducing the current density, the Charge/discharge time is stabilized. The Specific capacitance values were calculated from the CV and found to be 369, 336, 312, 258, 209 Fg−1 for CuO NPs electrode at the scan rate of 10, 25, 50, 75, 100 mVs−1, and from the GCD found to be 632, 517, 430, 256 and 128 Fg-1 for current densities of 1,2,3,4,5 Ag−1 (Fig. 8d). Similarly, Ikhiya et al.29, synthesized similar CuO NPs using the moringa plant, and under the same electrochemical condition they achieved 338 F/g. In contrast, the Alturki 32 team synthesized CuO–AC (activated charcoal) from sugarcane molasses, and they attained only 245 F/g with 99% retention time, similarly, Ravichandran 31 group also reported CuO NPs with r-GO showed only 82.1 F/g of specific capacitance with 98% cyclic stability. We achieved 369 F/g of specific capacitance. As discussed earlier the heterogenous advanced material, copper composites such as CuFeS2 33 and CNT@TFcP/Cu 59 were synthesized for better capacitance. The recently reported CuO NPs and composites were compared with our results (Table 3). Our results shows better efficient capacitance than others.
The cycle stability of the prepared electrode plays an important role in energy applications. The prepared electrode was subjected to 6000 cycles of charge/discharge at a current density of 1 A/g and maintained 96.4% of its capacity retention (Fig. 9b). Furthermore, the EIS was tested in a high-frequency field, An EIS is recorded at a potential of 20 mV in 1 M KOH electrolyte between 100 kHz and 0.01 Hz. (Fig. 9a) Solution resistance (Rs) and Charge transfer resistance (Rct) were found to be 2.62 and 14.32 Ω. Having a lower value for Rs indicates the material is electrically conductive and that the active material is well attached to the current collector. Due to the high conductivity of the electrode during the reaction with electrolytes, the Nyquist plot does not show a semicircle in the high-frequency region or has a smaller Rct value as shown in Fig. 8a.
The plausible redox mechanism of CuO is presented below63:
Conclusion
In conclusion, the greener method was used to fabricate CuO NPs using T. terrestris seed natural extract with an average size of 58 nm. The main novelty of this work is to satisfy the important parameters of ecological material (greener material) for dual roles such as photocatalysts and green electrodes for energy storage applications with good results. The synthesized CuO NPS was used to serve as electrode materials in a supercapacitor. The CuO nanoparticles stand out among the prepared samples with the highest specific capacitance of 632 F/g at a current density of 1 A/g, a sizable rate of capacitance, and outstanding cyclic stability (96.4 percent after 6000 rounds). CuO nanomaterial has a high electrochemical efficiency due to its ability to provide more active sites, enhance electrical conductivity, and carry out charge transfer effectively. Recent experiments have shown that CuO is capable of destroying up to 84% of methyl orange dye within 120 min. These results suggest that CuO nanomaterial can be a valuable component in energy storage devices, such as supercapacitors. Furtherly, the synthesized CuO NPs degrade the organic pollutant of MO as well as the degradation of methyl orange dye by 84% within 120 min and the outcomes demonstrated the nanomaterial's effective breakdown of contaminants, highlighting their potential for environmental rehabilitation.
Our research has conclusively demonstrated that copper oxide synthesis through green methods is a highly effective and cost-efficient solution for pollutant adsorption. This innovative approach also has tremendous potential for wastewater treatment and energy storage in future energy devices. Our findings are a testament to the serious, talented, and novel research that we have conducted shows that synthesized copper oxide through green methods is a highly suitable solution for pollution control and energy storage devices.
Data availability
The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request.
References
Bagheri, A. R., Aramesh, N., Hasnain, M. S., Nayak, A. K. & Varma, R. S. Greener fabrication of metal nanoparticles using plant materials: A review. Chem. Phys. Impact. https://doi.org/10.1016/j.chphi.2023.100255 (2023).
