Introduction

The generation of reactive oxygen species (ROS) is the backbone of advanced oxidation processes leading to widespread applications such as organic pollutant degradation1,2, cancer therapy3,4,5, and disinfection6,7,8. Among all different types of ROS, hydrogen peroxide (H2O2) is more stable than others9. As an environmentally friendly chemical, H2O2 not only plays an important role in various organic syntheses10,11,12 but can also be used as a bleaching agent and fuel in industry13,14. Conventionally, H2O2 is produced by the anthraquinone method, which involves some serious limitations, such as complicated reaction steps, where the products and byproducts are hardly separated15,16. Recently, photocatalysis and piezocatalysis have emerged as promising alternatives to produce ROS. In particular, the utilization of renewable energies to generate ROS has been widely investigated in recent years instead of traditional chemical methods17,18,19,20. Light irradiation and mechanical vibration provide the necessary stimuli in photocatalysis and piezocatalysis, respectively. Activated by external triggers, the electron-hole pairs are separated in photo/piezocatalysts and promote surface electrochemical reactions to generate ROS21. However, photocatalytic reactions are greatly affected, where suspended matter in wastewater causes low solution transmittance and thus restricts its quantum efficiency below 10%22,23. Moreover, in practical applications, round-the-clock performance is also hindered in photocatalysis due to the unavailability of sunlight24. On the other hand, the unavailability of suitable mechanical forces in nature creates a serious bottleneck for the realization of effective piezocatalytic performance. Hence, it is imperative to design efficient catalysts that can be exploited in an uninterrupted manner for ROS generation.

Temperature is one of the most important environmental factors, and a temperature difference exists almost everywhere in our living environment. The discovery of thermoelectric materials has paved the path to harness this waste heat or temperature difference for various applications, such as energy convertors and sensors25,26. In general, thermoelectric materials can convert thermal energy to electrical energy by means of the temperature difference-induced separation of positive and negative charges27. Temperature difference-induced charge separation and consequent voltage generation inside a thermoelectric material can also be expected to realize ROS generation and the corresponding catalytic activity28,29. Thermoelectric materials that can be used as catalysts are called thermocatalysts and are endowed with multiple advantages over traditional photo/piezocatalysts. Unlike photocatalysts or piezocatalysts, thermocatalysts show great promise towards the uninterrupted generation of ROS, as a temperature difference always exists in nature. Moreover, temperature difference-induced charge separation in thermocatalysts is beneficial for prohibiting electron-hole recombination, which further ensures higher ROS generation. However, despite these striking advantages, the investigation of ROS generation by thermocatalysts remains almost unexplored in the literature. Since the thermoelectric voltage under a particular temperature difference plays the key role in influencing the thermoelectric effect, a thermoelectric material whose Seebeck coefficient is high should be selected for achieving efficient thermocatalytic performance. Near room temperature, bismuth telluride (Bi2Te3) has a higher Seebeck coefficient30,31,32 than other common thermoelectric materials such as antimony telluride (Sb2Te3) and lead telluride (PbTe) due to its excellent physical properties and distinctive electronic structure33.

In this work, we demonstrate H2O2 generation and the consequent antibacterial activity of selected thermoelectric materials such as Bi2Te3, Sb2Te3, and PbTe. Since the early 1800s, H2O2 has been used as a disinfectant owing to its high oxidative and biocidal efficiency34. The thermocatalytic efficiency and subsequent H2O2 generation were further enhanced 20 times by narrowing down the Bi2Te3 size. For convenient applications, Bi2Te3 nanoplates (NPs) were coated on a carbon fiber fabric (Bi2Te3@CFF), and for simulating real-life conditions, Bi2Te3@CFF was utilized as a thermocatalytic filter under an indoor temperature difference. Bi2Te3@CFF exhibits significant antibacterial activity with either a positive or negative temperature difference and shows good durability as the antibacterial activity remains intact for more than one month. The concepts and results presented in this paper strongly highlight the bright prospects of thermocatalysts for H2O2 generation and environmental disinfection applications.