Jamkhande, P. G., Ghule, N. W., Bamer, A. H. & Kalaskar, M. G. Metal nanoparticles synthesis: An overview on methods of preparation, advantages and disadvantages, and applications. J. Drug Deliv. Sci. Technol. https://doi.org/10.1016/j.jddst.2019.101174 (2019).
Iravani, S. Green synthesis of metal nanoparticles using plants. Green Chem. 13, 2638–2650 (2011).
Ying, S. et al. Green synthesis of nanoparticles: Current developments and limitations. Environ. Technol. Innov. https://doi.org/10.1016/j.eti.2022.102336 (2022).
Silva, L. P., Pereira, T. M. & Bonatto, C. C. Frontiers and Perspectives in the Green Synthesis of Silver Nanoparticles. Green Synthesis, Characterization and Applications of Nanoparticles (Elsevier, 2019). https://doi.org/10.1016/b978-0-08-102579-6.00007-1.
Marslin, G. et al. Secondary metabolites in the green synthesis of metallic nanoparticles. Materials https://doi.org/10.3390/ma11060940 (2018).
Shreyash, N. et al. Green synthesis of nanoparticles and their biomedical applications: A review. ACS Appl. Nano Mater. 4, 11428–11457. https://doi.org/10.1021/acsanm.1c02946 (2021).
Rafique, M., Sadaf, I., Rafique, M. S. & Tahir, M. B. A review on green synthesis of silver nanoparticles and their applications. Artif. Cells Nanomed. Biotechnol. 45, 1272–1291 (2017).
Mittal, A. K., Chisti, Y. & Banerjee, U. C. Synthesis of metallic nanoparticles using plant extracts. Biotechnol. Adv. 31, 346–356. https://doi.org/10.1016/j.biotechadv.2013.01.003 (2013).
Chopra, H. et al. Green metallic nanoparticles: Biosynthesis to applications. Front. Bioeng. Biotechnol. https://doi.org/10.3389/fbioe.2022.874742 (2022).
Khan, I., Saeed, K. & Khan, I. Nanoparticles: Properties, applications and toxicities. Arab. J. Chem. 12, 908–931 (2019).
Hosseinzadeh, G. et al. Synthesis of novel direct Z-scheme heterojunction photocatalyst from WO3 nanoplates and SrTiO3 nanoparticles with abundant oxygen vacancies. Surf. Interfaces 42, 103349 (2023).
Morassaei, M. S., Zinatloo-Ajabshir, S. & Salavati-Niasari, M. Nd2Sn2O7 nanostructures: New facile Pechini preparation, characterization, and investigation of their photocatalytic degradation of methyl orange dye. Adv. Powder Technol. 28, 697–705 (2017).
Zinatloo-Ajabshir, S. & Salavati-Niasari, M. Preparation of magnetically retrievable CoFe2O4@SiO2@Dy2Ce2O7 nanocomposites as novel photocatalyst for highly efficient degradation of organic contaminants. Compos. B Eng. 174, 106930 (2019).
Rezayeenik, M., Mousavi-Kamazani, M. & Zinatloo-Ajabshir, S. CeVO4/rGO nanocomposite: Facile hydrothermal synthesis, characterization, and electrochemical hydrogen storage. Appl. Phys. A Mater. Sci. Process. 129, 47 (2023).
Zinatloo-Ajabshir, S., Morassaei, M. S., Amiri, O., Salavati-Niasari, M. & Foong, L. K. Nd2Sn2O7 nanostructures: Green synthesis and characterization using date palm extract, a potential electrochemical hydrogen storage material. Ceram. Int. 46, 17186–17196 (2020).
Ghodrati, M., Mousavi-Kamazani, M. & Zinatloo-Ajabshir, S. Zn3V3O8 nanostructures: Facile hydrothermal/solvothermal synthesis, characterization, and electrochemical hydrogen storage. Ceram. Int. 46, 28894–28902 (2020).
Zinatloo-Ajabshir, S., Mahmoudi-Moghaddam, H., Amiri, M. & Akbari Javar, H. A facile green fabrication of sponge-like Pr2Ce2O7 nanostructure using sucrose for electrochemical quantification of anti-Parkinson drug pramipexole. Microchem. J. 195, 109480 (2023).
Hamzeh, S., Mahmoudi-Moghaddam, H., Zinatloo-Ajabshir, S., Amiri, M. & Razavi Nasab, S. A. Eco-friendly synthesis of mesoporous praseodymium oxide nanoparticles for highly efficient electrochemical sensing of carmoisine in food samples. Food Chem. 433, 137363 (2024).
Jankhunthod, S., Kaewket, K., Termsombut, P., Khamdang, C. & Ngamchuea, K. Electrodeposited copper nanoparticles for creatinine detection via the in situ formation of copper-creatinine complexes. Anal. Bioanal. Chem. 415, 3231–3242 (2023).
Chandran, C. et al. A covalent organic framework with electrodeposited copper nanoparticles: A desirable catalyst for the Ullmann coupling reaction. J. Mater. Chem. A Mater. 10, 15647–15656 (2022).
Zurita, N. & García, S. G. Comparative study of electrodeposited copper nanoparticles on different substrates for their use in the reduction of nitrate ions. Results Eng. 17, 100800 (2023).
Sun, P., Liu, B., You, Z., Zheng, Y. & Wang, Z. Graphene/copper nanoparticles as thermal interface materials. ACS Appl. Nano Mater. 5, 3450–3457 (2022).
Zefirov, V. V. et al. Effect of chitosan coating on polypropylene fibers on the deposition of copper ions. J. Appl. Polym. Sci. 139, 52111 (2022).
Chand Mali, S., Dhaka, A., Sharma, S. & Trivedi, R. Review on biogenic synthesis of copper nanoparticles and its potential applications. Inorg. Chem. Commun. https://doi.org/10.1016/j.inoche.2023.110448 (2023).
Bagheri, A. R., Aramesh, N., Hasnain, M. S., Nayak, A. K. & Varma, R. S. Greener fabrication of metal nanoparticles using plant materials: A review. Chem. Phys. Impact https://doi.org/10.1016/j.chphi.2023.100255 (2023).
Ikhioya, I. L. et al. The green synthesis of copper oxide nanoparticles using the Moringa oleifera plant and its subsequent characterization for use in energy storage applications. East Eur. J. Phys. 2023, 162–172 (2023).
Yadav, S., Rani, N. & Saini, K. Green synthesis of ZnO and CuO NPs using Ficus benghalensis leaf extract and their comparative study for electrode materials for high performance supercapacitor application. Mater. Today Proc. 49, 2124–2130 (2021).
Ravichandran, S., Radhakrishnan, J., Sengodan, P. & Rajendran, R. Biosynthesis of copper oxide nanoparticle from Clerodendrum phlomidis and their decoration with graphene oxide for photocatalytic and supercapacitor application. J. Mater. Sci. Mater. Electron. 33, 9403–9411 (2022).
Alturki, A. M. Benign feature for copper oxide nanoparticle synthesis using sugarcane molasses and its applications in electrical conductivity and supercapacitor. Biomass Convers. Biorefin. https://doi.org/10.1007/s13399-022-03303-5 (2022).
Nsude, H. E. et al. Green synthesis of CuFeS2 nanoparticles using mimosa leaves extract for photocatalysis and supercapacitor applications. J. Nanopart. Res. 22, 1–13 (2020).
Kumar, R., Kumar, K. & Thakur, N. Biosynthesis of CuO/Cu2O-ZnO nanocomposites via Commelina benghalensis leaf extract and their antibacterial, photocatalytic and antioxidant assessment. Inorg. Chem. Commun. 157, 111400 (2023).
Sankar, R. et al. Green synthesis of colloidal copper oxide nanoparticles using Carica papaya and its application in photocatalytic dye degradation. Spectrochim. Acta A Mol. Biomol. Spectrosc. 121, 746–750 (2014).