Results

Thermocatalytic performance of bulk thermoelectric materials

The concept of the thermocatalytic generation of H2O2 is illustrated in Fig. 1a. Bi2Te3 is a narrow bandgap semiconductor with a bandgap of ∼0.2 eV, and the conduction band potential of Bi2Te3 is more negative than the redox potential of O2/.O2−. In thermal equilibrium, free charges present on the crystal surface quickly exhaust before reacting with the contaminant solution because of the large potential difference between the conduction band and the redox potential of O2/.O2−. As a result, no significant catalytic activity is noticed. However, with the application of a temperature difference, negative charges rush from the hot side to the cold side of the material and produce a potential difference between the hot and cold ends. As a result of this thermoelectric potential, the band energy decreases at the positive potential side and increases at the negative potential side. To follow this variation in energy, both the valence band and conduction band tilt across the material and the conduction band comes very close to the redox potential for generating superoxide (.O2−) radicals. Consequently, electrons from the conduction band can easily migrate to the solution and produce H2O2 afterward via the reaction. O2− + e− + 2H+ → H2O2. However, the thermocatalytic property can be exclusively observed in thermoelectric materials, which are capable of producing electron-hole separation under an applied temperature difference. In previous studies, thermoelectric materials have been deployed to realize thermoelectric nanogenerators to harvest thermal energy from the environment and convert it into electrical energy35,36. In a similar way, it is expected that the temperature difference-induced potential of thermoelectric materials can be utilized for realizing efficient thermocatalysts.

Fig. 1: Thermocatalytic H2O2 generation by different bulk thermoelectric materials.
figure 1

a Schematic illustration of the thermocatalysis mechanism for H2O2 generation under a temperature gradient created due to applied temperature difference. Bi2Te3 is selected as a model thermoelectric material to explain the catalytic reaction. b H2O2 generation efficiency by three kinds of thermoelectric materials (Bi2Te3, Sb2Te3, and PbTe) and the typical photocatalyst TiO2 at ambient temperature and under a temperature difference of 20 K. c H2O2 generation efficiency by bulk Bi2Te3 (50 mg) under different temperature differences. d Disinfection performance of bulk Bi2Te3 (50 mg) under different applied temperature differences.

Full size image

Therefore, as an attempt to verify this concept, three kinds of commercially available bulk thermoelectric materials, Bi2Te3, Sb2Te3, and PbTe, (purchased from Alfa Aeser) were used for the thermocatalytic reactions (Fig. 1b). From the figure, it is evident that all thermoelectric materials can produce H2O2 under a temperature difference of 20 K. In contrast, the common photocatalyst titanium dioxide (TiO2) cannot produce H2O2 under the same conditions. The obtained results vividly verify the potential of the thermoelectric materials for using as thermocatalysts. Furthermore, the amount of H2O2 generated in the thermocatalytic reaction is strongly correlated with the Seebeck coefficient37 and the dimension of the thermoelectric materials. The Seebeck coefficient of both Sb2Te3 and PbTe is much smaller than Bi2Te3 in the low temperature range30,31,32, resulting in the highest amount of H2O2 production in the case of Bi2Te3. As any catalytic reaction is accelerated with a large surface area, the small size of Bi2Te3 is also responsible for demonstrating superior thermocatalytic activity as compared to Sb2Te3 and PbTe (Supplementary Fig. 1). It was also noticed that as the temperature difference was increased to 40 K, the efficiency of H2O2 generation by bulk Bi2Te3 reached approximately 0.34 μM/mg (Fig. 1c). The H2O2 generated by bulk Bi2Te3 under different temperature differences was further used to perform the bacterial disinfection experiments (Fig. 1d). In particular, the bacterial solution was treated with bulk Bi2Te3 under different thermal cycles to observe its disinfection performance. As the number of thermal cycles increases from 1 to 3, the disinfection performance of bulk Bi2Te3 increases gradually. This result also indicates that the disinfection performance has a positive correlation with the amount of H2O2 generated. In other words, higher H2O2 production caused by a higher temperature difference results in a better thermocatalytic effect and consequently a higher disinfection performance.

Control experiments also reveal that the presence of thermocatalysts and a temperature difference are both required for achieving disinfection performance (Supplementary Fig. 2). Moreover, it is also established that superoxide radicals are generated during the thermocatalytic reaction, which facilitates H2O2 generation (Supplementary Fig. 3). Hence, it is conclusively verified that the obtained disinfection performance is a consequence of the in-situ generation of H2O2 by the thermocatalyst under an applied temperature difference. It is also interesting to note that like other conventional catalysts, thermocatalysts also do not undergo any change in weight during H2O2 generation under multiple thermal cycles (Supplementary Fig. 4). Furthermore, when the temperature difference became negligible, no H2O2 was produced, which proved that H2O2 generation by the thermocatalyst was influenced by the applied temperature difference only (Supplementary Fig. 5).

Characterization and thermocatalytic activity of Bi2Te3 NPs

In an attempt to boost the thermocatalytic efficiency, nanometer-sized Bi2Te3 was synthesized via a wet chemical route, and the as-synthesized nanomaterials were characterized by various techniques. The FESEM image shown in Fig. 2a clearly indicates the formation of uniform hexagonal nanoplate-like nanomaterials. Moreover, AFM images also confirm that the thickness of the synthesized Bi2Te3 NPs is ~50 nm (Supplementary Fig. 6a and b). The uniform spatial dispersion of Bi and Te in a single NP is also confirmed from the elemental mapping obtained from EDX analysis (Fig. 2b). The synthesized NPs are highly crystalline in nature, which becomes evident from the HRTEM image exhibiting well-resolved lattice fringes with an interatomic spacing of 0.22 nm corresponding to the (110) planes of Bi2Te3 (Fig. 2b). The obtained hexagonal nanoplates also exhibit high phase purity, which is evidenced from their XRD pattern, as shown in Fig. 2c. All the XRD peaks are well-matched with JCPDS card no. 15-0863, corresponding to rhombohedral structured Bi2Te3 nanocrystals, thereby discarding any possibility of having an impure phase in the synthesized nanomaterials. Similar to their bulk counterpart, Bi2Te3 NPs also exhibit a thermocatalytic effect that can produce H2O2 in the presence of an applied temperature difference (Fig. 2d). Bi2Te3 NPs (5 mg) can generate up to 30 μM H2O2 with a temperature difference of 30 K. It is noteworthy that regardless of whether the temperature difference is positive or negative, H2O2 can still be generated.

Fig. 2: Characterization of Bi2Te3 NPs for H2O2 generation and disinfection performance.
figure 2

a SEM image demonstrating the uniform hexagonal nanoplate-like morphology of the synthesized nanomaterials. b HRTEM image and elemental mapping images revealing the well-resolved lattice fringes corresponding to the (110) plane and homogeneous distribution of Bi and Te in the as-prepared Bi2Te3 NPs, respectively. c XRD pattern of the as-prepared Bi2Te3 NPs. d H2O2 generation by the as-prepared Bi2Te3 NPs under different temperature differences. e Disinfection performance of the as-prepared Bi2Te3 NPs under various temperature differences and thermal cycles.

Full size image

Since the Seebeck coefficient of a thermoelectric material plays the pivotal role in controlling the thermocatalytic activity, the thermoelectric voltage and corresponding Seebeck coefficient of Bi2Te3 NPs are also estimated (Fig. 3). The thermoelectric device fabricated by Bi2Te3 NPs was subjected to a series of temperature difference by adjusting the temperature (40 to 100 °C) of a hot plate. When the temperature of the hot end of the device is increased from 40 to 100 °C, the generated thermoelectric voltage is also enhanced from 0.72 mV to 19.83 mV (Fig. 3a, b). The actual temperature difference created across the device is represented by the temperature distribution images as shown in Fig. 3a. The developed thermoelectric voltage is a consequence of temperature difference induced carrier migration within the Bi2Te3 NPs. The obtained thermoelectric voltages (ΔV) are plotted as a function of actual temperature difference (ΔT) and the slope obtained from the linear fitting of ΔV vs. ΔT curve denotes the Seebeck coefficient (S) (Fig. 3c). The synthesized Bi2Te3 NPs exhibit a high Seebeck coefficient of ~ 497 μV/K which strongly validates the potential of Bi2Te3 NPs to act as efficient thermocatalyst. It is noteworthy that when one end of the thermoelectric device is cooled keeping the other end at room temperature, the charge carriers within Bi2Te3 NPs move to a reverse direction and consequently the opposite output voltage signals are obtained (Supplementary Fig. 7). Moreover, it is also important to note that obtained thermoelectric voltage for applied +10 K temperature difference is higher (0.45 mV) than the generated thermoelectric voltage (0.19 mV) for −10 K temperature difference (Supplementary Fig. 7b). The impact of this phenomenon is vividly reflected from the H2O2 generation performance of Bi2Te3 NPs at different temperature differences as shown in Fig. 2d. The amount of H2O2 generated under a −10 K temperature difference (8.5 μM) is lower than that generated under a +10 K temperature difference (18 μM). Obtained results strongly signify that the generated thermoelectric voltage of a thermocatalyst plays a crucial role in controlling surface electrochemical reaction and consequent catalytic activity.