Sangeetha, A. & Abarna, B. Lemon peel assisted synthesis of copper oxide nanoparticles for photocatalytic degradation. Mater. Today Proc. https://doi.org/10.1016/j.matpr.2023.02.148 (2023).
Zinatloo-Ajabshir, S., Salehi, Z. & Salavati-Niasari, M. Preparation, characterization and photocatalytic properties of Pr2Ce2O7 nanostructures via a facile procedure. RSC Adv. 6, 107785–107792 (2016).
Mahdavi, K., Zinatloo-Ajabshir, S., Yousif, Q. A. & Salavati-Niasari, M. Enhanced photocatalytic degradation of toxic contaminants using Dy2O3–SiO2 ceramic nanostructured materials fabricated by a new, simple and rapid sonochemical approach. Ultrason. Sonochem. 82, 105892 (2022).
Zinatloo-Ajabshir, S. & Salavati-Niasari, M. Facile route to synthesize zirconium dioxide (ZrO2) nanostructures: Structural, optical and photocatalytic studies. J. Mol. Liq. 216, 545–551 (2016).
Zinatloo-Ajabshir, S. & Mousavi-Kamazani, M. Recent advances in nanostructured Sn−Ln mixed-metal oxides as sunlight-activated nanophotocatalyst for high-efficient removal of environmental pollutants. Ceram. Int. 47, 23702–23724. https://doi.org/10.1016/j.ceramint.2021.05.155 (2021).
González, A., Goikolea, E., Barrena, J. A. & Mysyk, R. Review on supercapacitors: Technologies and materials. Renew. Sustain. Energy Rev. 58, 1189–1206. https://doi.org/10.1016/j.rser.2015.12.249 (2016).
Kumar, S. et al. 0D to 3D carbon-based networks combined with pseudocapacitive electrode material for high energy density supercapacitor: A review. Chem. Eng. J. https://doi.org/10.1016/j.cej.2020.126352 (2021).
Huang, S., Zhu, X., Sarkar, S. & Zhao, Y. Challenges and opportunities for supercapacitors. APL Mater 7, (2019).
Yassine, M. & Fabris, D. Performance of commercially available supercapacitors. Energies (Basel) 10, 1340 (2017).
Conway, B. E., Birss, V. & Wojtowicz, J. The role and utilization of pseudocapacitance for energy storage by supercapacitors. J. Power Sour. 66, 1–22 (1997).
Raza, W. et al. Recent advancements in supercapacitor technology. Nano Energy 52, 441–473. https://doi.org/10.1016/j.nanoen.2018.08.013 (2018).
Le Fevre, L. W., Cao, J., Kinloch, I. A., Forsyth, A. J. & Dryfe, R. A. W. Systematic comparison of graphene materials for supercapacitor electrodes. ChemistryOpen 8, 418–428 (2019).
Ștefănescu, R., Tero-Vescan, A., Negroiu, A., Aurică, E. & Vari, C. E. A comprehensive review of the phytochemical, pharmacological, and toxicological properties of Tribulus terrestris l. Biomolecules https://doi.org/10.3390/biom10050752 (2020).
Abdelfatah, A. M., Fawzy, M., El-Khouly, M. E. & Eltaweil, A. S. Efficient adsorptive removal of tetracycline from aqueous solution using phytosynthesized nano-zero valent iron. J. Saudi Chem. Soc. 25, 101365 (2021).
Tamuly, C., Saikia, I., Hazarika, M. & Das, M. R. Reduction of aromatic nitro compounds catalyzed by biogenic CuO nanoparticles. RSC Adv. 4, 53229–53236 (2014).
Jillani, S., Jelani, M., Hassan, N. U., Ahmad, S. & Hafeez, M. Synthesis, characterization and biological studies of copper oxide nanostructures. Mater. Res. Express 5, 045006 (2018).
Bello, A., Dodoo-Arhin, D., Makgopa, K., Fabiane, M. & Manyala, N. Surfactant assisted synthesis of copper oxide (CuO) leaf-like nanostructures for electrochemical applications. Am. J. Mater. Sci. 2014, 64–73 (2014).