Fig. 3: Thermoelectric characterizations of Bi2Te3 NPs.
figure 3

a Demonstration of thermoelectric voltage generation by Bi2Te3 NPs at different heating temperatures. Corresponding actual temperature differences created across the device are represented by the temperature distribution images recorded by IR camera. b Variation of thermoelectric voltage with heating temperature ranging from 40 to 100 °C. c Slope of the linear fitting of ΔV vs. ΔT curve indicates the Seebeck coefficient.

Full size image

It is also interesting to note that H2O2 generation efficiency is significantly higher in the case of cyclic heating condition than the continuous heating condition (Supplementary Fig. 8). Since, for nanomaterials it is difficult to maintain the temperature difference for a long time, in the current work cyclic heating operation was used in which the thermocatalyst restores their initial temperature when they are kept back at room temperature after each heating step. The synthesized Bi2Te3 NPs were also used in disinfection experiments, and the results are shown in Fig. 2e. From the figure, it is evident that significant antibacterial activity was achieved under a temperature difference of 20 K, where only 5% of bacteria survived. However, control experiments revealed that bulk Bi2Te3 (5 mg) exhibited very little antibacterial activity under the same experimental conditions as Bi2Te3 NPs (Supplementary Fig. 9).

Temperature difference-induced voltage generation in the thermoelectric materials was further confirmed from the surface potential analysis carried out by Kelvin probe force microscopy (KPFM) incorporated with a thermal stage to heat the samples (Fig. 4a, b). While the surface of Bi2Te3 NPs does not show any surface potential in thermal equilibrium, with the application of a temperature of 60 °C, a ~280 mV response voltage is observed. When an applied temperature difference is imposed across the Bi2Te3 NPs, charge carriers with opposite polarity are separated from the surfaces, and as a result, the Bi2Te3 NPs gain more surface charges. Under this condition, to maintain the Fermi level alignment, the contact potential difference (CPD) between the KPFM tip and sample increases compared to thermal equilibrium conditions. A higher contact potential difference also indicates a reduction in the work function of Bi2Te3 under the applied temperature38. The observed output voltage is a direct consequence of temperature difference-induced electron-hole separation in Bi2Te3. Moreover, the generation of H2O2 by Bi2Te3 was tested under different environmental conditions, including O2, N2, and air. It was found that the N2-filled environment led to the generation of the lowest amount of H2O2, indicating that superoxide radical derivation from dissolved O2 was the key factor in H2O2 generation (Fig. 4c). It is also found that the increase in temperature difference boosts the thermocatalytic generation of superoxide radicals which is evidenced from Supplementary Fig. 10. Moreover, in order to prove that generation of superoxide radical is thermodynamically possible, the band edge position of Bi2Te3 NPs was determined with the help of high-resolution valence band XPS (Supplementary Fig. 11). The valence band maxima (VBM) is determined from the binding energy position at which the electronic density of states become zero. From Supplementary Fig. 11 it is clear that the VBM position of Bi2Te3 NPs is located at −0.41 eV which is in close agreement with the VBM position of Bi2Te3 reported previously39. Conduction band minima (CBM) positions are calculated from the equation ECB = EVB − Eg (Eg, ECB and EVB indicate the bandgap energy, conduction band potential, and valence band potential). Considering the bandgap of Bi2Te3 as 0.2 eV40, the CBM position is calculated to be −0.61 eV. The obtained conduction band potential is more negative than the redox potential of O2/·O2− (−0.33 eV vs. NHE)41,42. The more negative conduction band potential readily implies that formation ·O2− radical and consequent H2O2 generation is thermodynamically possible. Furthermore, the efficiency of H2O2 generation by the Bi2Te3 NPs was compared to that of bulk Bi2Te3 (Fig. 4d), revealing that the amount of H2O2 generated by Bi2Te3 NPs was at least 20 times higher than the amount generated by bulk Bi2Te3. Since catalysis is a surface phenomenon, the high surface area of the catalysts can effectively boost the surface chemical reactions by increasing the active catalytic sites. The 2D plate-like structure of Bi2Te3 NPs facilitates higher surface area than bulk Bi2Te3 which is responsible for this superior thermocatalytic acivity. The nanostructuring approach for realizing high surface area and efficient catalytic activity are already widely reported in the literature17,43. Moreover, since Bi2Te3 is a narrow bandgap semiconductor, it is necessary to find out if there is any contribution from photocatalysis in the thermocatalytic activities shown by Bi2Te3 NPs. In presence of ambient light, Bi2Te3 NPs exhibit almost similar catalytic performance as compared to dark (Supplementary Fig. 12). Actually, for the thermocatalysts, temperature difference induced thermoelectric voltage generation and consequent band bending is primarily responsible for reducing the energy difference between band energy and redox potential which is eventually not possible for a photocatalyst. Hence the obtained thermocatalytic performance remains almost unaffected from the interference of photocatalysis. These phenomena not only indicate that ambient light has negligible effect in the thermocatalytic activity offered by Bi2Te3 but also support the practical applicability of the thermocatalysts in the real circumstances.