Sudha, V., Murugadoss, G. & Thangamuthu, R. Structural and morphological tuning of Cu-based metal oxide nanoparticles by a facile chemical method and highly electrochemical sensing of sulphite. Sci. Rep. 11, 3413 (2021).
Duman, O. & Tunç, S. Electrokinetic and rheological properties of Na-bentonite in some electrolyte solutions. Microporous Mesoporous Mater. 117, 331–338 (2009).
Sheikh, M. U. D., Naikoo, G. A., Thomas, M., Bano, M. & Khan, F. Solar-assisted photocatalytic reduction of methyl orange azo dye over porous TiO2 nanostructures. New J. Chem. 40, 5483–5494 (2016).
Wu, L. et al. Study on the adsorption properties of methyl orange by natural one-dimensional nano-mineral materials with different structures. Sci. Rep. 11, 10640 (2021).
Luque-Morales, P. A. et al. Zno semiconductor nanoparticles and their application in photocatalytic degradation of various organic dyes. Materials 14, 7537 (2021).
Fatima, B. et al. CuO–ZnO–CdWO4: A sustainable and environmentally benign photocatalytic system for water cleansing. Environ. Sci. Pollut. Res. https://doi.org/10.1007/s11356-021-14543-9/Published (2021).
Sharumathi, S. et al. Copper oxide-anchored ZnO nanoflakes for the enhanced photocatalytic degradation performance and mechanistic investigations. Phys. B Condens. Matter 670, 415336 (2023).
Shibu, M. C. et al. Hydrothermal-assisted synthesis and characterization of MWCNT/copper oxide nanocomposite for the photodegradation of methyl orange under direct sunlight. Diam. Relat. Mater. 134, 109778 (2023).
Teimuri-Mofrad, R., Hadi, R., Abbasi, H., Payami, E. & Neshad, S. Green synthesis of carbon nanotubes@tetraferrocenylporphyrin/copper nanohybrid and evaluation of its ability as a supercapacitor. J. Organomet. Chem. 899, 120915 (2019).
Nwanya, A. C. et al. Maize (Zea mays L.) fresh husk mediated biosynthesis of copper oxides: Potentials for pseudo capacitive energy storage. Electrochim. Acta 301, 436–448 (2019).
Sudhakar, Y. N., Hemant, H., Nitinkumar, S. S., Poornesh, P. & Selvakumar, M. Green synthesis and electrochemical characterization of rGO–CuO nanocomposites for supercapacitor applications. Ionics (Kiel) 23, 1267–1276 (2017).
Kumar, J. S. et al. One pot synthesis of Cu2O/RGO composite using mango bark extract and exploration of its electrochemical properties. Electrochim. Acta 193, 104–115 (2016).
Zhang, W. et al. Rose rock-shaped nano Cu2O anchored graphene for high-performance supercapacitors via solvothermal route. J. Power Sources 318, 66–75 (2016).
Author information
Authors and Affiliations
Contributions
J.M.: study conception and design, data collection, analysis and interpretation of results, Investigation, nanoparticle synthesis, and manuscript preparation N.K.: Investigation, Resources, Datacuration, Visualization, review and editing N.S.: Investigation, Resources, Datacuration, Visualization, review and editing P.S.: Investigation, Resources, Datacuration, Visualization, review and editing JT: Investigation, Resources, Datacuration, Visualization, review and editing A.S.K.: Conceptualization, Methodology, review and editing, Visualization, Supervision, Project administration, Funding acquisition K.S.K.: Conceptualization, Methodology, review and editing, Visualization, Supervision, Project administration, Funding acquisition.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Meena, J., Kumaraguru, N., Sami veerappa, N. et al. Copper oxide nanoparticles fabricated by green chemistry using Tribulus terrestris seed natural extract-photocatalyst and green electrodes for energy storage device. Sci Rep 13, 22499 (2023). https://doi.org/10.1038/s41598-023-49706-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-49706-w
This article is cited by
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.