Fig. 4: Temperature-induced surface potential evaluation and H2O2 generation.
figure 4

Thermoelectric voltage generation by the as-prepared Bi2Te3 NPs measured by KPFM equipped with a thermal stage a at room temperature and b at 60 °C. c H2O2 generation by the as-prepared Bi2Te3 NPs in different ambient conditions of O2, air, and N2 under a temperature difference of 20 K. d The efficiency of H2O2 generation by the as-prepared Bi2Te3 NPs compared to bulk Bi2Te3.

Full size image

Bi2Te3@CFF for antibacterial filter applications

The excellent disinfection performance of Bi2Te3 NPs was further employed to design an antibacterial filter with potential applications in our daily life. The antibacterial filter was fabricated by coating the Bi2Te3 NPs on a CFF, as illustrated in Fig. 5a. Here, CFF was chosen as an antibacterial filter because of its potential applications in textile industries. The uniform deposition of Bi2Te3 NPs over CFF is clearly visible from the FESEM images shown in Fig. 6a. Moreover, it is also interesting to note that the Bi2Te3 NPs retain their hexagonal shape even after dip-coating on the CFF. As expected, the developed antibacterial filter is capable of producing H2O2 by a thermocatalytic effect when it is exposed to a temperature difference (Supplementary Fig. 13). However, bare CFF does not exhibit any H2O2 generation under the applied temperature difference.

Fig. 5: Disinfection performance of thermocatalytic filter with cooling and heating effect.
figure 5

a Schematic illustration of the thermocatalytic filter developed by coating the as-prepared Bi2Te3 NPs on a commercial CFF. b, c Temperature profile of the thermocatalytic filter captured by an IR camera during exposure to cold air and hot air, respectively. The top insets show the illustration of creating a temperature difference by driving cold air and hot air onto the thermocatalytic filter. Bottom insets show the 3D temperature distribution images of the thermocatalytic filter. d, e Disinfection performance of Bi2Te3@CFF driven by cold air and hot air, respectively. Control experiments using the pure CFF indicate that no obvious disinfection performance was observed without the as-prepared Bi2Te3 NPs.

Full size image
Fig. 6: Real-time application of antibacterial filter and its reusability test.
figure 6

a SEM image of Bi2Te3@CFF after dip-coating. The inset shows the high magnification view of Bi2Te3@CFF representing uniform deposition of Bi2Te3 hexagonal nanoplates on the CFF. b SEM image of Bi2Te3@CFF after 30 days of use. c Reusability test demonstrating the disinfection performance of Bi2Te3@CFF for 30 days. The inset shows a digital photograph indicating the installation of Bi2Te3@CFF in the air conditioner.

Full size image

The temperature difference needed for H2O2 generation can also be harnessed from the surrounding environment. Cold air and hot air coming from a cooling fan and a hairdryer, respectively, were directed onto the front side of the Bi2Te3@CFF to produce a temperature difference through the filter. The produced temperature difference across the Bi2Te3@CFF filter is clearly evident from the real temperature distribution curve obtained from the thermal image, as shown in Fig. 5b, c. Since cold air was blown onto the front side, the temperature at the front side of the filter decreased to approximately 25 °C (Fig. 5b). On the other hand, the temperature on the front side increases to more than 45 °C when hot air was blown from a hairdryer (Fig. 5c). The disinfection performance of Bi2Te3@CFF was also probed under cold air or hot air treatment and compared with that of a commercially available unmodified CFF (Fig. 5d, e). The commercial unmodified CFF does not exhibit any antibacterial activity even upon the application of a temperature difference which is fully consistent with the poor H2O2 generation performance shown by bare CFF as represented in Supplementary Fig. 13. However, significant disinfection performance was achieved for Bi2Te3@CFF under the treatment of both cold and hot air. It is also interesting to note that since the achieved temperature difference across the Bi2Te3@CFF is higher for hot air treatment, the bacterial survivability (~28%) is also less in this condition as compared to cooling fan experiment. Moreover, it was also noticed that without the application of cold air or hot air, no antibacterial activity was observed, which proves the necessity of the thermocatalyst for effective antibacterial performance in the presence of a temperature difference.

For further practical applications of the thermocatalyst as a disinfectant of the indoor local environment, a large-sized Bi2Te3@CFF was fabricated for utilization as a domestic antibacterial filter. An air conditioner (AC) is a commonly used machine to control the temperature and humidity in indoor surroundings. Herein, we used an air conditioner as a platform to demonstrate the concept of indoor air purification technology. The antibacterial filter was installed in the air conditioner in such a way that it could be easily removed or changed. The temperature inside the air conditioner was lower than the air in the surroundings, creating a temperature difference to trigger the thermocatalytic reaction. Since the air conditioner was set at 17 °C, it can be concluded that the temperature difference across the Bi2Te3@CFF was similar to that in the case of cooling fan experiment. This fact is also clear from the disinfection results which reveal that thermocatalytic reaction at air conditioner also leads to ~ 60% bacterial degradation as in the case of cooling fan experiment. A comparison of the SEM image shown in Fig. 6a, b clearly indicates that Bi2Te3@CFF does not undergo any degradation even after 30 days of operation. XRD and Raman spectra of the Bi2Te3@CFF (Supplementary Fig. 14) also indicate that even after 30 days of thermocatalytic operation under air conditioner, the antibacterial filter retains their initial spectral characteristics. As a result of these, the antibacterial activity of the designed filter can be well retained even after 30 days of use (Fig. 6c). The obtained results strongly indicate the long-term stability and robustness of the designed antibacterial filter for practical disinfection applications.

Discussion

In summary, Bi2Te3-based thermocatalysts have been designed to demonstrate temperature difference-induced H2O2 generation in conjunction with bacterial disinfection. In particular, Bi2Te3 NPs were synthesized by a simple wet chemical route and deployed under a positive or negative temperature difference to realize surface electrochemical reaction-mediated ROS generation. As the temperature difference was increased to 30 K, the amount of H2O2 generated by the Bi2Te3 NPs was approximately 30 μM, which is ~20 times higher than that generated by bulk Bi2Te3. The thermoelectric voltage generated by Bi2Te3 NPs under a temperature difference is identified to play a decisive role in controlling the thermocatalytic ROS generation process. The concept of using thermoelectric materials for ROS generation was also verified by testing the thermocatalytic performance of other thermoelectric materials, such as Sb2Te3 and PbTe. Moreover, the Bi2Te3 NPs exhibit excellent disinfection performance by achieving 95% antibacterial activity (5% E. coli survival) after three thermal cycles. For the effective utilization of the developed catalysts in daily life applications, Bi2Te3 NPs were coated on a CFF and used as an antibacterial filter in a domestic air conditioner. As long as a temperature difference exists, the thermocatalyst can generate ROS to kill the bacteria. As a whole, the concepts presented here highly promote the merits of thermocatalysts for round-the-clock ROS generation that can open a new direction towards sustainable environmental remediation applications.

Methods

Synthesis of Bi2Te3 NPs

First, a stock solution was prepared by dissolving 0.8 g sodium hydroxide in 10 mL ethylene glycol at 45 °C in a water bath. Then, 0.1 g bismuth nitrate pentahydrate, 0.067 g sodium telluride, and 0.235 g polyvinylpyrrolidone (PVP) were loaded into a 25 mL three-neck flask, to which 10 mL stock solution was added. The mixture was stirred for 10 min at room temperature. After that, the three-neck flask was placed in the water bath at 45 °C for 20 min. Until the precursors were dissolved in the solution, a three-neck flask was kept in the oil bath and stirred for 3 h at 190 °C. After the reaction, 30 mL of isopropyl alcohol and 10 ml of acetone were added to the solution, and the mixture was centrifuged at 6700 × g for 10 min. The supernatant was discarded, and the process was repeated 3 times. Finally, the filtered Bi2Te3 NPs were redispersed in 30 mL of isopropyl alcohol and were used for further experiments.

Preparation of Bi2Te3@CFF

To clean the surface of the carbon fiber fabric, it was soaked in acetone, isopropanol, and DI water for 5 min, respectively. Then, the carbon fiber fabric was cut into a size of 1 × 1 cm and dipped in 100 μL of Bi2Te3 NP (1 mM) solution. Finally, the as-prepared carbon fiber was dried in a hot air oven to completely remove the water.

Characterization

X-ray diffraction (XRD, Rigaku TTRAX Ш) was employed to investigate the structural properties of the prepared nanomaterials. For XRD analysis, the Bi2Te3 NPs were coated on a glass slide and placed on a hot plate to remove water. The morphology of the Bi2Te3 NPs was analyzed by using scanning probe microscopy (SPM, Bruker). The morphology of the Bi2Te3@CFFs was analyzed via field emission scanning electron microscopy (FESEM, JEOL JSM-7600F). For FESEM analysis, the Bi2Te3 NPs were drop-coated on a Si wafer and placed in a 60 °C incubator overnight. Cs-corrected STEM (JEOL ARM200F) and energy dispersive spectrometry (EDS, Oxford INCA) were used to analyze the lattice and elemental distribution of the Bi2Te3 NPs, respectively. Amplitude modulated Kelvin probe force microscopy (AM-KPFM) equipped with a thermal stage was employed to monitor the surface potential distribution of the Bi2Te3 NPs. Raman spectra were recorded by a UniRam Raman spectrometer (ProTrus. Tech. Co. Ltd.) equipped with a 532 nm laser. Valence band XPS (VB-XPS) spectra were collected by X-ray photoelectron spectrometer (ESCALAB 250 XI, Thermo Scientific) having monochromatic Al Kα X-ray source.

Measurement of Seebeck coefficient

A device size of 1cm2 was used for the thermoelectric voltage measurement and a hot plate was used to create the temperature difference. For measuring the thermometric voltage below room temperature, a PID controlled cooling stage was used. The temperature difference between the surface of the hot-plate/cooling stage and the top surface of device induces temperature difference across the device and the consequent thermoelectric voltage is generated. The generated thermoelectric voltages were recorded with a low noise voltage preamplifier (SR-560). To determine the actual temperature difference created across the device, the temperature at the surface of the hot-plate (T1) and top of the device (T2) were monitored with the help of IR camera.

Preparation of E. coli for the disinfection test

E. coli K12 cells were grown in lysogeny broth (LB) medium. The original E. coli K12 cells were added to LB medium for 16 h at 37 °C in an incubator. After 16 h, the E. coli K12 cells were diluted to an optical density of 0.06 at 670 nm (OD670 = 0.06). Then, the bacterial cell suspension was diluted 10 times in 0.85% sodium chloride, which was equal to 2 × 107 CFU per 1 mL for the antibacterial investigation.

Thermocatalytic disinfection test

Thermocatalysis experiments were conducted in a water bath where the thermocatalysts in the contaminant solutions were subjected to 3 thermal cycles denoted as C1, C2, and C3. In each cycle, the materials at first were allowed to react at specific temperature (15/35/45 °C) for 5 min and then were returned to room temperature (RT) for 5 min. Two separate groups of experiments were carried out, one without a thermal cycle (under RT) and the other with thermal cycles. The materials were bulk Bi2Te3 and Bi2Te3 NPs. The masses of the bulk Bi2Te3 and Bi2Te3 NPs were 0.05 g and 0.005 g, respectively. These materials were added to 1 mL bacterial solution (2 × 106 CFU per 1 mL) for the thermocatalysis experiments.

Detection of ·O2 - and H2O2 generated by the thermocatalysts

The generation of superoxide radicals during the thermocatalysis reaction was estimated quantitatively by using XTT (2, 3-bis (2- methoxy-4-nitro-5-sulfophehyl)−2H-tetrazolium-5-carboxanilide) assay. Typically, aqueous dispersion of bulk and Bi2Te3 NPs were mixed with XTT (50 μM) and then, the solution was subjected to different temperature difference at water bath. After the reaction Bi2Te3 was separated by centrifugation and the absorbance spectra of supernatants were monitored at 470 nm.

Amplex Red reagent with HRP enzyme was used for H2O2 detection. In general, Amplex Red reacts with H2O2 to produce the red-fluorescent oxidation product resorufin. First, two different stock solutions were prepared. One was 0.4 mg Amplex Red powder dissolved in 3.1 mL dimethyl sulfoxide (DMSO), and the other was 0.5 mg of HRP dissolved in phosphate-buffered saline (PBS, pH 5.8). The materials (bulk Bi2Te3, bulk Sb2Te3, bulk PbTe, bulk TiO2, Bi2Te3 NPs, Bi2Te3@CFFs) were first added to a 1 mL sodium chloride (0.85% NaCl) solution, and the solution was then kept in a water bath for 15 min where it was subjected to different temperatures (10, 15, 35, 45, 55, 65 °C). After the temperature treatment, the solution was filtered by a 0.2 µm PVDF membrane filter, and 270 µL of filtrate solution was added to a mixture of 30 µL Amplex Red solution and 3 µL HRP solution. A photoluminescence spectrophotometer (HITACHI F-7000) was used to detect the generated fluorescent product. The samples were excited at 530 nm, and emission spectra were scanned from 560~750 nm.

Disinfection test by the antibacterial filter

To demonstrate the performance of Bi2Te3@CFF as an antibacterial filter, the disinfection tests were conducted using a hairdryer and a cooling fan. At first 1 mL of bacterial solution (2 × 106 CFU/mL) was added to 1 × 1 cm Bi2Te3@CFF and further treated for a total time of 20 min under the temperature difference created by hairdryer and cooling fan. Control experiments were also performed under the same conditions without the temperature difference. Both the treated and untreated Bi2Te3@CFF were immersed in 1 mL of 0.85% sodium chloride solution. Aliquots of 100 μL of bacterial solution were collected from each group and plated on an aseptic plate. The bacterial colonies were counted from the plates after 24 h of incubation at 37 °C. The survival rates were determined by using the formula C/C0 × 100% where C0 is the concentration of the bacteria solution before thermal treatment and C is the remaining concentration of the bacteria after the thermal treatment.

Reusability test of the antibacterial filter

This test was conducted by using an air conditioner. Bi2Te3@CFF with dimensions of 8 × 15 cm was mounted on an indoor part of a split air conditioner. The temperature of the air conditioner was set to 17 °C in order ensure similar range of temperature difference as in case of cooling fan experiment. In this case, the same bacterial concentration (2 × 106 CFU/mL) was used to react the Bi2Te3@CFF as in the case of cooling fan experiment. The treatment was the same as the air for the disinfection test. The treatment was repeated for 30 days.

Reporting Summary

Further information on research design is available in the Nature Research Reporting Summary linked to this article.